This is the Highly Detailed factory service repair manual for theLIEBHERR L509-1112 WHEEL LOADER, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.LIEBHERR L509-1112 WHEEL LOADER Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly. Service Repair Manual Covers: General Information Product Description Maintenance Diesel Engine Cooling System Travel Hydraulics Working Hydraulics Steering System Brake System Electrical System Transfer Gear Axles and Cardan Shaft Machine Frame and Ballast Weight Central Lubrication System Coverings and CAB Access Cab, Heating and Air-Conditioning Lift Arms and Quick-Change Device Attachments and Accessories Repair Work and Troubleshooting Options File Format: PDF Compatible: All Versions of Windows & Mac Language: English Requirements: Adobe PDF Reader NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveLIEBHERR L509-1112 WHEEL LOADER Service Repair Workshop Manual. Looking for some other Service Repair Manual,please check: https://www.aservicemanualpdf.com/ Thanks for visiting!

1. Service manual
(20
Wheel loader
(10 points)
L506 - L510, L507S, L509S
L514 Stereo / Tier IIIA
(10
en

2. Address
Address: LIEBHERR-WERK BISCHOFSHOFEN GMBH
Dr. Hans Liebherr – Straße 4
A – 5500 BISCHOFSHOFEN, AUSTRIA
Product identification
Manufacturer: LIEBHERR-WERK BISCHOFSHOFEN GMBH
Product group: Wheel loader
Type: L506 L507 L508 L509 L510 L507S L509S L514
Construction number: 1108 1109 1111 1112 1114 1110 1113 1115
Serial number: 19047 19047 19047 19047 19047 19047 19047 21019
Document identification
Order number: 10471543
Author: LBH / T-DOK department
Document version: 01
Manual number:
Owner:
Service manual
(20
Wheel loader
(10 points)
L506 - L510, L507S, L509S
L514 Stereo / Tier IIIA
(10
en

3. Foreword
Target group This Service Manual has been written for those whose job it is to make sure
that the machines remain operational on a daily basis. This specifically
includes the mechanics and workshop specialists at Liebherr dealers and
Liebherr branch offices.
Contents In the first chapter you will find information about safety regulations as well
as specifications of the special tools needed for maintenance and repair.
Chapter 2 provides an overview of all important technical data for the entire
machine and the individual assemblies.
The following chapter, entitled Maintenance, contains the maintenance and
inspection schedule, inspection and setting logs, lubrication schedules and
filling quantity tables, a description of maintenance procedures and speci-
fications for prescribed lubricants and fuels.
The technical description of the machine in the following chapters is divided
into 15 functional groups. The design, function, and technical data for each
group, component and part are explained.
How to use this manual This manual describes a variety of types and finished forms. In general, this
information applies to the types and serial number groups specified in the
footnotes. One exception is that specific type and serial number data are
indicated at the beginning of each section (e.g. the technical specifications of
the components).
Whenever possible, parts and components are supplemented by indication
of the identification number in the heading.
This manual is available in German, English, French, Spanish, Italian and
Russian.
Working instructions It is imperative that safety regulations be observed with all tasks done on the
machine. You will find information on this in the General Information
chapter.
A complete set of tools in perfect condition is required for work on the
machine, along with any special tools that might be needed. Absolute
cleanliness must be observed with all tasks!
Sealing material such as O-rings and surface seals should be replaced
whenever repairs are carried out.
DVD edition We would particularly like to draw your attention to the fact that this book is
available not only in printed form, but also as an electronic document on
DVD (Lidos).

4. General information 1
Product description 2
Maintenance 3
Diesel engine 4
Cooling system 5
Travel hydraulics 6
Working hydraulics 7
Steering system 8
Brake system 9
Electrical system 10
Transfer gear 11
Axles, drive shafts 12
Machine frame, ballast weight 13
Central lubrication system 14
Covering, cab access 15
Cab, heating, air-conditioning 16
Lift arm, quick-change device 17
Attachments, accessories 18
Repair work, troubleshooting 19
Options 20

5. L506 - 1108 / from 22400 L510 - 1114 / from 22400 1.0-1 o f 2
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
1 General Information
1.0
Chapter contents
1 General Information ............................................................ 1.0-1
1.1 Safety regulations...........................................................................1.0-1
1.1.1 Introduction...........................................................................1.0-1
1.1.2 Overview of the safety regulations .......................................1.0-2
1.2 Special tools for maintenance and repair work...............................1.0-1
1.2.1 Special tools in general ........................................................1.0-1
1.2.2 Special tools for hydraulic cylinders .....................................1.0-1
1.2.3 Special tools for electronics..................................................1.0-2
1.2.4 Special tools for axles...........................................................1.0-2
1.2.5 Special tools for the central lubrication system ....................1.0-3
1.2.6 Special tools for the air conditioning system ........................1.0-3
1.2.7 Special tools for cab windows ..............................................1.0-3

6. Service Manual General Information
Safty regulations
L506 - 1108 / from 22400 L510 - 1114 / from 22400 1.0-1 o f 2
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
1.1 Safety regulations
Working on the machine poses safety risks to the operator, driver or
maintenance engineers. You can prevent risks and accidents by regularly
reading and observing the various safety instructions.
This is especially important for personnel who only occasionally work on the
machine, for example, carrying out rigging or maintenance work. The safety
regulations listed below, if conscientiously followed, will ensure your own
safety and that of others, and will prevent the machine from being damaged.
Whenever tasks which could cause danger to personnel or damage to the
machine are described, the necessary safety precautions are explained in
this manual.
These are indicated by the headings Danger, Warning or Caution.
1.1.1 Introduction
1. The symbols below have the following meanings:
Danger
Risk of personal injury.
Denotes an impending dangerous situation which can lead to serious injury
or death if not avoided.
Note the warning.
Warning
Risk of personal injury.
Denotes a potentially dangerous situation which can lead to serious injury or
death if not avoided.
Note the warning.
Caution
Risk of personal injury.
Denotes a potentially dangerous situation which can lead to slight injury if
not avoided.
Note the warning.
Caution
Risk of damage to the machine.
Denotes actions or circumstances which may result in damage to the machine.
Note the warning.
Note
Useful information
Denotes information on correctly handling the machine and the lubricants
and fuels used.
Observe the instructions.

