The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, counterbalance valve housing, and more. Tools and safety precautions are also listed to properly disassemble parts and release spring forces. The goal is to disassemble the major components to individual parts for inspection or replacement.
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
John Deere 12PB Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections for engine repair, fuel/air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repairs. It provides technicians with information needed for diagnosis, repair, and maintenance of the mowers.
John Deere 5E 2BV Blower Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, and fuel tank capacities. It also lists the blower type as centrifugal and single stage.
John Deere 3-179D OEM Engine Service Repair Manual.pdfdjdksmmdmd
This document provides an overview and table of contents for a technical manual covering 300 Series OEM Engines. It includes:
- Sections covering the engine and its components, auxiliary systems, electrical systems, sheet metal, PTO drive, and system testing.
- An index listing components and procedures alphabetically to aid navigation.
- Specification tables for torque values and engine data.
The manual is intended as a reference for experienced technicians servicing these engines, with concise instructions and specifications rather than theoretical background.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks before working under lifted components.
Kubota BX1500D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for using a parts book for an engine. It explains the column headings in parts book pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent. An example page from the parts book is then shown listing the specific parts for an engine with the corresponding information.
Clark EPG 15-18 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for parts, and procedures for servicing various systems of the forklift such as the battery, wiring, motors, brakes, hydraulics, tilt cylinders, and more. The document uses a standardized grouping and numbering system to organize the content and make specific sections and pages easy to locate.
Kubota BX2230D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. The remainder of the document lists specific part numbers and descriptions for a BX2230D tractor organized by system or component.
Kubota L35 Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. Finally, it provides an index of all product parts for reference L35 and lists the relevant parts book for each item.
Kubota G4200H Lawn mower Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for parts books, including definitions of column headings in parts number pages and notes about country codes. It then provides a sample page from a parts book for a G4200H product that lists over 200 individual part numbers, descriptions, quantities, serial number ranges, interchangeability, remarks and weights.
Komatsu SK714-5 Skid Steer Loader Service Repair Manual (SN 37AF01876 and up)...djdksmmdmd
This document provides shop manual instructions for adjusting valve clearance on Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. The instructions include removing covers to access the valves, rotating the drive shaft to specific positions, checking valve clearance with feeler gauges, adjusting clearance by turning screws, and reassembling covers. Clearance specifications and tightening torques are provided. The document also provides a zero setting procedure for the SK815-5 turbo model before performing the clearance adjustment.
John Deere Yanmar Engines 322, F912, F932 Service Repair Manual.pdfdjdksmmdmd
This document is a component technical manual for Yanmar gasoline engines. It contains instructions for repairing engines, fuel systems, and electrical systems. It also includes theory of operation, diagnostic procedures, and testing procedures. The manual should be used along with the machine's technical manual for information on removing and installing the engine, and accessing engine components. The manual emphasizes safety and provides illustrated, step-by-step instructions for diagnosis and repair of engine systems.
John Deere POWERTECH 4.5L & 6.8L Diesel Engines Base Engine Service Repair Ma...djdksmmdmd
This document provides instructions for servicing Powertech 4.5L and 6.8L diesel engines. It outlines five technical manuals that cover different aspects of the engines, with this document focusing on the base engine. The introduction provides safety information and explains how to use the manual, including cleaning the engine before repair. It directs technicians to companion manuals for fuel system repair, operation and diagnostics based on the specific fuel system for the engine being serviced.
Caterpillar Cat 324D FM EXCAVATOR (Prefix JKR) Service Repair Manual (JKR0000...djdksmmdmd
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It lists the required tools and presents a step-by-step procedure for disassembling the final drive components. This includes removing gears, seals, springs, and other parts. It then describes assembling the main housing, motor housing, and final drive components in reverse order.
Caterpillar Cat 324D FM EXCAVATOR (Prefix JGK) Service Repair Manual (JGK0000...djdksmmdmd
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It lists required tools and describes each step of the disassembly process, which includes removing plates, springs, pistons, gears, and other components. It also describes using a special bench and tooling to remove a locknut from the final drive assembly. Finally, it outlines the process for disassembling the main and motor housings, including removing bearings, seals, and other parts.
