Technology for Data Center Monitoring

1. Monitoring & Control
Systems
1
Golden Digital co.

2. Introduction
Env i ronment Monitoring S ys tem Area
◗ Solutions
▹ E n v i ro n m e n t Monitoring S ys t e m in D a t a Centre,
Serv er R o o m , R a c k Monitoring, Freez er R o o m and so on.
◗ Sensors Support
▹ Te m p e ra t u re , Humidity, S m o k e , P o w e r Failure, A c c es s ,
Analog 0-5V,
▹ Water L e a k (Location a n d N o n - Location), A c c e s s Sensor,
▹ E n e r g y Meter, Active P ower, Air Fl ow, Motion a n d m u c h
m o r e …
2

3. Hardwar
eV U T L A N VT335i
Model
Monitoring & Control Systems

4. Overvie
w
VUTLAN VT335i
◗ Specification
▹ Hardware Input:
▹ CAN port for digital sensors
▹ 4 AutoSense RJ-12 ports for sensors
▹ Max. 4 dry contacts
▹ SD Card slot
▹ USB port for web camera or for USB flash for saving logs
▹ Power Output 12V 0.25A x2
Monitoring & Control Systems
4

5. VUTLAN Monitoring System
Model: VT855i
5

6. Diagram
6

7. INPUT
OUTPUT
Processing
Monitoring & Control Systems
Overview
7

8. Hardwar
eVT490 Dual Temperature &
Humidity Sensor
Monitoring & Control Systems

9. Hardwar
eVT560 S m o k e
Sensor
Monitoring & Control Systems

10. Hardwar
eWater L e a k
Sensor
Monitoring & Control Systems

11. Example Layout
Monitoring & Control Systems

12. How to access VUTLAN
?
VUTLAN supports all
Web browser to access
and control.
Monitoring & Control

13. Dashboard
13

14. Dashboard
14

15. Overall
Stats
15

16. System Tree
16

17. System Tree
17

18. VT335i+19”Mounting kit Rack
18

19. VT490 Temp. Humidity
Sensor
19

20. VT560 Smoke
Sensor
20

21. Water Leak Cable Sensor
21

22. ตวอย่างข้อความทาง Email

23. ตวอย่างข้อความทาง SMS

24. ตวอย่างข้อความทาง LINE Application

25. I. VT740 / LTE slot modem
Usage
Can be installed in VT335i , VT825i, VT825ii, new VT825DC, VT825DCDC,
VT825iDC, VT855i, VT855ii, VT855DC, VT855iDC, VT960i v3,
VT960ii v3, monitoring systems.

26. 1. Inventory
Make sure that the contents of the delivery meet the following configuration.
Report a missing or damaged component to your supplier. If damage occurred during
transportation, contact the appropriate delivery service.
Package content Description Quantity
1
LTE modem board
2pcs SMA antenna connectors 1 pc metal plate
2 LTE antennas 2 pcs

27. Panel
1. "Auxiliary" - Connector, used when the modem is installed inside of the appliance to connect LTE
auxiliary antenna. The additional antenna helps to strengthen the signal level. ( Auxiliary LTE antenna is
supplied together with the modem).
2. "Status" - displays modems status. Blinking = working.
3. "SIM card" - SIM card slot with an injector.
4. "Main antenna" - Connector, used when the modem is installed inside of the appliance to connect LTE
main antenna. ( The main antenna is supplied together with the modem).

28. 2. Installation
You can install the modem while the system is turned On. You may wait up to 3
minutes until the Telecom operator information is renewed.
Step 1 1.1 Use the wire cutter tool to cut off
the metal panel labeled “LTE
Modem slot”.
You can dispose of the metal panel
after.
Step 2 Plug the VT740 slot modem as shown on
the picture into the opening. The board
should slide into the guide rails (marked as
“1”) and plug into the jack (marked as
“2”).

29. Step 3 Screw the main LTE antenna
into “Main” antenna” jack.
If you want to strengthen the
signal, you can screw in the
second auxiliary antenna into
“Auxiliary” jack.
Step 4 Plug in the SIM card. The SIM
card slot has an injector.
Step 5 You are ready to go! Turn on the system.
You can install the modem while the system
is turned On. You may wait up to 3
minutes until the Telecom operator
information is renewed.

30. 3. Configuring the modem
Please read the following section for the configuration instructions: Online
documentation page link: The direct page link for users with paper documentation:
https://vutlan.atlassian.net/wiki/spaces/DEN/pages/1016347/Setting+up+a+modem
Modem errors:
Problem Cause Solution
Modem is not initializing. Power light status is not
working.
1. The cable has disconnected due to transportation.
2. The unit is not updated to the latest driver
version.
3. An incorrect converter board is installed inside
the unit by mistake.
1. Power down the device. Open the unit’s case.
Check the cable is connected.
2. Please, update the unit to the latest version.
3. Check if you have a correct converter board
installed inside the unit.

