The document provides technical service information about an engine, including:
1. A description of the D7E engine as a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. Details on the identification plate which provides the engine model, serial number, and performance data stamped on the cylinder head cover.
3. A table listing tightening torques for various engine components.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides information on checking camshaft and flywheel signals using VCADS Pro and an oscilloscope. It describes connecting the equipment and performing a test to read off sensor signals. An example readout shows signals from the flywheel and camshaft sensors. Instructions are included for saving the readout files without overwriting originals.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
The document provides information on checking camshaft and flywheel signals from an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform a test to view the sensor signals. An example readout shows signals from the flywheel and camshaft sensors. Instructions are included for saving the readout files.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides information on checking camshaft and flywheel signals using VCADS Pro and an oscilloscope. It describes connecting the equipment and performing a test to read off sensor signals. An example readout shows signals from the flywheel and camshaft sensors. Instructions are included for saving the readout files without overwriting originals.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
The document provides information on checking camshaft and flywheel signals from an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform a test to view the sensor signals. An example readout shows signals from the flywheel and camshaft sensors. Instructions are included for saving the readout files.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdftepu22753653
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust. It has replaceable valve guides.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- Cylinder head gaskets come in three thicknesses to adjust for piston projection.
- Cylinder liners are sealed with two O-rings at the bottom and by the cylinder head gasket at the top.
- Pistons are made of aluminum alloy with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform a test to view the sensor signals. Connecting an oscilloscope to VCADS Pro allows viewing the signals from the flywheel and camshaft sensors to check that they are being received correctly. Saving the read-off is recommended to save the signal data.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdffapanhe306271
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust. It has replaceable valve guides.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- Three different thicknesses of cylinder head gasket are available to accommodate different piston projections.
- The engine uses wet cylinder liners sealed with two O-rings at the bottom and by the cylinder head gasket at the top.
- The pistons are made of aluminum alloy with an eccentric combustion compartment position
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on an engine, including:
1. The D7E engine is a 4-stroke, 6-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an ECU and has electronically controlled EGR to reduce emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and more. Diagrams are provided showing engine components and their locations.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform the test to view the signals from the flywheel and camshaft sensors on the oscilloscope screen. Performing this test allows technicians to check that the sensor signals are being received correctly.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on an engine, including:
1. The D7E engine is a 4-stroke, 6-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an ECU and has electronically controlled internal EGR to reduce emissions.
3. The document contains sections about the cylinder head, cylinder block, cylinder liners, pistons and other engine components.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform the test to view the signals from the flywheel and camshaft sensors on the oscilloscope screen. Performing this test allows technicians to check that the sensor signals are being received correctly.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo L40B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on engine descriptions and service procedures for various components of DEUTZ and VOLVO diesel engines, including:
- The engines are four cylinder, four stroke engines with direct injection and turbocharging.
- Compression tests should yield results between 3-3.8 MPa across cylinders.
- The cylinder head is made of cast iron with vertical inlet and horizontal exhaust on the same side.
- Valves are adjusted using a rotation tool to specified clearances, checking with a feeler gauge.
- The timing gears are located at the flywheel end for the camshaft and power take-off, using stamped markings for setting.
Volvo L35B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information about engines that are equipped on various machine models, including the Deutz-BF4L 1011 FT engine and Volvo D3D and D3.6D engines. It describes the engine components and systems, as well as procedures for removing and installing the engine.
More Related Content
Similar to Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdf
Volvo EC290C L (EC290CL) Excavator Service Repair Manual Instant Download.pdffapanhe306271
This document provides technical specifications and descriptions for engine components of an EC290C L excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdftepu22753653
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust. It has replaceable valve guides.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- Cylinder head gaskets come in three thicknesses to adjust for piston projection.
- Cylinder liners are sealed with two O-rings at the bottom and by the cylinder head gasket at the top.
- Pistons are made of aluminum alloy with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfzu0582kui
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust outlets. It uses three different thickness cylinder head gaskets.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- The cylinder liner is sealed at the bottom by two O-rings and at the top by the cylinder head gasket and clamping force.
- The pistons are made of special alloy aluminum with an eccentric combustion compartment position.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform a test to view the sensor signals. Connecting an oscilloscope to VCADS Pro allows viewing the signals from the flywheel and camshaft sensors to check that they are being received correctly. Saving the read-off is recommended to save the signal data.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides technical specifications and descriptions for engine components of an EC290C LR excavator including:
1. The cylinder head is made of grey cast iron and has vertically entering induction air and horizontally exiting exhaust.
