The document provides instructions for removing an engine and transmission from a vehicle. It describes draining fluids like oil, coolant and transmission fluid. Cross members and underbody skid plates are removed. Then tools are used to lift out the engine and transmission assembly. Wiring harnesses and lines are disconnected as needed.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Bài tập - Tiếng anh 11 Global Success UNIT 1 - Bản HS.doc
Volvo A30E Articulated Dump Truck Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Engine, description
Engine D9B, description
D9B is a straight, six-cylinder, direct-injected diesel engine with 9.4 litre displacement, turbocharger, intercooler and
electronically controlled fuel injection. The valve mechanism receives its movement from the camshaft via rocker arms.
The engine has an overhead camshaft and unit injectors, which are centred above the pistons and controlled by the
camshaft and a control unit (E-ECU). The control unit is located on the engine's left side.
Figure 1
Figure 2
2. Service Information
Document Title: Function Group: Information Type: Date:
Engine, sensor positions 200 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Engine, sensor positions
Control unit sensors
The following is a brief summary of the parts on the engine. There are a number of other parts that affect the system, for
example, the throttle pedal sensor.
The central part of the system, the control unit is positioned on the left side of the engine. All cable connectors for the
engine's sensors are of DIN–standard and are connected in a so-called cable box.
Figure 1
Engine D9, sensors (some have double functions)
1.
2.
3.
4.
Sensor for coolant level, SE2603
Sensor for coolant temperature, cooling circuit converter, SE2601
Sensor for charge air pressure/temperature, SE2507/SE2508
Tachometer sensor, flywheel, SE2701
3. 5.
6.
7.
8.
9.
10.
11.
12.
Sensor for oil level/temperature, SE2205/SE2202
Sensor for crankcase pressure, SE2509
Sensor for oil pressure, SE2203
Camshaft sensor, engine position, SE2703
Sensor for air pressure/temperature, SE2501/SE2502
Sensor for feed pressure, fuel, SE2301
Sensor for water indicator, SE2302
Sensor for coolant temperature, cooling circuit engine/retarder, SE2602
4. Service Information
Document Title: Function Group: Information Type: Date:
Engine, identification 200 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Engine, identification
Identification plate 1
Engine designation, serial number, part number and assembly plant are stamped in one field on the engine block's left front
edge.
Identification plate 2
A decal with the software's ID-number, the engine's serial number and assembly plant is located on the valve cover to
ensure installation of correct ECU on the engine in production. On the back of the ECU, there is a decal indicating its
hardware number. The E-ECU is located on the engine's left side.
Assembly plants:
A = Skövde, Sweden
E = Curitiba, Brazil
F = Flen, Sweden
L = Lyon, France
Figure 1
Identification plate 3
The certification decal is located on the valve cover as well as on the left side, at the back of the machine's front frame inside
of the steps.
6. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
pre-programmed ECU
200 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
E-ECU, MID 128, changing pre-programmed ECU
Op nbr 200-070
This operation also includes required tools and times for applicable parts of the following operations:
200 E-ECU, MID 128, changing non-programmed ECU
1. Connect VCADS Pro computer and perform 17030-3 Parameter, programming.
Use the function: Save all read parameters to job card.
2. Perform step 2–14.
200 E-ECU, MID 128, changing non-programmed ECU
3. Connect VCADS Pro computer and perform 17030-3 Parameter, programming.
Program earlier read-out parameters according to the job card.
7. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
non-programmed ECU
200 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
E-ECU, MID 128, changing non-programmed ECU
Op nbr 200-068
1. Connect VCADS Pro computer and perform 28423-3 MID 128 ECU, programming
When instructed to connect the new control unit, perform steps 2–15.
Removing E–ECU
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3001 Electrical system, special instructions for servicing, electronic components
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
2.
Figure 1
E-ECU
1.
2.
3.
4.
5.
Connector EA
Connector EB
Screw for clamp
Screw for cooler
Screw for ECU
Place the machine in service position.
3. Open the engine hood.
NOTICE
Turn off the electric power with the battery disconnect switch before starting any work. Also remove the
8. fuse for respective component.
4. Remove the three screws (3) that disconnect the clamps from the E-ECU.
5. Unplug the connectors EA and EB from the E-ECU.
6. Remove th screws (4) (6 pcs. ) that hold the cooler (3).
7. Remove the screws (5) (4 pcs.) that hold the E-ECU.
8. Carefully move aside the cooler and remove the E-ECU.
NOTE!
