1. The document provides instructions for performing a compression test on engines D10 and D9. It describes removing injectors and installing an adapter and pressure gauge to test compression pressure on each cylinder.
2. Normal compression pressure is listed as 3.8 MPa (38 bar) (551 psi) at 180 rpm. A difference of up to 10% between cylinders is considered acceptable.
3. Steps are provided for installing the injectors and fuel lines after the test is completed. Safety precautions are noted for working with fuel lines and preventing leaks.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Volvo A30D Articulated Dump Truck Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Engine, description
Engine D10, description
Place of manufacture, serial number
Machine
EU US Brazil
A25D 11001–12999 61001–61118 71001–71999
A30D 10001–11999 60001–60093 70001–72999
The engine is a straight six cylinder, direct-injected diesel with 9.6 litres cylinder capacity, turbo, intercooler and electronically
controlled fuel injection. The valve mechanism receives its movement from the camshaft via valve rods and rocker arms.
The injection pump is equipped with a smoke limiter for torque limitation of the engine. The injectors are mounted in
copper sleeves that are pressed into the cylinder head and directly surrounded by the coolant.
The engine also has an electronic control unit (E-ECU), located on the right radiator bow.
Figure 1
Engine D10B, left side
2. Figure 2
Engine D10B, right side
Engine D9, description
Place of manufacture, serial number
Machine
EU US Brazil
A25D 13001– – 72000–
A30D 12001– – 73000–
Engine D9 is a straight six cylinder, direct-injected diesel with 9.4 litres cylinder capacity, turbo, intercooler and electronically
controlled fuel injection. The valve mechanism receives its movement from the camshaft via valve rods and rocker arms.
The engine has an overhead camshaft and unit injectors, which are centred above the pistons and controlled by the
camshaft and a control unit (E-ECU). The control unit is located on the engine's left side.
4. Service Information
Document Title: Function Group: Information Type: Date:
Engine, sensor positions 200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Engine, sensor positions
Control unit sensors
The following is a brief summary of the parts on the engine. There are a number of other parts that affect the system, for
example, the throttle pedal sensor.
The central part of the system, the control unit is positioned on the left side of the engine. All cable connectors for the
engine's sensors are of DIN–standard and are connected in a so-called cable box.
Figure 1
Engine D9, sensors (some have double functions)
1.
2.
3.
4.
Sensor for coolant level, SE2603
Sensor for coolant temperature, cooling circuit converter, SE2601
Sensor for charge air pressure/temperature, SE2507/SE2508
Tachometer sensor, flywheel, SE2701
5. 5.
6.
7.
8.
9.
10.
11.
12.
Sensor for oil level/temperature, SE2205/SE2202
Sensor for crankcase pressure, SE2509
Sensor for oil pressure, SE2203
Camshaft sensor, engine position, SE2703
Sensor for air pressure/temperature, SE2501/SE2502
Sensor for feed pressure, fuel, SE2301
Sensor for water indicator, SE2302
Sensor for coolant temperature, cooling circuit engine/retarder, SE2602
6. Service Information
Document Title: Function Group: Information Type: Date:
Engine, identification 200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Engine, identification
Identification plate 1
Engine designation, serial number, part number and assembly plant are stamped in one field on the engine block's left front
edge.
Identification plate 2
A decal with the software's ID-number, the engine's serial number and assembly plant is located on the valve cover to
ensure installation of correct ECU on the engine in production. On the back of the ECU, there is a decal indicating its
hardware number. The E-ECU is located on the engine's left side.
Assembly plants:
A = Skövde, Sweden
E = Curitiba, Brazil
F = Flen, Sweden
L = Lyon, France
Figure 1
Identification plate 3
The certification decal is located on the valve cover as well as on the left side, at the back of the machine's front frame inside
of the steps.
7. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
non-programmed ECU
200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Go back to Index Page
E-ECU, MID 128, changing non-programmed ECU
Op nbr 200-068
Applies to machine equipped with engine D10, with serial number according to the table.
Place of manufacture, serial number
Machine
EU US Brazil
A25D 11001–12077 61001–61118 –
A30D 10001–10682 60001–60093 70001–72999
1. Connect VCADS Pro computer and perform 28423-3 MID 128 ECU, programming.
When instructed to connect the new control unit, perform steps 2–15.