2. The cylinder block is cast in one piece with wet, replaceable cylinder linings.
3. The engine uses cylinder head gaskets of varying thicknesses to meet emissions standards.
Volvo EC290C LR (EC290CLR) Excavator Service Repair Manual Instant Download.pdffapanhe306271
The document provides technical specifications and descriptions for various engine components of the D7E engine, including:
- The cylinder head is made of grey cast iron with vertical air intake and horizontal exhaust. It has replaceable valve guides.
- The cylinder block is cast in one piece with wet, replaceable cylinder liners. Combustion pressure is directed to the main bearings.
- Three different thicknesses of cylinder head gasket are available to accommodate different piston projections.
- The engine uses wet cylinder liners sealed with two O-rings at the bottom and by the cylinder head gasket at the top.
- The pistons are made of aluminum alloy with an eccentric combustion compartment position
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdftepu22753653
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfdai20nao
This document provides information on an engine, including:
1. The D7E engine is a 4-stroke, 6-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an ECU and has electronically controlled EGR to reduce emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and more. Diagrams are provided showing engine components and their locations.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfrou774513po
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform the test to view the signals from the flywheel and camshaft sensors on the oscilloscope screen. Performing this test allows technicians to check that the sensor signals are being received correctly.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on an engine, including:
1. The D7E engine is a 4-stroke, 6-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an ECU and has electronically controlled internal EGR to reduce emissions.
3. The document contains sections about the cylinder head, cylinder block, cylinder liners, pistons and other engine components.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdff8iosedkdm3e
The document provides information about checking camshaft and flywheel signals on an engine using VCADS Pro software and an oscilloscope. It describes how to connect the equipment and perform the test to view the signals from the flywheel and camshaft sensors on the oscilloscope screen. Performing this test allows technicians to check that the sensor signals are being received correctly.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfzu0582kui
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdffijsekkkdmdm3e
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdflunrizan628
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Volvo EC240C NL EC240CNL Excavator Service Repair Manual Instant Download.pdfnie7140zhuang
This document provides information on an engine, including:
1. The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2. The engine uses Common Rail fuel injection controlled by an electronic control unit. Electronically controlled exhaust gas recirculation reduces emissions.
3. The document contains sections about various engine components like the cylinder head, cylinder block, pistons, and their descriptions.
Similar to Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdf (20)
Volvo L40B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on engine descriptions and service procedures for various components of DEUTZ and VOLVO diesel engines, including:
- The engines are four cylinder, four stroke engines with direct injection and turbocharging.
- Compression tests should yield results between 3-3.8 MPa across cylinders.
- The cylinder head is made of cast iron with vertical inlet and horizontal exhaust on the same side.
- Valves are adjusted using a rotation tool to specified clearances, checking with a feeler gauge.
- The timing gears are located at the flywheel end for the camshaft and power take-off, using stamped markings for setting.
Volvo L35B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information about engines that are equipped on various machine models, including the Deutz-BF4L 1011 FT engine and Volvo D3D and D3.6D engines. It describes the engine components and systems, as well as procedures for removing and installing the engine.
Volvo L30B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information for removing and installing an engine. It describes the steps to remove components like the counterweight, hydraulic pump, fuel lines and exhaust pipe. It then outlines the reverse process to install the engine, connecting all components back in place and ensuring proper attachment of hoses, wires and brackets. Special precautions are mentioned like using lifting equipment due to heavy parts and marking disconnected hoses.
Volvo L25F Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
This document provides instructions for removing and installing an engine. It describes disconnecting fuel lines, electrical connections, removing mounting brackets, and lifting the engine out of the machine using hoisting equipment. The installation instructions describe lowering the engine back into place and reconnecting all lines, brackets and electrical connections in the reverse order of removal. Safety warnings are provided to be alert when handling heavy components.
Volvo L25B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on removing and installing a VOLVO diesel engine. It describes:
- Removing components like the air duct, fuel lines, hydraulic pump, and disconnecting electrical connections.
- Lifting the engine out of the machine using a lifting device.
- Installing the engine by lowering it into the engine bay and reconnecting all components in reverse order.
