This service repair manual provides instructions for installing a cylinder head on a 350-A L excavator with a 3306 engine. It is a 16-step process that involves cleaning surfaces, installing gaskets and bolts, tightening bolts in a specific sequence, adjusting valves, and reinstalling related components like manifolds. It also describes removing and installing the spacer plate and water directors in 2 steps each to prepare the cylinder head for installation.
This document provides instructions for installing a cylinder head on a Caterpillar 350-A L excavator engine. The procedure involves:
1. Cleaning and preparing the cylinder head and block mating surfaces.
2. Installing a new cylinder head gasket and positioning the cylinder head on the block.
3. Applying oil to the cylinder head bolts and tightening them in the specified sequence.
4. Installing other components like pushrods, rocker arms, intake and exhaust components.
The instructions provide detailed steps and illustrations to correctly position and secure the cylinder head. Special attention is given to cleaning parts and applying the proper torque to the head bolts.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
This document provides instructions for installing a cylinder head on a Caterpillar 350-A L excavator engine. The procedure involves:
1. Cleaning and preparing the cylinder head and block mating surfaces.
2. Installing a new cylinder head gasket and positioning the cylinder head on the block.
3. Applying oil to the cylinder head bolts and tightening them in the specified sequence.
4. Installing other components like pushrods, rocker arms, intake and exhaust components.
The instructions provide detailed steps and illustrations to correctly position and secure the cylinder head. Special attention is given to cleaning parts and applying the proper torque to the head bolts.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 215 d excavator (prefix 9tf) service repair manual (9tf00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B engine. The disassembly process involves removing various parts like the fuel rack, lifters, camshaft and bearings. The assembly process details installing these parts in reverse order and setting proper clearances and positions. Tools required include retaining ring pliers and a driver group. Precautions are given to keep parts clean and apply oil before assembly.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
Caterpillar cat 385 b l excavator (prefix cls) service repair manual (cls0000...fjjskekmsemm
The document provides assembly instructions for control valves on 385B and 385B L excavators. It involves 25 steps to assemble components like spools, seals, plugs, resolver valves, differential relief valves, and covers. Special tools may be required and parts need to be checked for wear before assembly. Springs and other components must be assembled carefully according to the instructions to avoid injury. Torque specifications are provided for tightening certain parts.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Special steps are provided to determine the correct bearing preload using shims and applying hydraulic pressure.
Caterpillar cat 385 b l excavator (prefix bkf) service repair manual (bkf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to reassembly.
3) Reassembling the components in reverse order, applying lubricants and determining proper bearing preload using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix rcd) service repair manual (rcd00001 ...fjjskekmsemm
The document provides instructions for disassembling and assembling various components of an excavator control valve, including:
1. Disassembling the proportional valve by removing bolts, nuts, and cartridge components.
2. Assembling the attachment, bucket, and boom control valve by installing O-rings, plugs, resolver valves, springs, and actuator groups.
3. Assembling the right travel, left travel, and stick control valve by installing spools, plugs, resolver valves, O-rings, and covers.
Caterpillar cat 385 b excavator (prefix mya) service repair manual (mya00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and gaskets. Corresponding assembly steps are also provided, with notes to check components for wear and reduce temperature before inserting some parts. The goal is to properly disassemble and reassemble the control valve while preventing contamination.
Caterpillar cat 385 b excavator (prefix fdl) service repair manual (fdl00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar cat 385 b excavator (prefix cls) service repair manual (cls00001 ...fjjskekmsemm
The document provides assembly instructions for control valves for attachment, bucket, boom, right travel, left travel, and stick functions on 385B and 385B L excavators. It involves installing seals, spools, resolver valves, solenoids, pistons, actuators, and covers. Proper torque values are specified and safety precautions are provided due to parts being under spring load.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. It provides details on installing bearings and determining the correct number of shims using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix bkx) service repair manual (bkx00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It includes:
1) A list of required tools for the job.
2) Detailed step-by-step instructions for removing over 30 components of the final drive, including gears, shafts, housings, and seals.
3) Procedures for installing new bearings and determining the proper bearing preload during assembly.
Caterpillar cat 385 b excavator (prefix bkf) service repair manual (bkf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and includes pressing bearings into place, determining the correct shim thickness, and installing seals. Precise alignment of parts and cleanliness are emphasized throughout.
