The document describes 3M Scotchcast resin joint kits 92-NA-x-U, which are designed for joining low voltage energy cables in hazardous areas. The kits provide electrical insulation and mechanical protection of cable joints using a flame retardant and chemical resistant resin. The kits contain a transparent mould body, resin bags with a closed mix system, spacers, tapes, gloves, and instructions. The resin provides insulation for indoor and outdoor applications, including underground and submerged joints.
3M LVI-1/2 Scotchcast Resin Cable Joints
Resin Joints - 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 6sqmm - LV1-1/2 Kit
Up to 25mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M Pilot and Telecom cable joints suit multicore (2-37 core) and multipair (2-100 pair) polyethylene (PE) or PVC insulated cables, steel wire armoured and unarmoured - Scotchlok UR2 connectors provide quick and reliable jointing of multi-pair stranded copper conductors, compression crimp connectors are recommended for multi-core cable joints.
3M Pilot and Telecom cable jointing kits are suitable for cable jointing polymeric pilot and telecom cables in indoor, outdoor, submerged and underground direct burial applications.
3M Scotchcast Resin Cable Jointing Kits - Pilot & Telecom Cables, Contents
*Translucent cable jointing shell
*3M Scotchcast 470W resin
*3M Scotch 23 self amalgamating tape
*Constant force springs
*Spacer web tape
*Cable jointers instruction
3M LVI-1/2 Scotchcast Resin Cable Joints
Resin Joints - 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 6sqmm - LV1-1/2 Kit
Up to 25mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M Pilot and Telecom cable joints suit multicore (2-37 core) and multipair (2-100 pair) polyethylene (PE) or PVC insulated cables, steel wire armoured and unarmoured - Scotchlok UR2 connectors provide quick and reliable jointing of multi-pair stranded copper conductors, compression crimp connectors are recommended for multi-core cable joints.
3M Pilot and Telecom cable jointing kits are suitable for cable jointing polymeric pilot and telecom cables in indoor, outdoor, submerged and underground direct burial applications.
3M Scotchcast Resin Cable Jointing Kits - Pilot & Telecom Cables, Contents
*Translucent cable jointing shell
*3M Scotchcast 470W resin
*3M Scotch 23 self amalgamating tape
*Constant force springs
*Spacer web tape
*Cable jointers instruction
3M Scotchcast Inline Cable Joints 91-NBA with 470W Resin
3M Scotchcast resin cable joint kits 91-NBA are designed to be used for cable jointing low voltage LV unarmoured single core and multi-core (2, 3, 4 and 5 core) cables. 3M Scotchcast resin cable joints incorporate electrical insulation and mechanical protection of unarmoured cable joints with compression or mechanical connectors. 3M Scotchcast unarmoured cable joints can be used for indoor and outdoor, underground and submerged applications.
Unarmoured Cable Joints - 3M Scotchcast Inline Cable Joints 91-NBA with 470W Resin - Features
• 3M Scotchcast resin 470W in transparent two chamber bags with integrated 3M Closed Mixing and Pouring (CMP) cable jointing system
• One part translucent cable joint mould body with snap fit closing system for quick and easy handling by the LV cable jointers
• Pre cut foam sealing elements to provide reliable sealing to the cable joint mould body without tooling for all cable application diameters
• Closure cap to prevent any pollution
3M LVI-1/5 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 50sqmm - LV1-1/5 Kit
Up to 45mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
3M LVI-1/7 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 150sqmm - LV1-1/7 Kit
Up to 64mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description3M LVI-1/7 Cable Joints (Scotchcast Resin)
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
3M LVI-1/5 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 50sqmm - LV1-1/5 Kit
Up to 45mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
3M Scotchcast Inline Cable Joints 91-NBA with 470W Resin
3M Scotchcast resin cable joint kits 91-NBA are designed to be used for cable jointing low voltage LV unarmoured single core and multi-core (2, 3, 4 and 5 core) cables. 3M Scotchcast resin cable joints incorporate electrical insulation and mechanical protection of unarmoured cable joints with compression or mechanical connectors. 3M Scotchcast unarmoured cable joints can be used for indoor and outdoor, underground and submerged applications.