- Reattaching items like the fuel lines, electrical connections, exhaust pipe, and mounting the engine securely.
Volvo L20F Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
This document provides information on removing and installing an engine. It describes the steps to remove the engine by disconnecting electrical and mechanical components like fuel lines, exhaust pipes, and brackets. It then explains the reverse process to install the new engine by reconnecting all components and performing tests to check for proper operation.
Volvo L20B Compact Wheel Loader Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on removing and installing a VOLVO diesel engine. It describes:
- Removing the engine hood, counterweight, fuel lines, electrical connections, and lifting the engine out.
- Installing the engine by lowering it into place, reconnecting fuel lines, electrical connections, and installing the counterweight.
- Tightening engine mount bolts and other fasteners to specified torques is important for a secure installation.
Volvo G990 Motor Grader Service Repair Manual Instant Download.pdfzhenchun51
This document provides instructions for checking camshaft and flywheel signals on an engine using a VCADS Pro computer, oscilloscope, and various connection cables and adapters. The procedure involves connecting the equipment, performing a test operation in the VCADS Pro software, and saving or viewing the signal readouts on the oscilloscope screen to check for proper camshaft and flywheel operation. Connecting various interfaces and changing settings may be required depending on the computer port configuration.
Volvo G976 Motor Grader Service Repair Manual Instant Download.pdfzhenchun51
This document provides instructions for checking camshaft and flywheel signals on an engine using a VCADS Pro computer, oscilloscope, and various connecting cables and adapters. The procedure involves connecting the equipment, performing a test operation in the VCADS Pro software, and saving or viewing the signal readouts on the oscilloscope screen to check for proper camshaft and flywheel operation. Connecting equipment like interfaces, breakout harnesses, and cables is also described.
Volvo G970 Motor Grader Service Repair Manual Instant Download.pdfzhenchun51
This document provides instructions for checking camshaft and flywheel signals on a Volvo engine using a VCADS Pro computer, oscilloscope, and various connecting cables and adapters. The procedure involves connecting the equipment, performing test 28420-3 in the VCADS Pro software, and observing the camshaft and flywheel signals on the oscilloscope screen to check for proper operation. Connecting instructions and notes about interface configurations are also provided.
Volvo G960B Motor Grader Service Repair Manual Instant Download.pdfzhenchun51
The document provides instructions for removing an engine from a machine. It describes disconnecting various engine components like hoses, wiring harnesses, and mounting brackets. Over 40 individual steps are outlined to properly drain fluids, label parts for reinstallation, and detach components like the radiator, fuel lines, charge air cooler, and exhaust system. Special tools are required to lift the engine out of the machine once all connections are removed.
Volvo FC3329C Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information about an engine, including:
1) The D7E engine is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners.
2) The engine uses Common Rail fuel injection controlled by an electronic control unit. Internally recirculated exhaust gas reduces emissions without aftertreatment.
3) The document describes various engine components like the camshaft, crankshaft, vibration damper, and connecting rods. It also provides maintenance instructions for changing the oil level sensor.
Volvo FC2924C Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides technical specifications and descriptions for various engine components of the D7E engine. It includes 3 sentences or less summaries of sections on the cylinder head, cylinder liners, pistons, valves, camshaft, crankshaft, vibration damper, and connecting rod. Diagrams and illustrations are provided to accompany each section. The document appears to be a service manual or technical specification sheet for mechanics working on this engine model.
Volvo FC2421C Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information for an engine, including:
1) The D6E engine is a six-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners. It uses common rail fuel injection controlled by an electronic control unit.
2) The engine model and serial number are stamped on an identification plate attached to the cylinder head cover.
3) Tightening torques are provided for many engine components, such as the cylinder head cover, injectors, fuel lines, and more.
Volvo FC2121C Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides service information for an engine, including:
1) The D6E engine is a six-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners. It uses common rail fuel injection controlled by an electronic control unit.
2) The document describes various engine components like the cylinder head, pistons, valves, and their locations on the engine.
3) Instructions are provided on adjusting the valve clearance and IEGR unit, which requires using special tools and rotating the crankshaft to specific positions.
Volvo EW230C Wheeled Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on the D6E engine configuration, which is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners. It uses Common Rail fuel injection controlled by an electronic control unit. The cylinders are numbered consecutively from the flywheel end and the engine rotates counterclockwise. The engine identification plate provides the model and serial number. The document describes the location of various engine components and systems.