31. II. KMS-30 / Access magnet sensor (ກວດຈ
ັ ບການໄຂປະຕູ ຂອງຫ້ອງເຊ
ີ ເວ
ີ ຫ
ຼື ຕູ້
Outdoor)
1) Function and purpose
For installation inside of IT racks and cabinets, enclosures, doors, and windows. It is used to detect the opening
of doors or windows, garage doors, rack doors, ie . in places , where it is necessary surveillance by means of opening
the magnetic contact. It is but also compatible with many alarms other 3rd party brands. Detection is based on the
separation of two magnetically interconnected parts, of one which is located on the frame door / window and the other
on the door / window. This simple sens or of the basic set alarm requires no power supply, it is powered directly from
the main unit alarm, simply connect it to dry contact inputs of the Vutlan monitoring system.

32. 2. Technical specifications
KMS-30
Recommended operating humidity 5 - 95%
Operating temperature range (TT) -10 - 50 °C
Components Manufactured in E.U.
Max. distance 500. m.

33. 3. Package includes
NO Package content Description
1 Sensor - 1 pc
2 Magnet - x1 pc
4 Screws M3 12.5mm - x4 pcs
7 Sticker - x2 pcs

34. 4. Connection
1. Connect sensor's x2 cables to the 3.5mm power terminal connector as shown
in the picture below. Cables may be swapped.
2. Insert the terminal into the "Dry contact Input" of the Vutlan monitoring system.

35. 5. Installation / mounting
1 1. Mount the "Magnet" (does not
have wires) on the door or window
using the sticker or two screws
supplied in the package.
2. Mount the "Sensing element" (has
two wires) on the door or window
frame.
2 1. Make sure to align the sensors to each
other.
2. Make sure to turn them to each other
as displayed in the picture.
3. The distance between the magnet and
the sensing element should not exceed 8-
10mm.

37. 6. Configuration
Other pages of interest include: "Connecting dry contacts inputs". For internal contacts,
you can specify the type of behavior (normal or reversive) and specify the type of input.
"User-defined type" only affects the icon in the interface. Types can be following: airflow,
door, motion, smoke, vibration, water, and no special type (by default).

38. For dry contacts on the CAN bus, "Alarm" duration control is also available. This holds
on an active level when the signal is already removed from the input. This allows you to
suppress the instability of the input signal, if necessary.

39. The dry contacts window is designed to control dry contacts of internal dry inputs, VT440,
VT16, and other extensions. The general view is shown here:
To create the logic for an arbitrary group of contacts press the button " “in the upper left corner.
This starts with a wizard creating a logic circuit.
As the first step of the wizard, you must select the dry contacts to create a logical scheme.

40. After you click OK, you are prompted to create a trigger.
The trigger can be not created. But in this case, in "THEN" logic circuit can be used only existing elements. As the
last step, you need to edit and create a logic circuit with the OK button.

41. III. VT520DIN
ACVoltmeter
Industrial monitoring & Control
Monitoring your infrastructure 24/7

42. Features
Centralised Monitoring & Control
• Used for measurement of 0-246V, AC
• Very high accuracy
• Can be configured using Vutlan monitoring system to notify and control the equipment in case of
emergency
• Sensor is autodetected in any Vutlan monitoring system
• Analog sensor
• Easy to configure (x4 threshold levels with hysteresis)
Scalability
• Can be used together with any Vutlan monitoring unit: VT325, VT335, VT336, VT805, VT825,
VT900, etc.
• Max. cable length from the unit can be extended using VT408 / Sensor extension

43. Secification
Measured voltage range
Accuracy
Power consumption
Max. distance from the unit
Analog output port
Input terminals
Operating temperature
Operating humidity
Mounting
Dimensions
Protection
Model Name
Manufactured in (country)
Warranty
0-246V, AC
1%
60mW
100m
Autosense bus. RJ-11 (6P4C) cable. Output 0-5V
Strip length 6-7mm, Wire cross 2.5mm ² 22~12AWG
Min. -10... +80°C
5 to 95 %, non-condensing
DIN rail
90.2 x 36.3 x 57.7 mm
IP20H / IP40H
VT520DIN
Slovak Republic, E.U.
90 days

45. IV. VT540 / Vibration sensor (ກວດຈ
ັ ບການສ
ັັ່ ນສະເທ
ຼື ອນ)
1. Function and purpose
Detects vibration. For installation on walls, windows, etc., the sensor controls
vibration. For example, detects the breaking of the window by an intruder if installed
on the window glass.

