Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Thunderbike Triumph Speedmaster/America Mufflers Fitting Instructions

471 views

Published on

Instructions for fitting Thunderbike mufflers to the Triumph Speedmaster or America

Published in: Automotive
  • Was a little hesitant about using ⇒⇒⇒WRITE-MY-PAPER.net ⇐⇐⇐ at first, but am very happy that I did. The writer was able to write my paper by the deadline and it was very well written. So guys don’t hesitate to use it.
       Reply 
    Are you sure you want to  Yes  No
    Your message goes here
  • Be the first to like this

Thunderbike Triumph Speedmaster/America Mufflers Fitting Instructions

  1. 1. THUNDERBIKE SPORTS MUFFLERS TRIUMPH SPEEDMASTER/ AMERICA PLEASE NOTE: READ INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING TO ASSEMBLE.YOU MAY REQUIRE:A GAS WELDING TORCH, A SMALL AMOUNT OF BLACK PAINT. A SHORT NARROWFLAT-BLADE SCREWDRIVER.PARTS LISTL/H Muffler (1)R/H Muffler (1)M8 Stainless Plain Washers (4)M8x 20 Stainless Bolts (4)INSTRUCTIONS 1. Slacken 13mm front muffler clamp 2. Remove 2x 12mm rear footrest mount plate bolts and remove plate. Rotate muffler and slide rearwards to remove. Note the position of the mounting rubbers and washers between the footrest plate and the muffler bracket 3. REMOVAL OF SILENCER MOUNTING BRACKETS: Firstly undo the 4 Allen head bolts which fasten the mount to the silencer if this results in the bolt turning but not releasing then see number 4.thru 5 4. If you find the Allen bolts turn but will not release At this point you will need to use a gas-welding torch. If you are unfamiliar in the use of these, or do not have access to one, you will need to employ the services of a suitably equipped person competent in it’s use. Heat the 2x Allen bolt heads gently until glowing an orange colour, being careful not to melt the bolt head in any way. Keep them at this temperature for approx. 45-60 seconds. This is very important to allow the heavy-duty thread-locking agent applied by Triumph to release its hold. Allow the bolts to cool and remove them. If they are still stiff in any way, repeat the process. 5. Paint the heat damaged area on bracket; this will only be small area and should be painted at this time. 6. Refit bolts (Or the Stainless bolts supplied) to bracket first, then a plain washer to each bolt, and then tighten both. 7. Fit original front clamp to the muffler and coat down-pipe and inside of muffler mating area with a suitable exhaust sealant or gasket silicone. 8. Slide muffler into position and secure using the reverse of the removal process, taking care to ensure the correct fitment of the rubber mounts and washers at the footrest plate mount area. 9. Repeat process on the other muffler. 10. At this point, on carb models, we recommend adjusting the idle mixture screw. This can be done very easily with a short screwdriver. Note the original position of the screw then turn it anti-clockwise by one turn when viewed from underneath. The screw is located in the lower front area of the carburetor in the round extension which projects downwards, beside the electrical connections. ( Note on 2005 and later bikes a special tool is required to adjust the idle mixture screw) 11. Start bike and idle to allow sealant to cure. 12. Ride off into the distance with a big smile on your face. Feel the power and enjoy the sound!!! Thunderbike Engineering Ltd 2/46A Muritai Street, Tahunanui, Nelson 7011 New Zealand Tel: +64 (0)3 548 5787 parts@thunderbike.co.nz www.thunderbike.co.nz

×