7. General Information Service Manual
Safety regulations
1.0-2 of 2 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
2. Observance of these instructions does not exempt you from following
any additional rules and guidelines that may apply
The following should also be observed:
– The safety rules in force at the operating site
– Legally enforceable road traffic regulations
– Guidelines issued by trade associations
1.1.2 Overview of the safety regulations
A detailed description of these can be read in the relevant section of the
safety regulations chapter in the operating manual.
The following sections are included in the operating manual:
1 Introduction
2 General safety regulations
3 Proper use
4 Decals on the machine
5 Instructions on preventing crushing injuries and burns
6 Instructions on preventing fires and explosions
7 Safety instructions for start-up
8 Safety precautions during start-up
9 Instructions for safe working
10 Safety instructions for driving on slopes
11 Parking safely
12 Transporting the machine safely
13 Towing the machine safely
14 Measures for ensuring safe maintenance
15 Safety instructions for working on machines with hydro accumulators
16 Safety instructions for welding work on the machine
17 Instructions for working safely on the working attachment
18 Safety instructions for transporting the machine by crane
19 Safe maintenance of hydraulic hoses and hose lines
20 Attachments and accessories
21 Protection against vibrations

8. Service Manual General Information
Special tools for maintenance and repair work
L506 - 1108 / from 22400 L510 - 1114 / from 22400 1.0-1 o f 4
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
1.2 Special tools for maintenance and
repair work
1.2.1 Special tools in general
Description ID no. Use Remarks
Digital second thermometer 7020372 All wheel loaders
For measuring temperature
during adjustments
Anti-freeze and battery tester 7408922 All wheel loaders
For checking the acidity concentration
(battery charging state) and for
checking the anti-freeze
24 volt vacuum pump 7408148 All wheel loaders For avoidance of oil losses
12 to 24 volt transformer 6905469 L506 - L514 For use of the vacuum pump
Filling and testing device
with case
8145359 All wheel loaders For checking the hydro accumulator
Manometer 0 - 40 bar 7361288 All wheel loaders For checking the hydraulic pressure
Manometer 0 - 250 bar 5002932 All wheel loaders For checking the hydraulic pressure
Manometer 0 - 600 bar 5002866 All wheel loaders For checking the hydraulic pressure
Manometer connection 7002436 All wheel loaders Connection for the manometer
High pressure hose 1500 mm 7002475 All wheel loaders High pressure hose for manometer
High pressure hose 4000 mm 7009134 All wheel loaders High pressure hose for manometer
Screw connection M 10 x 1 5005180 All wheel loaders For checking the hydraulic pressure
Draining hose 7005660 All wheel loaders For draining of oil via a drain valve
Drain piece 7402657 All wheel loaders For the draining hose
Safety cap SW 10 7009315 All wheel loaders
For securing the valves on the variable
adjustment motor
Safety cap SW 13 7615515 All wheel loaders For securing the valves on the pumps
Safety cap SW 17 7615589 All wheel loaders For securing the valves on the pumps
Safety cap SW 19 7009317 All wheel loaders For securing the valves on the pumps
Safety cap SW 17 7622068 All wheel loaders
For securing the valves on the
control block
1.2.2 Special tools for hydraulic cylinders
Description ID no. Use Remarks
Assembly sleeve 70 mm 9110556
Steering cylinder L506 -
L510
For fitting the seals
Expansion sleeve 70 mm 9110402
Steering cylinder L506 -
L510
For fitting the seals
Assembly sleeve 90 mm 9227161 Steering cylinder L514 For fitting the seals
Expansion sleeve 90 mm 9227162 Steering cylinder L514 For fitting the seals
Assembly sleeve 80 mm 9227165
Lift cylinder L506, L507
Tilt cylinder L506, L507,
L514 - P
For fitting the seals
Expansion sleeve 80 mm 9227166
Lift cylinder L506, L507
Tilt cylinder L506, L507,
L514 - P
For fitting the seals
Assembly sleeve 100 mm 9998626
Lift cylinder L508 - L510
Tilt cylinder L508 - L510
For fitting the seals
Expansion sleeve 100 mm 9110405
Lift cylinder L508 - L510
Tilt cylinder L508 - L510
For fitting the seals
Assembly sleeve 110 mm 9170509
Lift cylinder L514 - Z
Tilt cylinder L514 - Z
For fitting the seals

