This document provides the disassembly and assembly procedures for a travel motor on excavator models 336E and 336E L. The summary is as follows:
1) The travel motor must be removed from the excavator and various internal components must be disassembled using specialized tools, including removing the head, springs, brake components, and rotating assembly.
2) Individual parts like seals, bearings, and plates are then removed from the housing and other components.
3) Reassembly follows the reverse order, with components being cleaned, inspected, and lubricated before refitting into place using the specialized tools. Precise alignment of parts is important for correct assembly.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Proper torque values and safety precautions are also provided.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components such as gears, seals, springs, and housings. The assembly procedure describes 22 steps and requires various tools to reinstall the components in reverse order. Precautions are provided for releasing spring forces and proper torque specifications.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...f8sejdkdmdijd
This document provides instructions for removing and installing the unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, cutting threads in the unit injector sleeve using specialized tools, and pulling the sleeve out. Installation requires cleaning parts, applying seals and retaining compound, and hammering the sleeve back in. Reinstallation of the hydraulic pump involves connecting tubes and hoses, and securing it with bolts.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools needed are listed. Precautions are given for working with spring loaded parts to prevent injury.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold.
More Related Content
Similar to Caterpillar Cat 336E Excavator (Prefix CMR) Service Repair Manual (CMR00001 and up).pdf
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
Similar to Caterpillar Cat 336E Excavator (Prefix CMR) Service Repair Manual (CMR00001 and up).pdf (6)
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process which includes draining coolant, removing the oil filter and bolts, and removing the base and cooler. The 3 step installation process describes reinstalling the gasket, base, and bolts before refilling the cooling system.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f8sejdkdmdijd
The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, providing notes on cleanliness and replacing seals, O-rings, and other components. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It outlines the necessary tools and safety precautions before describing the 4 step removal process and 4 step installation process. Separate sections also provide instructions for disassembling, assembling, removing and installing the engine oil pump.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove all components of the travel motor. Key steps include using tools to remove the head, brake piston, rotating group, seals and other parts. The assembly procedure reverses the disassembly process in 30 steps and provides notes on cleaning, lubricating and installing parts in their original locations.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Proper torque values and safety precautions are also provided.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual (JRX00001...f8sejdkdmdijd
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The disassembly procedure involves 25 steps to remove components such as gears, seals, springs, and housings. The assembly procedure describes 22 steps and requires various tools to reinstall the components in reverse order. Precautions are provided for releasing spring forces and proper torque specifications.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...f8sejdkdmdijd
This document provides instructions for removing and installing the unit injector sleeve and unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves draining coolant, cutting threads in the unit injector sleeve using specialized tools, and pulling the sleeve out. Installation requires cleaning parts, applying seals and retaining compound, and hammering the sleeve back in. Reinstallation of the hydraulic pump involves connecting tubes and hoses, and securing it with bolts.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. It notes to mark parts locations and clean components. Reassembly follows the reverse order, noting to reinstall parts in their original locations and orientations. Proper cleaning is important to prevent contaminating the hydraulic system.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It details 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Proper cleaning and lubrication of parts is emphasized before assembly. Tools needed are listed. Precautions are given for working with spring loaded parts to prevent injury.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8sejdkdmdijd
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D2 L Excavator (Prefix LAH) Service Repair Manual (LAH0000...f8sejdkdmdijd
1) The document provides disassembly instructions for a travel motor on an excavator model 336D2 L.
2) It describes 27 steps to disassemble the various components of the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, springs and seals.
3) Precautions are provided to watch for spring forces and ensure components are marked for correct reassembly.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...f8sejdkdmdijd
The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, springs and installing them in reverse order. Precautions are outlined for spring loaded parts that could cause injury. Tools required are listed in tables at the beginning and end.
Caterpillar Cat 336E L Excavator (Prefix CMR) Service Repair Manual (CMR00001...f8sejdkdmdijd
1) The document provides instructions for disassembling and assembling a 336E excavator travel motor.
2) It lists 27 steps for disassembly, including removing the head, port plate, springs, brake piston, plates and discs, rotating assembly, and seals.
3) It also lists 28 steps for assembly, including installing seals, the brake piston, rotating assembly, port plate, head, and tightening bolts.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR CMR
Configuration: 336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR CMR
Configuration: 336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 23:17:07 UTC+0800 2020
10/10
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 En...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR CMR
Configuration: 336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 3 23:18:02 UTC+0800 2020
5/5
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR CMR
Configuration: 336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8
336E & 336E L Excavators CMR00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...