Unarmoured Cable Joints - 3M Scotchcast Inline Cable Joints 91-NBA with 470W Resin - Features
• 3M Scotchcast resin 470W in transparent two chamber bags with integrated 3M Closed Mixing and Pouring (CMP) cable jointing system
• One part translucent cable joint mould body with snap fit closing system for quick and easy handling by the LV cable jointers
• Pre cut foam sealing elements to provide reliable sealing to the cable joint mould body without tooling for all cable application diameters
• Closure cap to prevent any pollution
3M LVI-1/5 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 50sqmm - LV1-1/5 Kit
Up to 45mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
3M LVI-1/7 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 150sqmm - LV1-1/7 Kit
Up to 64mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description3M LVI-1/7 Cable Joints (Scotchcast Resin)
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
3M LVI-1/5 Scotchcast Resin Cable Joints
Resin Joints- 3M Scotchcast Cable Joints Kits LV
2, 3, 4 Core Resin Cable Jointing Kits - 3M
Resin Joints - Low Voltage Underground Resin Cable Joint Kits
3M Scotchcast Resin Joint - 4 Core up to 50sqmm - LV1-1/5 Kit
Up to 45mm OD cables accomodated in cable joint shell
3M Scotchcast resin (470W) cable joints are designed to joint multi-core armoured (SWA or GSWB), polymeric (XLPE EPR) low voltage power cables - 3M cable joints provide electrical insulation and mechanical protection with either compression or mechanical connectors - 3M LVI-1 power cable joints have now replaced the 3M LA range of joints.
3M LVI-1 Resin Joints - Kit Description
3M Scotchcast LVI-1 resin inline cable joints are delivered with a one part translucent mould body for simple and easy handling by cable jointers. Distances inside the joint body can be checked easily. All necessary dimensions, such as cable application range, are covered in the cable jointing instruction. The two foam sealing elements can be adapted to the required cable diameter by removing the pre-cut adapter rings. Scotchcast resin 470W is supplied in two chamber bag with integrated spout and aluminium guard bag for protection against humidity. The re-openable seam and integrated spout with membrane provides a unique Closed Mixing and Pouring Cable Joint System. After the seam of the two chamber resin bag is opened, the resin components can be mixed. To pour the cable jointing resin into the mould body, the spout is connected with the dome by turning 180 degrees. While turning, the membrane is cut open to pour the Scotchcast 470W resin into the cable joint - the Closed Mixing and Pouring Systems provides resin handling without any skin contact by cable jointers.
3M LVI-1 Resin Cable Joint Kits - Maximum Cable ODs (mm)
LVI-1/2 Resin Cable Joint Kit - 25mm
LVI-1/3 Resin Cable Joint Kit - 32mm
LVI-1/4 Resin Cable Joint Kit - 36mm
LVI-1/5 Resin Cable Joint Kit - 45mm
LVI-1/6 Resin Cable Joint Kit - 54mm
LVI-1/7 Resin Cable Joint Kit - 64mm
LVI-1/8 Resin Cable Joint Kit - 77mm
Similar to Unarmoured Cable Joints for Hazardous Areas (Zone 1 & 2) (20)
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
Software Delivery At the Speed of AI: Inflectra Invests In AI-Powered QualityInflectra
In this insightful webinar, Inflectra explores how artificial intelligence (AI) is transforming software development and testing. Discover how AI-powered tools are revolutionizing every stage of the software development lifecycle (SDLC), from design and prototyping to testing, deployment, and monitoring.
Learn about:
• The Future of Testing: How AI is shifting testing towards verification, analysis, and higher-level skills, while reducing repetitive tasks.
• Test Automation: How AI-powered test case generation, optimization, and self-healing tests are making testing more efficient and effective.
• Visual Testing: Explore the emerging capabilities of AI in visual testing and how it's set to revolutionize UI verification.
• Inflectra's AI Solutions: See demonstrations of Inflectra's cutting-edge AI tools like the ChatGPT plugin and Azure Open AI platform, designed to streamline your testing process.
Whether you're a developer, tester, or QA professional, this webinar will give you valuable insights into how AI is shaping the future of software delivery.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Slack (or Teams) Automation for Bonterra Impact Management (fka Social Soluti...Jeffrey Haguewood
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on the notifications, alerts, and approval requests using Slack for Bonterra Impact Management. The solutions covered in this webinar can also be deployed for Microsoft Teams.
