Having your dryer is a good way to keep the appliance operating successfully and keeps away from the risk of fire or water damage to your home. Luckily, installing a dryer vent is simple to do.

1. 1/3
The Proper Dryer Vent Installation Guide
articleecho.com/the-proper-dryer-vent-installation-guide
Having your dryer is a good way to keep the appliance operating successfully and keeps
away from the risk of fire or water damage to your home. Luckily, installing a dryer vent is
simple to do. Developed in 19th-century England, the first technologized clothes dryers
were entering barrels that rotated over flames. These days, machines are not different,
partially in principle, with heated air blown through a tumbler. But where does the air go
when it has absorbed moisture from your shirts, socks, and hand towels? If you have
operated past a modern-day Laundromat, then you before know: For a dryer to use
effectively and safely, it is essential to vent to the outside. Proper Dryer vent
installation starts with a decision. By what route will the duct pass from your appliance
to the exterior of your home? The shorter way is, the better.
Nowadays, homeowners have shared it for use in metal tubing or flexible vinyl in
installation. However, the crinkled design of these ducts, however, leads to a fire risk:
shortly, they trap lint.
Due to this reason, experts now preferably suggest using semi-rigid or rigid pipes, which
can be found quickly and bought inexpensively in the diameter suitable for your appliance
(the correct duct size is four inches for most dryers).
Steps of installation
There are five steps of its installation:
1: Decide the path of the ventilation duct
2: Open up a little, a hole of 4-1/4″ in the exterior wall
3: Fixed the vent cap on the home exterior

2. 2/3
4: For connecting the vent opening to the dryer’s exhaust outlet, cut and join duct sections
5: Test your installation.
1: Decide the path of the ventilation duct:
The shortest possible route is the straight path, but not consistently applied. If your dryer
is present in the basement, the pipe needs to make at least one turn. To complex matters,
the total length of the pipe should not increase than 25 feet—and that is for a straight
shot. Maximum from that pipe, take off two and a half feet for 45-degree ones and five
feet for 90-degree bends.
2: Open up a little, a hole of 4-1/4″ in the exterior wall:
Now comes the most challenging part of proper installation, keeping a hole in the outer
wall. In most cases, the spot must be four and a quarter inches broad (for confirmation,
ask the instructions given by the manufacturer). Mainly for this process recommended
drilling a sample hole first, then going outside to check its position.
If there is no block, and you are boring through wood, move to outfit your drill with a
hole-saw fitting. To perforate plaster or material, it is easier to use a stonework bit to drill
multiple holes around the boundary of the desired opening before manually skinning out
its interior.
3: Fixed the vent cap on the home exterior:
Install the vent cap opposite the side of your house. And sure that it is a fixed pipe
attached through the wall hole you have done. Set the cap with the required screws, and
do not forget to block around the borders for protection against the components. Then,
come to the inner side, attach the vent cap pipe to the dryer duct (the curve needed may
be 90 degrees), and fix the connection with a pipe clamp.
4: For connecting the vent opening to the dryer’s exhaust outlet, cut and
join duct sections:
Having moved the dryer into the wanted place in your laundry room, measure the
distance from the back of the machine to the vent opening, accounting for all the
necessary turns in the passage. With a pair of shears, begin to cut the tubing to the length
of the measured distance. If you are connected to more than one length of tubing,
strengthen all joints with foil tape. When attaching the tubing to your dryer, be sure to
secure the connection employing a pipe clamp.
5: Test your installation:
At this point, it is essential to make sure your vent installation has been vital. Switch on
the dryer, and go outside to check the vent cap: It should be absorbing warm air. If it is
not, go back indoors to analyze your ductwork. The most common explanation is that one
of the connections has not been made.

3. 3/3
Be sure that for your dryer to keep operating at maximum planning, you must accurately
vacuum inside the vent system, as lint has an obstinate way of surviving, even when there
are no ridges in which it can enter.
Why Need Correct Installation:
When washing clothes and keeping them in the dryer, all the water in the clothes needs to
be evaporated off through your vent. Laundry keeps in the dryer. A gas burner or
electrical appliance heats up, passing hot air from the clothes and out via such a duct to
the outside. To maintain proper drying efficiency, the vent should be cleaned and
installed correctly. Not adequate installation can tend to longer drying times, initial
breakdown of the dryer, increased energy costs (from running the dryer various times to
dry each load), and in the wrong case, a dryer fire.
For Prevention from future problems, keep proper dryer
installation:
It is suggested that every two years, preservation should take out for all vents within your
home or business. HVAC cleaning in Smyrna, GA, keeps it safe, and the electricity
bills also decrease. Proper ductwork system installation can save hundreds of dollars for a
homeowner in energy expenses every year and also less the following risks or result in the
following benefits:
Clothes drying times decreased
Less dryer repair costs because of a stressed dryer unit
Rust, gaseous toxins, and molds are not released into your home or office
Decrease danger of a damaging dryer fire that could result in loss of personal
property or home damage
There are a lot of thoughts needed when correctly installing a dryer ventilation route. It
helps in installation and dryer vent cleaning in Smyrna, GA.