Volvo EW210C Wheeled Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on the D6E engine configuration, which is a four-stroke, straight six cylinder, turbocharged diesel engine with charge air cooling and wet cylinder liners. It uses Common Rail fuel injection controlled by an electronic control unit. The cylinders are numbered consecutively from the flywheel end and the engine rotates counterclockwise. The engine identification plate provides the model and serial number. Key components like the fuel system, cooling system and electrical connections are described. Procedures for removing and replacing the engine are outlined.
Volvo EW180C Wheeled Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides technical specifications and descriptions of engine components for a Volvo D6E diesel engine, including:
- The D6E engine is a 4-stroke, 6-cylinder turbocharged diesel engine with charge air cooling and wet cylinder liners.
- The engine uses a common rail fuel system and electronically controlled internal exhaust gas recirculation.
- The document describes the cylinder head, cylinder liners, pistons, piston rings, and provides diagrams of engine components and their locations.
Volvo EW180 Wheeled Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on an engine characteristic curve, engine description, valve clearance adjustment procedure, fuel injection system overview, and fuel line description for a Cummins B5.9-C engine. It includes engine specifications, diagrams of the engine and its systems, maintenance procedures such as adjusting valve clearance, and descriptions of components like the fuel injection system and fuel lines. Proper maintenance such as adjusting valve clearance every 1000 hours is emphasized for engine efficiency.
Volvo EW145B Wheeled Excavator Service Repair Manual Instant Download.pdfzhenchun51
The document provides information on an engine including:
- The engine is a 6-cylinder turbocharged diesel with a cast iron block and head.
- Gears in the engine case are hardened helical type for strength and reduced noise.
- The block and head have internal passages for lubricating oil and coolant.
- The document includes diagrams showing engine components and their locations.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Manual despiece Yamaha fuera de borda pc_e40x_02.pdf
Volvo EC290C NL EC290CNL Excavator Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Engine, description
D7E - tier 3 compliant
The D7E configuration is a four stroke, straight six cylinder, turbocharged, direct injected diesel engine with charge air
cooling and wet, replaceable cylinder liners.
The D7E engine uses a Common Rail Fuel System controlled by the engine electronic control (E-ECU) software.
Electronically controlled IEGR (Internal Exhaust Gas Recirculation) reduces NO formation and lowers emissions without the
need for exhaust after treatment. Volvo's latest engine management system, EMS 2 is used to control all engine electronic
functions.
The cylinders are numbered consecutively beginning at the flywheel end. Engine rotational direction is counterclockwise as
seen from the flywheel end.
Figure 1
Engine, D7E
2. Service Information
Document Title: Function Group: Information Type: Date:
Engine, identification 200 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Engine, identification
Identification plate
The engine model, serial number and performance data are stamped on an identification plate which is attached on the
cylinder head cover. The engine model designation and serial number must be indicated when ordering spare parts.
Figure 1
Engine identification, D7E
3. Service Information
Document Title: Function Group: Information Type: Date:
Engine, tightening torques 200 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Engine, tightening torques
NOTICE
Regarding bolted joints which are not listed here, see “Volvo standard tightening torques”
Engine, tightening torque
Rocker arm bracket on cylinder head 30 Nm (22.2 lbf ft)
Cylinder head cover (M6) on cylinder head 13 Nm (9.6 lbf ft)
Exhaust return module on cylinder head Step 1: 10 Nm (7.4 lbf ft)
Step 2: 30 Nm (22.2 lbf ft)
Lock nut, valve adjusting screw 20 ±2 Nm (14.8 ±1.5 lbf ft)
Locking screw on cylinder head 34 Nm (25.2 lbf ft)
Solenoid valve on cylinder head 24 Nm (17.8 lbf ft)
