CCIE Real LAB TS 1.0 CCIEREALLABWORKBOOK.CO0

1. © 2014-2015 CCIEREALLABWORKBOOK.COM
August 10,
2014
© 2014-2015 CCIEREALLABWORKBOOK.COM 1
CCIE RSV5
WORKBOOK
© 2014-2015 CCIEREALLABWORKBOOK.COM
Troubleshooting Section
Version 1.0
Update: 2014-AUG-10

2. © 2014-2015 CCIEREALLABWORKBOOK.COM
August 10,
2014
© 2014-2015 CCIEREALLABWORKBOOK.COM 2
Disclaimer: CCCIE RSv5 lab Exam Workbook is designed to provide extensive practical information to
help candidates in the preparation for CISCO Systems CCIE RSv5 Lab Exam. We do not take liability or
responsibility to any person or entity with respect to loss or damage caused by the information
presented in the workbook.
Cisco, Cisco Systems, and CCIE (Cisco Certified Internetwork Expert) are registered trademarks of
Cisco Systems, Inc. And of its affiliates in the USA and other countries.
The information presented in the workbook is not necessarily related to Cisco Systems, Inc. This
workbook is not affiliated, endorsed or sponsored by Cisco Systems, Inc. This workbook provides
detailed and comprehensive practical examples for the preparation of CCIE RSv5 labs but
cannot be used as a replacement of other supplementary books or prescribed materials.
Purpose of the workbook is to provide more practical information about the CCIE RSv5 lab Exam.
This workbook is prepared for the individual candidates who have purchased it with non-
disclosure agreement. Imitation, copying, editing or posting contents of the workbook over the
internet is part of copyright and non-disclosure agreement violation.

3. © 2014-2015 CCIEREALLABWORKBOOK.COM
August 10,
2014
© 2014-2015 CCIEREALLABWORKBOOK.COM 3
Troubleshooting Guidelines
Important!!! Read the Following Guidelines Before Starting the Section
• This section is comprised of a set of troubleshooting scenarios.
• You have a maximum of 150 minutes to complete the section. A warning message will be
displayed after 120 minutes.
• The final score of this section is combined with the Configuration and the Diagnostic sections to
complete your final Pass or Fail status on the Cisco CCIE lab exam.
• Candidates must reach a minimum threshold in all three sections and achieve an overall cut
score in order to pass the CCIE certification.
1.You will be presented with preconfigured routers and switches In the topology. Do not change the
following configuration on the devices:
• Hostname
• Enable password "cisco"
• Console line configuration
2.For all the authentication configurations in the lab, password is "cisco" unless changed to introduce a
break
3.Points are awarded for finding and fixing inserted faults in the presented fully configured topology. An
inserted fault is an introduced break for a scenario that was previously working. Depending on the
scenario, fixing inserted faults could require one or multiple command lines on the same or
multiple devices.
4.The resolution of one incident may depend on the resolution of previous incident(s). The dependency
will not be visible if incidents are resolved in sequence.
5.There are no physical fault introduced in the presented topology.
6.Do not change any routing protocol boundaries. Refer to the provided diagrams
7.Do not remove any feature that Is configured In order to resolve an Incident; you must resolve the
misconfiguration rather than removing it all (examples. Access-lists.PBR.CoPP. MCC. and so on) The
only exception to this rule is when there is no other choice except to remove the faulty
configuration in order to resolve the incident.
8.Static and default routes are not permitted unless preconfigured These restrictions include floating
static routes and routes that are generated by a routing protocol. Routes to Null 0 that are
generated as a result of a dynamic routing protocol solution are permitted.
9.Tunneling and policy-routing are not permitted unless They are preconfigured.
10.Points will be deducted for every incident in which a prohibited solution is used.
11.Candidates have control of all required devices in the topology.

4. © 2014-2015 CCIEREALLABWORKBOOK.COM
August 10,
2014
© 2014-2015 CCIEREALLABWORKBOOK.COM 4
Question 1:
PC 110 cannot access R7/R8, fix the problem so that PC 110 can ping R7
Solutions
SW2:
SW2 (config) #int e0/0
SW2 (config-if) #switchport access vlan 100
Question 2:
R17 should have one default route which points to R12 via PPP as shown below
R17# sh ip route
S* 0.0.0.0/0 via 202.34.7.25
172.16.0.0/16 is variable subnetted, 4 subnets, 3 masks
C 172.16.3.56/30 is directly connected, Ethernet 0/0
L 172.16.3.57/32 is directly connected, Ethernet 0/0
C 172.16.3.88/29 is directly connected via Tunnel 0
L 172.16.3.90/32 is directly connected via Tunnel 0
202 .34.7.0/32 is subnetted. 2 subnets
C 202.34.7.25 is directly connected via Serial 1/0
C 202.34.7.26 is directly connected via Serial 1/0
Solutions
R17:
interface Serial1/0
ip address negotiated
encapsulation ppp
ppp chap password 0 CCIErock$
ppp ipcp route default