Call Girls Kanakapura Road Just Call 👗 7737669865 👗 Top Class Call Girl Servi...
Yale a839 erc120 hg lift truck service repair manual
1. ERC070-120HG (A839)
SERVICE MANUAL CONTENTS
SECTION
PART
NUMBER
YRM
NUMBER
REV
DATE
FRAME............................................................................................................................ 524166809 0100 YRM 0284 03/03
DC MOTOR MAINTENANCE.......................................................................................... 524158039 0620 YRM 0294 03/08
DRIVE AXLE, SPEED REDUCER, AND DIFFERENTIAL............................................. 524166834 1400 YRM 0413 11/06
STEERING CONTROL UNIT.......................................................................................... 524166835 1600 YRM 0257 05/02
STEERING AXLE............................................................................................................ 524150783 1600 YRM 0326 03/07
STEERING SYSTEM...................................................................................................... 524166836 1600 YRM 0485 07/03
BRAKE SYSTEM............................................................................................................ 524166837 1800 YRM 0338 05/09
HYDRAULIC SYSTEM.................................................................................................... 524166838 1900 YRM 0286 07/02
MAIN CONTROL VALVE................................................................................................ 524166839 2000 YRM 0077 02/09
TILT CYLINDERS........................................................................................................... 524150790 2100 YRM 0103 03/07
ELECTRICAL SYSTEM.................................................................................................. 524166840 2200 YRM 0560 07/05
EV-100ZX SCR MOTOR CONTROLLER PARAMETER TABLES................................ 524179949 2200 YRM 0595 07/03
DISPLAY PANEL FOR SEM CONTROLS (DOS VERSION)......................................... 524166842 2200 YRM 0725 07/02
TRANSISTOR MOTOR CONTROLLERS (SR AND SP) DESCRIPTION, CHECKS,
ADJUSTMENTS, TROUBLESHOOTING, REPAIRS AND THEORY OF
OPERATION.............................................................................................................. 524166843 2200 YRM 0808 06/05
DISPLAY PANEL FOR SEM CONTROLS..................................................................... 524166844 2200 YRM 0942 08/07
SR(SEM)/SP TROUBLESHOOTING AND ADJUSTMENTS WITH A COMPUTER
(WINDOWS VERSION).............................................................................................. 524167640 2200 YRM 0947 08/07
INDUSTRIAL BATTERY................................................................................................. 524158040 2240 YRM 0001 09/14
LIFT CYLINDERS........................................................................................................... 524150794 4000 YRM 0135 03/11
VISTA MASTS-DESCRIPTION AND REPAIRS............................................................. 524166845 4000 YRM 0340 09/02
MASTS............................................................................................................................ 524153920 4000 YRM 0736 07/10
LIFT CYLINDER.............................................................................................................. 524153919 4000 YRM 0741 03/05
METRIC AND INCH (SAE) FASTENERS....................................................................... 524150797 8000 YRM 0231 10/13
PERIODIC MAINTENANCE............................................................................................ 524166846 8000 YRM 0915 07/02
CAPACITIES AND SPECIFICATIONS........................................................................... 524166847 8000 YRM 0916 12/03
DIAGRAMS..................................................................................................................... 524166848 8000 YRM 0917 01/04
Service information for Cummins diesel engines can be ordered through the Hyster Literature Distribution Center.
PART NO. 524166807 (09/14)
2. 100 YRM 284 Description
General
This section has a description and the service procedures for the parts of the frame. These parts include the frame,
counterweight assembly, overhead guard, hydraulic tank, access panels, and label positions. See Figure 1. The
procedure for removing the traction motor is also described in this section.
Description
The frame is a single weldment. The frame has mounts
for the counterweight, overhead guard, tilt cylinders,
steering axle, and drive axle assembly. See Figure 1.
The hydraulic tank is part of the lift truck frame and is
a welded steel unit. The lift trucks must have a hood
over the battery or a covered battery if a hood is not
installed. The floor plates can be removed for access
to the hydraulic systems. A panel in the bottom of the
battery compartment can be removed for access to
the traction motor and the hydraulic pump motor. This
panel also gives access to the power steering pump
motor. The SCR (silicon controlled rectifier) electronic
controller and contactors are in the counterweight. A
panel in the counterweight can be removed for access
to the SCR controller and contactors.
