1. Plastopia DFM ReportPlastopia DFM Report
Project Name 503-1
(Side Attachment)
Prepared by Peter Fong
Date Nov-06-2015
Version 1

2. Plastopia Mould # PM503-1-1 Shrinkage 1.005
Tool Type
2 Plate
Customer Mold # N.A
General Wall
Thickness
2.0 mm Gate Type Edge gate
Part Name
SIDE
ATTACHMENT
LH
Cavity No. 1+1 Qty of Sliders 0
Drawing Name
WM03_side_att
echment_rh.X_T
Cav + Cor Steel WY 718 Qty of Lifters 6
Part Material ABS Mold base Steel S50C/CI3535 Press size 80 T
Part Weight 6.5 g Feed System Cold runner
131.56
50.496
11.30
General Information
OK/ NG Approved by Date

3. 350.0m
m
350.0m
m
200.0m
m 200.0m
m
Mold Size & Layout
OK/ NG Approved by Date

4. Draft Angle Analysis
OK/ NG Approved by Date
New part is ok for draft angles.
No changes needed.
New part is ok for draft angles.
No changes needed.

5. CAVITY
CORE
Cavity
Core
Parting Line 分型线
OK/ NG Approved by Date
Please confirm the parting line-
see the red line.
Please confirm the parting line-
see the red line.

6. 1.50m
m
4.0mm
5.0mm1.20m
m
Part Center
Gate Location 进胶口
OK/ NG Approved by Date
Edge gate →Sub gate Please confirmEdge gate →Sub gate Please confirm

7. A
A
A-A
0.50m
m
3.80m
m
Wall thickness Analysis
OK/ NG Approved by Date
The thickness is NOT even: 0.5~3.8 mm.
Red surface will have sink marks. We
suggest to change the part. This can NOT
be adjusted by injection condition. Specific
solution see next page:
The thickness is NOT even: 0.5~3.8 mm.
Red surface will have sink marks. We
suggest to change the part. This can NOT
be adjusted by injection condition. Specific
solution see next page:

8. Thickness Suggestion-1
OK/ NG Approved by Date
After change, sink marks are reduced
much obviously from the software. We
will also adjust the injection condition
during molding to avoid sink marks.
After change, sink marks are reduced
much obviously from the software. We
will also adjust the injection condition
during molding to avoid sink marks.
fore
er
Red surface changed to ribs, see
below and attached 3d for approval.
Red surface changed to ribs, see
below and attached 3d for approval.

9. Thickness Suggestion-2
OK/ NG Approved by Date
Yellow surface here was deform
both STP and X_T. Please chec
re-send the drawing in differen
format.
Yellow surface here was deform
both STP and X_T. Please check
re-send the drawing in differen
format.
Yellow surface here was corrected
by us. See attached 3d for approval.
Yellow surface here was corrected
by us. See attached 3d for approval.

10. Lift1
Lift2
Lift3
Lift1
Lift2Lift3
Lifters
OK/ NG Approved by Date
The red lines are split lines caused
by the lifters.
The red lines are split lines caused
by the lifters.

11. Ejector Pins ¢4 3 pcs
Ejector Pins ¢3 2 pcs
Stepped Ejector Pins ¢2.5 1 pcs
Ejector Pins ¢6 3 pcs
Lifter
Ejector Pins
Lifter Lifter
There are ejector pin marks left on
the part, please confirm.
There are ejector pin marks left on
the part, please confirm.
OK/ NG Approved by Date

12. Surface Finish
OK/ NG Approved by Date
All surfaces→ Texture VDI32All surfaces→ Texture VDI32