9. General Information Service Manual
Special tools for maintenance and repair work
1.0-2 of 4 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
Description ID no. Use Remarks
Expansion sleeve 110 mm 9170511
Lift cylinder L514 - Z
Tilt cylinder L514 - Z
For fitting the seals
Bearing head assembly
spanner 58/8 mm
9237826
Steering cylinder L506 -
L510
For fitting the piston rod bearing
Bearing head assembly
spanner 70/8 mm
9210219
Lift cylinder L506, L507
Tilt cylinder L506, L507
For fitting the piston rod bearing
Bearing head assembly
spanner 80/12 mm
9238020
Lift cylinder L508 - L510
Tilt cylinder L508 - L510
For fitting the piston rod bearing
Special socket 93011858 Quick coupler L506 -L510 For loosening and tightening the sleeve
1.2.3 Special tools for electronics
Description ID no. Use Remarks
Digital multimeter 8502956 All wheel loaders
For measuring voltage, current,
resistance and frequency
Test probe, red 884191214 All wheel loaders For testing DEUTSCH plugs
Test probe, black 884191114 All wheel loaders For testing DEUTSCH plugs
Magnet tester 8145743 All wheel loaders For checking solenoid valves
Stripping and crimping pliers
0.5 – 6.0 mm2 8460263 All wheel loaders For MATE-N-LOK plug connectors
Insertion tool 8145432 All wheel loaders For MATE-N-LOK plug connectors
Piston mounting tool 7366655 All wheel loaders For MATE-N-LOK plug connectors
Crimping pliers 8503647 All wheel loaders For DEUTSCH plug connectors
Wedge extractor tool 7026267 All wheel loaders For DEUTSCH plug connectors
Extraction tool size 12 for pin
and bushing
8145674 All wheel loaders For DEUTSCH plug connectors
Extraction tool size 16 for pin
and bushing
8145673 All wheel loaders For DEUTSCH plug connectors
Extraction tool size 20 for pin
and bushing
8503630 All wheel loaders For DEUTSCH plug connectors
EMT data cable 9067426 L506 - L514
For communicating with the control
electronics
Adapter cable RS232<>USB 693190714 All wheel loaders
For communicating with the wheel
loader electronics if there is an error with
the RS232 interface on the notebook.
USB dongle 10333608 L506 - L514
For communicating with the control
electronics
1.2.4 Special tools for axles
Description ID no. Use Remarks
Hand pump 8145835
Front axle L507s,
L509s, L514
For relieving the disc springs and for
testing the tightness of the disc brakes
Feeler gauge 8145535
Front axle
L507s, L509s, L514
For inspecting the wear on the wet disc
brake (T1-2313)
Driver, Øa=150 mm 10220615
Front axle
L506 - L508, L507s
For installing the shaft seal ring in the hub
(T2-2384)
Driver, Øa=205 mm 10220622
Rear axle
L506 - L508, L507s
For installing the shaft seal ring in the hub
(T15-4266)
Driver, Øa=62 mm 10220616
Axles
L506 - L508, L507s
For installing the shaft seal ring in the axle
casing (T3-2387)
Set of 5 spanners 10220617
Axles L506 - L514,
L507s, L509s
For gripping whilst installing or removing
the bevel gear shaft (T5-2386)

10. Service Manual General Information
Special tools for maintenance and repair work
L506 - 1108 / from 22400 L510 - 1114 / from 22400 1.0-3 of 4
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS
Description ID no. Use Remarks
Slotted nut spanner with
3 adapters
10220618
Axles
L506 - L508, L507s
For removing and fitting the bevel gear
shaft and differential (T6-1332)
Driver, Øa=66 mm 10220621
Rear axle
L506 - L508, L507s
For installing the axle seal ring in the axle
casing (T14-4210)
Driver, Øa=185 mm 10220623
Axles
L509 - L514, L509s
For installing the shaft seal ring in the hub
(T10-3502)
Slotted nut spanner 10220633
Axles
L509 - L514, L509s
For removing and fitting the differential
gear (T13-3333)
Handle for driver 10220624
Axles L506 - L514,
L507s, L509s
Required for holding the driver
Slotted nut spanner
with adapter
10220626
Axles
L509 - L514, L509s
For removing and fitting the bevel gear
shaft (T22-3317/A)
Slip bushing, Øa=33 mm 10220627 Front axle L509s
For installing the 100 % lockout piston
(T29-3543)
Thrust bolt 10220628 Front axle L509s
For tightening the 100 % lockout spring
(T30-2316)
Driver, Øa=62.5 mm 10220631
Front axle
L509 - L514, L509s
For installing the shaft seal ring in the axle
casing (T34-2322)
Driver, Øa=90 mm 10220632
Rear axles
L509 - L514, L509s
For installing the shaft seal ring in the
bearing bushing of the axle (T5-3342)
1.2.5 Special tools for the central lubrication system
Description ID no. Use Remarks
Filling press 10009239 All wheel loaders For quickly filling the
Filling connection 7029283 All wheel loaders Reservoir
Central lubrication BEKA MAX
Data cable + software
10008427 All wheel loaders
For inspecting the
Central lubrication system
Central lubrication Gröneveld
data cable
7624289 All wheel loaders
For inspecting the
Central lubrication system
Central lubrication Gröneveld
plug adapter
7624290 All wheel loaders
For inspecting the
Central lubrication system
1.2.6 Special tools for the air conditioning system
Description ID no. Use Remarks
Vacuum pump 7027552 All wheel loaders
For evacuating the air conditioning
system
4-valve test fitting 7027558 All wheel loaders
For testing, evacuating and filling the air
conditioning system
Filling hose blue 1500 mm 7027553 All wheel loaders For the test fitting
Filling hose yellow 1500 mm 7027554 All wheel loaders For the test fitting
Filling hose red 1500 mm 7027555 All wheel loaders For the test fitting
Car coupling 253a 7027556 All wheel loaders For the test fitting
Car coupling 254a 7027557 All wheel loaders For the test fitting
1.2.7 Special tools for cab windows
Description ID no. Use Remarks
Complete tool box with
suction pads
10021147 All wheel loaders For installing and removing windows

11. General Information Service Manual
Special tools for maintenance and repair work
1.0-4 of 4 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L506 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright by
MJFCIFSS

12. L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.0-1 o f 1
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
2 Product description
2.0
Chapter contents
2 Product description ............................................................. 2.0-1
2.1 Technical data ................................................................................2.1-1
2.1.1 Complete machine................................................................2.1-1
2.1.2 Diesel engine......................................................................2.1-12
2.1.3 Cooling system...................................................................2.1-18
2.1.4 Travel hydraulics ................................................................2.1-19
2.1.5 Working hydraulics .............................................................2.1-23
2.1.6 Steering system..................................................................2.1-28
2.1.7 Brake system......................................................................2.1-30
2.1.8 Electrical system.................................................................2.1-31
2.1.9 Transfer gear......................................................................2.1-32
2.1.10 Axles and cardan shaft.......................................................2.1-33
2.1.11 Machine frame and ballast weight......................................2.1-38
2.1.12 Automatic central lubrication system..................................2.1-39
2.1.13 Cab, heating and air conditioning.......................................2.1-40
2.1.14 Lift arms and quick-change device.....................................2.1-41
2.1.15 Equipment and accessories ...............................................2.1-43

13. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-1 o f 1
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
2.1 Technical data
2.1.1 Complete machine
Valid for: L506 - 1108 / from 22400
The values stated refer to the standard version of the machine:
– With 365 / 70 R18 tyres
– Tipping loads and weights include all lubricants, full fuel tank, ROPS/
FOPS cab and driver.
Description Value Unit
Bucket capacity as per ISO 7546 0.8 m³
Bucket width 1900 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2550 mm
B Dump height 2872 mm
C Maximum bucket base height 3011 mm
D Maximum bucket pivot point height 3211 mm
E Maximum bucket top height 4040 mm
F Reach at maximum lifting height and
42° tilt-out angle
818 mm
Fmax. Range at 42° tilt-out angle 1517 mm
G Digging depth 80 mm
H Height above cab 2725 mm
I Height above exhaust 2600 mm
J Ground clearance 295 mm

14. Product description Service manual
Technical data
2.1-2 o f 2 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
K Wheel base 2150 mm
L Overall length 5295 mm
Turning radius over bucket outer edge 3690 mm
Lifting force (SAE) 39 kN
Breakout force (SAE) 43 kN
Tipping load when straight 3540 kg
Tipping load articulated at 30° 3231 kg
Angle of articulation (to each side) 30 °
Operating weight 5160 kg
Tractive force 4587 daN
Travel speed in travel range 1, forward
and reverse
0–6 km/h
Travel speed in travel range 2, forward
and reverse
0–20 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L507 - 1109 / from 22400
The values stated refer to the standard version of the machine:
– With 365 / 70 R18 tyres
– Tipping loads and weights include all lubricants, full fuel tank, ROPS/
FOPS cab and driver.

15. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-3 o f 3
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Bucket capacity as per ISO 7546 0.9 m³
Bucket width 2050 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2550 mm
B Dump height 2872 mm
C Maximum bucket base height 3011 mm
D Maximum bucket pivot point height 3211 mm
E Maximum bucket top height 4040 mm
F Reach at maximum lifting height and
42° tilt-out angle
818 mm
Fmax. Range at 42° tilt-out angle 1517 mm
G Digging depth 80 mm
H Height above cab 2725 mm
I Height above exhaust 2600 mm
J Ground clearance 295 mm
K Wheel base 2150 mm
L Overall length 5295 mm
Turning radius over bucket outer edge 3690 mm
Lifting force (SAE) 44 kN
Breakout force (SAE) 48 kN
Tipping load when straight 3836 kg
Tipping load articulated at 30° 3501 kg
Angle of articulation (to each side) 30 °
Operating weight 5240 kg
Tractive force 4593 daN
Travel speed in travel range 1, forward
and reverse
0–6 km/h
Travel speed in travel range 2, forward
and reverse
0–20 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L508 - 1111 / from 22400
The values stated refer to the standard version of the machine:
– With 405 / 70 R18 tyres
– Tipping loads and weights include all lubricants, full fuel tank, ROPS/
FOPS cab and driver.

16. Product description Service manual
Technical data
2.1-4 o f 4 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Bucket capacity as per ISO 7546 1.0 m³
Bucket width 2100 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2555 mm
B Dump height 2896 mm
C Maximum bucket base height 3035 mm
D Maximum bucket pivot point height 3235 mm
E Maximum bucket top height 4115 mm
F Reach at maximum lifting height and
42° tilt-out angle
817 mm
Fmax range at 42° tilt-out angle 1515 mm
G Digging depth 56 mm
H Height above cab 2749 mm
I Height above exhaust 2624 mm
J Ground clearance 319 mm
K Wheel base 2150 mm
L Overall length 5371 mm
Turning radius over bucket outer edge 3820 mm
Lifting force (SAE) 48 kN
Breakout force (SAE) 49 kN
Tipping load when straight 4190 kg
Tipping load articulated at 30° 3824 kg
Angle of articulation (to each side) 30 °

17. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-5 o f 5
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Operating weight 5480 kg
Tractive force 4364 daN
Travel speed in travel range 1, forward
and reverse
0–6 km/h
Travel speed in travel range 2, forward
and reverse
0–20 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L509 - 1112 / from 22400
The values stated refer to the standard version of the machine:
– With 405 / 70 R18 tyres
– Tipping loads and weights include all lubricants, full fuel tank, ROPS/
FOPS cab and driver.
Description Value Unit
Bucket capacity as per ISO 7546 1.1 m³
Bucket width 2200 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2641 mm
B Dump height 3000 mm
C Maximum bucket base height 3139 mm
D Maximum bucket pivot point height 3339 mm
E Maximum bucket top height 4235 mm
F Reach at maximum lifting height and
42° tilt-out angle
909 mm

18. Product description Service manual
Technical data
2.1-6 o f 6 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Fmax. Range at 42° tilt-out angle 1640 mm
G Digging depth 95 mm
H Height above cab 2750 mm
I Height above exhaust 2625 mm
J Ground clearance 335 mm
K Wheel base 2300 mm
L Overall length 5760 mm
Turning radius over bucket outer edge 4150 mm
Lifting force (SAE) 54 kN
Breakout force (SAE) 55 kN
Tipping load when straight 4645 kg
Tipping load articulated at 30° 4225 kg
Angle of articulation (to each side) 30 °
Operating weight 6080 kg
Tractive force 5592 daN
Travel speed in travel range 1, forward
and reverse
0–6 km/h
Travel speed in travel range 2, forward
and reverse
0–20 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L510 - 1114 / from 22400
The values stated refer to the standard version of the machine:
– With 405 / 70 R20 tyres
– Tipping loads and weights include all lubricants, full fuel tank, ROPS/
FOPS cab and driver.

19. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-7 o f 7
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Bucket capacity as per ISO 7546 1.2 m³
Bucket width 2330 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2676 mm
B Dump height 3035 mm
C Maximum bucket base height 3174 mm
D Maximum bucket pivot point height 3374 mm
E Maximum bucket top height 4270 mm
F Reach at maximum lifting height and
42° tilt-out angle
874 mm
Fmax range at 42° tilt-out angle 1605 mm
G Digging depth 60 mm
H Height above cab 2785 mm
I Height above exhaust 2660 mm
J Ground clearance 370 mm
K Wheel base 2300 mm
L Overall length 5760 mm
Turning radius over bucket outer edge 4190 mm
Lifting force (SAE) 60 kN
Breakout force (SAE) 62 kN
Tipping load when straight 5036 kg
Tipping load articulated at 30° 4581 kg
Angle of articulation (to each side) 30 °
Operating weight 6250 kg

20. Product description Service manual
Technical data
2.1-8 o f 8 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Tractive force 5002 daN
Travel speed in travel range 1, forward
and reverse
0– 6 km/h
Travel speed in travel range 2, forward
and reverse
0–20 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L507 - 1110 / from 22400
The values stated refer to the standard version of the machine:
– With 365 / 70 R18 tyres
– Including all lubricants
– With a full tank
– With ROPS/FOPS cab and driver
Description Value Unit
Bucket capacity as per ISO 7546 0.9 m³
Bucket width 2050 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2550 mm
B Dump height 2872 mm
C Maximum bucket base height 3011 mm
D Maximum bucket pivot point height 3211 mm
E Maximum bucket top height 4040 mm

21. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-9 o f 9
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
F Reach at maximum lifting height and
42° tilt-out angle
818 mm
Fmax. Range at 42° tilt-out angle 1517 mm
G Digging depth 80 mm
H Height above cab 2725 mm
I Height above exhaust 2600 mm
J Ground clearance 295 mm
K Wheel base 2150 mm
L Overall length 5295 mm
Turning radius over bucket outer edge 3690 mm
Lifting force (SAE) 44 kN
Breakout force (SAE) 48 kN
Tipping load when straight 3836 kg
Tipping load articulated at 30° 3501 kg
Angle of articulation (to each side) 30 °
Operating weight 5240 kg
Tractive force 46.03 kN
Travel speed in travel range 1,
forward and reverse
0–7 km/h
Travel speed in travel range 2,
forward and reverse
0–30 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L509 - 1113 / from 22400
The values stated refer to the standard version of the machine:
– With 405 / 70 R18 tyres
– Including all lubricants
– With a full tank
– With ROPS/FOPS cab and driver

22. Product description Service manual
Technical data
2.1-10 o f 1 0 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Bucket capacity as per ISO 7546 1.1 m³
Bucket width 2200 mm
Specific material weight 1.8 t/m³
A Dump height at maximum lifting height
and 45° tilt-out angle
2641 mm
B Dump height 3000 mm
C Maximum bucket base height 3139 mm
D Maximum bucket pivot point height 3339 mm
E Maximum bucket top height 4235 mm
F Reach at maximum lifting height and
42° tilt-out angle
909 mm
Fmax. Range at 42° tilt-out angle 1640 mm
G Digging depth 95 mm
H Height above cab 2750 mm
I Height above exhaust 2625 mm
J Ground clearance 335 mm
K Wheel base 2300 mm
L Overall length 5760 mm
Turning radius over bucket outer edge 4150 mm
Lifting force (SAE) 54 kN
Breakout force (SAE) 55 kN
Tipping load when straight 4645 kg
Tipping load articulated at 30° 4225 kg
Angle of articulation (to each side) 30 °
Operating weight 6080 kg

23. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-11 o f 1 1
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Tractive force 55.9 kN
Travel speed in travel range 1,
forward and reverse
0–7 km/h
Travel speed in travel range 2,
forward and reverse
0–30 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 dB (A)
Valid for: L514 - 1115 / from 21019
The values stated refer to the standard version of the machine:
– With 17.5 R25 tyres
– Including all lubricants
– With a full tank
– With ROPS/FOPS cab and driver
Description Value Value Unit
Kinematic version Z P
Bucket capacity as per ISO 7546 1.5 1.4 m³
Bucket width 2400 2400 mm
Specific material weight 1.8 1.8 t/m³
A Dump height at maximum lifting height
and maximum tilt-out angle
2855 2985 mm
B Dump height 3260 3430 mm
C Maximum bucket base height 3440 3610 mm
D Maximum bucket pivot point height 3675 3860 mm
E Maximum bucket top height 4550 4840 mm
F Reach at maximum lifting height and
maximum tilt-out angle
830 785 mm
G Digging depth 53 35 mm
H Height above cab 3025 3025 mm
I Height above exhaust 2890 2890 mm
J Ground clearance 385 385 mm