The ERC070-120HG models are made with two sizes of
frames. A short frame (1018 mm battery compartment)
is available for the ERC070-80HG and the ERC100HG
models. A long frame (1183 mm battery compartment)
is available for the ERC100-120HG models. The size of
the battery compartment and battery size specifications
are shown in Table 1.
1. OVERHEAD GUARD
2. COUNTERWEIGHT
3. STEERING AXLE AND
WHEELS
4. FRAME
5. DRIVE AXLE AND WHEELS
6. MAST
7. FORKS
8. CARRIAGE
9. LOAD BACKREST EXTENSION
10. ACCESS PANEL TO SCR
ELECTRONIC CONTROLLER
Figure 1. Lift Truck Parts
1
3. Description 100 YRM 284
Table 1. Battery Specifications
Weight
Model Volts
Minimum
Compartment
Size Length ×
Width
Battery Length
Min./Max. Minimum Maximum
ERC070-080HG 36 841 × 987 mm
(33.1 × 38.9 in.)
950/990 mm
(37.4/39.0 in.)
1542 kg
(3400 lb)
2400 kg
(5292 lb)
ERC100HG (Short Frame) 36 841 × 987 mm
(33.1 × 38.9 in.)
950/990 mm
(37.4/39.0 in.)
1633 kg
(3600 lb)
2400 kg
(5292 lb)
ERC100HG (Long Frame) 36 694 × 1037 mm
(27.3 × 40.8 in.)
1115/1150 mm
(43.9/45.3 in.)
1814 kg
(4000 lb)
2700 kg
(5954 lb)
ERC120HG 36 993 × 1146 mm
(39.3 × 45.1 in.)
1115/1150 mm
(43.9/45.3 in.)
1919 kg
(4231 lb)
2700 kg
(5954 lb)
ERC070-080HG 48 841 × 987 mm
(33.1 × 38.9 in.)
950/990 mm
(37.4/39.0 in.)
1542 kg
(3400 lb)
2400 kg
(5292 lb)
ERC100HG (Short Frame) 48 841 × 987 mm
(33.1 × 38.9 in.)
950/990 mm
(37.4/39.0 in.)
1633 kg
(3600 lb)
2400 kg
(5292 lb)
ERC100HG (Long Frame) 48 694 × 1037 mm
(27.3 × 40.8 in.)
1115/1150 mm
(43.9/45.3 in.)
1814 kg
(4000 lb)
2700 kg
(5954 lb)
ERC120HG 48 993 × 1146 mm
(39.3 × 45.1 in.)
1115/1150 mm
(43.9/45.3 in.)
1919 kg
(4231 lb)
2700 kg
(5954 lb)
Battery Width
Batteries Without Cover: 950 to 1117 mm (37.4 to 44.0 in.)
Batteries With Cover: 950 to 1143 mm (37.4 to 45.0 in.)
NOTE: Maximum tolerances are +0 and 13 mm (+0 and 0.5 in.) for the size of the battery compartment. The
battery specification chart shows the maximum size tolerances that will permit the battery to still fit into a battery
compartment.
The lift trucks are equipped with adjustable spacers in
the battery compartment. See Figure 2. Add or remove
shims from under the front spacer bar to control the
movement of the battery in the forward and backward
directions. Install an equal number of shims at each
capscrew. Install the additional shims under the nuts
of the capscrews (outside battery compartment). The
spacers on each side of the battery can be adjusted to
control the movement of the battery from side to side.
Access to the nuts for the spacers for the sides of the
battery is under the frame near the steer tires on all
units. Tighten all capscrews. It can be necessary to
install the side spacers facing the opposite direction for
some batteries. If the spacers cannot be adjusted for a
battery that is specified for this lift truck, see your Yale
lift truck dealer for the correct spacers.
NOTE: Maximum tolerances are +0 and 13 mm (+0
and 0.5 in.) for the size of the battery compartment.
The battery specification chart shows the maximum
size tolerances that will permit a battery to still fit into a
battery compartment.