Caterpillar cat 374 f l excavator (prefix ebf) service repair manual (ebf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 f excavator (prefix ebf) service repair manual (ebf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
The document provides instructions for removing and installing the engine oil pump on a Caterpillar C7.1 engine. It describes removing the oil pan, suction pipe, brackets, and bolts to detach the pump. Instructions are given to disassemble the pump components if needed. Reinstallation involves cleaning parts, installing gaskets and dowels, and tightening bolts in the specified sequence and torque. Technicians are advised to replace the entire pump assembly if any parts are worn or damaged.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
This document provides instructions for removing and installing fuel injection lines and an automatic timing advance on a 3406 engine for a generator set. The steps include removing nuts and bolts to detach the lines and timing advance, cleaning surfaces, installing new gaskets, and tightening to the specified torques. Disassembly and assembly of the automatic timing advance and fuel transfer pump are also described in detail with accompanying diagrams.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 215 d excavator (prefix 9tf) service repair manual (9tf00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B engine. The disassembly process involves removing various parts like the fuel rack, lifters, camshaft and bearings. The assembly process details installing these parts in reverse order and setting proper clearances and positions. Tools required include retaining ring pliers and a driver group. Precautions are given to keep parts clean and apply oil before assembly.
Caterpillar cat 219 d excavator (prefix 5xg) service repair manual (5xg00001 ...fjskekdmjekm
The document provides instructions for removing and installing various engine components of a 219D Excavator, including the cylinder head, spacer plate, and water directors. It describes removing components like bolts, gaskets and seals in a specific order. Installation is the reverse of removal, applying new gaskets and torquing bolts to the specified values. Precautions are given to keep components clean and contain fluids.
Caterpillar cat 385 b l excavator (prefix cls) service repair manual (cls0000...fjjskekmsemm
The document provides assembly instructions for control valves on 385B and 385B L excavators. It involves 25 steps to assemble components like spools, seals, plugs, resolver valves, differential relief valves, and covers. Special tools may be required and parts need to be checked for wear before assembly. Springs and other components must be assembled carefully according to the instructions to avoid injury. Torque specifications are provided for tightening certain parts.
Caterpillar cat 385 b l excavator (prefix bly) service repair manual (bly0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. Special steps are provided to determine the correct bearing preload using shims and applying hydraulic pressure.
Caterpillar cat 385 b l excavator (prefix bkf) service repair manual (bkf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to reassembly.
3) Reassembling the components in reverse order, applying lubricants and determining proper bearing preload using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix rcd) service repair manual (rcd00001 ...fjjskekmsemm
The document provides instructions for disassembling and assembling various components of an excavator control valve, including:
1. Disassembling the proportional valve by removing bolts, nuts, and cartridge components.
2. Assembling the attachment, bucket, and boom control valve by installing O-rings, plugs, resolver valves, springs, and actuator groups.
3. Assembling the right travel, left travel, and stick control valve by installing spools, plugs, resolver valves, O-rings, and covers.
Caterpillar cat 385 b excavator (prefix mya) service repair manual (mya00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and gaskets. Corresponding assembly steps are also provided, with notes to check components for wear and reduce temperature before inserting some parts. The goal is to properly disassemble and reassemble the control valve while preventing contamination.
Caterpillar cat 385 b excavator (prefix fdl) service repair manual (fdl00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar cat 385 b excavator (prefix cls) service repair manual (cls00001 ...fjjskekmsemm
The document provides assembly instructions for control valves for attachment, bucket, boom, right travel, left travel, and stick functions on 385B and 385B L excavators. It involves installing seals, spools, resolver valves, solenoids, pistons, actuators, and covers. Proper torque values are specified and safety precautions are provided due to parts being under spring load.
Caterpillar cat 385 b excavator (prefix bly) service repair manual (bly00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of 385B and 385B L Excavators.
The disassembly procedure involves removing 27 parts from the final drive housing using various tools. This includes removing gears, shafts, washers, bearings and seals.
The assembly procedure instructs to thoroughly clean all parts, apply anti-seize compound, and install parts in reverse order of disassembly. It provides details on installing bearings and determining the correct number of shims using a hydraulic press and micrometer measurements.
Caterpillar cat 385 b excavator (prefix bkx) service repair manual (bkx00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It includes:
1) A list of required tools for the job.
2) Detailed step-by-step instructions for removing over 30 components of the final drive, including gears, shafts, housings, and seals.
3) Procedures for installing new bearings and determining the proper bearing preload during assembly.
Caterpillar cat 385 b excavator (prefix bkf) service repair manual (bkf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling a final drive on 385B and 385B L excavators. The disassembly process involves removing 27 components from the final drive housing using various tools. The assembly process reverses the disassembly steps and includes pressing bearings into place, determining the correct shim thickness, and installing seals. Precise alignment of parts and cleanliness are emphasized throughout.
