Wellsford Cabinetry Standard Door Styles

1. DOOR STYLE SELECTION GUIDE

2. Thank you for considering Wellsford Cabinetry. This Door Selection Guide will provide useful
information on offering, price level, minimum sizing, and dimensional details for our standard doors.
While we have selected 42 of the most popular doors, others are available to suite specific needs.
Should you be in a position of having to match something particular, please let us know and we will
show you what we can do to fill your requirements.
All doors are available in Red Oak, Soft Maple, Hard Maple, and Cherry. Please refer to the Finish
Library for available finishes. Other wood species are available on an as needed basis. All door styles
are available in 1/2" standard overlay. Other overlays and insets are available as noted on the
availability chart for each door.
Please notice that the minimum size of each door is different. Minimum sizing is critical when 9" base
and wall cabinets are necessary in a design. You will find notes on how each door is handled on a 9"
cabinet, and in some cases it is not available. In general, we try to hold the stile size of the standard
door and vary the left to right overlay.
Inset and beaded inset is available on most mortise & tenon door styles. Please refer to the
Availability Chart for each door. Inset doors use the same edge profile as shown here:
Face
5 degree back bevel
Inset doors and drawer heads are sized to leave a 3/32" gap between the edge of the door and the
face frame, and between butt door pairs. You will be asked to select the Inset Hinge Color. You may
wish to have the hinges match the decorative hardware used in the kitchen. If so, matching
decorative hardware is available from Wellsford Cabinetry.
You will see that some door pictures show a drawer head and others do not. Each door style is
available with a standard drawer head shown in the back of this Selection Guide. Upgraded 5 piece
drawer heads are available for most door styles, and these are also shown. In some cases the
matching drawer heads are not available in 3/8" Inset. An example of this would be the Brighton or
Hastings designs. In any case, 5 piece drawer heads are not recommended in Inset styles due to the
small height of the top drawers and the resulting height of the center panel of the drawer. We suggest
using a combination of matching drawer heads and Slab, Hastings, or Brighton for all 5" high drawers
in Inset applications. Usually, the mitered 5 piece drawer head framing is smaller in width than the
door framing, and the center panel is a flat panel. Mortise & Tenon styles will have stiles that are the
same size as the standard door stile, but the top and bottom rails will be cut down in height.
Mortise & Tenon Design Miter design with equal,
with cutdown rails but reduced framing size

3. www.wellsfordcabinetry.com
ASTORIA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N N
This is a veneer door with a hardwood edge.
MUST SELECT HORIZONTAL OR VERTICAL GRAIN FROM
CUSTOM OPTION.
Contemporary style.
Door faces use Grade A veneer, backs use Grade 1 or 2.
A matching drawer head is always used.
Sequenced or book matched doors not available.
Glass doors will be Quaker style, stiles to be vertical grain, rails to
be horizontal grain.
COLORTONE FINISHES ARE NOT AVAILABLE.
Minimum size 2 1/2" x 7"
LEVEL 1
ALEXANDRIA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1
2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 1
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

4. www.wellsfordcabinetry.com
RICHMOND PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
SPRINGFIELD PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 2
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

5. www.wellsfordcabinetry.com
PROVIDENCE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
COLUMBUS PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 3
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

6. www.wellsfordcabinetry.com
ANNAPOLIS PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
AUGUSTA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 4
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

7. www.wellsfordcabinetry.com
WASHINGTON PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and Standard Overlay. The edge profile does not allow
for 3/8" Inset rabbeting, or concealed hinge boring.
LEVEL 1 2 5/16"
OLYMPIA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 5
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

8. www.wellsfordcabinetry.com
QUAKER PI BI 3/8 I F/O MDH RAD SHP CH ARPV
Mortise & Tenon Door
Plain Inset and Beaded Inset not available
if Miter Design Option is selected.
3/8" Inset door edge changes from 1/8" to 3/16" radius
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1
2 5/16"
CATHEDRAL PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
This is a Design Option for all Level 1 doors except for Astoria,
Stockholm, and Amesbury.
The pictured door is an Alexandria.
Select this door on the Order Front.
Cathedral will apply to wall cabinets and tops of tall cabinets.
Minimum size 8 1/4" x 9 1/4"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Inset will also require the face frame stiles
to be reduced to 1 1/4". Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 1
DESIGN OPTION
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 6
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

9. www.wellsfordcabinetry.com
ARCH PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
This is a Design Option for all Level 1 doors
except for Astoria, Stockholm, and Amesbury.
The pictured door is a Washington.
Select this door on the Order Front.
Arch will apply to wall cabinets and tops of tall cabinets.
Minimum size 8 1/4" x 8 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Inset will also require the face frame stiles
to be reduced to 1 1/4". Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 1
DESIGN OPTION
MITER PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
This is a Design Option for all Level 1 doors except for Astoria,
Stockholm, and Amesbury.
The pictured door is a Richmond.
This option is commonly used to eliminate the end grain on the stiles.
Select this option on the Order Front.
Minimum size 7 1/2" x 7 1/2"
9" base and wall cabinet not available in 3/8" Inset.
Standard Overlay will use full size stiles, but the overlay will be
larger left to right, and a concealed hinge will be used.
LEVEL 1
DESIGN OPTION
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 7
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