2
4. 100 YRM 284 Description
A. FRONT SPACER
1. BATTERY COMPARTMENT
2. BATTERY
3. BULKHEAD
4. SPACER BAR
5. SHIM
6. STORE ADDITIONAL SHIMS IN FRONT OF
BULKHEAD
Figure 2. Battery Compartment Shims
WARNING
The battery must fit the battery compartment so
that the battery restraint system will operate cor-
rectly. Use spacers to prevent the battery from mov-
ing more than 13 mm (0.5 in.) in any horizontal di-
rection.
The weight of the battery is a large part of the coun-
terweight system on an electric lift truck. Make sure
that the battery is within the weight limits indicated on
the nameplate. Each model of lift truck has a cast-iron
counterweight that provides the additional weight nec-
essary for the indicated capacity. A slot in the overhead
guard permits removal of the battery without removing
the overhead guard.
3
5. Overhead Guard Repair 100 YRM 284
Overhead Guard Repair
REMOVE
WARNING
Do not operate the lift truck without the overhead
guard correctly fastened to the lift truck.
1. Remove battery as described in the section Peri-
odic Maintenance for your lift truck.
2. Access to capscrews that hold rear supports of
overhead guard to counterweight is from the bat-
tery compartment. Remove capscrews.
3. Remove two capscrews that hold each front sup-
port of overhead guard to cowl. Disconnect any
electric wires from under cowl that go through sup-
ports of overhead guard. When overhead guard is
lifted from the frame, make sure these electric wires
move through the holes in the frame so they are not
damaged.
4. Use lifting device or another person to help lift over-
head guard from lift truck.
INSTALL
Put overhead guard on lift truck. Install any electric
wires from overhead guard supports through holes in
cowl. Install four capscrews, washers, and nuts that
hold front supports to cowl. Tighten capscrews to cor-
rect torque. Install capscrews and washers that hold
rear supports to counterweight. Tighten capscrews to
correct torque. The correct torque values are shown in
Figure 3. Install battery.
Figure 3. Frame, Overhead Guard, and Counterweight
4
6. 100 YRM 284 Battery Restraint and Seat Assembly Repair
Legend for Figure 3
Torque Values
Overhead Guard Counterweight
Model
Front Rear Upper Lower
ERC070-120HG 86 N•m (64 lbf ft) 86 N•m (64 lbf ft) 270 N•m (200 lbf ft) 66 N•m (49 lbf ft)
1. OVERHEAD GUARD (OHG)
2. COUNTERWEIGHT (CWT)
3. FRAME
4. CAPSCREWS (4) OHG-FRONT
5. CAPSCREWS (2) OHG-UPPER
6. CAPSCREWS (2) CWT-UPPER
7. CAPSCREWS (2) CWT-LOWER
Battery Restraint and Seat Assembly Repair
A battery restraint system is installed as a safety device.
The function of the battery restraint system, when cor-
rectly locked in the down position, is to hold the battery
in the battery compartment if an accident causes the lift
truck to tip over. The battery restraint is a steel plate
that is connected to the frame with a hinge. A sliding
latch mechanism locks the battery restraint in the down
position for operation. A knob near the hinge unlocks
the battery restraint from the frame so the battery re-
straint can be raised to the up position for access to the
battery. The battery restraint is also the support for the
seat. A spring brace holds the seat and battery restraint
in the up position. The operator must hold the seat as-
sembly with one hand. Use the other hand on the knob
to release the spring brace and lower the seat and bat-
tery restraint assembly to the operating position. Make
sure that the battery restraint is correctly locked to the
frame for operation of the lift truck.
An additional battery retention bar is used where bat-
teries can be longer. This bar has a hinge fastened to
the counterweight and is part of the hood mechanism
on lift truck with hoods. The bar is also installed on lift
trucks without hoods.
Spacers are used inside the battery compartment to
prevent horizontal movement of the battery.
WARNING
The battery restraint and its latch mechanisms
must operate correctly before a lift truck is oper-
ated. Make sure the battery has a cover if the lift
truck does not have a hood.