Front cover on crankcase Step 1: 3 Nm (2.2 lbf ft)
Step 2: 21 Nm (15.5 lbf ft)
Drain plug on oil pan, M18 55 Nm (40.7 lbf ft)
Crankcase ventilation on cylinder head 21 Nm (15.5 lbf ft)
Return line to return stop valve 30 Nm (22.2 lbf ft)
Return stop valve to crankcase 80 Nm (59.2 lbf ft)
Impulse transmitter (crankshaft) on holder on front cover 9 Nm (6.7 lbf ft)
Impulse transmitter (camshaft) on gearcase 9 Nm (6.7 lbf ft)
Turbocharger on exhaust manifold 42 Nm (31.1 lbf ft)
Clamping shoe injector on cylinder head 16 Nm (11.8 lbf ft)
Injection lines on rail and injector, high pressure line on high-pressure
pump
25 Nm (18.5 lbf ft)
Fuel supply pump on holder 22 Nm (16.3 lbf ft)
Holder fuel supply pump on holder 30 Nm (22.2 lbf ft)
V-belt pulley on fuel supply pump 27 Nm (20.0 lbf ft)
High pressure pump on crankcase, M10 Step 1: 10 Nm (7.4 lbf ft)
Step 2: 50 Nm (37.0 lbf ft)
Fuel control valve 30 Nm (22.2 lbf ft)
Fuel pipe on high pressure pump 29 Nm (21.5 lbf ft)
Fuel pipe on control block 39 Nm (28.9 lbf ft)
Rail on cylinder head 30 Nm (22.2 lbf ft)
Pressure relief valve on rail 100 Nm (74.0 lbf ft)
Rail pressure sensor on rail 70 Nm (51.8 lbf ft)
Pipe clips, fuel line fastening 30 Nm (22.2 lbf ft)
Fuel line on control block, fuel filter console and rail 39 Nm (28.9 lbf ft)
Fuel pipe (return) on control block 49 Nm (36.3 lbf ft)
Fuel pipe (return) on cylinder head 29 Nm (21.5 lbf ft)
Fuel line on fuel filter8 39 Nm (28.9 lbf ft)
Fuel filter console/radiator tank on crankcase 30 Nm (22.2 lbf ft)
5. Service Information
Document Title: Function Group: Information Type: Date:
Component locations 200 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Component locations
Component position, engine D7E. The following figures show the position of a number of components on engine D7E.
Figure 1
Component locations, front side
1 Engine oil filler 11 Engine oil cooler
2 Air inlet 12 Coolant heater port
3 Transport eye 13 Oil dipstick gauge
4 Alternator 14 Power take off
5 Fuel feed pump 15 Fuel filter
6 V-rib belt drive on crankshaft 16 Crankcase bleeding valve
7 V-rib belt 17 High pressure fuel pump
8 Automatic belt tensioner 18 Common rail
9 Engine oil filter 19 Injector
10 Coolant pump 20 Waste gate actuator
6. Figure 2
Component locations, flywheel side
21 Crankcase bleeding valve 28 Air outlet (to charge air cooler)
22 Flywheel housing 29 Coolant inlet
23 Starter motor 30 Coolant outlet
24 Oil pan 31 Air inlet (from charge air cooler)
25 Drain plug 32 Exhaust manifold
26 Oil return line from turbocharger 33 Cylinder rocker arm cover
27 Turbocharger
7. Service Information
Document Title: Function Group: Information Type: Date:
Engine characteristic curve 210 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Engine characteristic curve
Figure 1
Engine, characteristic curve
P Output power
rpm Engine speed
T Torque
be Fuel consumption
8. Service Information
Document Title: Function Group: Information Type: Date:
Basic check, Engine 210 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Basic check, Engine
NOTE!
Certain tests and checks are performed with unlocked safety locking lever. Make sure that the machine cannot operate
unexpectedly when the control lockout lever is unlocked.
Purpose of the basic check
The purpose of the basic check is to provide fast and accurate information about the general condition of the engine.
The basic check should be performed and evaluated according to instructions in the PC-tool VCADS Pro.
Tests included in the basic check
The basic check which is divided into the following tests should be performed after reading out error codes and checking
parameters.
Tests:
1.
2.
3.
Cylinder compression, test
The purpose of the test is to show if any cylinder has a deviating compression pressure. The test replaces the old
pressure check method but does not give any absolute values.
Feed pressure, test
The purpose of the test is to check that the feed pressure is as per specification.
Sensor, test
The purpose of the test is to check the function of all sensors.
9. Service Information
Document Title: Function Group: Information Type: Date:
Troubleshooting 210 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Troubleshooting
General about troubleshooting
When a malfunction is suspected or has been confirmed, it is important to identify the cause as soon as possible.
