Respiratory Protection: Use NIOSH approved respirator when TLV is exceeded. Read more information please visit here.. http://www.armsmag.com/lifting-magnets.htm

1. RB-50 Cup Assembly Specifications
Part Number – 62003
Overall Diameter OD – 2.030”
Overall Height T – 0.313”
Cup Hole Diameter ID - 0.188”
Magnet Hole Diameter MD – 0.866”
Net Weight – 0.156 lb
Coating – Chrome plated
Working Temperature – 0°F - 176°F
Max. Break Off – 35 lb tested at a ½” thick,
clean ground mild steel plate.
RoHS – In Compliance

3. SAFETY DATA SHEET
SECTION 1 - IDENTIFICATION
Product Name: Ceramic (Ferrite) Magnet
Chemical Name: Strontium Iron Oxide,
SrFe2O3
SECTION 2 – HAZARD
IDENTIFICATION
HMIS Rating [0 (Low or none); 1 (Slight); 2
(Moderate); 3 (Serious); 4 (Severe)]:
Health: 1; Flammability: 1; Instability: 0;
Special Hazards: None

4. SECTION 3 – COMPOSITION ON INGREDIENTS

5. SECTION 4 – FIRST-AID MEASURES
Respiratory Protection: Use NIOSH approved
respirator when TLV is exceeded.
Eye Protection: Use safety glasses or goggles
when handling magnets.
Skin Protection: Protective gloves are
recommended when handling magnetized
part or parts which may have sharp edges.
Ventilation: Use wet machining/grinding
processes and adequate local ventilation to
keep dust levels to minimum.
Work / Hygienic Practices: Use personal
protection equipment when required. Use
good personal hygiene practices. Keep
magnetized parts away from
mechanical/electrical instruments which may
be damaged by high magnetic fields.

6. SECTION 5 – FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS: Material is not flammable Flash Point: N/A
Lower Flammability Limit (LFL): N/A Upper
Flammability Limit (UFL): N/A
Extinguishing Media: N/A
Special Fire Fighting Procedures: None. Material is not a fire hazard.
Unusual Fire and Explosion Hazard(s): Material will not ignite or explode

7. SECTION 6 – ACCIDENTAL RELEASE MEASURES
Spill Procedure: Sweep up dust and
store in water slurry or sealed
containers utilizing inert
atmosphere such as argon or
nitrogen to prevent spontaneous
combustion.

8. SECTION 7 – HANDLING AND STORAGE
WARNING - CERAMIC MAGNETS ARE
EXTREMELY POWERFUL!
They have very strong magnetic forces
which make them attract to other
magnets and other ferromagnetic
materials such as iron or steel. HANDLE
WITH EXTREME CAUTION! Material is
brittle and may chip if not handled with
care.

9. SECTION 8 – EXPOSURE CONTROLS/PERSONAL PROTECTION
Health Hazards (Acute & Chronic): No Known
health hazards. Not listed as carcinogen or
potential carcinogen.
Emergency and First Aid Procedures:
Primary route of entry: Inhalation of generated
airborne dusts. Any long-term exposure to dusts
exceeding recommended TLV levels may result in
irritation to upper respiratory tract.
Skin: Brush off powders and wash well with soap
and water.
Eyes: Dust in eyes may cause irritation. Flush with
running water for 15 minutes.
Use good personal hygiene. Avoid ingestion of
dusts by not eating, drinking or smoking in the
areas where dusts are generated.

10. SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES
Boiling Point: N/A Vapor Pressure: (mm Hg.) N/A
Vapor Density: (air = 1) N/A Specific Gravity: (water = 1) 4.9-5.1
Melting Point: Above 1315oC (2400oF) Evaporation Rate: N/A
Odor: No odor Solubility in Water: Not soluble
Appearance: Metallic dark gray pH: Neutral

11. SECTION 10 – STABILITY AND REACTIVITY
Stability: Stable, no known incompatibilities
Conditions to Avoid: Avoid exposure of powdered
magnet material to air, oxygen or halogenated
hydrocarbons, and to elevated temperatures
above 150oC.
Incompatibility (Materials to Avoid): Fine powders
are incompatible with air, oxygen, halogentated
hydrocarbons and strong oxidizers.
Fine powders or dusts generated by dry grinding or
machining may lead to explosive hazard. Control
dust levels by applying wet machining process,
local exhaust ventilation and good housekeeping.

12. SECTION 11 – TOXICOLOGICAL INFORMATION
N/A
SECTION 12 – ECOLOGICAL INFORMATION
N/A
SECTION 13 – DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose in accordance with federal, state, and local
regulations.
SECTION 14 – TRANSPORTATION INFORMATION
Proper Transportation Name: Class 60, Ceramic Magnets
SECTION 15 – REGULATORY INFORMATION
N/A
SECTION 16 – OTHER INFORMATION
N/A

13. The above information is believed
to be accurate but does not
implicate to be all-inclusive and
shall be used only as a guide.
Armstrong Magnetics, Inc. shall not
be held liable for any damage
resulting from handling or from
contact with the above product.

14. Lifting Magnets
There are three sorts of lifting magnets
technologies: permanent magnetic,
electro-magnetic and electro-perpetual
magnets. The permanent lifting magnets
utilize safeguard, permanent magnets,
however they don't have a variable
holding power ability, which limits both
their load limits and the assortment of
utilizations they are most appropriate for.

15. Armstrong Magnetics
Address:700 Sunset Pond Lane, Suite #4
Bellingham, WA 98226
Tel : (360) 647 - 8438
Toll-Free : (800) 965 - 4968
Fax : (360) 539 -1850
E-mail : sales@armsmag.com
Website : www.armsmag.com