To operate correctly, the battery restraint plate must be
locked in the down position. The battery retention bar
(and hood) must be lowered first; then the battery re-
straint plate is locked in the down position over the bar.
The battery must have spacers to prevent movement in
any one horizontal direction of 13 mm (0.5 in.) maxi-
mum. See Figure 4. Use the knob near the hinge to
release the battery restraint plate. Use the handle on
the restraint plate to raise the plate and seat. A spring
brace will hold the assembly in the up position. If in-
stalled, raise the hood. Make sure that the battery can-
not move more than a total of 13 mm (0.5 in.) in any one
horizontal direction. Make sure the correct spacers are
installed to prevent the movement. See your Yale lift
truck dealer to replace damaged or missing spacers. If
a smaller battery of the correct weight (see nameplate)
is installed and the spacers cannot prevent movement,
your Yale lift truck dealer has larger spacers. Push the
seat and the battery restraint down until the latch locks.
Make sure battery restraint is locked securely. Lift on
battery restraint to make sure it is latched and will not
move.
5
7. Battery Restraint and Seat Assembly Repair 100 YRM 284
Figure 4. Battery Restraint and Seat Assembly
Legend for Figure 4
1. SEAT
2. BATTERY RESTRAINT PLATE
3. KNOB FOR LATCH MECHANISM
4. HINGE
5. LATCH
6. SPRING BRACE
7. BATTERY RETENTION BAR
SEAT BRAKE ASSEMBLY, ADJUST
1. Put a weight in the seat to release seat brake. Mea-
sure dimension X and Y. Add or remove shims un-
der clamp so dimension Y is equal to dimension X
within ±3 mm (0.12 in.). Use equal number shims
under each clamp. See Figure 5.
2. Adjust setscrew at top of lever so bottom of lever
equals dimension L from front plate of battery com-
partment.
NOTE: This adjustment can be made with the spring
assembly removed from the lift truck.
3. Adjust spring adjustment so length is dimension J.
4. On 280 mm (11 in.) diameter motor: Adjust lever
to a level position using nut. On 330 mm (13 in.)
diameter motor: Adjust lever to 25 ±2 mm (1
±0.08 in.) using nut. Lock nut with jam nut. Make
sure this adjustment does not apply the brake. See
Table 2.
5. Adjust spring to dimension K. Lock nut with jam nut.
This adjustment can be made with spring assembly
removed from lift truck.
6. Adjust position of rod end so brake will start to apply
when brake lever is raised 3 mm (0.12 in.) or less.
Rotate brake drum by hand to feel brake start to
apply.
7. Test operation of seat brake to make sure seat
brake is actuated correctly. Make sure linkage is
adjusted to correct measurements. If seat brake
does not correctly actuate brake after adjustments
have been made, adjust length of rod again and
make sure dimension is correct.
8. The seat can be removed from the battery restraint
plate. Remove four bolts. The battery restraint
plate can be removed from the frame. Remove
hinge pin that holds assembly to frame.
6
8. 100 YRM 284 Battery Restraint and Seat Assembly Repair
Table 2. Seat Brake Adjustment
Dimension
Motor Dia. Seat Type
J K L
Standard 80 mm (3.2 in.)*
280 mm (11 in.)
Suspension 75 mm (2.9 in.)
173 mm (6.7 in.) 65 mm (2.5 in.)
Standard 85 mm (3.3 in.)**
330 mm (13 in.)
Suspension 80 mm (3.2 in.)
165 mm (6.5 in.) 55 mm (2.1 in.)
* 90 mm (3.5 in.), ** 80 mm (3.2 in.) on early models.
Figure 5. Seat Brake Assembly
Legend for Figure 5
1. CLAMP
2. LEVER
3. SPRING ADJUSTMENT
4. BEARING
5. FRONT PLATE BATTERY COMPARTMENT
6. SPRING ASSEMBLY
7. MOTOR LEVER
8. MOTOR LEVER
9. SPRING
10. JAM NUT
11. JAM NUT
12. ADJUSTMENT NUT
13. ADJUSTMENT NUT
14. JAM NUT
15. SETSCREW
16. MOTOR 280 mm (11 in.)
17. MOTOR 330 mm (13 in.)
18. BRAKE
19. SEAT
7
9. Counterweight Repair 100 YRM 284
Counterweight Repair
If the lift truck must be put on blocks for maintenance
and repair, see Periodic Maintenance 8000 YRM 915
section How to Put a Lift Truck on Blocks.