Interested in deploying notification automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
Slack (or Teams) Automation for Bonterra Impact Management (fka Social Soluti...
Unarmoured Cable Joints for Hazardous Areas (Zone 1 & 2)
1. 3 ScotchcastTM
RoHS
2002/95/EC
REACH
1907/2007/EC
Resin Kits 92-NA-x-U Series
Inline Joint Kit with Resin 1402FR for Hazardous Areas
Flame Retardant, Hydrocarbon Resistant, Halogen Free
Application
3M™ Scotchcast™ resin joint kits 92-NA-x-U are designed to be used for multi-core non
shielded, polymeric, low voltage energy cables in hazardous areas. The application
incorporates electrical insulation and mechanical protection of joints with compression or
mechanical connectors which is flame retardant and chemical resistant. They can be used
for indoor and outdoor, underground and submerged applications.
Features
• Resin 1402FR in transparent two chamber bags with integrated Closed Mix system
and an opener for easy opening and pouring.
• Two part Mould Body with Snap Fit closing system for quick and easy handling.
• Transparent flame retardant Mould Body for easy control of connector distances.
• Flame retardant according to UL94 V0.
• Chemical resistant, especially against hydro carbons.
• Spacer web to ensure the distance between connectors and the Mould Body.
• Closure cap to prevent any pollution.
Kit content
• Transparent PC Mould Body with closure cap
• ScotchcastTM
1402FR resin bag with Closed Mix system and separate opener
• Phase Spacer web
• Scotch 23 electrical insulation tape
• Abrasive strip
• Finger gloves according to EN 394
• Detailed instruction
Page 1 of 3
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
2. Product Description
3MTM
ScotchcastTM
92-NA-x-U Series Kits will be delivered with a two part transparent mould
body for simple and easy handling. Distances inside the body can be checked easily.
All necessary dimensions are given in the detailed instruction.
The two half Mould Bodies can be adapted to the required cable diameter by cutting the
marked areas at the ends.
A flame retardant spacer web ensures the minimum required distance to each connector and
the Mould Body.
The resin 1402FR is delivered in two chamber bag with integrated spout and aluminium
Guard Bag for protection against humidity.
The reopenable seam and integrated spout with a membrane provides a Closed mixing
system. A separate opener ensures a quick and tool free opening of the bag, and easy
pouring of the resin.
To provide resin handling without any skin contact, disposable gloves meeting EN394 are
provided with the kit.
For protection against pollution, a closure cap is applied onto the dome.
After curing, the remaining resin in the bag can be disposed as household waste.
Product Selection
Application Range
Kit Reference 92-NA-1-U 92-NA-2-U 92-NA-3-U 92-NA-4-U 92-NA-5-U 92-NA-6-U
CSA (mm²) 1.5 – 10 16 – 25 25 – 50 50 – 95 95 – 150 150 – 240
Cable Ø(mm) 8 – 22 14 – 30 23 – 35 28 – 47 33 – 55 45 – 70
Testing
The full ScotchcastTM
Resin Kit Series 92-NA-0-U up to 92-NA-6-U were tested according
EN50393 Table 3 / I / A1
Type of Test according to EN50393 Table 3 / I / A1 Results
AC Voltage Withstand Test in air 4kV AC/ 1 min passed
Insulation Resistance Test in air 1kV DC > 10.000MΩ
Heat Cycle in air 63 cycles: 5h/3h passed
Heat Cycle in water 63 cycles: 5h/3h passed
AC Voltage Withstand Test in water 4kV AC/ 1 min passed
Insulation Resistance Test in water 1kV DC > 10.000MΩ
Usage Information
The resin will be supplied, in two-chamber plastic pouches with peelable barrier in the correct
stoichiometric proportion. This type of packaging will assure the correct mixing ratio for
applying the resin.
The packaging includes a Closed Mix Delivery System. The integrated pouring spout is
opened by using the supplied opener.
For other information, relevant for the usage of the resin, like Gel-Time, Pot-Life, viscosity,
density etc. please see the Data Sheet for the 1402FR Resin.
Page 2 of 3