This document provides instructions for disassembling the transmission of a 428D backhoe loader. It describes removing the transmission from the machine and then disassembling the major transmission components. These include removing the output shafts on the front and rear of the transmission, along with the input shaft. Bearings and gears are then removed from each shaft. The transmission case is also disassembled by removing bearing cups. Tools required for disassembly are listed.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428D BACKHOE LOADER BLL
Configuration: 428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01457233
Transmission (Direct Drive) - Remove
SMCS - 3030-011-DD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 2
8S-7611 Tube 2
8S-7615 Pin 2
B 1U-9760 Jack Stand 2
C 1U-7505 Transmisson Jack 1
D 1U-7558 Mounting Brackets 2
E FT-2535 Engine Support Bar Assembly 1
Start By:
A. Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
B. Remove the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear) -
Remove and Install".
C. Remove the piston pump. Refer to Disassembly and Assembly, RENR3585, "Piston Pump
(Implement and Steering) - Remove".
1. Use a suitable lifting device in order to raise the machine to a height of 91.4 mm (36 inch)
between the ground and the side step.
1/5
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00760888
2. Place tooling (A) under rear frame (1) .
Illustration 2 g00760890
3. Place tooling (B) under front axle (2) .
2/5
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00762355
4. Remove inspection plate (3). Install tooling (E) in order to support the engine.
Illustration 4 g00762357
5. Remove plug (4) and drain the transmission oil into a suitable container. The capacity of the
transmission is 18.5 L (4.9 US gal).
Illustration 5 g00762358
6. Remove four bolts (5) .
7. Repeat Step 6 for the opposite side.
8. Remove two bolts (6) .
3/5
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00762561
9. Disconnect three electrical connectors (7) .
Illustration 7 g00762562
10. Loosen bolt (8) and slide rod assembly (9) off the transmission lever.
Illustration 8 g00762359
4/5
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00762473
11. Support transmission (10) with tooling (C), as shown.
12. Attach tooling (D) to tooling (C) and transmission (10) in order to maintain a good balance.
Illustration 10 g00762479
13. Remove fourteen bolts (11) .
14. Carefully move transmission (10) away from the engine in order to clear the torque
converter. Lower transmission (10) to the ground. The weight of transmission (10) is 185 kg
(408 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 07:33:21 UTC+0800 2019
5/5
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428D BACKHOE LOADER BLL
Configuration: 428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01380368
Transmission (Direct Drive) - Disassemble
SMCS - 3030-015-DD; 3066-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-5750 Engine Stand 1
B 6V-2157 Link Bracket 1
C 9S-9152 Puller Assembly 1
C 5F-7465 Puller 1
C 3/8inch x 6inch Bolt 2
D 4C-3652 Spring Compressor 1
E 1U-6405 Puller 1
F 4C-3802 Puller 1
G 8H-0663 Puller 1
G 5F-7465 Puller 1
H 8B-7551 Puller 1
H 6V-3010 Puller 1
I 137-8102 Spring Compressor 1
J 4C-3089 Puller 1
1/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. K 1P-1859 Snap Ring Pliers 1
Start By:
A. Remove the transmission. Refer to Disassembly and Assembly, "Transmission (Direct
Drive) - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: The transmission will be disassembled in major components. The major components will
then be disassembled.
Illustration 1 g00728888
1. Install transmission (1) on tooling (A) .
2/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g00728895
2. Remove Implement pump drive shaft (2) from transmission (1) .
Illustration 3 g00728902
3. Remove plug (3). Drain the transmission oil into a suitable container. The capacity of the
transmission is 11.3 L (3 US gal).
Illustration 4 g00728906
3/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 4. Remove bolt (6), washer (5), and yoke (4) .
Illustration 5 g00728913
5. Attach tooling (B) to case (7). Attach a suitable lifting device to tooling (B). Remove
fourteen bolts (8). Remove case (7) from the transmission. The weight of case (7) is 42 kg
(94 lb).
(Direct Drive) Output Shaft (Front)
Illustration 6 g00728940
1. Remove front output shaft (9) .
4/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 7 g00728943
2. Use tooling (C) in order to remove bearing cone (10) .
Illustration 8 g00728944
3. Use tooling (E) in order to remove bearing cone (11) and gear (12) .
Illustration 9 g00728945
4. Remove two roller bearings (13), spacer (14), needle bearing (15), and thrust washer (16) .
5/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 10 g00728948
5. Remove retainer (17) and clutch pack (18) .
Illustration 11 g00728950
6. Use a suitable press and tooling (D) in order to compress spring (19). Use tooling (K) in
order to remove snap ring (20) .