10. www.wellsfordcabinetry.com
HL-20 / HR-20 PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
This is a Design Option for all Level 1 doors except for Astoria,
Stockholm, and Amesbury.
The pictured door is a Washington.
Right hand door shown (HR-20)
Add these doors through a modification.
Minimum size 8 1/4" x 9"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Inset will also require the face frame stiles
to be reduced to 1 1/4". Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 1
DESIGN OPTION
STOCKHOLM PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
This is a flat solid wood door.
Battens on back are fixed 3" from top and bottom, and 1 7/8" in
from left and right edges.
Minimum size 6" x 7 1/2"
LEVEL 1 BATTEN ON BACK OF DOOR
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 8
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

11. www.wellsfordcabinetry.com
AMESBURY PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
This Mortise & Tenon door works well as a Shaker
or Contemporary Style.
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Grooved Center Panel available as custom option. Spacing
will match the beaded side and beaded back option (1 1/2").
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 1 2 5/16"
SHAKER PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
This is a traditional wide stile and rail
Mortise & Tenon Shaker Door.
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 8 7/8" x 8 7/8"
9" base & wall cabinets not available in Inset,
3/8" Inset, standard overlay, or full overlay.
LEVEL 2 2 3/4"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 9
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

12. www.wellsfordcabinetry.com
MONROE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N
This Mortise & Tenon door makes a bold
statement with its wide stiles and rails.
Minimum size 9" x 9"
9" base & wall cabinets not available in Inset,
3/8" Inset, standard overlay, or full overlay.
LEVEL 2 2 3/4"
FRANKLIN PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N
This Mortise & Tenon door makes a bold
statement with its wide stiles and rails.
Minimum size 8 7/8" x 8 7/8"
9" base & wall cabinets not available in Inset,
3/8" Inset, standard overlay, or full overlay.
LEVEL 2 2 3/4"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 10
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

13. www.wellsfordcabinetry.com
SAVANNAH PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Minimum size 7 1/2" x 7 1/2"
9" base and wall cabinet not available in 3/8" Inset.
Standard Overlay will use full size stiles, but the overlay will be
larger left to right, and a concealed hinge will be used.
LEVEL 3 2 5/16"
CHARLESTON PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Minimum size 7 1/2" x 7 1/2"
9" base and wall cabinet not available in 3/8" Inset.
Standard Overlay will use full size stile, but the overlay will be
larger left to right, and a concealed hinge will be used.
LEVEL 3 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 11
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

14. www.wellsfordcabinetry.com
BRUSSELS PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Contemporary Style
Minimum size 6 3/4" x 6 3/4"
9" base & wall cabinets in 3/8" Inset will have cut down stiles.
Standard overlay will use full size stiles on 1/2" overlay with
Knife or concealed hinges.
LEVEL 3 2 5/16"
PRESTWICK PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon door with panel grooves 2" on center.
Grooving is centered in panel.
Does not match groove spacing on beaded sides or backs.
Use Amesbury with Panel Grooving Option for a match.
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 3 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 12
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

15. www.wellsfordcabinetry.com
EMMITSBURG PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 3 2 5/16"
SHELDON PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
Mortise & Tenon door
Cabinet must be minimum of 15" wide in standard overlay, 12" wide
in full overlay, to have a 2-panel door. Cabinets not meeting the
width minimum will have a 1-panel door.
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 11 3/8" x 6 3/4"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 4 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 13
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

16. www.wellsfordcabinetry.com
MADISON PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon door
3/8" Inset door edge will change from 1/8" to 3/16" radius.
Minimum size 6 7/8" x 6 7/8"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset.
LEVEL 4 2 5/16"
AUSTIN PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
Mortise & Tenon door
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 4 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 14
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

17. www.wellsfordcabinetry.com
PROVENCAL PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Minimum size 8 5/8" x 8 5/8"
9" base & wall cabinets are not available in 3/8" Inset.
Standard Overlay and Full Overlay will use full size stiles,
but the overlay will be 1 3/8" and a concealed hinge will be used.
LEVEL 4 2 7/8"
PROVENCAL FLAT PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Minimum size 8 5/8" x 8 5/8"
9" base & wall cabinets are not available in 3/8" Inset.
Standard Overlay and Full Overlay will use full size stiles,
but the overlay will be 1 3/8" and a concealed hinge will be used.
LEVEL 4 2 7/8"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 15
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

18. www.wellsfordcabinetry.com
OLD FORGE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Minimum Size 8" x 8"
9" wall & base cabinets in standard overlay will have a 1" overlay
left and right, and a concealed hinge will be used.
LEVEL 4 2 15/16"
PRESTIGE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Minimum size 7 7/8" x 7 7/8"
9" wall & base cabinets in standard overlay will have a 1"
overlay left and right, and a concealed hinge will be used.
LEVEL 4 2 7/8"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 16
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

