How to Configure an SNMP-enabled UPS

285
-1

Published on

How to Configure an SNMP-enabled UPS. For more info go to: http://www.open-e.com

Published in: Technology, Business
0 Comments
0 Likes
Statistics
Notes
  • Be the first to comment

  • Be the first to like this

No Downloads
Views
Total Views
285
On Slideshare
0
From Embeds
0
Number of Embeds
1
Actions
Shares
0
Downloads
2
Comments
0
Likes
0
Embeds 0
No embeds

No notes for slide

How to Configure an SNMP-enabled UPS

  1. 1. How to configure an SNMP-enabled Uninterruptable Power Supply with DSS V6Software Version: DSS ver. 6.00 up10Presentation updated: September 2010
  2. 2. How to configure an SNMP-enabled UPS Example configuration with UPS ONLINE model XANTO S1500Please read your UPS Web/SNMPManager user manual andconfigure the IP address of thenetwork adapter.In this presentation, the UPSnetwork adapter IP address will beset to 192.168.0.251. www.open-e.com 2
  3. 3. How to configure an SNMP-enabled UPS TO CONFIGURE THE SNMP – ENABLED UPS, THE FOLLOWING STEPS NEED TO BE PERFORMED: 1. Configure the UPS Network Adapter 2. Configuring UPS support in DSS V6 3. Testing Online and On-Battery modeNOTE:You must be using DSS V6 up10 build 3719 or newer. www.open-e.com 3
  4. 4. How to configure an SNMP-enabled UPS 1. Configure the UPS Network Adapter Enter the WebGUI of the UPS network adapter. In the “UPS Model & System” section, set the UPS Model parameter to XANTO S1500. www.open-e.com 4
  5. 5. How to configure an SNMP-enabled UPS 1. Configure the UPS Network Adapter Next, go to the “Network & Security” section and set the SNMP Trap Version parameter to 1. www.open-e.com 5
  6. 6. How to configure an SNMP-enabled UPS 1. Configure the UPS Network Adapter Next, go to the “SNMP” section and enter the IP address of the DSS V6 server (you can enter more than one). Please enter public into the Community fields. In order to confirm the settings click the Apply button, then select „Save Configuration” in the left menu. www.open-e.com 6
  7. 7. How to configure an SNMP-enabled UPS 2. Configuring UPS support in DSS V6 Data Storage Software (DSS) IP Address:192.168.0.220Enter the WebGUI of the DSSserver, go to the „SETUP” menuand select „hardware”. In UPSsettings, check the Use UPS boxand select MGE as vendor. Next,select UM-Link (SNMP) as UPSmodel and enter its IP address intothe SNMP Host Agent Domainfield. In order to confirm thesettings click the apply button. www.open-e.com 7
  8. 8. How to configure an SNMP-enabled UPS 3. Testing Online and On Battery mode Data Storage Software (DSS) IP Address:192.168.0.220Go to the „STATUS” menu andchoose „hardware”. If the UPS isonline and properly detected andconfigured, the Status parameter inUPS status will show OL. www.open-e.com 8
  9. 9. How to configure an SNMP-enabled UPS 3. Testing Online and On Battery mode Data Storage Software (DSS) IP Address:192.168.0.220In order to test the On-Batterymode, remove the main power cordfrom the UPS. Now, the Statusparameter in UPS status shouldshow OB (refresh the GUI page inyour browser if needed). Then,reconnect the main power cordback to the UPS and refresh theGUI page – the Status parametershould show OL again.NOTE:An event viewer prompt with “onbattery” messages is shown here. www.open-e.com 9
  10. 10. Thank you!Follow Open-E: www.open-e.com 10
  1. A particular slide catching your eye?

    Clipping is a handy way to collect important slides you want to go back to later.

×