Caterpillar Cat D6T XW TRACK-TYPE TRACTOR (Prefix WLM) Service Repair Manual Instant Download.pdf

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6T XW TRACK-TYPE TRACTOR WLM
Configuration: D6T TRACK-TYPE TRACTOR XL, XW, LGP WLM00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
D6T Track-Type Tractor Power Train
Media Number -KENR8911-03 Publication Date -01/03/2016 Date Updated -07/03/2016
i04905929
Steering Planetary and Brake - Assemble
SMCS - 4132-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 138-7575 Link Bracket 3
D 6V-6640 Sealant 1
ReferenceRefer to Specifications, "Brake and Planetary" in the Service Manual for your machine.
Illustration 1 g00819345
Note: Orient the disc spring with the outer edge downward.
1/8
D6T TRACK-TYPE TRACTOR XL, XW, LGP WLM00001-UP (MACHINE) POWE...
2021/8/31
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

1. Install ring (30) and spring (29) in housing (5) .
2. Apply clean oil to seal ring (28) .
Note: Orient the seal ring with the lip downward. Refer to Illustration 2.
3. Install seal ring (28) in piston (24) .
4. Install piston (24) and O-ring seal (27) in the housing.
2/8
2021/8/31

5. Lower the temperature of bearing cups (25). Install bearing cups (25) in retainer (23) .
Note: Orient the seal ring with the lip downward. Refer to Illustration 4.
6. Apply clean oil to seal ring (26). Install seal ring (26) in retainer (23) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install retainer (23) on piston (24). Align the oil passage in retainer (23) with the oil passage
and the O-ring seal in the housing. Install bolts (22) .
3/8
2021/8/31

8. Install sun gear (18) in planetary carrier (10) .
9. Install bearings (21) in planetary gear (19) .
10. Install discs (20) and planetary gear (19) in planetary carrier (10). Install shaft (16) .
Note: If the rubber in pin (17) is damaged, replace pin (17) .
11. Align the hole in shaft (16) with the hole in planetary carrier (10) and install pin (17). Install
pin (17) until the pin is even with the surface of planetary carrier (10) .
12. Repeat Steps 9 through 11 for the remaining planetary gears.
4/8
2021/8/31

Note: If bearing cone (15) was removed from planetary carrier (10), a new bearing must be
installed.
13. Raise the temperature of bearing cone (15). Install the bearing cone on planetary carrier
(10) .
14. Apply Tooling (D) to the flange of slinger (12) .
15. Install slinger (12) on planetary carrier (10). Install bolts (13). Tighten the bolts to a torque
of 50 ± 10 N·m (37 ± 7 lb ft).
16. Install ring (14) in planetary carrier (10) .
17. Position housing (6) on planetary carrier (10) .
18. Raise the temperature of bearing cone (11). Install bearing cone (11) on planetary carrier
(10) .
5/8
2021/8/31

19. Position plate (9) onto the planetary carrier (10) .
Note: Install shim pack between plate (9) and planetary carrier (10), only if there was a
shim pack originally installed in the differential group and if the same planetary carrier is
being reused. Shim pack thickness should be 0.31 mm (0.0122inch).
20. Install bolts (8) .
21. Install friction discs (7) and brake plates. Alternate the friction discs and the brake plates.
6/8
2021/8/31

22. Position ring gear (5) on housing (6) .
23. Install bolts (4). Tighten bolts (4) to a torque of 135 ± 20 N·m (100 ± 15 lb ft).
24. Use a suitable lifting device and Tooling (A) in order to position the planetary group and
brake (1) on final drive (2). The weight of the planetary group and brake is approximately
135 kg (300 lb).
25. Install the bolts (3) .
End By: Install the final drive, the planetary group, and the brake.
7/8
2021/8/31

Shutdown SIS
Previous Screen
i04175780
Final Drive - Remove and Install
SMCS - 4050-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1952 Axle Removal Tool 1
B
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
2D-4593 5/8 - 11 by 5 1/2 inch 2
1B-4331 5/8 - 11 inch 2
2S-5658 Washer 4
Start By:
A. Separate the track.
Note: The planetary carriers of the final drives can be removed directly from the machine. Refer
to Disassembly and Assembly, "Final Drive Planetary Carrier (In Chassis) - Remove".
Without the sun gear in place, the brakes are ineffective. Personal
injury or death could result. Provide other means to hold or stop the
machine.
1/5
2021/8/31