The starting point for all troubleshooting is that there is some type of trouble symptom or malfunction.
Malfunctions can be indicated by:
generation of error codes
detection of a malfunction symptom.
Troubleshooting work
The first step in troubleshooting is to gather information from the operator concerning the malfunction symptoms, see
Electrical and information system, Collection of basic data. Then, attempt to pin-point the cause by checking in a certain
order, for more information, see Electrical and information system, troubleshooting strategy.
The different checking steps are:
Check error codes
Check parameters
Perform basic check
Troubleshooting information
The following is included in Electrical and information system and is used when troubleshooting:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Troubleshooting strategy
Describes troubleshooting work, step by step.
Troubleshooting, assistive devices
Brief summary of the assistive devices that are available for troubleshooting.
Functional checks and tests, VCADS Pro
Brief description of VCADS Pro. For a detailed description, see VCADS Pro User’s Manual.
Error code information
Contains information regarding error code design, lists of all error codes and error code information about each
error code.
Components, troubleshooting and specifications
Contains methods and measuring values for troubleshooting of components. Also includes wiring diagrams and
certain specifications.
Parameters
Incorrectly set parameters may cause malfunction symptoms. The parameter list includes all limit and command
values for parameters.
Control units, functional description
Describes the functions of the control units, inputs and outputs as well as communication between the various
control units.
Control units, active and passive measuring
Contains measuring values for active and passive measuring of the ECUs.
Software functions
Describes the pre-requisite conditions for the control and monitoring functions that are performed by the software
in the ECUs.
10. Service Information
Document Title: Function Group: Information Type: Date:
Camshaft and flywheel
signals, checking with
VCADS Pro and
oscilloscope
210 Service Information 2014/7/3 0
Profile:
EXC, EC290C L, EC290C LR, EC290C NL [GB]
Camshaft and flywheel signals, checking with VCADS Pro and
oscilloscope
Op nbr 210-090
9990014 Break out harness
9990062 Cable
9998699 Adapter
88890040 Oscilloscope
VCADS Pro VCADS Pro Service Tool
1. Connect 88890040 Oscilloscope to the VCADS Pro computer and perform 28420-3, Flywheel and camshaft signals,
test.
NOTE!
Instructions for how to connect the equipment are described in the VCADS Pro operation.
NOTE!
To be able to start the oscilloscope operation when USB-interface is default in VCADS Pro, then 88890180 Interface
must be connected to the computer. However, in this case the interface does not have to be connected to the
machine.
For computers with only one USB-port, the interface configuration must be changed to 9998555. However, in this
cases the interface does not have to be connected to the machine.
Detailed user support is available under the the menu Help in the software.
NOTE!
The function “Save” overwrites the original file. Therefore, choose “Save as...” to save the read-off.
11. Figure 1
1. Click to start and stop the read-off
Figure 2
Example of read-off of sensor signals with oscilloscope
1.
2.
Signal from flywheel sensor
Signal from camshaft sensor
2. Check that the signal from the camshaft sensor's signal coincides with the signal from the flywheel sensor within
the marked area in the figure.
If the signal for the camshaft sensor is displaced to the left the camshaft is displaced one gear tooth in
the camshaft's rotational direction.
If the signal for the camshaft sensor is displaced to the right the camshaft is displaced one gear tooth
opposite to the camshaft's rotational direction.
For adjusting the camshaft's position, see service manual for respective engine.
12. Figure 3
Relationship between camshaft signal and flywheel signal
A. Area where the signal from the camshaft shall coincide with the signal from the flywheel sensor
1.
2.
Flywheel sensor
Camshaft sensor
Figure 4
Example of incorrect signal
In this case, the signal for the camshaft sensor is displaced to the left.
3. Check that the curves are not mirror-imaged (see figure). If the curves are mirror-imaged:
Check the connection to the oscilloscope.
If the connection to the oscilloscope is correct, check that the connections for the crankshaft sensor are
installed correctly. If needed, unplug the connector for the flywheel sensor and change place of the cable
connections.
13. Figure 5
Example of incorrect signal
In this case, the signal for the flywheel sensor is mirror-imaged
4. Check the voltage across the camshaft sensor.
To ensure reliable start and operation of the engine, the voltage across the sensors shall be according to
.
3021 SE2703, description and measuring
If the signal is too low:
Check that the sensor is correctly installed and adjusted.