Caterpillar cat 374 f l excavator (prefix ebf) service repair manual (ebf0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 f excavator (prefix ebf) service repair manual (ebf00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 374F excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, planetary gears and shafts. The assembly process reverses this, applying anti-seize compound and installing components like bearing cups, pins and housings in the correct order. Safety precautions are provided for using hydraulic cylinders and puller studs during assembly.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including gears, shafts, housings and seals. Photos illustrate each step. Assembly requires applying threadlock to fasteners and bearings, and using shims to set the proper bearing preload when reinstalling the main housing. Proper cleaning and inspection of all parts is emphasized before reassembly.
Caterpillar cat 365 c l excavator (prefix mem) service repair manual (mem0000...fjjskekmsemm
This document provides disassembly and assembly instructions for the final drive on a 365C excavator. It describes how to disassemble the various components of the final drive including removing the ring gear, carrier assemblies, gears, shafts and seals. It then describes the assembly process and includes details on cleaning, applying threadlock, installing bearings and seals, and determining the correct shim thickness. The overall document provides a detailed multi-step process for taking apart and rebuilding the final drive assembly.
Caterpillar cat 365 c l excavator (prefix mcs) service repair manual (mcs0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 365C excavator. It outlines 33 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then outlines 11 steps to reassemble the final drive, which includes determining the correct shim thickness between components and installing seals using specialized tools. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the final drive.
Caterpillar cat 365 c l excavator (prefix elc) service repair manual (elc0000...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process reverses the disassembly with 31 steps, including verifying clearances with feeler gauges and heating components before installation. Tools include retaining ring pliers, link brackets, and threaded rods for lifting heavy parts. Personal protective equipment is recommended due to spring-loaded components.
Caterpillar cat 365 c excavator (prefix mem) service repair manual (mem00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive on a 365C excavator. It lists over 30 steps for disassembly, which include removing the final drive cover, carrier assemblies, gears, shafts, seals and bearings. For assembly, it lists 8 steps such as cleaning parts, installing bearings, seals and housing components, and determining the correct number of shims using a micrometer to measure gear dimensions. The overall document provides detailed technical instructions for taking apart and rebuilding the final drive transmission on this excavator model.
Caterpillar cat 365 c excavator (prefix mcs) service repair manual (mcs00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the final drive of a 365C excavator. It describes in detail how to remove over 30 individual parts, including gears, shafts, housings and seals. Reassembly is outlined in similar detail, with requirements to clean parts thoroughly, apply locking compounds, and properly set bearing preloads using shims. Proper tools are listed to facilitate disassembly and assembly.
Caterpillar cat 365 c excavator (prefix elc) service repair manual (elc00001 ...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor of a 365C excavator. The disassembly process involves 29 steps to remove components like springs, plates, pistons, seals, and bearings. The assembly process reverses the disassembly with 31 steps, including verifying clearances with feeler gauges and heating components before installation. Tools required include retaining ring pliers, link brackets, and threaded rods for lifting. Personal safety warnings are provided throughout.
Caterpillar cat 365 b mh excavator (prefix cty) service repair manual (cty000...fjjskekmsemm
1) The document provides assembly instructions for a final drive on an excavator. It details cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting bearing preload using shims.
2) Carrier assemblies are assembled by installing bearings, thrust washers, and planetary gears, then securing with spring pins.
3) Carrier assemblies are installed in the ring gear and main housing, and components are secured with bolts torqued to specification.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00602759
3304B torque sequence
10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00328807
3306B torque sequence
11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
Illustration 6 g00511911
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
Illustration 7 g00541522
4/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 14. Connect tube (8) to the inlet manifold.
Illustration 8 g00541524
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
Illustration 9 g00541527
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:36:40 UTC+0800 2020
5/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00540847
1/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
Illustration 2 g00540857
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
Illustration 3 g00540895
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
Installation Procedure
2/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
Illustration 4 g00540895
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Illustration 5 g00540857
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Install spacer plate (2) on the cylinder head.
Illustration 6 g00540847
4. Install a new O-ring seal (1). Install new water seals (3). Install new water directors (4) .
5. Check the cylinder liner projection. Refer to Disassembly and Assembly, "Cylinder Liner -
Install".
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:37:36 UTC+0800 2020
4/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00943364
Water Directors - Remove and Install
SMCS - 1115-010
Removal Procedure
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00481082
1/2
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Remove water directors (1) from the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the cylinder head before assembly.
Illustration 2 g00481082
2. Install new water director (1) into the cylinder head. Align the notch in water director (1)
with the "V" mark on the cylinder head.