This document provides assembly instructions for the final drive of a 323F LN excavator in 3 sentences or less:
The document outlines the steps to assemble the final drive of a 323F LN excavator, including installing bearings, seals, gears, and other components in the correct order and orientation using various tools. Proper assembly requires precise measurement and installation of shims to achieve the correct bearing preload. Following the detailed multi-step process ensures the final drive is assembled correctly.
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator. The removal procedure involves taking off 12 components including adapters, gears, idler hubs and sleeve bearings. The installation procedure outlines 20 steps for reinstalling these components and ensuring proper orientation, alignment and torque specifications are followed. Proper cleaning and lubrication of parts is emphasized to prevent wear and damage.
Caterpillar Cat 323D SA Excavator (Prefix NES) Service Repair Manual (NES0000...djdksmmdmd
The document provides instructions for removing and installing the flywheel and flywheel housing on a C6.4 engine. It describes removing the muffler, crankshaft position sensor, bolts securing the flywheel, and installing lifting tools to remove the flywheel. It also details removing the flywheel housing bolts and oil seal, checking dowels and installing a new gasket and housing. Reinstallation involves installing the oil seal, flywheel housing, flywheel, crankshaft position sensor and muffler.
John Deere 113 172 Clipper Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, fuel tank capacities, and blower type. It also lists the 113 and 172 hedge clippers and 110G, 210G, 240G, and 260G trimmers but does not provide details for those machines.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 314F excavator. It outlines 16 steps to disassemble the final drive, removing components like the sprocket, traction control valve, and barrel assembly. It then details 14 steps to disassemble the counterbalance valve, removing springs, spools, and relief valves. Finally, it lists 10 steps to disassemble the travel motor, removing pistons, guides, plates and the barrel assembly. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
John Deere 110G, 210G, 240G 260G Trimmer Clutters Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
John Deere 12PB Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections for engine repair, fuel/air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repairs. It provides technicians with information needed for diagnosis, repair, and maintenance of the mowers.
John Deere 5E 2BV Blower Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, and fuel tank capacities. It also lists the blower type as centrifugal and single stage.
John Deere 3-179D OEM Engine Service Repair Manual.pdfdjdksmmdmd
This document provides an overview and table of contents for a technical manual covering 300 Series OEM Engines. It includes:
- Sections covering the engine and its components, auxiliary systems, electrical systems, sheet metal, PTO drive, and system testing.
- An index listing components and procedures alphabetically to aid navigation.
- Specification tables for torque values and engine data.
The manual is intended as a reference for experienced technicians servicing these engines, with concise instructions and specifications rather than theoretical background.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks before working under lifted components.
Kubota BX1500D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for using a parts book for an engine. It explains the column headings in parts book pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent. An example page from the parts book is then shown listing the specific parts for an engine with the corresponding information.
Clark EPG 15-18 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for parts, and procedures for servicing various systems of the forklift such as the battery, wiring, motors, brakes, hydraulics, tilt cylinders, and more. The document uses a standardized grouping and numbering system to organize the content and make specific sections and pages easy to locate.
Kubota BX2230D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. The remainder of the document lists specific part numbers and descriptions for a BX2230D tractor organized by system or component.
Kubota L35 Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. Finally, it provides an index of all product parts for reference L35 and lists the relevant parts book for each item.
Kubota G4200H Lawn mower Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for parts books, including definitions of column headings in parts number pages and notes about country codes. It then provides a sample page from a parts book for a G4200H product that lists over 200 individual part numbers, descriptions, quantities, serial number ranges, interchangeability, remarks and weights.
Komatsu SK714-5 Skid Steer Loader Service Repair Manual (SN 37AF01876 and up)...djdksmmdmd
This document provides shop manual instructions for adjusting valve clearance on Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. The instructions include removing covers to access the valves, rotating the drive shaft to specific positions, checking valve clearance with feeler gauges, adjusting clearance by turning screws, and reassembling covers. Clearance specifications and tightening torques are provided. The document also provides a zero setting procedure for the SK815-5 turbo model before performing the clearance adjustment.
John Deere Yanmar Engines 322, F912, F932 Service Repair Manual.pdfdjdksmmdmd
This document is a component technical manual for Yanmar gasoline engines. It contains instructions for repairing engines, fuel systems, and electrical systems. It also includes theory of operation, diagnostic procedures, and testing procedures. The manual should be used along with the machine's technical manual for information on removing and installing the engine, and accessing engine components. The manual emphasizes safety and provides illustrated, step-by-step instructions for diagnosis and repair of engine systems.