6/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 12 g00728952
7. Remove snap ring (20), retainer (21), and spring (19) .
Illustration 13 g00728953
8. Release piston (22) by blowing shop air into the lube passage, as shown.
Illustration 14 g00729060
9. Use a seal pick in order to remove the seals from piston (22) .
(Direct Drive) Output Shaft (Rear)
7/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 15 g00729062
1. Remove screws (24) from each of the gearshift rods (23) .
Illustration 16 g00729064
2. Remove plug (25) .
Illustration 17 g00729196
8/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Remove plug (25), O-ring (26), two springs (27), and three balls (28). Remove two gearshift
rods (23) from shift forks (29) .
Illustration 18 g00729197
4. Use tooling (E) in order to remove bearing (30), gear (31), and gear (32) .
Illustration 19 g00729198
5. Remove bearings (33), spacer (34), and synchronizer (35) .
9/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 20 g00729199
6. Use tooling (F) in order to remove bearing (36) and gear (37). Remove synchronizer (38) .
Illustration 21 g00729200
7. Use tooling (K) in order to remove snap ring (39). Remove gear (40) and housing (41) .
Illustration 22 g00729201
8. Use tooling (E) in order to remove gear (42) .
10/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. (Direct Drive) Shaft
1. Remove the shaft by hand for disassembly.
Illustration 23 g00729202
2. Use tooling (G) in order to remove bearings (43) and (44) .
(Direct Drive) Reverse Shaft
1. Remove the reverse shaft by hand for disassembly.
Illustration 24 g00729204
2. Use tooling (G) in order to remove bearings (45) and (46) .
(Direct Drive) Input Shaft
1. Remove the input shaft by hand for disassembly.
11/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 25 g00729207
2. Use tooling (H) in order to remove bearing (47) .
Illustration 26 g00729208
3. Use tooling (K) in order to remove snap ring (48). Remove spacer (49), needle bearing (50),
and gear (51) .
Illustration 27 g00729210
12/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove retainer (52) and clutch pack (53) .
Illustration 28 g00729213
5. Use tooling (I) and a suitable press in order to compress spring (55). Use tooling (K) in
order to remove snap ring (54). Remove the retainer and spring (55) .
Illustration 29 g00729257
6. Release piston (56) by blowing shop air into the lube passage, as shown.
13/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 30 g00729258
7. Use a seal pick in order to remove the seals from piston (56) .
Illustration 31 g00729260
8. Use tooling (J) in order to remove bearing (57) and gear (58) .
Illustration 32 g00729261
9. Remove gear (59) from the clutch pack.
14/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 10. Repeat Steps 4 through 7 for the remainder of the input shaft.
Transmission Case
Illustration 33 g00729262
Note: Record the measurement and placement of the shims behind the bearing cups in order
to aid in assembly.
1. Remove bearing cups (60), (61), (62), (63), and (64) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 07:34:17 UTC+0800 2019
15/15
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engin...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428D BACKHOE LOADER BLL
Configuration: 428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Power
Train
Media Number -RENR3578-12 Publication Date -01/04/2010 Date Updated -13/04/2010
i01381641
Transmission (Direct Drive) - Assemble
SMCS - 3030-016-DD; 3066-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 137-8102 Spring Compressor 1
B 1P-1859 Snap Ring Pliers 1
C 4C-3652 Spring Compressor 1
D 6V-2157 Link Bracket 1
E 8T-5096 Indicator 1
F 1U-5750 Engine Stand 1
Note: The transmission will be assembled in major components. The major components will then
be assembled.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply a light film of clean transmission oil to all components before assembly.
Transmission case
1/14
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00729262
Note: Install the shims behind each bearing cup that was recorded on the disassembly
procedure.
1. Install bearing cups (60), (61), (62), (63), and (64) .
(Direct Drive) Input Shaft
Illustration 2 g00731364
1. Install the needle thrust bearings on the shafts. The open end of cups (1) must point away
from the bearings or gears that are contacted.
2/14
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 3 g00729745
2. Install the seals on piston (56) .
Illustration 4 g00729752
3. Install piston (56). Install the retainer and spring (55). Use tooling (A) and a suitable press
in order to compress spring (55). Use tooling (B) in order to install snap ring (54) .
Illustration 5 g00729210
3/14
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 4. Install clutch pack (53) and retainer (52) .
5. Repeat Steps 2 through 4 for the opposite end of the input shaft.
Illustration 6 g00729208
6. Install gear (51), needle bearing (50), and spacer (49). Use tooling (B) in order to install
snap ring (48) .
Illustration 7 g00729771
7. Heat bearing cone (57) to 135 °C (275 °F). Install bearing cone (57) .
8. Install the input shaft.
(Direct Drive) Reverse Shaft
4/14
428D Backhoe Loader BLL00651-00712 (MACHINE) POWERED BY 3054 Engine(...
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...