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3001 Electrical system, special instructions for servicing, electronic components
Removing E–ECU
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
2. Place the machine in service position.
NOTICE
Turn off the electric power with the battery disconnect switch before starting any work. Also remove the
fuse for respective component.
3. Open the engine hood.
4. Press in the catch and unplug the connector EA/EB from the E–ECU.
8. Figure 1
5. Remove the screws (8 screws) that hold the cooling coil on the E–ECU.
Figure 2
6. Remove two of the four bolts that hold the E–ECU against the console.
Figure 3
7. Hold the E–ECU and remove the two remaining bolts.
9. 8. Lift away the E–ECU.
Figure 4
Mounting E–ECU
9. Grease the upper right connection point with contact grease (to safeguard ground connection).
10. Lift the E–ECU into place.
Figure 5
11. Hold the E–ECU and fit two of the bolts holding the E–ECU against the bracket.
10. Figure 6
12. Fit the two remaining bolts.
13. Fit the screws (8 screws) that hold the cooling coil on the E–ECU.
Figure 7
14. Plug in the connector EA/EB to the E–ECU.
Figure 8
15. Close the engine hood.
NOTE!
When changing pre-programmed ECU, return to step 3.
200 E-ECU, MID 128, changing pre-programmed ECU
16. Finish VCADS Pro operation 28423-3 MID 128 ECU, programming.
11. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
non-programmed ECU
200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Go back to Index Page
E-ECU, MID 128, changing non-programmed ECU
Op nbr 200-068
Applies to machine equipped with engine D9A, with serial number according to the table.
Place of manufacture, serial number
Machine
EU US Brazil
A25D 13001– – –
A30D 12001– – 73000–
1. Connect VCADS Pro computer and perform 28423-3 MID 128 ECU, programming.
When instructed to connect the new control unit, perform steps 2–17.
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3001 Electrical system, special instructions for servicing, electronic components
Removing E–ECU
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
2. Place the machine in service position.
NOTICE
Turn off the electric power with the battery disconnect switch before starting any work. Also remove the
fuse for respective component.
3. Open the engine hood.
4. Unplug the EM connector from the engine.
12. Figure 1
1.
2.
EM connector
Clamp
5. Remove the clamp that holds the cable harness to the E–ECU.
6. Remove the screws (8 pcs.) that hold the cooling circuit and the console for the clamp.
Figure 2
1.
2.
Cooling circuit
Console
7. Press in the catch and unplug the connector EA/EB from the E–ECU.
Figure 3
13. 8. Remove the four screws that hold the E–ECU against the engine block
9. Uncover and lift away the E-ECU upward
Figure 4
Mounting E–ECU
10. Grease the upper right connection point with contact grease (to safeguard ground connection).
Figure 5
11. Lift the E–ECU into place.
Figure 6
12. Fit the screws that hold the E–ECU against the engine block
13. Fit the screws (8 pcs.) that hold the cooling circuit and the console.
14. Figure 7
14. Plug in the connector EA/EB to the E–ECU.
15. Secure the cable harness for the ECU by fitting the clamp in the console.
16. Plug in the connector EM for the engine.
17. Close the engine hood.
NOTE!
When changing pre-programmed ECU, return to step 3.
200 E-ECU, MID 128, changing pre-programmed ECU
18. Finish VCADS Pro operation 28423-3 MID 128 ECU, programming.
15. Service Information
Document Title: Function Group: Information Type: Date:
E-ECU, MID 128, changing
non-programmed ECU
200 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Go back to Index Page
E-ECU, MID 128, changing non-programmed ECU
Op nbr 200-068
1. Connect VCADS Pro computer and perform 28423-3 MID 128 ECU, programming
When instructed to connect the new control unit, perform steps 2–15.
Removing E–ECU
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
3001 Electrical system, special instructions for servicing, electronic components
CAUTION
Always follow instructions according to Electrical system, work instructions, electronic components
2.
Figure 1
E-ECU
1.
2.
3.
4.
5.
Connector EA
Connector EB
Screw for clamp
Screw for cooler
Screw for ECU
Place the machine in service position.
3. Open the engine hood.
16. NOTICE
Turn off the electric power with the battery disconnect switch before starting any work. Also remove the
fuse for respective component.
4. Remove the three screws (3) that disconnect the clamps from the E-ECU.
5. Unplug the connectors EA and EB from the E-ECU.
6. Remove th screws (4) (6 pcs. ) that hold the cooler (3).
7. Remove the screws (5) (4 pcs.) that hold the E-ECU.
8. Carefully move aside the cooler and remove the E-ECU.
NOTE!