John Deere POWERTECH 4.5L & 6.8L Diesel Engines Base Engine Service Repair Ma...djdksmmdmd
This document provides instructions for servicing Powertech 4.5L and 6.8L diesel engines. It outlines five technical manuals that cover different aspects of the engines, with this document focusing on the base engine. The introduction provides safety information and explains how to use the manual, including cleaning the engine before repair. It directs technicians to companion manuals for fuel system repair, operation and diagnostics based on the specific fuel system for the engine being serviced.
Caterpillar Cat 324D FM EXCAVATOR (Prefix JKR) Service Repair Manual (JKR0000...djdksmmdmd
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It lists the required tools and presents a step-by-step procedure for disassembling the final drive components. This includes removing gears, seals, springs, and other parts. It then describes assembling the main housing, motor housing, and final drive components in reverse order.
Caterpillar Cat 324D FM EXCAVATOR (Prefix JGK) Service Repair Manual (JGK0000...djdksmmdmd
This document provides instructions for disassembling and assembling the final drive of a 324D FM excavator. It lists required tools and describes each step of the disassembly process, which includes removing plates, springs, pistons, gears, and other components. It also describes using a special bench and tooling to remove a locknut from the final drive assembly. Finally, it outlines the process for disassembling the main and motor housings, including removing bearings, seals, and other parts.
This document provides assembly instructions for the final drive of a 323F LN excavator in 3 sentences or less:
The document outlines the steps to assemble the final drive of a 323F LN excavator, including installing bearings, seals, gears, and other components in the correct order and orientation using various tools. Proper assembly requires precise measurement and installation of shims to achieve the correct bearing preload. Following the detailed multi-step process ensures the final drive is assembled correctly.
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator. The removal procedure involves taking off 12 components including adapters, gears, idler hubs and sleeve bearings. The installation procedure outlines 20 steps for reinstalling these components and ensuring proper orientation, alignment and torque specifications are followed. Proper cleaning and lubrication of parts is emphasized to prevent wear and damage.
Caterpillar Cat 323D SA Excavator (Prefix NES) Service Repair Manual (NES0000...djdksmmdmd
The document provides instructions for removing and installing the flywheel and flywheel housing on a C6.4 engine. It describes removing the muffler, crankshaft position sensor, bolts securing the flywheel, and installing lifting tools to remove the flywheel. It also details removing the flywheel housing bolts and oil seal, checking dowels and installing a new gasket and housing. Reinstallation involves installing the oil seal, flywheel housing, flywheel, crankshaft position sensor and muffler.
John Deere 113 172 Clipper Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, fuel tank capacities, and blower type. It also lists the 113 and 172 hedge clippers and 110G, 210G, 240G, and 260G trimmers but does not provide details for those machines.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 314F excavator. It outlines 16 steps to disassemble the final drive, removing components like the sprocket, traction control valve, and barrel assembly. It then details 14 steps to disassemble the counterbalance valve, removing springs, spools, and relief valves. Finally, it lists 10 steps to disassemble the travel motor, removing pistons, guides, plates and the barrel assembly. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
John Deere 110G, 210G, 240G 260G Trimmer Clutters Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreaching or pointing tools at people, and always shut off engines before adjusting or refueling.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR FEB
Configuration: 313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i06303560
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
C 8T-6699 Bolts 2
D
1P-0074 Slide Hammer Puller Gp 1
4C-5666 Threaded Adapter 1
123-6702 Backlash Gauge Gp 1
E 1P-0510 Driver Gp 1
F 8H-0663 Bearing Puller Gp 1
G 1P-1863 Retaining Ring Pliers 1
H 9U-7346 Spanner Wrench As 1
Start By:
a. Remove the final drive and the travel motor. Refer to Disassembly and Assembly Manual ,
"Final Drive and Travel Motor - Remove".
NOTICE
1/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor. The weight of the sprocket is
approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
2/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g00940682
4. Use Tooling (A) and a suitable lifting device to position the final drive and the travel motor
onto Tooling (B). The combined weight of the final drive and travel motor is approximately
170 kg (375 lb).
5. Drain the oil from the final drive into a suitable container for storage or for disposal. Refer
to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the final
drive.