1. Remove bolts (2) and cover (3) from final drive (1) .
2. Use Tooling (A) in order to remove axle (4) .
2/5
2021/8/31

3. Remove two bolts (5) .
4. Adjust the top bracket of Tooling (B) until Dimension (X) is 222.25 mm (8.750 inch).
3/5
2021/8/31

5. Remove two bolts (6) and the nuts from the sprocket segment. Discard bolts (6) and the
nuts.
6. Fasten Tooling (B) and a suitable lifting device to the final drive.
7. Remove bolts (7) that hold the final drive and the brake together.
4/5
2021/8/31

8. Use Tooling (B) to remove final drive (1) from the machine. The weight of final drive (1) is
approximately 454 kg (1000 lb).
Installation Procedure
1. Install final drive (1) in the reverse order of removal.
a. Tighten bolts (7) to a torque of 700 ± 90 N·m (516 ± 66 lb ft).
b. Lubricate new bolts (6) with SAE 30 oil. Install new bolts (6) and the nuts. Tighten
bolts (6) to a torque of 175 ± 40 N·m (130 ± 30 lb ft). Tighten bolts (6) an additional
1/3 turn.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 31 08:14:25 UTC+0800 2021
5/5
2021/8/31

Shutdown SIS
Previous Screen
i05236971
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
A
138-7573 Link Bracket 3
1A-2029 Bolt 1
B 1P-510 Driver Group 1
C
FT-1934 Beam 1
6V-3160 Double Acting Cylinder 1
6V-9061 Pump Group 1
1D-4621 Bolt 4
D
2A-1538 Bolt 2
Start By:
A. Remove the final drives.
1/6
2021/8/31

1. Install Tooling (A) and a suitable lifting device to planetary carrier (3) .
2. Remove bolts (1). Remove planetary carrier (3) and the two O-ring seals from the hub. The
weight of planetary carrier (3) is approximately 137 kg (302 lb).
3. Remove retainers (2) .
4. Place support under planetary carrier (3) in order to prevent damage. Use Tooling (B) and a
suitable press to remove the planetary gear shafts.
5. Remove planetary gears (4) from planetary carrier (3) .
2/6
2021/8/31

6. Remove bearing cones (5) from gears (4) .
7. Remove the bearing cups from each side of the gears.
8. Remove bolts (6) and retainer (7) .
3/6
2021/8/31

9. Attach a suitable lifting device to hub (12) and ring gear (8). The weight of hub (12) and
ring gear (8) is approximately 68 kg (150 lb). Remove hub (12) and ring gear (8) .
10. Turn over hub (9) and ring gear (8). Remove retaining ring (10). Attach a suitable lifting
device to hub (9). The weight of hub (9) is approximately 37 kg (82 lb). The weight of ring
gear (8) is approximately 32 kg (71 lb). Remove hub (9) .
11. Install Tooling (C) on hub (12).
Note: Do not lift hub (12) too high. Do not allow hub (12) to contact the fitting on the
hydraulic cylinder.
12. Use Tooling (C) to loosen hub (12) from spindle (13). Remove Tooling (C) .
13. Remove bearing cone (11) .
4/6
2021/8/31

14. Install Tooling (D) and a suitable lifting device to hub (12). Remove hub (12) from spindle
(13). The weight of hub (12) is approximately 180 kg (397 lb).
15. Turn over hub (12). Remove Duo-Cone seal kit (15). Use a hammer and a punch to remove
bearing cup (16) .
16. Turn over the hub. Remove bearing cup (14) from the hub.
Note: If the Duo-Cone seal will be reused, mark the seal kits for installation purposes.
5/6
2021/8/31

Note: Bearing cone (18) may be damaged if the bearing cone is removed from spindle (13) .
17. Remove Duo-Cone seal (19) from spindle (13) .
18. If necessary, remove bearing cone (18) from the spindle.
19. Remove lip seal (17) from spindle (13) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 31 08:15:24 UTC+0800 2021
6/6
2021/8/31

