Caterpillar cat 730 articulated truck (prefix 3 t3) service repair manual (3t300001 and up)

Service Repair Manual
Models
730 Articulated Truck

Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730 ARTICULATED TRUCK 3T3
Configuration: 730 Articulated Truck 3T300001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05331988
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7638 Magnetic Holding Tool 18
B
201-4211 Camshaft Pilot 1
201-4212 Camshaft Pilot 1
Start By:
a. Remove the rocker arms and shafts.
b. Remove the front cover.
c. Remove the camshaft position sensor.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel.
1/5730 Articulated Truck 3T300001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01878122
2. Install Tooling (A) in order to support the lifter. Repeat for all the remaining lifters.

3. Remove bolts (1). Remove bolt (2) and idler gear (3) for assembly purposes.
4. Remove tube assembly (6) and hose assembly (5). Remove cover (4).
5. Install Tooling (B) onto the camshaft.

Note: Lubricate Tooling (B) for easier removal of the camshaft. Lubrication also prevents
damaging the camshaft lobes and the camshaft bearings.
6. Use two people to remove camshaft (7). The weight of camshaft (7) and the camshaft gear
is approximately 34 kg (75 lb). Carefully remove camshaft (7) from the engine. Support the
weight of the camshaft during removal.
Note: Rotate the camshaft during removal. This action will prevent the camshaft from
binding in the camshaft bearings.
Installation Procedure
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.

Note: Ensure that camshaft (6) and Tooling (B) are clean. Apply clean engine oil to the lobes and
journals of camshaft (6) and Tooling (B).
Note: During installation of camshaft (6), rotate the camshaft in both directions in order to prevent
binding in the camshaft bearing bores.
1. Install camshaft (6) in the reverse order of removal.
a. Ensure that the timing Marks (X) on the idler gear aligned with the timing marks on
the crankshaft gear and the camshaft drive gear.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 12:26:54 UTC+0800 2019

Shutdown SIS
Previous Screen
i05351535
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
A. Remove the camshaft.
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.

NOTICE
Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove drive gear (1) from camshaft (3) .
3. Remove woodruff key (2) .
1. Install drive gear (1) in the reverse order of removal.
a. Raise the temperature of drive gear (1) to a temperature of 315° C (600° F).
Fri Dec 13 12:27:50 UTC+0800 2019

Shutdown SIS
Previous Screen
i05332615
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
A
201-4214 Receiving Sleeve 1
201-4213 Puller Plate 1
201-4209 Bearing Pilot 1
201-4208 Backup Plate 1
6F-7032 Bolt 1
8M-8778 Taperlock Stud 1
8S-8292 Extension (Short) 2
8S-8293 Extension (Long) 1
B 185-3989 Thread Lubricant 1
Start By:
a. Remove the lifter group.
b. Remove the camshaft.

1. Install Tooling (A). Apply Tooling (B) on the threads.
2. Remove camshaft bearings (1).
Table 2
Required Tools
A
201-4214 Receiving Sleeve 1
201-4213 Puller Plate 1
201-4209 Bearing Pilot 1
201-4208 Backup Plate 1
6F-7032 Bolt 1
8M-8778 Taperlock Stud 1
8S-8292 Extension (Short) 2
8S-8293 Extension (Long) 1

1. Position new camshaft bearing (1) in Tooling (A) and install the bearing from the rear to the
front of the engine.
2. The camshaft bearings are installed with Tooling (A). Measure the depth of the camshaft
bearings from the front face of the cylinder block to the following distances:
a. Dimension (A) is 36.50 mm (1.437 inch).
b. Dimension (B) is 192.50 mm (7.579 inch).
c. Dimension (C) is 348.50 mm (13.720 inch).
d. Dimension (D) is 504.50 mm (19.862 inch).

e. Dimension (E) is 660.50 mm (26.004 inch).
f. Dimension (F) is 816.50 mm (32.146 inch).
g. Dimension (G) is 972.50 mm (38.287 inch).
NOTICE
Camshaft bearings must be installed into their correct position. Failure
to do so will result in engine damage.
(2) Bearing joint
(3) Oil hole
(H) Bearing oil hole is located at a 45 degree angle from vertical. All seven bearings have the
same angle.
End By:
a. Install the camshaft.
b. Install the lifter group.
Fri Dec 13 12:28:45 UTC+0800 2019

Shutdown SIS
Previous Screen
i05351536
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
A 4C-9614 Silicone Sealant 1
1. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the
proper draining and filling procedures.
2. Remove bolts (3), stud bolts (2), and the fasteners.
3. Remove clips (4) and (5). Position the harness assembly out of the way.

4. Remove engine oil pan (1). Remove and discard the isolation seal.
5. Remove bolts (7) and (8). Remove suction bell assembly (6) .
6. Remove switch assembly (9) .
7. Remove plugs (10) and (11) .
1. Install engine oil pan (1) in the reverse order of removal.

Note: Ensure that the oil pan and mating surfaces are clean and free of oil.
a. Apply Tooling (A) at four locations marked (A). Tooling (A) should be applied in 4 ±
1 mm (0.16 ± 0.04 inch) diameter beads.
Note: All joints using Tooling (A) must be assembled within 10 minutes of the
application.
b. Tighten plugs (11) to a torque of 90 ± 15 N·m (66 ± 11 lb ft).
c. Tighten plugs (10) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
Torque Sequence
d. Tighten bolts (3) and stud bolts (2) in the above sequence.
Fri Dec 13 12:29:41 UTC+0800 2019

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i06246844
Cylinder Liner - Remove and Install
SMCS - 1216-010
Removal Procedure
Table 1
Required Tools
A 5P-8665 Cylinder Liner Puller Gp 1
Start By:
A. Remove the pistons and the connecting rods.

1. Use Tooling (A) to remove cylinder liner (1) .
2. Remove the O-ring seals from cylinder liner (1) .
Table 2
Required Tools
B 2P-8260 Cylinder Liner Installer 1
C 5P-3975 Rubber Lubricant 1
1. Install the O-ring seals on cylinder liner (1) .
2. Apply Tooling (C) on the O-ring seals.
Note: Refer to Testing and Adjusting, "Cylinder Liner Projection" for more information.
Note: If you are installing a cylinder pack, ensure that the corresponding crankshaft throw is
at bottom center.
3. Use Tooling (B) to install cylinder liner (1) .
End By: Install the pistons and the connecting rods.

Shutdown SIS
Previous Screen
i03554761
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan.
NOTICE
Special care must be taken not to bend the piston cooling jets because
the piston cooling jets are precision aligned with a coolant passage in
the pistons.
There is only one position for each cooling jet. The notch in the bottom
of the piston allows clearance for the piston cooling jet when the piston
is at bottom dead center.

1. Remove bolt (1) and piston cooling jet (2).
1. Install piston cooling jet (2) in reverse order of removal.
a. Tighten bolt (1) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Fri Dec 13 12:31:33 UTC+0800 2019

Caterpillar cat 730 articulated truck (prefix 3 t3) service repair manual (3t300001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (9)

Similar to Caterpillar cat 730 articulated truck (prefix 3 t3) service repair manual (3t300001 and up)

Similar to Caterpillar cat 730 articulated truck (prefix 3 t3) service repair manual (3t300001 and up) (20)

More from ufjjskefksmem

More from ufjjskefksmem (12)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 730 articulated truck (prefix 3 t3) service repair manual (3t300001 and up)