6. Remove fittings (1). Remove fittings (2) from traction control valve (3).
7. Remove nine bolts (4) that secure traction control valve (3) to the final drive.
8. Use two persons to remove traction control valve (3) from the final drive. The weight of
travel brake valve (3) is approximately 27 kg (60 lb).
3/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g00940716
9. Remove valve plate (5) and O-ring seal (6).
Illustration 3 g01405139
10. Use Tooling (D) to remove bearing (7).
Disassembly of the Counterbalance Valve
Illustration 4 g01405725
4/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 5 g01405227
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Position the counterbalance valve, as shown. Remove plug (8) and adapter (9).
2. Remove spring (10) and spool (11).
Illustration 6 g01405232
5/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Remove relief valve assemblies (12).
Illustration 7 g01405243
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove seat (13). Seat (13) is pressed onto valve (17). Use new parts if seat (13) or valve
(17) is damaged. Do not disassemble these components. Make sure that you reuse the other
component.
5. Remove backup ring (14) and O-ring seal (15).
6. Remove O-ring seal (22).
7. Remove nut (20).
8. Remove screw (27).
9. Remove stopper (26). Remove backup ring (19) and O-ring seal (18) from stopper (19).
10. Remove valve (21), piston (25), and spring (16) from the housing.
11. Remove backup ring (23) and O-ring seal (24) from piston (25).
6/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 8 g01405284
Illustration 9 g01405299
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove covers (28) and the O-ring seals.
13. Remove springs (29), guides (30), and spool assembly (31).
7/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 10 g01405345
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
14. Remove valve (32), spring (33), and ball (34) from one end of spool (35). Repeat for the
other end of spool (35).
Illustration 11 g01405633
8/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Remove plug (36), spring (38), and piston (39) from both sides of the housing assembly.
16. Remove O-ring seal (37) from each plug (36).
Note: Remove the remaining allen head bolts from the housing assembly for cleaning
purposes, if necessary. Each allen head bolt has an O-ring seal. Check the O-ring seal for
wear or for damage. Replace the O-ring seal, if necessary.
Disassembly of the Travel Motor
Illustration 12 g01405794
1. Remove O-ring seal (40) and springs (41).
9/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 13 g01405828
2. Install Tooling (C) onto piston assembly (42). Use Tooling (C) and a suitable prybar to
remove piston assembly (42) from body (43).
Illustration 14 g01405855
3. Remove O-ring seals (45) and (46) from piston assembly (42). Remove backup rings (44)
and (47) from piston assembly (42).
10/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 15 g01405867
4. Use suitable drivers or a suitable lever to remove guide assembly (48).
Illustration 16 g01405885
5. Remove O-ring seal (49) and backup ring (50) from guide assembly (48).
11/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 17 g01406117
6. Remove four separator plates (51) and four friction plates (52). Note the alternating order of
separator plates (51) and friction plates (52) for assembly purposes.
Note: Do not allow the components of barrel assembly (53) to come apart while you
remove barrel assembly (53). The components of barrel assembly (53) must be reinstalled
into the original positions.
Note: Oil will drain from the final drive. Place a suitable container under the final drive for
storage or disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for
the fluid capacity of the final drive.
7. Position the final drive horizontally.
8. Remove barrel assembly (53).
12/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 18 g01406180
Note: Mark the component locations for assembly purposes before you disassemble barrel
assembly (53).
9. Remove piston assemblies (54) and retainer (55) from barrel assembly (53).
Illustration 19 g01406210
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
10. Remove retainer (56), spacer (57), and springs (58) from barrel assembly (53).
13/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 20 g01406263
11. Put location marks on cam plate (59) for assembly purposes. Make sure that the thick end of
cam plate (59) is adjacent to the opening that is across body (43). Remove cam plate (59).
Illustration 21 g01406329
Illustration 22 g01406338
14/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove piston (60) and spring (62).
13. Remove key (61).
Disassembly of the Final Drive
Illustration 23 g01406376
1. Use a suitable lifting device to position the final drive on Tooling (B), as shown. The weight
of the final drive is approximately 200 kg (441 lb).
2. Remove plugs (63). Remove the O-ring seals from plugs (63). Check the O-ring seals for
wear or for damage. Replace the O-ring seals, if necessary.