24. Product description Service manual
Technical data
2.1-12 o f 1 2 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Value Unit
Kinematic version Z P
K Wheel base 2600 2600 mm
L Overall length 6135 6330 mm
Turning radius over bucket outer edge 4510 4610 mm
Lifting force (SAE) 88 83 kN
Breakout force (SAE) 77 77 kN
Tipping load when straight 6200 5385 kg
Articulated tipping load 5680 4920 kg
Angle of articulation (to each side) 30 30 °
Operating weight 8350 8520 kg
Tractive force 58.3 58.3 kN
Travel speed in travel range 1,
forward and reverse
0–8 0–8 km/h
Travel speed in travel range 2,
forward and reverse
0 –30 0–30 km/h
Sound pressure level in cab – LpA
according to ISO 6396
70 70 dB (A)
2.1.2 Diesel engine
Deutz TD 2009 diesel engine
Valid for: L506 - 1108 / from 22400;
Description Value Unit
Engine model Deutz
TD 2009 L04
Number of cylinders 4 pc.
Combustion method Four-stroke,
direct injection
Capacity 2289 Litres
Rated power as per ISO 9249 46/63 kW/hp
Rated speed 2600 rpm
Maximum torque at 1600 rpm 200 Nm
Lower idle speed 950
50
rpm
Upper idle speed 2800
50
rpm
Cylinder bore 90 mm
Stroke 90 mm
Compression ratio 18:1
Combustion pressure 25–30 bar
Injection nozzle operating pressure 250 bar
Firing order 1-3-4-2
Inlet and outlet valve play Hydraulic setting
Injection pump Injection pump
distributor
Controller Mechanical
Turbocharger Limited-pressure
wastegate

25. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-13 o f 1 3
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Longitudinal/traverse inclinability 30 °
Starter power consumption 2.0 kW
Alternator voltage output 12 V
Alternator current output 80 A
Control thermostat opening temperature 86 °C
Minimum pressure in cooling system
behind pump
0.7 bar
Auxiliary power take-off transmission 1.0 i
Weight 220 kg
Emission thresholds comply with EU directive 97/68 EC
Stage IIIA
Deutz TD 2009 diesel engine
Valid for: L507 - 1109 / from 22400; L507 - 1110 / from 22400; L508 - 1111 / from 22400;
Description Value Unit
Engine model Deutz
TD 2009 L04
Number of cylinders 4 pc.
Combustion method Four-stroke, direct
injection
Capacity 2289 cm³
Rated power as per ISO 9249 48/65 kW/hp
Rated speed 2800 rpm
Maximum torque at 1600 rpm 200 Nm
Lower idle speed 950
50
rpm
Upper idle speed 3070
50
rpm
Cylinder bore 90 mm
Stroke 90 mm
Compression ratio 18:1
Combustion pressure 25–30 bar
Injection nozzle operating pressure 250 bar
Firing order 1-3-4-2
Inlet and outlet valve play Hydraulic setting
Injection pump Injection pump
distributor
Controller Mechanical
Turbocharger Limited-pressure
wastegate
Longitudinal/traverse inclinability 30 °
Starter power consumption 2.0 kW
Alternator voltage output 12 V
Alternator current output 80 A
Control thermostat opening temperature 86 °C
Minimum pressure in cooling system
behind pump
0.7 bar

26. Product description Service manual
Technical data
2.1-14 o f 1 4 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Auxiliary power take-off transmission 1.0 i
Weight 220 kg
Emission thresholds comply with EU directive 97/68 EC Stage IIIA
Deutz TD 2011 diesel engine
Valid for: L509 - 1112 / from 22400; L509 - 1113 / from 22400; L510 - 1114 / from 22400;
Description Value Unit
Engine model Deutz
TD 2011 L04W
Number of cylinders 4 pc.
Combustion method Four-stroke,
direct injection
Capacity 3619 cm³
Rated power as per ISO 9249 60/82 kW/hp
Rated speed 2600 rpm
Maximum torque at 1600 rpm 257 Nm
Lower idle speed 950
50
rpm
Upper idle speed 2800
50
rpm
Cylinder bore 96 mm
Stroke 125 mm
Compression ratio 18:1
Combustion pressure 22–30 bar
Injection nozzle operating pressure 170 bar
Firing order 1-3-4-2
Inlet and outlet valve play 0.3 / 0.5
Injection pump PLD
Controller Mechanical
Turbocharger Limited-pressure
wastegate
Longitudinal/traverse inclinability 30 °
Starter power consumption 2.3 kW
Alternator voltage output 14 V
Alternator current output 95 A
Control thermostat opening temperature 88–92 °C
Minimum pressure in cooling system
behind pump
0.7 bar
Auxiliary power take-off transmission 1.0 i
Weight 268 kg
Emission thresholds comply with EU directive 97/68 EC
Stage IIIA

27. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-15 o f 1 5
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
John Deere CD4045 diesel engine
Valid for: L514 - 1115 / from 21019;
Description Value Unit
Engine model John Deere
CD4045HF288
Type 4-cylinder inline
Combustion method Four-stroke
direct injection
Capacity 4525 cm³
Rated power as per ISO 9249 72 / 97 kW / hp
Rated speed 2400 rpm
Maximum torque at 1680 rpm 395 Nm
Lower idle speed 850 10
rpm
Upper idle speed 2520
20
rpm
Cylinder bore 106 mm
Stroke 127 mm
Compression ratio 19:1
Combustion pressure 24–28 bar
Injection nozzle operating pressure 245 bar
Firing order 1 3 4 2
Inlet and outlet valve play 0.35/0.45
Injection pump Common rail
Controller Electronic
Turbocharger Constant
Longitudinal/traverse inclinability 30 °
Starter power consumption 4.8 kW
Alternator voltage output 12 V
Alternator current output 65 A
Control thermostat opening temperature 82.2 °C
Minimum pressure in cooling system
behind pump
0.14 bar
Auxiliary power take-off transmission 0.968 i
Weight 444 kg
Emission thresholds comply with EU directive 97/68 EC Stage III
Fuel system
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L508 - 1111 / from 22400;
L509 - 1112 / from 22400; L510 - 1114 / from 22400;
L507 - 1110 / from 22400; L509 - 1113 / from 22400;
Description Value Unit
Tank capacity, FULL 80 l
Tank capacity, RESERVE 20 l