Work carefully so that hoses for the cooler are not damaged.
Mounting E–ECU
9. Lift in the E-ECU inside of the cooler.
10. Install the screws (5) (4 pcs.) that hold the E-ECU against the engine block.
11. Install the screws (4) (6 pcs.) that hold the cooler against the E-ECU.
12. Plug in the connectors EA and EB for the E-ECU.
13. Install the screws (3 pcs.) that hold the clamps against the E-ECU.
14. Close the engine hood.
NOTE!
When changing pre-programmed ECU, return to step 3.
200 E-ECU, MID 128, changing pre-programmed ECU
15. Finish VCADS Pro operation 28423-3 MID 128 ECU, programming.
9. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder compression, PC
test
210 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Cylinder compression, PC test
Connect the VCADS Pro computer and carry out 21006-3 Cylinder compression, test.
(21006-3) This test indicates if there is any deviation in compression in any cylinder in relation to the other cylinders.
10. Service Information
Document Title: Function Group: Information Type: Date:
Compression test 210 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Compression test
Op nbr 210-002
9990006 Puller
9990185 Lifting tool
9996400 Impact puller
9998599 Cleaning tool
9998248 Adapter
9998248 Adapter
9998248 Adapter
9998248 Adapter
9998248 Adapter
9998248 Adapter
9993590 Gear wheel
88880003 Bracket
9988539 Pressure gauge
88820016 Setting tool
This operation also includes the tools and times needed for required parts of the following actions:
191 Service positions
237 Unit injector, adjusting pretension
233 Fuel system, bleeding
214 Valves, adjusting
Removing
1. Place the machine in service position, see .
191 Service positions
2. Lower the front grill and pump up the engine hood.
3. Drain the cylinder head to avoid fuel in the engine oil. Open the connection by the return line on the cylinder head
and install a hose.
Figure 1
11. 4. Loosen the feed hose from the connection by the ECU. Use an air nozzle to get out all of the fuel. Lead the feed
hose into a container Since the feed pump will pump out fuel during the test, the container's volume must be at
least 5 litres (1.3 US gal).
Figure 2
5. Secure the expansion tank with a strap, and then loosen the bracket for the expansion tank.
Figure 3
6. Remove the engine's front lifting eye. This is done to enable installation of the lifting tool on the rocker arm bridge.
7. Remove the hose from the oil trap and remove the valve cover.
8. The condition for reading off correct compression pressure is that the valve clearance is correct. See:
214 Valves, adjusting
9. Remove the IEGR control valve's electrical connections and wipe clean around the control valve. Remove the valve.
12. Figure 4
10. Loosen the bolts for the rocker arm shaft, evenly distributed across the rocker arm shaft to avoid shear stresses.
Remove the bolts.
Lift away the rocker arm shaft with tool 9990185 and 88880003.
Rocker arm shaft's weight: : approx. 30 kg (66 lbs)
Figure 5
9990185
11. Clean very thoroughly around the unit injector. Remove the electrical connection. Remove the bolt for the attaching
yoke. Remove the injector together with the attaching yoke. Use 9996400 Impact puller, 9990262 Adapter, and
9990006 Puller. Remove the other unit injectors in the same way.
NOTE!
Place each injector in separate new plastic bags. Mark which cylinder they were installed in. It is important to not
mix up the injectors since they are classed for a certain cylinder.
13. Figure 6
1.
2.
3.
9996400, Impact hammer
9990262, Adapter
9990006, Puller
12. Clean the copper sleeve with the brush/brushes included in kit 9998599.
Figure 7
1.
2.
3.
Extension
Brush
Protective sleeve
14. 13. Check that all adapters have O-rings and seal against the copper sleeve. Install adapters 9998248 in the unit
injectors' place in the cylinder head.
Figure 8
14. Tighten down the adapter with the unit injector's attaching yoke. Tightening torque: 40 Nm (30 lbf ft).
NOTE!
Keep in mind that the tightening torque here is only for holding the adapter during the test
Figure 9
15. Install the rocker arm bridge with the lifting tool 9990185. Tighten the bolts along the whole rocker arm shaft to
prevent warping and to make sure that the guide pins fit in the camshaft's support bearing. See
.
