Caterpillar cat 450 e backhoe loader (prefix lyr) service repair manual (lyr00001 and up)

Service Repair Manual
Models
450E Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 450E BACKHOE LOADER LYR
Configuration: 450E Backhoe Loader LYR00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
450E Backhoe Loader Machine Systems
Media Number -UENR0271-02 Publication Date -01/04/2017 Date Updated -25/04/2017
i02485140
Piston Pump - Disassemble
SMCS - 5070-015; 5455
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0074 Slide Hammer Puller 1
B 1P-0510 Driver Group 1
C 1P-1858 Retaining Ring Pliers 1
D 8H-0663 Bearing Puller Assembly 1
E 166-7441 Valve Seat Extractor Tool 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/17450E Backhoe Loader LYR00001-UP (MACHINE) POWERED BY C4.4 Engine(SE...
2019/12/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01240851
1. Remove solenoid assembly (1A) and tube assembly (1B).
2. Remove tube assembly (3). Remove bolts (1) and pressure and flow compensator valve (2).

Note: Mark the position of valve (5) for assembly purposes.
3. Remove O-ring seals (4) and valve (5).
4. Remove orifice (6).
5. Remove adapter assembly (7) and connector (8). Remove the seals from adapter assembly
(7) and connector (8).

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: Record Dimension (X) and Dimension (Y) for assembly purposes. The dimension is
from the top of the nuts to the top of the screws.
6. Remove valve assembly (9).
7. Remove nut (17), plug (16), screw (15), and seat (14). Remove springs (13) and (12).
Remove retainer (11) and stem (10). Remove seal (18) and seal (19).

8. Remove valve assembly (20).
9. Remove nut (28), plug (27), screw (26), and seat (25). Remove springs (24) and (23).
Remove retainer (22) and stem (21). Remove seal (29) and seal (30).

10. Remove plugs (31) and (32). Remove the seals from plugs (31) and (32).
11. Remove bolts (33) and power compensator valve (34).
12. Remove plug (35), O-ring seal (36), and fitting (37).

13. Remove O-ring seal (38) and cap (39).
14. Use Steps 15 and 16 in order to disassemble power compensator valve (34).

15. Remove nut (51) and adjuster (49). Remove plug (50) from adjuster (49). Remove O-ring
seal (48), spring (47), and retainer (46).
16. Remove plug (40). Remove O-ring seal (41) from plug (40). Remove spring (42), retainer
(43), piston (44), and stem (45).
17. Remove bolt (53), carrier (52), and pin (54).
Personal injury can result from parts under high spring pressure.

Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
Note: Mark the position of head assembly (56) to aid in installation.
18. Remove bolts (55) and head assembly (56).
19. Remove O-ring seal (57) and port plate (58).
20. Remove piston (59) and spacer (60).

21. Remove plunger (61) and spring (62).
22. Remove cylinder (63) and guide (64).
23. Remove pin (65).
10/17450E Backhoe Loader LYR00001-UP (MACHINE) POWERED BY C4.4 Engine(S...

24. Use Tooling (A) in order to remove bearing cup (66).
25. Remove O-ring seal (67) and bearing cone (68).
26. Remove spacer (69).

27. Remove rotating group (70).
28. Remove piston assemblies (71) and plate (72).
29. Remove bearing (73).

Personal injury can result from parts under high spring pressure.
Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
30. Use a suitable press and Tooling (B) in order to compress the spring. Use Tooling (C) in
order to remove retaining ring (74).
31. Remove spring (76) and seat (75).

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

32. Remove pins (77).
33. Remove swashplate assembly (78).
34. Remove bolt (79) and carrier (80).

35. Remove bearing races (81) and (82).
36. Remove shaft assembly (83).
37. Use a suitable press and Tooling (D) in order to remove bearing cone (84) from shaft (83).

38. Use Tooling (E) in order to remove bearing cup (85).
39. Remove seal (86).
40. Use Tooling (F) in order to remove retaining ring (87).

Caterpillar cat 450 e backhoe loader (prefix lyr) service repair manual (lyr00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (13)

Similar to Caterpillar cat 450 e backhoe loader (prefix lyr) service repair manual (lyr00001 and up)

Similar to Caterpillar cat 450 e backhoe loader (prefix lyr) service repair manual (lyr00001 and up) (18)

More from fjsexswkfkmsem

More from fjsexswkfkmsem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 450 e backhoe loader (prefix lyr) service repair manual (lyr00001 and up)