WARNING
The counterweight is very heavy. Make sure that the
crane and lifting devices have enough lifting capac-
ity to safely lift the counterweight. The weights of
the counterweights are shown in Table 3.
The counterweight normally is not removed for most
repairs. Replacement of some large parts of the SCR
electronic controller is easier when the counterweight
is removed. The counterweight is fastened to the frame
with four capscrews. The weights for the counter-
weights are in Table 3.
Table 3. Counterweights
Model Weight*
ERC070HG 775 kg (1705 lb)
ERC080HG 1184 kg (2605 lb)
ERC100HG (Long Frame) 1184 kg (2605 lb)
ERC100HG (Short Frame) 1747 kg (3850 lb)
ERC120HG 1797 kg (3950 lb)
*Maximum weight
REMOVE
1. Remove battery. See the Periodic Maintenance
8000 YRM 915 section of this manual under How
to Change the Battery.
2. Remove overhead guard as described in the para-
graphs under Overhead Guard Repair, Remove.
3. ERC070-120HG models have a hole on top of the
counterweight for a single eye bolt. Attach chain or
sling to eyebolts. Use crane to hold the weight of
the counterweight. See Figure 3 and Figure 6.
4. From inside the battery compartment, remove two
capscrews that hold counterweight to frame. Re-
move two capscrews from tow pin area of counter-
weight. Use crane to lift counterweight away from
frame. Make sure you do not damage the electronic
controls.
NOTE: ERC120HG MODEL SHOWN.
1. LIFTING EYEBOLT
2. CAPSCREWS
3. TOW PIN
Figure 6. Lift Counterweight
INSTALL
NOTE: The access panel to the electronic controller can
be removed from the counterweight to make checks and
adjustments on the controller. Make sure lugs are cor-
rectly engaged when access panel is installed again or
panel will fall from counterweight during operation.
1. Use crane to lift counterweight into position. Make
sure you do not damage electronic controller. In-
stall two upper capscrews from inside battery com-
partment that hold counterweight to frame. Install
two lower capscrews in tow pin area of counter-
weight. Tighten capscrews to correct torque. The
correct torque values for capscrews are shown in
Figure 3.
2. Disconnect sling or chain. Remove eyebolts from
counterweight.
3. Install overhead guard as described in the para-
graphs for the Overhead Guard Repair, Install.
4. Install battery. See Periodic Maintenance 8000
YRM 915 section How to Change the Battery.
8
10. 100 YRM 284 Traction Motor Repair
Traction Motor Repair
REMOVE
This procedure will show the removal of the traction mo-
tor through the battery compartment. Some lift trucks
have a seat brake that actuates the brake on the arma-
ture shaft of the traction motor. See Figure 7. The seat
brake linkage must be disconnected at the front of the
traction motor before the motor is removed.
A. TRACTION MOTOR
B. TRACTION MOTOR WITH OPTIONAL SEAT
BRAKE
Figure 7. Traction Motor
NOTE: The traction motor can also be removed from
under the lift truck with the use of a floor jack, but is more
difficult. The lift truck must be on blocks with clearance
for the jack and traction motor if the traction motor is
removed from under the lift truck. The hydraulic lines
from the hydraulic tank must also be disconnected if the
traction motor is removed from under the lift truck.
1. Remove battery. Remove floor plates and access
panel in bottom of battery compartment.
2. Disconnect seat brake linkage. Disconnect hy-
draulic line to main control valve so motor mount
can be disconnected. Put caps on open hydraulic
fittings.
3. Disconnect power cables from traction motor. Make
an identification of which cable is connected to each
terminal.
4. Put lift truck on blocks for easier access to bottom
bolts between traction motor and speed reducer.
Remove bolts between speed reducer and motor.
5. Install sling to hold traction motor. See Figure 8.
Use wood block and board under sling as shown
in the illustration to control traction motor during re-
moval and installation. Use crane to hold weight of
traction motor. See Figure 9.
