1. TMTMTMTM222266662222(28064280642806428064) InInInIndoordoordoordoor RemoteRemoteRemoteRemote PowerPowerPowerPower SocketSocketSocketSocket
RemoteControlRemoteControlRemoteControlRemoteControl SystemSystemSystemSystem
OutdoorOutdoorOutdoorOutdoor WirelessWirelessWirelessWireless RemoteRemoteRemoteRemote ControlControlControlControl withwithwithwith 101010100ft.0ft.0ft.0ft. ((((30303030m)m)m)m) RangeRangeRangeRange
RATING:RATING:RATING:RATING: 125VAC/60Hz/8A/1000W125VAC/60Hz/8A/1000W125VAC/60Hz/8A/1000W125VAC/60Hz/8A/1000W RESISTIVERESISTIVERESISTIVERESISTIVE &&&& TUNGSTENTUNGSTENTUNGSTENTUNGSTEN
TechnicalTechnicalTechnicalTechnical SpecificationsSpecificationsSpecificationsSpecifications
1. Working voltage: 125VAC/60Hz
2. Rating current: 8A
3. Rating power: 1000W
4.Working temperature: -25~40℃
5. Working frequency: 315Mhz/433.92Mhz,
customized frequency is available
ClearClearClearClear CodeCodeCodeCode
1.Turn off the socket output.
2.Press the learning code button about 10 second ,during that time the green lights will flicker
several times,then you will hear ‘ka” twice,after 2 second later,green light will turn off,you clear
code successfully.
LearningLearningLearningLearning CodeCodeCodeCode
1.Press the learning button about 2 second,green light will flicker.
2.You can press the controller ,then hear “ka”,learning code successfully.
2. RemoteRemoteRemoteRemote SocketSocketSocketSocket OOOOperationperationperationperation IIIInstructionnstructionnstructionnstructionssss
1. Put the power input end of remote socket into a grounded 3-prong outlet, Be sure the outlet is
GFCI approved. Double confirm that connection is reliable.
2. The indicating LED of remote socket will be lighting up after successful connection, pls
check connection again if not.
3. Put your appliances into the outlets of Socket Base . Be sure that your appliances are powered
ON.
4. Press “ ON” and “ OFF” buttons of remote control to activate the remote socket.
ProductsProductsProductsProducts RemarkRemarkRemarkRemarkssss
1. TM260 has been tested and found to comply with the limits for a CLASS B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
2. There is no guarantee that harmful interference will not occur in a particular installation like
too close to radio or television especially to those operating motors inside some equipments.
3. It is also not encouraged to install 2 sets power sockets of this product within 15 meters,
otherwise it may cause harmful interferences to each other when they are used in the same
time.
4. ChangesChangesChangesChanges orororor modificationsmodificationsmodificationsmodifications havehavehavehave totototo bebebebe handledhandledhandledhandled bybybyby qualifiedqualifiedqualifiedqualified people.people.people.people.
5. KeepKeepKeepKeep itititit awayawayawayaway fromfromfromfrom children.children.children.children.
WARNINGWARNINGWARNINGWARNING ::::
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two condition:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including interference that may
cause undesired operation.
The user manual or instuction manual or unnitententional radiator shall caution the
user user that changes or modifications not expressly approved by the party
responsible for compliance could void the user authoritv to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
3. installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interferences to radio communication.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interferences to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed
4. Consult the dealer or an experienced radio/ TV technician for help
BATTERYBATTERYBATTERYBATTERY INFORMATIONINFORMATIONINFORMATIONINFORMATION ANDANDANDAND REPLACEMENTREPLACEMENTREPLACEMENTREPLACEMENT::::
The Remote Control uses a volt CR2032 lithium battery. To replace, Slide off the
battery cover on the back off the Transmitter.Lnsert a new CR2032 lithium battery,
making sure to match up the +and –polarity markings. To test, press the ON or OFF
buttons to make sure the LED lights up. Slide the cover back in.Do not dispose of
batteries in fire. Batteries may explode or leak.
CARTION:
1. Only use the batteries specified and be sure to match the +and –polarity markings.
2. DO not mix old batteries and new batteries or standard (carbon-zinc) with alkaline
batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be used for a long time.
5.5.5.5. Do not dispose of batteries in fire . Batteries may explode or leak .As with all
small items, these batteries should be kept away from children. If swallowed, seek
medical attention immediately.