Work carefully so that hoses for the cooler are not damaged.
Mounting E–ECU
9. Lift in the E-ECU inside of the cooler.
10. Install the screws (5) (4 pcs.) that hold the E-ECU against the engine block.
11. Install the screws (4) (6 pcs.) that hold the cooler against the E-ECU.
12. Plug in the connectors EA and EB for the E-ECU.
13. Install the screws (3 pcs.) that hold the clamps against the E-ECU.
14. Close the engine hood.
NOTE!
When changing pre-programmed ECU, return to step 3.
200 E-ECU, MID 128, changing pre-programmed ECU
15. Finish VCADS Pro operation 28423-3 MID 128 ECU, programming.
17. Service Information
Document Title: Function Group: Information Type: Date:
Compression test 210 Service Information 2014/8/15
Profile:
ART, A30D [GB]
Compression test
Op nbr 210-002
9998009 Adapter
9998532 Extractor
9988539 Pressure gauge
Condition: Valves correctly adjusted, see .
214 Valves, adjusting
1. Place the machine in service position.
2. Clean thoroughly around the injectors, also around the connections for the fuel pressure lines and leak-off fuel
lines.
WARNING
The fuel pressure lines are pre-shaped and may not be altered for any reason.
If a pre-shaped fuel line is bent or deformed, there is a great risk that it will rupture.
A damaged fuel pressure line must always be changed!
Removing
3. Remove the fuel pressure lines. The pipes are clamped in two groups of three, and the clamping should not be
loosened.
NOTICE
Fit protective caps on all injectors and on the injection pump's connections.
Figure 1
4. Unplug the connector for sensor SE2308 and remove the bracket.
5. Remove the leak-off fuel line between the injectors.
18. NOTE!
If compression check is to be performed on cylinder 6, loosen and fold aside the pipe between the turbocharger
and intercooler.
6. Remove the nuts for the injector yokes and remove the yokes.
Figure 2
7. Remove the rubber seals around the injectors.
8. Remove the injector on cylinder no. 1 by twisting the injector and pulling up at the same time. If needed, use
9998532 Extractor to remove the injector.
Figure 3
9. Install 9998009 Adapter and tighten it down with the injector's attaching yoke and nut.
Tightening torque: 50 Nm(37 lbf ft).
NOTE!
Check that the compression gauge's seal ring is intact.
19. Figure 4
1.
2.
9998009 Adapter
9988539 Pressure gauge
10. Connect 9988539 Pressure gauge.
11. Press in the Safety stop. The safety stop is located on the right side of the operator's panel. This is to prevent fuel
from flowing out from the pressure valves on the injection pump when the engine is turned with the starter motor.
12. Check that the gearshift selector is in neutral.
13. Turn over the engine with the starter motor for 5 seconds and read off the value.
14. Remove the checking equipment and refit the injector with new copper washer and rubber seal.
Tightening torque: 50 Nm(37 lbf ft).
15. Perform compression check on cylinders 2, 3, 4, 5 and 6 in the same way as for cylinder 1.
Normal compression pressure is 3.8 MPa (38 bar)(551 psi) at 180 rpm.
NOTICE
A difference of up to 10% in compression between cylinders is acceptable and does not indicate a need for
further action, i.e. reconditioning of the valves.
Installing
16. Fit the yokes and the nuts.
Tightening torque: 50 Nm(37 lbf ft).
Figure 5
17. Fit the leak-off fuel line, use new copper washers.
NOTE!
20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
21. If compression check has been performed on cylinder 6, fit the pipe between the turbo and the intercooler.
WARNING
The fuel pressure lines are pre-shaped and may not be altered for any reason.
If a pre-shaped fuel line is bent or deformed, there is a great risk that it will rupture.
A damaged fuel pressure line must always be changed!
18. Fit the fuel pressure lines. Make sure that the area is clean and that the fuel pressure lines are not bent or altered in
any way. Tighten the pressure line nuts.
Tightening torque: 15–25 Nm(11–18 lbf ft).
Figure 6
19. Fit the bracket and sensor SE2308.
20. Restore the stop function. Start the engine and check to make sure that there are no leaks.
21. Run the engine with increased engine speed for approx. 5 minutes to remove any remaining air.