46. 2. Technical specifications
Feature Description
Sensor type Analog sensor
Dimensions 60×18×18 mm
Weight 60 g
Input RJ-12 / RJ-11 (6p4c)
Outputs RJ11 / RJ12 (6p4c)
Operating
temperature
-10 °C to +80 °C
Operating humidity 5% to 95% (Non-Condensing)
Mounting Mounting bracket, sticker, and screws are included. Installed on the surface where
possible vibration is possible. E.g. windows, doors, etc.
Power consumption 60mW
Max. distance m 150 m
HS Code 9025 11 800
Components Manufactured in E.U.
Daisy chain
possible
No

47. 3. Package includes
NO Package content Description
1 Sensor
2 RJ11 6P4C telephone cable
3 Screw B4,2 x 16 1pc
4 Sticker 1pc

48. 4. Connecting vibration sensor
The sensor uses a standard Vutlan analog RJS5 RJ11 sensor cable for connecting to
the monitoring unit.

49. 5. Installation using a sticker and a bracket
Option 1.
There's a round bump at the bottom of the plastic enclosure of the sensor. It is used for fastening when
the sensor is mounted together with the on walls using a screw. In the current example, it is not needed. If you
are planning to mount a device differently, do not follow this step.

50. Option 2.
a) Stick the mounting sensor to the surface using the sticker. or
b) Stick a sensor to the surface using a screw.

51. Option 3.
Mount the sensor to the surface using a mounting bracket. The mounting
bracket and the sensor can be either attached by the stickers or together
with screws and nuts

52. 6. Analog sensor connection
Connect the analog sensor by a supplied RJ-11 (6P4C) cable to any analog port "A1 .. A8" or
"Sensor" port. The determination of the sensor type and connection will occur automatically

53. 7. 6P4C RJ11 cable wiring/pinouts
1- Yellow, 2- Green, 3- ed, 4 - Black
Daisy chain connection
Colors are true for this telephone cable. Both ends match the colors and pinouts (identical). Please
refer to the RJ connectors comparison table:

54. 8. Extending the number of analog sensors
Using CAN extension "VT408 / Sensor extension unit" it is possible to increase the
number of analog sensors connected to the monitoring unit up to 80 sensor

55. 9. Configuring the sensitivity of the sensor
The sensor is very sensitive. At times this may prove to be too sensitive. In this case, it
is possible to lower the sensor's sensitivity:
1) Unplug the sensor from the cable.
2) Open sensor cover using a flat screw.
3) Take the two-pin jumper header out. This will lower the sensitivity slightly.
4) Close the cover and plug the sensor back in.
If the sensitivity is still too high, Vutlan can produce a custom vibration sensor will a
much lesser sensitivity on demand. In this case, please contact the sales team.

56. 10. Sensor configuration
10.1. Settings tab
To configure a sensor, go to "Main menu" >> "System tree" and click on the sensor
element in the tree. A modal window with sensor properties will pop up. Change the needed
settings and click "OK" or "Apply" at the bottom of the "Properties" window.

57. 10.2. All sensors include:
1 Name The name is given by the system automatically. You can change it to anything you want.
3 ID System ID of the element.
4 Type Example: temperature, humidity, vibration.
5 Class Examples: analog, CAN, switch, discrete.
6 Hardware port The external port number on the device panel to which the sensor is connected (if the sensor is external).
All sensors have threshold controls:

58. ABOUT SERVICE

59. ABOUT SERVICE

60. Access control Set up

61. Access control Set up

62. OUR CUSTOMERS

63. THE COMPANY SUPPORTING IN THE WARRANTY TIME
NO MAINTAINENCE DESCRIPTION QUARANTY CONTACTED
1 Support Team
24/7
Check Hardware of the
Equipment every 3 months
and Report
1 year
Mr. Vilaysack
02095541415
Mr. Phosaka
020 55916959
2 Technical Team
24/7
Check Hardware and
Trubleshoot the problem of
the Equipment every 3
months and Report
Mr. Vilaysack
02095541415
Mr. Loun
020 95335561
3 Technical Team
24/7
Change new if any
Hardware be failed and
Report
Mr. Vilaysack
02095541415
Mr. Loun
020 95335561

64. THE COMPANY MA COST AFTER 1 YEAR WARRANTY
NO MAINTAINENCE DESCRIPTION QUARANTY PRICE/YEAR CONTACTED
1 Support Team 24/7 Check Hardware of the
Equipment every 3 months
and Report
1 year
Mr. Vilaysack
02095541415
Mr. Phosaka
020 55916959
2 Technical Team
24/7
Check Hardware and
Troubleshoot the problem of
the Equipment every 3 months
and Report
Mr. Vilaysack
02095541415
Mr. Loun
020 95335561
3 Technical Team
24/7
Change new if any Hardware
be failed and Report
Mr. Vilaysack
02095541415
Mr. Loun
020 95335561

65. THE COMPANY PACKAGE
NO UNIT/ATM PRICE DISCOUNT FORM
1,947 USD
1 1 To 10 1,947
2 11 To 20 1,928 1%
3 21 To 30 1,908 2%
4 31 To 40 1,898 2.5%
5 41 To 50 1,889 3%
6 51 To 100 1,850 5%