214 Rocker arm shaft, tightening torques
16. Install the rubber bands so that they are located between the adapter and the unit injector's rocker arm. This is
done so that the rocker arm will not rattle.
15. Figure 10
17. Install the IEGR control valve. Check that the seal ring is placed correctly before the bolts for the IEGR control valve
are tightened.
NOTE!
The parking brake must be applied when cranking the engine with the starter motor.
18. Connect compression gauge 9988539 to adapter 9998248 on the first cylinder. Run the engine with the starter
motor until the needle on the compression gauge stops (max. compression value). Repeat the procedure for the
other cylinders. On a new engine, the compression pressure is normally approx. 30 bar. Low compression pressure
on all cylinders indicates worn cylinder liners and/or worn piston rings. When comparing the compression pressure
in the different cylinders and you detect any cylinder with lower pressure, this may be due to leaking valves,
cracked piston rings, worn cylinder liner, or leaking cylinder head gasket. In case of this, Engine, overhauling should
be done. Uniformity between the cylinders' compression pressure is the most important and should not exceed
20%.
Figure 11
NOTE!
Do not run the starter motor for longer than 10 seconds at a time, with intervals of 60 seconds.
Assembling
19. Loosen the bolts for the rocker arm shaft evenly across the entire shaft, so that the rocker arm shaft is not
subjected to transverse loading. Remove the bolts and install lifting tool 9990185 and 88880003. Carefully lift away
the rocker arm shaft.
20. Remove the compression gauge 9998539 and adapters 9998248.
21. Install the unit injectors in the places where they were installed from the beginning with new O-rings and centre the
unit injectors between the valve springs. Install the attaching yokes. Tightening torque: see
230 Tightening torque, fuel system
16. Figure 12
22. Lift the rocker arm shaft into place with 9990185. Make sure that the guide pins fit in the support bearing for the
camshaft. Tighten the attaching bolts, see .
214 Rocker arm shaft, tightening torques
Figure 13
23. Install the control valve (IEGR-valve).
Figure 14
24. Install the electrical connections for the unit injectors and the control valve.
25. Adjust clearance of the valves and unit injectors, see .
237 Unit injector, adjusting pretension
17. 26. Install the valve cover. Tighten the bolts according to the tightening diagram.
Tightening torques, see 211 Tightening torques, valve cover
27. Install the fuel lines' connections on the cylinder head.
28. Install the bracket for the expansion tank and install the expansion tank.
29. Install the engine's front lifting eye.
30. Bleed the fuel system, see .
233 Fuel system, bleeding
31. Pump down the engine hood and raise the front grill.
18. Service Information
Document Title: Function Group: Information Type: Date:
Engine and transmission,
removing
210 Service Information 2014/8/1 0
Profile:
ART, A30E [GB]
Engine and transmission, removing
Op nbr 210-073
88830051 Lifting tool
This operation also includes required tools and times for applicable parts of the following operations:
191 Service positions
173 Coolant, changing
1. Place the machine in service position, see 191 Service positions
2. Lower the front grill and pump up the engine hood.
Figure 1
Front grill
3. Turn off the electric power with the battery disconnect switch.
4. Remove the front and rear underbody skid plates.
Figure 2
Underbody skid plates
19. 1.
2.
3.
4.
5.
Front underbody skid plate
Rear underbody skid plate, left
Rear underbody skid plate, right
Front cross member
Rear cross member
5. Remove the front and rear cross members.
Weight: approx.15 kg (33 lbs).
6. Drain the hydraulic oil tank.
Volume, see 030 Capacities
The drain nipple is located on the middle of the tank by the suction line for the front hydraulic pumps.
NOTE!
The oil drain hose is inserted in the pipe for the ladder on the inside of the front grill.
Figure 3
Draining hydraulic oil tank
WARNING
Risk of burns. The fluid may be hot.
7. Drain the engine oil.
Volume, see 030 Capacities
Figure 4
Draining engine oil
8. Drain the gearbox oil.
Volume, see Capacities
20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
21. Figure 5
Draining transmission oil
9. Remove the cap for the expansion tank.
Figure 6
10. Drain the coolant, see: 173 Coolant, changing
11. When the expansion tank is empty, open the air bleeder nipples on the cooling pipes.
Figure 7
1. Air bleeder nipples
12. Disconnect the drain hose from the oil sump. Plug and fold it aside.