This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor in a specific order. The assembly process reverses the disassembly steps and provides additional details like applying threadlocker and lubricating components. Tools required include various pullers, pliers, and presses. Precise alignment of parts is important and marks should be made during disassembly for reassembly reference.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 parts from the travel motor in 27 steps using various tools. The assembly process reverses the disassembly steps and involves installing the parts back onto the travel motor in the correct order and orientation using lubricants and following safety precautions for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 parts from the travel motor in 27 steps using various tools. The assembly process reverses the disassembly steps and involves installing the parts back onto the travel motor in the correct order and orientation using lubricants and following safety precautions for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkskmmdmd1
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section then lists the 28 steps to reinstall each part in reverse order, noting the proper lubrication and torque specifications. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
More Related Content
Similar to Caterpillar Cat 336E Excavator (Prefix T3Z) Service Repair Manual (T3Z00001 and up).pdf
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkskmmdmd1
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section then lists the 28 steps to reinstall each part in reverse order, noting the proper lubrication and torque specifications. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
Similar to Caterpillar Cat 336E Excavator (Prefix T3Z) Service Repair Manual (T3Z00001 and up).pdf (20)
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 1 23:51:08 UTC+0800 2020
10/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 1 23:52:04 UTC+0800 2020
5/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...