19. www.wellsfordcabinetry.com
KINGSTON PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
Mortise & Tenon Door
Uses 10141 or Slab Drawer Heads.
Minimum size 8" x 10 1/8"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Inset will also require the face frame stiles
to be reduced to 1 1/4". Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
STILE
SECTION
2 5/16"
LEVEL 4
RAIL
SECTION
3 3/8"
COPENHAGEN PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Contemporary Style
Minimum size 7 1/8" x 7 1/8"
9" base & wall cabinets not available in 3/8" Inset.
Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 5 2 1/2"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 17
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

20. www.wellsfordcabinetry.com
MILAN PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Contemporary Style
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets in Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 5 2 15/16"
MILAN FLAT PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Contemporary Style
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets in Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 5 2 15/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 18
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

21. www.wellsfordcabinetry.com
MIRAGE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N
Mitered Door
Simulates Alexandria Door in Beaded Inset
Works well as Fully Integrated appliance panel
for Beaded Inset Alexandria Door style.
AVAILABLE IN FULL OVERLAY ONLY.
Minimum size 10 5/8" x 10 5/8"
9" wall & base cabinets are not available.
LEVEL 5 3 7/8"
OXFORD PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Hardware space is limited on a matching drawer front.
In an Inset, Standard Overlay, or Full Overlay application
Hastings or Brighton Drawer Heads offer more space while
complimenting the applied molding door style.
Hastings & Brighton Drawer Heads are not available in 3/8 Inset.
Minimum size 7" x 6 3/4"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset.
LEVEL 5 2 5/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 19
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

22. www.wellsfordcabinetry.com
DOVER PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Miter Option Available
Plain Inset and Beaded Inset not available
if mitered option is selected
Minimum Size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles, but
the overlay will be larger and a concealed hinge will be used.
LEVEL 5 2 5/16"
MODENA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N N N
Mitered Door
Minimum Size 7 3/4" x 7 3/4"
9" base & wall cabinets are not available in 3/8" Inset, Beaded
Inset, or Plain Inset.
Standard Overlay and Full Overlay will use 1 1/4" overlay.
LEVEL 5 2 11/16"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 20
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

23. www.wellsfordcabinetry.com
CORNWALL PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N
Mortise & Tenon Door
Decorative Applied Molding in door frame
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 7 1/2" x 7 1/2"
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 5 2 5/16"
CHURCHILL PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Applied Molding on top of door frame
3/8" Inset door edge changes from 1/8" to 3/16" radius.
Minimum size 8 7/8" x 8 7/8"
9" base & wall cabinets are not available in this door style.
LEVEL 6 2 3/4"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 21
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

24. www.wellsfordcabinetry.com
BARCELONA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Miter not available
Minimum Size 9 5/8" x 9 5/8"
9" base and wall cabinets are not available.
LEVEL 6 3 3/8"
BARCELONA FLAT PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N
Mortise & Tenon Door
Miter not available
Minimum Size 9 5/8" x 9 5/8"
9" base and wall cabinets are not available.
LEVEL 6 3 3/8"
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 22
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

25. www.wellsfordcabinetry.com
LASALLE PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mitered Door
Rope Insert in door frame
Minimum Size 8 5/8" x 8 5/8"
9" base & wall cabinets are not available in 3/8" Inset.
Standard Overlay and Full Overlay will use full size stiles,
but the overlay will be 1 3/8" and a concealed hinge will be used.
LEVEL 6 2 7/8"
BAHAMA PI BI 3/8 I F/O MDH RAD SHP CH ARPV
N N N N
Mortise & Tenon Door
2 5/16" Stiles and Top Rail
Bottom Rail varries from 2 1/8" to 2 5/16"
Minimum size 7 1/2" x 7 1/2"
NOT AVAILABLE IN COLORTONE FINISHES
9" base & wall cabinets will have doors with cut down stiles in
Inset and 3/8" Inset. Standard Overlay will use full size stiles,
but the overlay will be larger and a concealed hinge will be used.
LEVEL 9
AVAILABILITY CODES
PI= Plain Inset F/O= Full Overlay SHP= Standard Hood Front Panel Page
BI= Beaded Inset MDH= Matching Drawer Head CH= Concealed Hinge 23
3/8I= 3/8" Inset RAD= Radius ARPV= Standard Arch Raised Panel Valance

26. Standard Drawer Fronts
#10 KEYSTONE # 10141 SLAB
ALEXANDRIA COLUMBUS PROVIDENCE ALL EXCEPT
RICHMOND OLD FORGE ANNAPOLIS ASTORIA
SPRINGFIELD WASHINGTON
AUGUSTA KINGSTON
MONROE AUSTIN
FRANKLIN
SAVANNAH
CHARLESTON
EMMITSBURG
Matching 5-piece Drawer Fronts
ALEXANDRIA AMESBURY FRANKLIN MONROE
SAVANNAH CHARLESTON ALEXANDRIA MITER BRUSSELS

27. PRESTWICK EMMITSBURG SHELDON MADISON
PROVENCAL &
PROVENCAL FLAT OLD FORGE PRESTIGE
MILAN &
COPENHAGEN MILAN FLAT MIRAGE OXFORD
CORNWALL CHURCHILL LASALLE
ROPE
BRIGHTON HASTINGS