Shutdown SIS
Previous Screen
i04164792
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
A
1A-2029 Bolt 3
B 1P-0510 Driver Group 1
D
2A-1538 Bolt 2
E 1U-6437 Duo-Cone Seal Installer As 1
1. Apply clean oil to all the parts during assembly.
1/7
2021/8/31

2. Use Tooling (B) to install lip seal (17) in spindle (13) to a minimum depth of 9.65 mm (0.4
inch). Do not apply excessive force to lip seal (17) during installation in order to avoid
damaging the seal. Put clean oil on the lip of the seal.
3. Raise the temperature of bearing cone (18) to a maximum temperature of 135 °C (275 °F).
Install bearing cone (18) on spindle (13) .
Note: Before the installation of the Duo-Cone seal, refer to Disassembly and Assembly,
"Duo-Cone Conventional Seals - Install" for the correct procedure.
4. Use Tooling (E) to install the Duo-Cone seal on spindle (13) .
5. Lower the temperature of bearing cups (14) and (16). Install bearing cups (14) and (16) in
hub (12) .
6. Use Tooling (E) to install the Duo-Cone seal in hub (12) .
2/7
2021/8/31

7. Install Tooling (D) on hub (12). Attach a suitable lifting device to Tooling (D). Carefully
position hub (12) on spindle (13) .
8. Raise the temperature of bearing cone (11). Install bearing cone (11) on spindle (13).
3/7
2021/8/31

9. Attach a suitable lifting device to hub (9) and position hub (9) in ring gear (8). Install
retaining ring (10) .
10. Turn over the hub (9) and ring gear (8). Attach a suitable lifting device to hub (9) and the
ring gear (8) into position in hub (12).
11. Put retainer (7) into position. Install bolts (6) while the hub is slowly rotated. Tighten bolts
(6) evenly to a torque of 135 ± 15 N·m (100 ± 11 lb ft). The retainer must contact the end of
spindle (13) after bolts (6) have been tightened.
4/7
2021/8/31

12. Lower the temperature of bearing cups (20) and (21). Install the bearing cups in three
planetary gears (4) .
5/7
2021/8/31

13. Position the planetary carrier in a press. The shaft (22) must be in position with proper
support in order to be a positive stop for the shaft.
NOTICE
The shaft must be correctly installed. If the shaft is incorrectly
installed, the bearing preload will be incorrect. This will result in
component damage.
14. Position planetary gear (4) in the planetary carrier.
15. Lower the temperature of shaft (22). Use a suitable press to install the shaft in the planetary
carrier. After the installation, the end of shaft (22) must be flush with the retainer of the
planetary carrier. This will provide the correct bearing preload. The gear must rotate by
hand after installation. If the gear does not rotate, the problem must be corrected. Repeat
this procedure for all three shafts.
16. Install three retainers (2) on shafts (22) .
17. Install Tooling (A). Attach a suitable lifting device to Tooling (A). Install the two O-ring
seals on the planetary carrier. Align the drain hole in the planetary carrier with the drain
hole in the hub.
18. Position the planetary carrier in the hub.
19. Install bolts (1) that hold planetary carrier (3) to the hub. Remove Tooling (A) .
End By: Install the final drives.
Tue Aug 31 08:16:24 UTC+0800 2021
6/7
2021/8/31

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Shutdown SIS
Previous Screen
i06852073
Final Drive, Steering Differential, and Brake (Left Side) -
Remove and Install
SMCS - 4050-010-LT; 4132-010-LT
Removal Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A
FT-1952 Axle Removal Tool 1
1U-7432 Adapter Assembly 1
B
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
1D-4615 Bolt 2
1B-4331 Nut 2
5P-8248 Washer 4
C 1B-4331 Nut 1
5P-8248 Washer 2
8S-9906 Ratchet Puller 1
1A-1460 Bolt 1
5P-8245 Washer 1
1/10
2021/8/31

Caterpillar Cat D6T XW TRACK-TYPE TRACTOR (Prefix WLM) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from f8ioseoodkmmd

More from f8ioseoodkmmd (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat D6T XW TRACK-TYPE TRACTOR (Prefix WLM) Service Repair Manual Instant Download.pdf