Apply smart switchable privacy film to the installedwindows

APPLY SMART SWITCHABLE PRIVACY FILM TO THE
INSTALLED WINDOWS

This is the new innovative way to apply the smart privacy film to the installed windows. And please remember to
read the notes in the end of the document.

1.
Tools and materials:
Scraper, glove, clean tissue, ethanol(70%-90%), special UV glue, Burette, Soft roll.

2.
Use the scraper and ethanol to clean the glass

ALL RIGHT RESERVED BY
CNC INTERLAYER TECH
SUPPLY SMART PRIVACY FILM/EVA INTERLAYER FILM
WEB: WWW.CNCNEXT.COM / WWW.EVAFILMS.COM
MAIL: CNC@CNCNEXT.COM / EVA@EVAFILMS.COM / BENEXT77@HOTMAIL.COM

3.
Use tape to put the smart switchalbe film on the window.

4.
Make sure that smart switchalbe film is not powered on,meaning the smart swichable film is on milky white, use
the soft roll to roll the smart switchalbe film to check the dust on the windows or smart switchalbe film.

CNC INTERLAYER TECH

5.
Turn on the smart switchable film, which meaning the smart privacy film is transparent, use the soft roll to roll the
smart privacy film to clean the dust.

6.
You can use tape to move the dust.

CNC INTERLAYER TECH

7.
Use the clear tape to seal the right size, left side and bottom side of the smart glass to the window.

8.
Use Burette to drop UV glue on the top size of the smart glass film.

CNC INTERLAYER TECH

9.
The UV glue will spread on the bottom of the smart glass film.

10.
Use soft roll to roll the smart film onto the windows from down to up. Carefully not left bubbles between the
smart glass film and the windows.

CNC INTERLAYER TECH

11.
Softly and slowly rolling will help to avoid the bubbles.

12.
Even push will help tp well-distribute the glue and make the smart film in good balance to the window.

CNC INTERLAYER TECH

13.
The bubbles is each to happen between the push, so the 2/3 of the width of the soft roll is the best for the new
push.

14.
Squeeze the bubbles right to the edges.

CNC INTERLAYER TECH

15.
Double check that no small bubbles left on the corner.

16.
Clear the smart privacy film with ethanol after you make sure no bubbles left.

CNC INTERLAYER TECH

17.
Double roll the smart film make sure the smart film is parallel to the windows and the glue is well-distributed.

18.
Clean the smart film with ethanol again.

CNC INTERLAYER TECH

19.
Soldering the wire to the connecting tap on the smart film.

20.
Use black tape to cover the pose (the connecting tap and the wires)

CNC INTERLAYER TECH

21.
It takes sometime for the UV glue to solidify.

22.
Now, Congratulations, you have done a great job. The smart glass is successfully installed.

CNC INTERLAYER TECH

Notes of Installation of the Smart Glass Film:
1.
The special Sunlight Glue only require sunlight to solidify.
2.
Before the the Sunlight Glue is solidified, you can re-do the procedure to clean dust or eliminate bubbles if you
find them after installation.
3.
The solidifying may finish in several minutes in great sunlight or takes a day in the indoor environment, So if you
need long time to install smart glass(Suppose it's your first time), you can use a black paper to cover the other side
of the window to avoid the sunlight.
4.
In other words, you need solidifying finish as soon as possible, you can use UV light to fasten the solidifying.

CNC INTERLAYER TECH

CNC INTERLAYER TECH

Apply smart switchable privacy film to the installedwindows

Recommended

Recommended

More Related Content

More from Eva Glass

More from Eva Glass (20)

Recently uploaded

Recently uploaded (20)

Apply smart switchable privacy film to the installedwindows