3. Remove bolts (65). Remove cover (64).
15/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 24 g01406386
4. Raise the temperature of bolts (66) in order to loosen the thread sealant.
5. Remove bolts (66) and plate (67).
Illustration 25 g01406397
6. Remove sun gear (68).
16/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 26 g01406400
7. Attach Tooling (A) and a suitable lifting device to carrier assembly (69). Remove carrier
assembly (69), planetary gear assembly (70), and bearing assembly (71) as a unit.
Illustration 27 g01406789
8. Remove planetary gear (70) and bearing assembly (71) from carrier assembly (69). Remove
the remaining planetary gears (70) and bearings (71).
Illustration 28 g01406822
9. Remove sun gear (72).
17/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Raise the temperature of bolts (73) in order to loosen the thread sealant. Remove bolts (73).
Remove plate (74).
Illustration 29 g01406850
11. Remove retaining ring (75) from sun gear (72). Check retaining ring (75) for wear or for
damage. Replace retaining ring (75), if necessary.
Illustration 30 g01406853
12. Remove planetary gear (76).
18/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 31 g01406875
13. Remove bearing (77), race (78), and thrust washer (79).
14. Repeat Steps 12 and 13 in order to remove the remaining planetary gear assemblies.
Illustration 32 g01406882
15. Remove bolt (80) and plate (81).
19/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 33 g01406885
Illustration 34 g01406886
16. Use Tooling (H) to remove nut (82).
Illustration 35 g01406906
17. Install Tooling (A) and a suitable lifting device to housing (83). The weight of housing (83)
is approximately 35 kg (77 lb).
18. Remove housing (83) from body assembly (84).
20/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 36 g01406912
19. Remove Duo-Cone Seal Gp seal (85) from the body assembly. Remove the Duo-Cone Seal
Gp seal from the housing.
Illustration 37 g01407100
20. Remove both bearings (86) from housing (83).
21/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 38 g01407089
21. Remove both bearings (87) from housing (83).
Illustration 39 g01407115
22. Position body assembly (84) horizontally. Remove shaft assembly (88), the bearing, and the
retaining ring.
22/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 40 g01407144
23. Use Tooling (G) to remove retaining ring (89) from shaft assembly (88).
Illustration 41 g01407161
24. Use Tooling (E), Tooling (F), and a suitable press to remove bearing (90).
Illustration 42 g01407166
25. Remove lip seal (91) from the body assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 16 00:46:32 UTC+0800 2020
23/23
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313D2 EXCAVATOR FEB
Configuration: 313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
313D2 Excavator Machine Systems
Media Number -UENR7323-03 Publication Date -01/09/2015 Date Updated -14/12/2017
i07219742
Final Drive and Travel Motor - Disassemble
SMCS - 4050-015; 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 422-5474 M16x2x24 mm Lifting Eye Assembly 2
B 1P-2420 Transmission Repair Stand 1
C 8H-0663 Bearing Puller Assembly 1
D 422-5473 M12x1.75x21 mm Lifting Eye Assembly 2
E 422-5472 M10x1.5x16 mm Lifting Eye Assembly 2
F 1U-9895 Crossblock 1
Start By:
a. Remove the final drive and the travel motor assembly.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
2. Remove the sprocket from the final drive and the travel motor assembly. The weight of the
sprocket is approximately 39 kg (85 lb).
3. Mark the alignment of the final drive and travel motor for reassembly purposes. The parts
must be reinstalled in the original locations.
Illustration 1 g06256385
4. Use Tooling (A) and a suitable lifting device to position final drive assembly (1) onto
Tooling (B). The weight of final drive assembly (1) is approximately 163 kg (360 lb).
2/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. 5. Drain the oil from final drive assembly (1) into a suitable container for storage or for
disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity
of the final drive.
Illustration 2 g06256798
6. Remove plug (2), plugs (3), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06256843
3/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 4 g06256845
7. Remove plugs (4) and the O-ring seals.
8. Remove plug (5), spring (7), valve (6), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 5 g06256847
4/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 6 g06256848
9. Remove plug (8), spring (9), valve (10), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 7 g06256982
5/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 8 g06256984
10. Remove plug (11), spring (13), seat (12), and the O-ring seals.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 9 g06257015
6/22
313D2 GC & 313D2 L Excavators FEB00001-UP (MACHINE) POWERED BY C4.4 ...
2020/5/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...