Caterpillar Cat 422F2 Backhoe Loader (Prefix LYF) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
422F2 Backhoe Loader

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 422F2 BACKHOE LOADER LYF
Configuration: 422F2 Side Shift Backhoe Loader LYF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
422F2, 427F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Powertrain
Media Number -UENR3743-01 Publication Date -01/06/2015 Date Updated -05/06/2018
i07435290
Transmission (Direct Drive) - Assemble
SMCS - 3030-016-DD; 3066-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 395-1590 Lifting Eye Assembly 1
B 422-5471 Lifting Eye Assembly 2
C 4C-3652 Spring Compressor 1
D 1P-1859 Retaining Ring Pliers 1
H 137-8102 Spring Compressor 1
J 1P-0510 Driver Gp 1
K - Loctite High Flex Gasket Maker -
L - Loctite Retaining Compound 648(1)
-
M - Loctite Retaining Compound 243(2)
-
N 8T-5096 Dial Indicator Gp 1
(1)
Loctite 649 is acceptable.
(2)
Loctite 242 is acceptable.
Note: The transmission will be assembled in major components. The major components will then
be assembled.
Note: Apply a light film of clean transmission oil to all components before assembly.
1/36
422F2 Side Shift Backhoe Loader LYF00001-UP (MACHINE) POWERED BY C4.4 ...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Transmission case
Illustration 1 g03831934
1. Install breather (168).
2. Use Tooling (J) to install lip seal (162) into case (36). Dimension (X) is the depth to install
lip seal (162) into case (36). Dimension (X) is 4.00 ± 0.25 mm (0.157 ± 0.010 inch).
2/36
2019/12/2

Note: Install the shims behind each bearing cup that was recorded on the disassembly
procedure.
3. Install bearing cup (159), bearing cup (160), bearing cup (161), bearing cup (163), and
bearing cup (164) into case (36).
4. Install temperature sensor (158). Tighten temperature sensor (158) to a torque of
20 ± 3 N·m (177 ± 27 lb in).
5. Install O-ring seals (156) and (157) onto relief valve (150).
3/36
2019/12/2

6. Install O-ring seals (153), (154), and (155) onto relief valve (148).
7. Install strainer (152) and bolts (151).
8. Install relief valve (148). Tighten relief valve (148) to a torque 46 to 54 N·m (34 to 40 lb ft).
4/36
2019/12/2

9. Install relief valve (150). Tighten relief valve (150) to a torque 23 to 30 N·m
(204 to 266 lb in).
10. Use Tooling (J) to install lip seal (149) into the case. Dimension (Y) is the depth to install
lip seal (149) into the case. Dimension (Y) is 3.00 ± 0.25 mm (0.118 ± 0.010 inch).
11. Install pump (147), the O-ring seal, and bolts (146). Tighten bolts (146) to a torque of
18 to 31 N·m (159 to 274 lb in).
12. Apply Tooling (K) to the case and install plate (145) and bolts (144).
13. Apply Tooling (K) to the case and install torque converter housing (142) and bolts (143).
14. Install bearing cup (136), bearing cup (137), bearing cup (138), bearing cup (139), bearing
cup (140), and O-ring seals (141) into the case.
Direct Drive, Input Shaft
5/36
2019/12/2

1. Apply Tooling (L) to the input shaft and install gear (135). Raise temperature of bearing
cone (134) and install bearing cone (134) on the input shaft. Install sealing ring (133) onto
the input shaft.
2. Install O-ring seals (131) and (132) onto piston (130).
3. Install piston (130).
6/36
2019/12/2

4. Install sleeve (129).
Personal injury can result from being struck by parts propelled by a
released spring force.
7/36
2019/12/2

Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (128) and retainer (127). Use Tooling (H) and a suitable press to compress
spring (128). Use Tooling (D) to install retaining ring (126).
6. Install clutch pack (124) and thrust washer (125).
7. Install end plate (123) and retaining ring (122).
8/36
2019/12/2

8. Install thrust bearing (120) and needle bearing (121).
9. Install gear (119) and thrust washer (118).
10. Use Tooling (D) to install retaining ring (117). Install retaining ring (117).
9/36
2019/12/2

11. Raise temperature of bearing cone (116) and install on the input shaft.
12. Install sealing rings (115).
13. Install input shaft (114).
Direct Drive, Reverse Shaft
10/36
422F2 Side Shift Backhoe Loader LYF00001-UP (MACHINE) POWERED BY C4....
2019/12/2

1. Install O-ring seals (112) and (113).
2. Install piston (111).
3. Install sleeve (110).
11/36
2019/12/2

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install spring (109) and retainer (108). Use Tooling (H) and a suitable press to compress
spring (109). Use Tooling (D) to install retaining ring (107).
5. Install clutch pack (106).
12/36
2019/12/2

6. Install end plate (105) and retaining ring (104).
7. Install thrust washer (103) and needle bearing (102) onto the reverse shaft.
8. Install gear (99) and bearing (101) onto the reverse shaft.
13/36
2019/12/2

9. Install thrust washer (100) onto the reverse shaft.
10. Raise temperature of bearing cone (98) and install bearing cone (98) onto the reverse shaft.
11. Install ring seals (97) onto the reverse shaft.
12. Install reverse shaft (96).
Direct Drive Shaft
14/36
2019/12/2

1. Raise temperature of bearing cone (95) and install bearing cone (95) onto the direct drive
shaft.
2. Raise temperature of bearing cone (94) and install bearing cone (94) onto the direct drive
shaft.
3. Install direct drive shaft (93).
Direct Drive, Rear Output Shaft
15/36
2019/12/2

1. Install bearing (92) and bearing spacer (91).
2. Install gear (88) and sleeve (87) onto the rear output shaft.
3. Raise temperature of sleeve (86). Install sleeve (86) and shims (83) onto the rear output
shaft.
4. Install bearing spacer (85) and bearing (84) onto the rear output shaft.
16/36
2019/12/2

5. Install synchronizer assembly (82) and shims (81) onto the rear output shaft.
6. Install gear (90) onto the rear output shaft.
7. Apply Tooling (L) to the splines of the rear output shaft and install gear (89).
8. Raise temperature of cone bearing (80) and install cone bearing (80) onto the rear output
shaft.
17/36
2019/12/2

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

9. Install needle bearings (79) and (78) onto the rear output shaft.
10. Install gear (77) onto the rear output shaft.
11. Install sleeve (76) onto the rear output shaft.
12. Install synchronizer assembly (75) onto the rear output shaft.
18/36
2019/12/2

Caterpillar Cat 422F2 Backhoe Loader (Prefix LYF) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 422F2 Backhoe Loader (Prefix LYF) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 422F2 Backhoe Loader (Prefix LYF) Service Repair Manual Instant Download.pdf (9)

More from 8foskkdjdkdm3e

More from 8foskkdjdkdm3e (20)

Recently uploaded

Recently uploaded (19)

Caterpillar Cat 422F2 Backhoe Loader (Prefix LYF) Service Repair Manual Instant Download.pdf