1. SLING
2. USE WOOD BLOCK AND BOARD UNDER SLING
FOR A LEVER
3. TRACTION MOTOR
Figure 8. Sling Installation to Lift Traction Motor
9
11. Hydraulic Tank Repair 100 YRM 284
Figure 9. Use Crane to Lift Traction Motor
NOTE: The traction motors are in different configura-
tions for different applications of the lift trucks. Trac-
tion motors weigh approximately 90 to 140 kg (200 to
310 lb). Make sure the sling cannot slide and permit
traction motor to fall.
6. Remove motor mount that holds traction motor to
frame. Pull traction motor from speed reducer.
7. Use crane to move traction motor to a space to
make repairs.
INSTALL
1. Install sling to lift traction motor. Use wood block
and board under sling as shown in Figure 8 to con-
trol traction motor during installation.
2. Lower traction motor into position in lift truck. Align
traction motor with speed reducer. See Figure 10.
3. Use board or prybar as necessary to push traction
motor into speed reducer.
4. Align bolt holes in speed reducer and motor hous-
ing. Install bolts that hold traction motor to speed
reducer. Tighten bolts to 38 N•m (28 lbf ft).
5. Remove sling and install traction motor mount.
6. Connect inlet hydraulic line to main control valve.
Install power cables.
1. SLING
2. BOARD
3. WOOD BLOCK
Figure 10. Align Traction Motor with Speed
Reducer
Hydraulic Tank Repair
INSPECT
Make a visual inspection of all sides of the tank. Inspect
welds for cracks and leakage. Check for wet areas,
accumulation of dirt, and loose or missing paint caused
by leakage. Areas of the tank that are not easily seen
can be checked with an inspection mirror and a light that
is approved for locations with flammable vapors.
The hydraulic tank is part of the frame weldment and
cannot be removed from the lift truck. See Figure 11.
Repairs for leaks in the hydraulic tank can require spe-
cial procedures described in the next paragraphs.
SMALL LEAKS, REPAIR
Use the following procedure to seal small leaks:
1. Use steam to clean area around leak. Remove all
paint and dirt around leak.
10
12. 100 YRM 284 Hydraulic Tank Repair
1. HYDRAULIC TANK
2. OUTER FRAME
3. INNER FRAME
4. SUCTION PIPE
Figure 11. Hydraulic Tank
WARNING
Do not use tools that can make sparks, heat, or
static electricity. The vapors in the tank can cause
an explosion.
2. Apply Loctite®
290 to leak. Follow instructions of
manufacturer.
LARGE LEAKS, REPAIR
1. Use one of the procedures described under Clean
in this section to clean and prepare the tank for
repairs.
2. Use acceptable welding practices to repair tank.
See the American National Standard Safety In
Welding and Cutting ANSI Z 49.1 - 1973.
CLEAN
WARNING
Special procedures must be followed when large
leaks or other repairs need welding or cutting. All
work must be done by authorized personnel. If the
tank is cleaned inside of a building, make sure there
is enough ventilation. See the following manuals
for additional information:
• Safe Practices for Welding and Cutting Contain-
ers That Have Held Combustibles by the Ameri-
can Welding Society, A6.0-65.
• Safety In Welding and Cutting, American National
Standard, ANSI Z 49.1 - 1973.
When cleaning tank, do not use solutions that make
dangerous gases at normal temperatures or when
heated. Wear eye and face protection. Protect the
body from burns.
When cleaning with steam, use a hose with a minimum
diameter of 19 mm (0.75 in.). Control the pressure of
the steam by a valve installed at the nozzle of the hose.
If a metal nozzle is used, it must be made of a material
that does not make sparks. Make an electrical connec-
tion between nozzle and tank. Connect ground wire to
tank to prevent static electricity.
Steam Method
Use the following procedure to clean the tank with
steam:
1. Remove all parts from tank. Install drain plug.
2. Fill tank 1/4 full with a solution of water and sodium
bicarbonate or sodium carbonate. Mix 0.5 kg (1 lb)
per 4 liter (1 gal) of water.
