Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt01618 03227)

Service Repair Manual
Model
428D BACKHOE LOADER

Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428D BACKHOE LOADER BMT
Configuration: 428D Backhoe Loader BMT01618-03227 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Machine
Systems
Media Number -RENR3585-11 Publication Date -01/09/2009 Date Updated -28/09/2009
i01429122
Steering Metering Pump - Remove
SMCS - 4312-011
Removal Procedure
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4428D Backhoe Loader BMT01618-03227 (MACHINE) POWERED BY 3054 Engine(...
2019/10/8https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00748631
1. Remove torx screws (1) and cover (2) .
2. Remove torx screws (3) and cover (4) .

3. Remove torx screws (5) and plate (6) .
4. Remove two nuts (7) and two bolts (8). Position steering column (9) on the floor of the cab.
5. Disconnect two connectors (10) .

6. Disconnect five lines (11) from metering valve (12) .
7. Remove four allen head screws (13) from metering valve (12) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 8 21:51:19 UTC+0800 2019

Shutdown SIS
Previous Screen
Systems
i01473776
Steering Metering Pump - Disassemble
SMCS - 4312-015
Disassembly Procedure
Start By:
A. Remove the steering metering pump. Refer to Disassembly and Assembly, "Steering
Metering Pump - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.

Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes.
Steering metering pump
1. Remove seven bolts (1) .
2. Remove end cap (2) .

3. Remove O-ring seal (3) .
4. Remove housing (4) .

(6) Spacer plate
(7) Star
(8) Drive
(9) Drive spacer
6. Remove drive spacer (9), drive (8), star (7), and spacer plate (6) from the housing.
8. Remove spool and sleeve assembly (11) .
Note: Do not bind the spool and sleeve assembly in the housing. Rotate the spool and sleeve
assembly slowly in order to remove the assembly from the housing.
Note: During removal, the pin may slide outward from the spool and sleeve assembly which
will lock these parts in the housing. If this occurs, center the pin and continue to remove the
spool and sleeve assembly.

9. Remove pin (12) from the spool and sleeve assembly (11) .
10. Remove spool (13) from the control end of sleeve (14) .

11. Remove centering springs (15) from spool (13) .
Note: The steering metering unit uses six centering springs.
Tapped plug (16) retains the manual steering check valve.
12. Remove tapped plug (16) .
Manual steering check valve
13. Remove roll pin (18) and ball (17) .

Anticavitation valves
14. Remove two roll pins (20) and two balls (19) from the bolt holes by tipping the housing.
(21) Seal
(22) Spacer
(23) Needle bearing
(24) Spacer
15. Remove spacer (24), needle bearing (23), spacer (22), and seal (21) .

16. Pry retaining ring (25) from the housing.
(25) Retaining ring
(26) O-ring seal
(27) Bushing
(28) Dust seal
17. Remove dust seal (28), bushing (27), and O-ring seal (26) .

18. Remove five hydraulic fittings (29) in order to complete disassembly of the steering
metering unit.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 8 21:52:16 UTC+0800 2019

Shutdown SIS
Previous Screen
Systems
i01474281
Steering Metering Pump - Assemble
SMCS - 4312-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.

1. Install five hydraulic fittings (29) .
(25) Retaining ring
(26) O-ring seal
(27) Bushing
(28) Dust seal
2. Install O-ring seal (26), bushing (27), dust seal (28), and retaining ring (25) .
(21) Seal
(22) Spacer
(23) Needle bearing
(24) Spacer
3. Install seal (21), spacer (22), needle bearing (23), and spacer (24) .

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

4. Install centering springs (15) into spool (13) .
Note: The steering metering pump uses six centering springs.
Note: The centering spring notches must face away from the splined end of the spool.
5. Install spool (13) into sleeve (14) .

6. Insert pin (12) through spool and sleeve assembly (11). The pin should be flush with both
sides of the sleeve.
7. Insert spool and sleeve assembly (11) into the housing. Insert the spool and sleeve assembly
until the spool and sleeve assembly are flush with the end of the housing.
Note: Do not insert the spool and sleeve assembly beyond this point. The pin may become
stuck in the discharge groove.
8. Check for free rotation of the spool and sleeve assembly by turning the assembly with
fingertip force at the splined end.

(8) Drive
(12) Pin
(30) Port face
9. Rotate the spool and sleeve assembly until the pin is parallel with port face (30) .
10. Install drive (8).
(6) Spacer plate

(10) O-ring seal
(17) Ball
(18) Roll pin
(19) Ball
(20) Roll pin
11. Install two balls (19) and two roll pins (20) .
12. Install ball (17) and roll pin (18) .
13. Install the tapped plug in order to retain the check valve for manual steering.
14. Install O-ring seal (10) and spacer plate (6) .
Note: Align bolt holes in the spacer plate with the tapped holes in the housing.
(4) Housing
(5) O-ring seal
(7) Star
15. Install O-ring seal (5), and star (7) in gerotor housing (4) .

(4) Housing
(7) Star
(8) Drive
(12) Pin
16. Make a mark (B) on drive (8) parallel to pin (12) .
17. Align star valleys (A) with marked drive (B), pin (C), and port face (D) .
Note: Proper alignment of the star is critical in order to ensure proper operation of the
steering metering pump. The star valleys must align with the pin. Align bolt holes without
disengaging the gerotor from the drive.

Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt01618 03227)

Recommended

Recommended

More Related Content

What's hot

What's hot (8)

Similar to Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt01618 03227)

Similar to Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt01618 03227) (20)

More from ujdfjkkskmem

More from ujdfjkkskmem (16)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 428 d backhoe loader (prefix bmt) service repair manual (bmt01618 03227)