3. Install water director (1) to a depth of 0.8 ± 0.6 mm (0.031 ± 0.023 inch) below the surface
of the cylinder head.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:38:32 UTC+0800 2020
2/2
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01042782
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00538891
1. Use Tool (A) to remove valve lifter (1), as shown. Put identification marks on the valve
lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
3. Check the diameter of the valve lifters. The diameter of a new valve lifter must be 33.285 ±
0.015 mm (1.3105 ± 0.0005 inch). The diameter of the bore in the cylinder block for a new
valve lifter must be 33.388 ± 0.050 mm (1.3145 ± 0.0020 inch). The maximum permissible
clearance between the valve lifter and the valve lifter bore in the cylinder block must be
0.30 mm (0.012 inch).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Illustration 2 g00538891
2/3
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) with
Tool (A) in the original location in the cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:39:28 UTC+0800 2020
3/3
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01037991
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
B. Remove the timing gear cover. Refer to Disassembly and Assembly, "Front Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00476744
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. The "C" mark on
the crankshaft gear will be aligned with the "C" mark on the camshaft gear.
Illustration 2 g00476743
Note: Put a mark on the teeth of the fuel injection pump drive gear and the idler gear at
location (A). This will help to keep the engine timing correct during the removal and the
installation of the camshaft. Put a mark on the teeth of the idler gear and camshaft gear (2)
at location (B). When the camshaft is installed, the engine timing will be correct when the
mark at location (A) is aligned with the mark at location (B) and the "C" mark on the
crankshaft gear is aligned with the "C" mark on the camshaft gear.
2. Remove the bolts, the lock and washer (1) .
Illustration 3 g00535590
2/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. NOTICE
Do not damage the lobes or the bearings when the camshaft is
removed.
3. Carefully remove camshaft (3) from the engine.
4. If necessary, remove the bolts that hold camshaft drive gear (2) to the camshaft and remove
the gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00535590
1. Put camshaft drive gear (2) in position on the end of camshaft (3). Install the bolts that hold
camshaft drive gear (2) to camshaft (3). Tighten the bolts to a torque of 55 ± 7 N·m (41 ± 5
lb ft).
NOTICE
Do not damage the lobes or the bearings when the camshaft is installed.
3/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 2. Put 8T-2998 Camshaft Lubricant on the camshaft lobes only and put clean engine oil on the
bearing journals.
Note: During the installation of camshaft (3), rotate the camshaft in both directions in order
to prevent binding in the camshaft bearing bores.
3. Carefully install camshaft (3) into the engine.
Illustration 5 g00476743
Illustration 6 g00476744
4. Make sure that the mark on the teeth of the fuel injection pump drive gear and the idler gear
are in alignment at location (A). Make sure that the mark on the teeth of the idler gear and
camshaft gear (2) are in alignment at location (B). Align the "C" marks on the crankshaft
gear and camshaft gear (2). When all of the timing marks are in alignment the engine timing
is correct.
4/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 5. Install washer (1), the lock and the two bolts that hold the camshaft in position in the
engine.
End By:
a. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:40:23 UTC+0800 2020
5/5
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A L EXCAVATOR 9FL
Configuration: 350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02473351
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove
and Install".
C. Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 1 g00478567
1. Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front
bearings and work to the rear bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g00478567
1. Use Tool (A) to install the camshaft bearings in the 3304B and 3306B cylinder block.
Note: The camshaft bearings in the 3304B have pressure lubrication. The intermediate
camshaft bearings and the rear camshaft bearings in the 3306B have splash lubrication.
2. Install the camshaft bearings in the 3304B cylinder block, as follows:
(a) Install the front bearing to a depth of 0.57 ± 0.5 mm (0.022 ± 0.02 inch). Ensure that the
oil holes are in a horizontal position and that the camshaft bearing joint is at the top of the
engine. The camshaft bearing joint can not be more than 15° degrees from vertical in either
direction.
(b) Install the center bearing to a depth of 303.2 ± 0.5 mm (11.94 ± 0.02 inch). Ensure that
the oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder
block.
(c) Install the rear bearing to a depth of 604.9 ± 0.5 mm (23.81 ± 0.02 inch). Ensure that the
oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder block.
Illustration 3 g00478822
1. Install the camshaft bearings in the 3306B cylinder block, as follows:
2. Install front bearing (B) to a depth of 0.5 ± 0.5 mm (.02 ± .02 inch). Ensure that the oil holes
are in a horizontal position and that the camshaft bearing joint is at the top of the engine.
The camshaft bearing joint cannot be more than 15 degrees from the vertical position in
either direction.
3. Install the remainder of the bearings. Install the bearings to the dimensions that are given
from the front face of the cylinder block: (C) 154.0 ± 0.5 mm (6.06 ± .02 inch), (D) 303.2 ±
3/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 0.5 mm (11.94 ± .02 inch), (E) 601.7 ± 0.5 mm (23.69 ± .02 inch) and (F) 903.4 ± 0.5 mm
(35.57 ± .02 inch).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
b. Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate -
Remove and Install".
c. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 22 18:41:19 UTC+0800 2020
4/4
350 & 350 L Excavators 9FL00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2020/10/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...