3. Mix solution in tank using air pressure. Make sure
all surfaces on inside of tank are flushed with solu-
tion. Drain tank.
4. Put steam into tank until tank does not have odors
and metal is hot. Steam vapors must come from all
openings.
5. Flush inside of tank with boiling water. Make sure
all loose material is removed from inside of tank.
6. Make inspection of inside of tank. If it is not clean,
repeat Step 4 and Step 5 and make another inspec-
tion. When making inspections, use a light that is
approved for locations with flammable vapors.
7. Put plugs in all openings in tank. Wait 15 minutes,
then remove inlet and outlet plugs. Test a sample of
the vapor with a special indicator for gas vapors. If
the amount of flammable vapors is above the lower
flammable limit, repeat the cleaning procedures.
11
13. Painting Instructions 100 YRM 284
Chemical Solution Method
If the tank cannot be cleaned with steam, use the fol-
lowing procedure:
1. Mix a solution of water and trisodium phosphate or
a cleaning compound with an alkali base. Follow
the instructions given by the manufacturer.
WARNING
Compressed air can move particles so that they
cause injury to the user or to other personnel.
Make sure that the path of the compressed air is
away from all personnel. Wear protective goggles
or a face shield to prevent injury to the eyes.
2. Fill tank with cleaning solution. Use compressed air
to mix solution in tank.
3. Drain tank. Flush inside of tank with hot (boiling)
water. Make sure all cleaning compound is re-
moved.
4. Make an inspection of inside of tank. If tank is not
clean, repeat Step 1 through Step 3. Make another
inspection of tank. When making inspections, use
a light that is approved for locations with flammable
vapors.
5. Check tank for flammable vapors using a special
indicator for gas vapors. If the amount of flammable
vapors is above the lower flammable limit, repeat
the cleaning procedures.
ADDITIONAL PREPARATIONS FOR
REPAIR
If nitrogen gas or carbon dioxide gas is available, pre-
pare the tank for welding using these gases. See the
manual Safe Practices For Welding and Cutting Con-
tainers That Have Held Combustibles by the American
Welding Society, A6.0-65. If these gases are not avail-
able, another method using water can be used as fol-
lows:
1. Fill tank with water to just below the point where the
work will be done. Make sure the space above the
level of the water has a vent.
2. Use acceptable welding practices to repair tank.
See the American National Standard "Safety in
Welding and Cutting," ANSI Z 49.1 - 1973.
Painting Instructions
WARNING
Always use solvents and paints in an area with
ventilation. Do not use solvents or paints near
heat, fire, or electrical equipment that can make
sparks. Follow the manufacturer’s instructions
and Cautions.
1. Remove all dirt from surface to be painted. Clean
area to be painted. Use a solvent for painted sur-
faces to remove grease and oil before sanding. Do
not use solvent on new paint. Make sure all oil and
grease is removed.
2. Use sandpaper to remove top surface of paint and
rust from metal. All metal surfaces where paint
is completely removed must be painted. Use a
primer. Apply primer before applying final coat of
paint.
3. Protect all surfaces that will not be painted. See the
list of items in Figure 12.
CAUTION
Do not paint the pads, plastic covers or knobs,
cables, labels, and information plates or controls.
Paint can make some assemblies not operate cor-
rectly.
4. Paint surfaces. Use correct paint from your dealer
for Yale lift trucks. Follow directions on container.
The correct arrangement of colors is shown in the
note in Figure 12.
WARNING
Make sure all labels are installed after painting is
complete. Safety labels are installed on the lift truck
to give information about possible hazards. It is
important that all safety labels are installed on the
lift truck and can be read.
5. Check that all safety labels are installed in correct
locations on lift truck. New labels are available from
your dealer for Yale lift trucks.
12
14. 100 YRM 284 Safety Label Replacement
NOTE: USE COLORS APPROVED BY YALE. DO NOT PAINT THE FOLLOWING ITEMS: PEDAL PADS, LEVER
KNOBS, INSTRUMENTS, STEERING WHEEL, SEAT ASSEMBLY AND SEAT RAILS, INFORMATION CASE AND
COVER, TIRES, MAST CHAINS AND HOSES, ALL LABELS AND INFORMATION PLATES, BATTERY CONNEC-
TOR, PARKING BRAKE HANDLE, KEY SWITCH, CYLINDER RODS, ALL PLASTIC COVERS, AND STEERING
COLUMN COVER.
