Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Wobd2-autel maxi das ds708 connection tips

179 views

Published on

Buy Autel MaxiDAS DS708 Get MaxiTPMS TS401 As Free Gift
1. One Year Free Update Online!
2. Shipped from our US warehouse directly, NO TAX, with fast delivery
3. Wifi Available, Cover more than 40 brands of Vehicles from US, Asian and European

Published in: Technology
  • Be the first to comment

  • Be the first to like this

Wobd2-autel maxi das ds708 connection tips

  1. 1. Autel MaxiDAS DS708 Connection Tips How to connect the genuine Autel MaxiDAS DS708 to a vehicle? The method used to connect Autel DS708 to a vehicle's DLC depends on the vehicle's configuration--- with OBD II vehicle management system or not. This is about original Autel MaxiDAS DS708 connection. Hope it can help you out. Ps. This connection tips are better for DS708 at www.wobd2.com. OBD II vehicles supply both communication and 12-volt power through a standardized J-1962 data link connection (DLC). Non-OBD II vehicles supply communication through a DLC connection and sometimes supplies 12-volt power through the cigarette lighter receptacle or a connection to the battery.
  2. 2. a. OBD II Vehicle Cable Connection Requirement: OBD II adapter; 15-pin main cable; steps: 1. Locate the required OBD II adapter and connect it into the 15-pin male connector of the main cable.
  3. 3. 2. Connect the cable's 15-pin female adapter to the DB 15-pin port on the top of the scan tool. Finger tighten the connecting screws. 4. Connect the cable's OBD II adapter into the vehicle's DLC, located under the vehicle dash
  4. 4. NOTE: Extension cable can be used between the scan tool and the 15-pin main cable. b. Non-OBD II Vehicle Cable Connection three possible conditions for Non-OBD II Vehicle Cable Connection: 1) DLC connection supplies both communication and power; 2) DLC connection supplies communication, and power is to be supplied via cigarette lighter connection;
  5. 5. 3) DLC connection supplies communication, and power is to be supplied through cable connection to vehicle battery. -Condition 1 Requirements: the vehicle-specific OBD I adapter; the 15-pin main cable; Steps: 1. Locate the required OBD I adapter and connect the adapter's 15-pin adapter to the cable's 15-pin male adapter. 2. Connect the cable's 15-pin female adapter to the DB15 port on the top of the scan tool. Finger tighten the connecting screws. 3. Connect the main cable's OBD I adapter into the vehicle's DLC.
  6. 6. -Condition 2 If the DLC connection does not supply power to the scan tool, connection to the cigarette lighter receptacle will be needed. Requirement: Clipper cable;
  7. 7. Steps: 1. Connect the clipper cable with the scan tool. 2. Connect the cable's power plug into the vehicle's cigarette lighter receptacle.
  8. 8. NOTE: The vehicle's DLC is not always located under the dash as shown above. NOTE: Some adapters may have more than one adapter or may have test leads instead of an adapter. Whatever the case, make the required connections to the vehicle's DLC. -Condition 3 If the clipper cable connection does not provide power either, connection to the vehicle's battery is necessary. Requirement: cigarette lighter; clipper cable;
  9. 9. Steps: 1. Connect the cigarette lighter to the clipper cable. 2. Connect the clipper cable to the vehicle's battery. NOTE: The vehicle's battery is usually located beside the engine. NOTE: Please connect the red clipper to the anode and the black clipper to
  10. 10. the cathode. WARNING: The clippers might be hot after use. Be careful not to be burnt. You can conveniently obtain power supply through power adapter connection to the scan tool if any power socket is within reach. HKSC39-B Autel MaxiDAS DS708 http://www.wobd2.com/wholesale/autel-maxidas-ds708-1213.html

×