Remove the sensor and check that it is not damaged. Check the distance between the sensor and the
sensor ring gear is according to . Install the sensor
386 Engine rotation speed sensor (camshaft), replacing
and check the signal again.
If the sensor is damaged, rotate the crankshaft and check if the camshaft gear has any damage that has
caused damage to the sensor.
Figure 6
A. Signal voltage camshaft sensor (V)
5. Check the voltage across the flywheel sensor.
To ensure reliable start and operation of the engine, the voltage across the sensors shall be according to
14. .
3021 SE2701, description and measuring
If the signal is too low:
Check that the sensor is correctly installed and adjusted.
Remove the sensor and check that it is not damaged. Check the distance between the sensor and the
sensor ring gear/flywheel is according to . Install the sensor
386 Engine rotation speed sensor, replacing
and check the signal again.
If the sensor is damaged, rotate the crankshaft and check if the flywheel has any damage that has caused
damage to the sensor.
Figure 7
A. Signal voltage flywheel sensor (V)
15. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder head, description 211 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Cylinder head, description
The cylinder head is made of grey cast iron and is common for all cylinders. The induction air enters vertically (A) and the
exhausts leave horizontally (B). Inlets and exhaust outlets are located on the same side of the cylinder block. Inlet and
exhaust valve size is increased to optimize the gas exchange and combustion process. Valve guides are replaceable. Coolant
flow in the cylinder head is modified to accommodate an outlet controlled cooling system.
On order for the engine to fulfill governing emission standards, there are 3 cylinder head gaskets of different thicknesses
between the cylinder head and the piston.
Figure 1
16. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder head gasket,
description
211 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Cylinder head gasket, description
The cylinder head gasket is a multi layered gasket with 1, 2 or 3 identification holes to indicate three different thicknesses
available. Selection of the proper thickness of gasket is determined by the measurement of piston projection above the
cylinder block sealing surface. Recalibration for the correct gasket thickness would be required if new pistons or a new
cylinder block were installed.
Figure 1
1. Cylinder head gasket, marking
17. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder block, description 212 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Cylinder block, description
The cylinder block is cast in one piece and has wet, replaceable cylinder linings. Combustion pressure tensile breaking
strength in cylinder head screws is led through stiffened sections of the cylinder block wall directly to the main bearings.
The cylinder block surface should not be ground as the distance between the pistons and the valve heads may become too
small. There is also a risk that injector tips will be incorrectly placed in relation to the pistons and that exhaust values will
worsen.
18. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder liner, description 213 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Cylinder liner, description
The engine has a cylinder block with wet (replaceable) cylinder liners. The bottom part of the liner is sealed against the
cylinder block with two O-rings positioned in grooves machined into the lower end of the liner.
The upper part of the cylinder liner is sealed by the cylinder head gasket and the pressure created by the cylinder head
clamping force against liner protrusion.
Figure 1
Cylinder liner
19. Service Information
Document Title: Function Group: Information Type: Date:
Pistons, description 213 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Pistons, description
D6E Engine
The pistons are made of special alloy aluminium. The piston's combustion compartment has a somewhat off-center
(eccentric) position in relation to the piston pin.
The pistons are provided with 3 piston rings. The first ring has a ring carrier made of cast iron.
The piston is cooled with oil sprayed up on the inside of the piston top.
The piston cooling nozzles are made of plastic and are mounted in the cylinder head by the main bearing positions.
The first piston ring has an asymmetric cross-section area (A). The cross-section area for piston ring number two
(compression ring) is tapered. When installing the piston rings, the marking TOP by the opening in the rings must face up.
The third ring is an oil ring with bevelled edge.
Figure 1
20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
21. Service Information
Document Title: Function Group: Information Type: Date:
Piston rings, description 213 Service Information 2014/7/3 0
Profile:
EXC, EC290C NL [GB]
Piston rings, description
Each piston is equipped with two compression rings and one oil ring. The uppermost compression ring is of the "Keystone"
type (dual trapezoid-formed cross section). Compressions rings should be placed with the text facing upwards.
The oil ring is equipped with two scraping edges, which are pressed against the cylinder wall using the spring tension in the
ring and an expander spring placed on the inside of the ring. The oil ring can be placed on either side but should be placed
with expander spring and oil ring openings 180° from one another.
Figure 1