NOTE: LIGHT AREAS = YELLOW, DARK AREAS = BLACK, AND LIGHT GRAY AREAS = PARCHMENT.
Figure 12. Color Arrangement
Safety Label Replacement
If the labels or information plates are missing or have
damage, they must be replaced. See Figure 13.
WARNING
Labels that have WARNINGS or CAUTIONS must be
replaced if they are damaged. If an upright of a dif-
ferent size or an accessory carriage is installed, the
capacity rating can change. Changes in the kind
of drive tires can change the capacity rating. See
a YALE Dealer for a replacement nameplate. The
nameplate information is a safety item and must be
correct for the equipment and configuration of the
lift truck.
NOTE: The nameplate is installed using rivets. The old
rivets must be removed before installing a new name-
plate.
1. Make sure surface is dry and has no oil or grease.
Do not use solvent on new paint. Clean surface of
old paint using a cleaning solvent.
2. Remove paper from back of label. Do not touch
adhesive surface.
3. Carefully hold label in correct position above sur-
face. The label cannot be moved after it touches
the surface. Put label on surface. Make sure all air
is removed from under label and corners and edges
are tight.
13
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. 620 YRM 294 Brush and Commutator Inspection
General
This section describes disassembly and assembly,
brush installation, inspection, and checks for mal-
functions of DC motors. Inspect the commutator and
brushes every 350 hours of operation. The commu-
tator is the rotating electric connection between the
armature and the electric power supplied by the bat-
tery. Brushes made of carbon compounds slide on
the rotating commutator and are the path for electricity
from the battery to the commutator and the armature.
The maintenance of the commutator and the brushes
is important to the good operation of a DC motor.
Traction motors and hydraulic pump motors are similar
in design. The hydraulic pump motors are smaller
than the traction motors, but the disassembly and
maintenance of these motors are similar. The cooling
fan in the traction motors is fastened to the armature
and can be removed from the armature. The cooling
fan can be removed during disassembly of the traction
motor.
The cooling fan in the hydraulic pump motors can be a
press fit on the armature shaft and is not easily removed
during disassembly of the motor. The armature and
cooling fan must be removed from the drive end of the
motor during disassembly.
The assembly and disassembly of the motor used for
the power steering pump is described in the Steering
System section. This motor is a permanent magnet
motor.
Brush and Commutator Inspection
HYDRAULIC PUMP MOTOR AND
TRACTION MOTOR
NOTE: When inspecting brush conditions and motor
commutator conditions for head damage or abnormal
wear, the battery maintenance and condition should be
eliminated as a cause first. See Industrial Battery
2240 YRM 1.
NOTE: The brushes and commutator can be inspected,
the brushes can be replaced, and Stoning the Commu-
tator can be done with the motor installed in the truck.
NOTE: Inspect the brushes and commutator every 350
hours for best operation and to prevent motor damage.
The hydraulic pump motor normally has more start cy-
cles than other motors, so it can have more wear and
possible damage.
NOTE: The following procedure is for inspecting the
brushes and commutator with the motor installed in the
lift truck. The same inspections can be done with the
motor removed. If the motor is removed, start at Step 3.
1. To rotate the commutator of the traction motor with-
out moving the truck, the drive wheels must be
raised. See Figure 1. Raise drive wheels so com-
mutator of the traction motor can be rotated without
moving lift truck. See How To Raise Drive Wheels
in the Operating Manual or the Periodic Mainte-
nance YRM section for your lift truck.
NOTE: For some models of lift trucks, the battery does
not need to be removed to access the electric motors.
Other models will require the removal of the battery be-
fore gaining access to the electric motors. To remove
the battery, either raise the hood panels or unfasten the
floor plate, depending on which motor needs to be ac-
cessed.
1. ARMATURE
(DRIVE) SHAFT
2. COOLING FAN
3. BRUSH COVER
Figure 1. Traction Motor
1