The document provides instructions for disassembling the travel motor of a 336F XE or 336F LXE excavator. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release spring forces and properly mark parts for reassembly. Tools required include various bolts, pins, adapters, and pullers to dismantle the motor.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat 336 f l excavator (prefix tje) service repair manual (tje0000...fjkskedmme
The document provides instructions for disassembling the travel motor of a 336F excavator. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjjseksxckmdme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices advise wearing protective equipment when removing components under spring pressure.
Caterpillar cat 336 f xe excavator (prefix pfl) service repair manual (pfl000...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Various tools are required including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to watch for released spring forces while disassembling components.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat 336 f l excavator (prefix tje) service repair manual (tje0000...fjkskedmme
The document provides instructions for disassembling the travel motor of a 336F excavator. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided to warn of potential spring forces and ensure protective equipment is worn during disassembly.
Caterpillar cat 336 f excavator (prefix wcf) service repair manual (wcf00001 ...fjkskedmme
The document provides disassembly instructions for a 336F excavator travel motor over 27 steps. It details removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...fjsjekdmmeme
This document provides instructions for disassembling a 336F excavator travel motor. It lists 27 steps to completely disassemble the travel motor. The steps include removing the motor head assembly, springs, seals, plates, pistons, bearings, and other internal components. Precautions are provided to watch for spring forces and contain fluids during disassembly. Special tools are listed that are required to properly disassemble parts like retaining rings and pistons.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjjseksxckmdme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices advise wearing protective equipment when removing components under spring pressure.
Caterpillar cat 336 f xe excavator (prefix pfl) service repair manual (pfl000...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Various tools are required including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to watch for released spring forces while disassembling components.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully during disassembly.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...cfvdssd
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations are provided to identify each part and tooling is specified to aid in removal, like using bolts, pry bars and retaining ring pliers. Safety notices advise wearing protective equipment when removing parts with spring forces.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations are provided to identify each part and tooling is specified to aid in removal, like using bolts, pry bars and retaining ring pliers. Safety notices warn of potential spring forces and ensuring fluids are contained.
Caterpillar Cat 336F XE and 336F LXE Excavator (Prefix PFL) Service Repair Ma...yin9niaojiao
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing the motor head assembly, port plate, springs, pistons, bearing races, seals and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and eyebolts to safely remove parts and release spring forces. The document aims to guide the disassembly process while noting safety precautions for technicians performing the work.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 5rr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
1. Removing and installing the spacer plate, which involves removing seals and gaskets.
2. Removing and installing water directors by removing them from the cylinder head and pressing new ones in at a specified depth.
3. Removing and installing the lifter group using a magnetic tool and checking lifter diameters.
4. Removing and installing the camshaft by aligning timing marks, removing bolts and gears, cleaning parts, and reinstalling with lubricant while rotating to prevent binding.
Caterpillar cat d6 r track type tractor (prefix 5pr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing a spacer plate on a D6R track-type tractor with a 3306 engine. It describes removing the cylinder head, O-rings, seals, and spacer plate. It then details cleaning surfaces, installing new gaskets and seals, and reinstalling the spacer plate and cylinder head. The process also includes checking cylinder liner projection after installation.
Caterpillar cat d6 r track type tractor (prefix 5ln) service repair manual (5...fjjseksxckmdme
This document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines. It describes how to disassemble the governor by removing the fuel ratio control and mounting bolts. Proper cleaning of parts to prevent contamination is emphasized. The assembly procedure explains how to install bearings and other components in the fuel injection pump housing using various tools, and how to set the timing when installing the pump and governor.
Caterpillar cat d6 r track type tractor (prefix 4wr) service repair manual (4...fjjseksxckmdme
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torquing bolts and nuts to specified values after applying thread locking compound.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
More Related Content
Similar to Caterpillar cat 336 f xe excavator (prefix naj) service repair manual (naj00001 and up)
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully during disassembly.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...cfvdssd
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27 step procedure includes removing the motor head assembly, spool assembly, springs, seals, plugs and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and lifting devices. Safety precautions are provided to prevent injury from parts propelled by spring forces during disassembly.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations are provided to identify each part and tooling is specified to aid in removal, like using bolts, pry bars and retaining ring pliers. Safety notices advise wearing protective equipment when removing parts with spring forces.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations are provided to identify each part and tooling is specified to aid in removal, like using bolts, pry bars and retaining ring pliers. Safety notices warn of potential spring forces and ensuring fluids are contained.
Caterpillar Cat 336F XE and 336F LXE Excavator (Prefix PFL) Service Repair Ma...yin9niaojiao
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices remind technicians to contain fluids and release spring forces carefully.
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing the motor head assembly, port plate, springs, pistons, bearing races, seals and other components. Dismantling requires the use of various tools including retaining ring pliers, drivers, bearing pullers and eyebolts to safely remove parts and release spring forces. The document aims to guide the disassembly process while noting safety precautions for technicians performing the work.
Similar to Caterpillar cat 336 f xe excavator (prefix naj) service repair manual (naj00001 and up) (7)
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 5rr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
1. Removing and installing the spacer plate, which involves removing seals and gaskets.
2. Removing and installing water directors by removing them from the cylinder head and pressing new ones in at a specified depth.
3. Removing and installing the lifter group using a magnetic tool and checking lifter diameters.
4. Removing and installing the camshaft by aligning timing marks, removing bolts and gears, cleaning parts, and reinstalling with lubricant while rotating to prevent binding.
Caterpillar cat d6 r track type tractor (prefix 5pr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing a spacer plate on a D6R track-type tractor with a 3306 engine. It describes removing the cylinder head, O-rings, seals, and spacer plate. It then details cleaning surfaces, installing new gaskets and seals, and reinstalling the spacer plate and cylinder head. The process also includes checking cylinder liner projection after installation.
Caterpillar cat d6 r track type tractor (prefix 5ln) service repair manual (5...fjjseksxckmdme
This document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines. It describes how to disassemble the governor by removing the fuel ratio control and mounting bolts. Proper cleaning of parts to prevent contamination is emphasized. The assembly procedure explains how to install bearings and other components in the fuel injection pump housing using various tools, and how to set the timing when installing the pump and governor.
Caterpillar cat d6 r track type tractor (prefix 4wr) service repair manual (4...fjjseksxckmdme
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torquing bolts and nuts to specified values after applying thread locking compound.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides disassembly and assembly instructions for a C18 industrial engine pump drive. It describes in detail how to disassemble and assemble the integral pump drive of a CX38-P892 petroleum transmission. The 19 step disassembly procedure includes removing bolts, gears, bearings, seals and other components. The 23 step assembly procedure describes cleaning parts and installing components in reverse order, paying attention to torque specifications and end play measurements. Tools required include lifting devices, pullers, indicators and other specialized tools.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and step-by-step procedures describing how to remove and install each component, with illustrations showing the parts.
3) Safety and cleaning notes are provided throughout to keep parts clean and avoid damage during disassembly and assembly.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure with 5 steps requiring identification marks for installation.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F XE EXCAVATOR NAJ
Configuration: 336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR6140-04 Publication Date -01/04/2015 Date Updated -21/02/2018
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F XE EXCAVATOR NAJ
Configuration: 336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR6140-04 Publication Date -01/04/2015 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F XE EXCAVATOR NAJ
Configuration: 336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR6140-04 Publication Date -01/04/2015 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336F XE & 336F LXE Excavators NAJ00001-UP (MACHINE) POWERED BY C9.3 ...
2020/7/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...