Orgonite Towerbuster "Dirty Harry" is the most versatile of all orgonites. We use it to convert cellphone masts into positive orgone generators, to gift water courses and place it wherever we feel the energy needs an upgrade. Think: power stations, large manufacturing plants, police stations, prisons, abbatoirs, cemetaries, your place of work, corporate headquarters, places of political power, religious indoctrination, satanic ritual...(use your imagination)
2. Shopping List for Ingredients
• Standard Muffin Mould 100-150 ml (3-5 oz.)
• Polyester Resin – clear
• Aluminium shavings / filings
• Clear quartz crystals, that is. But they can also be milky or
otherwise of “inferior quality”. any small crumbs of crystal
breakage will suffice
• The catalyst that will bring about the chemical reaction that
makes the resin cure.
• Pigment (if you would like colour)
• Silicone release wax / baking fat
• A protective mask (against organic fumes as with spray
painters)
• Gloves
• Apron
• Containers to hold the shavings and crystal chips separately.
• Sponge
• Mixing Jug
• Pouring container
• Mixing Bucket
• Dowel rod to stir bucket with if you add pigment
3. 1. Wax the form
We make our TBs in standard muffin moulds, but you can use anything that will hold
approximately 100-150 ml (3-5 oz.) of resin and shavings. Plastic or paper cups are also
popular.
If you want to re-use the mould, we strongly recommend that you wax it before pouring.
We use “silicone release wax” which we get from the place that sells the resin and catalyst.
Baking fat will work as well.
4. 2. We start with a thin layer of filings and place
the crystals on top of this little nest. That way they will
end up being approximately at the centre of the
finished TB
5. 3. We fill the form up to just under the rim. If you want
to add some crushed pyrite or tourmaline, you can
sprinkle it over the top layer in the end.
6. 4. Pouring Procedure
• We need the resin, and a suitable
quantity of catalyst. The resin suppliers
normally sell special measuring bottles
for the catalyst and we recommend that
you get one if it is not supplied for free
• We also recommend that you use
industrial strength rubber gloves for the
larger works while surgical latex gloves
are good for finer work.
• If you plan to do this often you should get
yourself a mask with a filter against
organic solvent vapours. You do not really
need that if you can work outside.
7. 5. Wear a mask if you frequently do this inside.
Make sure rooms are well ventilated.
8. 6. Use bucket with measurements
7. Pour a sufficient quantity of resin into a bucket with
measurements. For one standard muffin tray, we use
approx 1.1-1.2 litres.
9. 8. Measure & Add Catalyst
With most makes of resin the
standard mix is 2% catalyst at
20 C. But beware: temperature
and size of the piece you want
to pour influence the need for
catalyst. The hotter it gets or
the bigger the piece, the least
catalyst you need. Refer to resin
manufacturer’s manual for
exact quantities.
12. 11. Pour into small jug with spout for
easier pouring
13. 12. Start pouring and continue
until the muffin pan is filled
to the rim
Since the resin takes a while to sink in you will
have to pour in several passes. It is always good
to have a few more objects prepared on the
side that can take any surplus resin in case you
have miscalculated the quantity.
You have (depending on the make of the resin
and room temperature etc.) 15-25 minutes to
do this. That is normally not a problem. If you
feel that the resin is becoming jelly-like before
you are finished, quickly mix the remaining
resin with metal filings to make at least some
kind of usable orgonite .
Keeping your bucket and jugs clean helps to
avoid premature gelling.
14. 13. Last step
• When the process is finished, you have to wait a while.
The resin will now start its chemical reaction during
which it will get quite hot. If you have used the right
amount of catalyst, the TBs should be easily removed
after curing by just turning the pan upside down. A few
gentle taps with a rubber hammer are sometimes
needed.
If the mix has not cured properly (too cold or not
enough catalyst) it can be put in direct sunlight to give
it some after-curing.
15. THANK YOU
We hope you will enjoy making your own orgonite
Tower Busters. If you have any queries, please feel
free to email us on info@orgoniseafrica.com and we
will respond to your query within 24-48 hours
(allowing for time-zone differences).
If you enjoyed this presentation, you can
download it here
and we would be grateful if you would
Like us on Facebook