28. Product description Service manual
Technical data
2.1-16 o f 1 6 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Valid for: L514 - 1115 / from 21019
Description Value Unit
Tank capacity, FULL 160 l
Tank capacity, RESERVE 30 l
Fuel pre-filter
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L508 - 1111 / from 22400;
L507 - 1110 / from 22400;
Description Value Unit
Type In-line filter -
Filtration grade 700 µ
Valid for: L509 - 1112 / from 22400; L509 - 1113 / from 22400; L510 - 1114 / from 22400;
Description Value Unit
Type Strainer insert -
Filtration grade Coarse strainer µ
Valid for: L514 - 1115 / from 21019
Description Value Unit
Type Replaceable
cartridge
-
Filtration grade 30 µ
Fuel fine filter
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L507 - 1110 / from 22400;
L508 - 1111 / from 22400;
Description Value Unit
Type Replaceable
cartridge
-
Filtration grade 5 µ
Valid for: L509 - 1112 / from 22400; L509 - 1113 / from 22400; L510 - 1114 / from 22400;
Description Value Unit
Type Replaceable
cartridge
-
Filtration grade 5 µ
Valid for: L514 - 1115 / from 22400;
Description Value Unit
Type Replaceable
cartridge
-
Filtration grade 5 µ

29. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-17 o f 1 7
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Pre-glow system
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L508 - 1111 / from 22400;
L509 - 1112 / from 22400; L510 - 1114 / from 22400;
L507 - 1110 / from 22400; L509 - 1113 / from 22400;
Description Value Unit
Power consumption per plug 20 8
Amp
L514 intake air pre-heater
Valid for: L514 - 1115 / from 21019
Description Value Unit
Heating flange current consumption 120
20
Amp
Vacuum switch
Description Value Unit
Air filter contamination vacuum switch
activation point
50 mbar
Coupling torsion damper
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L507 - 1110 / from 22400;
L508 - 1111 / from 22400;
Description Value Unit
Type CF-KE-093-6.5-
65603
-
Tightening torque for elastic element
fixing screws (6 x)
23 Nm
Valid for: L509 - 1112 / from 22400; L509 - 1113 / from 22400; L510 - 1114 / from 22400;
Description Value Unit
Type CF-KE-093- 6.5-
65921
-
Tightening torque for elastic element fixing
screws (6 x)
23 Nm
Valid for: L514 - 1115 / from 22400;
Description Value Unit
Type BOWEX 65 - 10" -
Tightening torque for elastic element fixing
screws (8 x)
40 Nm
Tightening torque for coupling star fixing
screws (2 x)
45
+5
Nm

30. Product description Service manual
Technical data
2.1-18 o f 1 8 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
2.1.3 Cooling system
Cooling system
Description Value Unit
Fan speed, depending on engine speed
and temperature
580 – 3100 rpm
Operating pressure at 1100 mA
and fan speed
Coolant up to 87°C
Hydraulic oil up to 57°C
14
±5
580 ±50
bar
rpm
Operating pressure at nominal current
L506, L507, L508
130
±10
bar
Operating pressure at nominal current
L509, L510
130
±10
bar
Operating pressure at nominal current
L514
130 ±10
bar
Proportional pressure relief valve
resistance at 20°C
4.8
Pressure relief valve 210 ±10
bar
Fan gear pump
Valid for: L506 - 1108 / from 22400; L509 - 1112 / from 22400; L510 - 1114 / from 22400;
L509 - 1113 / from 22400;
Description Value Unit
Capacity 9.6 cm³
Flow rate (at rated speed) 25.0 l/min
Valid for: L507 - 1109 / from 22400; L508 - 1111 / from 22400; L507 - 1110 / from 22400;
Description Value Unit
Capacity 9.6 cm³
Flow rate (at rated speed) 26.9 l/min
Valid for: L514 - 1115 / from 22400;
Description Value Unit
Capacity 11.5 cm³
Flow rate (at rated speed) 27.6 l/min
Fan gear motor
Description Value Unit
Displacement 8.3 cm³
Max. pressure 210 bar
Temperature sensors
Description Value Unit
Measuring range -30 to +130 °C
Resistance at 20°C 1112

31. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-19 o f 1 9
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
2.1.4 Travel hydraulics
Variable displacement pump L506 - L510
Valid for: L506 - 1108 / from 22400;
Description Value Unit
Type A4VG 40 DA
Maximum capacity 40 cm³
Flow rate at rated speed 104 l/min
Maximum swivel angel (both sides) 20 °
Speed (at rated speed) 2600 rpm
Power 39.8 kW
Replenishing pump capacity 8.6 cm³
Replenishing pump flow rate (at rated
speed)
22.3 l/min
Inlet restrictor 1.8 mm
Swivel restrictor 0.8 mm
Travel direction solenoid current
consumption
2.5 A
Travel direction solenoid resistance 5 ohms
Replenishing pressure at upper idling speed 30 ±2
bar
Start of regulation 1100
±50
rpm
Pump output at 400 bar 2300 ±100
rpm
Pressure relief and replenishing valves 460
±10
bar
Pressure cut-off 430
±5
bar
Weight 31 kg
Valid for: L507 - 1109 / from 22400; L508 - 1111 / from 22400;
Description Value Unit
Control type A4VG 40 DA
Maximum capacity 40 cm³
Flow rate at rated speed 112 l/min
Maximum swivel angel (both sides) 20 °
Speed (at rated speed) 2800 rpm
Power 42.9 kW
Replenishing pump capacity 8.6 cm³
Replenishing pump flow rate
(at rated speed)
24.1 l/min
Inlet restrictor 1.8 mm
Swivel restrictor 0.8 mm
Travel direction solenoid current
consumption
2.5 A
Travel direction solenoid resistance 5 ohms
Replenishing pressure at upper
idling speed
30 ±2
bar
Start of regulation 1100
±50
rpm

32. Product description Service manual
Technical data
2.1-20 o f 2 0 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Pump output at 400 bar 2300 ±100
rpm
Pressure relief and replenishing valves 460
±10
bar
Pressure cut-off 430
±5
bar
Weight 31 kg
Valid for: L509 - 1112 / from 22400; L510 - 1114 / from 22400;
L507 - 1110 / from 22400; L509 - 1113 / from 22400;
Description Value Unit
Type A4VG 56 DA
Maximum capacity 56 cm³
Flow rate at rated speed 145 l/min
Maximum swivel angel (both sides) 20 °
Speed (at rated speed) 2600 rpm
Power L507s 41.1 kW
Power L509, L509s 51.9 kW
Power L510 55.6 kW
Replenishing pump capacity 11.6 cm³
Replenishing pump flow rate
(at rated speed)
30.1 l/min
Inlet restrictor 1.8 mm
Swivel restrictor 1.0 mm
Travel direction solenoid current
consumption
2.5 A
Travel direction solenoid resistance 5 ohms
Replenishing pressure at upper idling speed 30
2
bar
Start of regulation 1100
±50
rpm
Pump output at 400 bar 2300
±100
rpm
Pressure relief and replenishing valves 490
±10
bar
Pressure cut-off 460
±5
bar
Weight 38 kg
Variable displacement pump L514
Valid for: L514 - 1115 / from 21019;
Description Value Unit
Control type DA
Maximum capacity 90 cm³
Flow rate at rated speed 216 l/min
Maximum swivel angel (both sides) 20 °
Speed (at rated speed) 2400 rpm
Power 68.4 kW
Replenishing pump capacity 19 cm³
Replenishing pump flow rate
(at rated speed)
45.6 l/min
Inlet restrictor 1.8 mm

33. Service manual Product description
Technical data
L506 - 1108 / from 22400 L510 - 1114 / from 22400 2.1-21 o f 2 1
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Swivel restrictor 1.0 mm
Travel direction solenoid current
consumption
2.5 A
Travel direction solenoid resistance 5 ohms
Replenishing pressure at upper
idling speed
32
±2
bar
Start of regulation 1050
±50
rpm
Pump output at 380 bar 1950 ±100
rpm
Pressure relief and replenishing valves 490
±10
bar
Pressure cut-off 460
±5
bar
Weight 60 kg
Variable displacement motor
Valid for: L506 - 1108 / from 22400; L507 - 1109 / from 22400; L508 - 1111 / from 22400;
Description Value Unit
Type A6VM 80 DA
Maximum displacement 80 cm³
Minimum displacement 19.2 cm³
Maximum swivel angel 25 °
Minimum swivel angle 5.8 °
Maximum speed 5230 rpm
Torque ( p 400 bar) 509 Nm
Swivel restrictor (size) 0.30 mm
Regulating piston surface ratio 8:100
Maximum discharge valve capacity 5.0 l
Discharge valve orifice diameter 1.4 mm
Solenoid valve current consumption
travel direction + travel range 1
2.5 A
Solenoid valve resistance
travel direction + travel range 1
5 ohms
Control range while driving 230
±10
bar
Weight 34 kg
Valid for: L509 - 1112 / from 22400; L510 - 1114 / from 22400;
Description Value Unit
Type A6VM 107 DA
Maximum displacement 107 cm³
Minimum displacement 32.3 cm³
Maximum swivel angel 25 °
Minimum swivel angle 7.3 °
Maximum speed 4480 rpm
Torque ( p 400 bar) 681 Nm
Swivel restrictor (size) 0.45 mm
Regulating piston surface ratio 8 :100

34. Product description Service manual
Technical data
2.1-22 o f 2 2 L506 - 1108 / from 22400 L510 - 1114 / from 22400
L507 - 1109 / from 22400 L507 - 1110 / from 22400
L508 - 1111 / from 22400 L509 - 1113 / from 22400
L509 - 1112 / from 22400 L514 - 1115 / from 21019
copyright of
MJFCIFSS
Description Value Unit
Maximum discharge valve capacity 8 l
Discharge valve orifice diameter 1.8 mm
Solenoid valve current consumption
travel direction + travel range 1
2.5 A
Solenoid valve resistance
travel direction + travel range 1
5 ohms
Control range while driving L509 215
±10
bar
Control range while driving L510 230
±10
bar
Weight 47 kg
Valid for: L507 - 1110 / from 22400; L509 - 1113 / from 22400;
Description Value Unit
Control type A6VM 140 DA
Maximum displacement 140 cm³
Minimum displacement 31.3 cm³
Maximum swivel angel 25 °
Minimum swivel angle 5.4 °
Maximum speed 4635 rpm
Torque ( p 400 bar) 891 Nm
Swivel restrictor (size) 0.55 mm
Regulating piston surface ratio 8:100
Maximum discharge valve capacity 10.0 l
Discharge valve orifice diameter 2.0 mm
Solenoid valve current consumption
travel direction + travel range 1
2.5 A
Solenoid valve resistance
travel direction + travel range 1
5 ohms
Control range while driving L507 170
±10
bar
Control range while driving L509 215
±10
bar
Weight 60 kg
Valid for: L514 - 1115 / from 21019;
Description Value Unit
Control type A6VM 200 DA
Maximum displacement 200 cm³
Minimum displacement 53.7 cm³
Maximum swivel angel 25 °
Minimum swivel angle 6.5 °
Maximum speed 4005 rpm
Torque ( p 400 bar) 1273 Nm
Swivel restrictor (size) 0.4 mm
Regulating piston surface ratio 8:100
Maximum discharge valve capacity 14 l
Discharge valve orifice diameter 2.4 mm

35. Thank you very much
for your reading.
Please Click Here
Then Get More
Information.