Things To Know #5 Powerpoint

1. T.T.K.#5T.T.K.#5
ENGINE BLOCKENGINE BLOCK
CONSTRUCTIONCONSTRUCTION
AND SERVICEAND SERVICE

2. T.T.K.#5T.T.K.#5
PRECAUTIONS FOR ENGINE REMOVAL

3. T.T.K.#5T.T.K.#5
WATCH THOSE PIECES HANGIN OFF THE
MOTOR!

4. T.T.K.#5T.T.K.#5
IT MAY BE A LONG TIME BEFORE YOU
NEED TO PLUG THIS STUFF BACK IN!

5. T.T.K.#5T.T.K.#5
SOMETIMES DESCRIPTION IS BETTER

6. IT IS IMPORTANT TO USE PROPER TOOLS!
T.T.K.#5T.T.K.#5

7. T.T.K.#5T.T.K.#5
IT TAKES LESS TIME TO DO IT RIGHT!

8. GOOD IDEA TO HAVE A COUPLE OF THESE
T.T.K.#5T.T.K.#5

9. T.T.K.#5T.T.K.#5
MORE THAN ONE WAY TO BLOCK OFF A
LINE
T.T.K.#5

10. T.T.K.#5T.T.K.#5
GUIDE PINS, SORRY BAD PICTURE

11. STATIC TIMING
T.T.K.#5T.T.K.#5

12. T.T.K.#5T.T.K.#5
RING RIDGE

13. T.T.K.#5T.T.K.#5
GREATEST AREA OF WEAR

14. T.T.K.#5T.T.K.#5
THERE ARE MANY TYPES OF RIDGE
REAMERS

15. T.T.K.#5T.T.K.#5
THIS IS THE RING RIDGE AREA

16. CORRECT AND INCORRECT REAMER CUTS
T.T.K.#5T.T.K.#5

17. T.T.K.#5T.T.K.#5
CHECK AND MARK MAIN CAPS

18. MARKING THE RODS AND CHECKING THE
PISTON
T.T.K.#5T.T.K.#5

19. T.T.K.#5T.T.K.#5
ALWAYS PROTECT THE CRANKSHAFT

20. SHORT BLOCK ASSEMBLY
T.T.K.#5T.T.K.#5

21. THE LONG BLOCK
T.T.K.#5T.T.K.#5

22. THE LONG BLOCK
T.T.K.#5T.T.K.#5

23. THE LONG BLOCK, SMOG CONCIDERATIONS
T.T.K.#5T.T.K.#5

24. T.T.K.#5T.T.K.#5
THREAD FIT WHEN HOT

25. T.T.K.#5T.T.K.#5
FRONT VIBRATION DAMPER PULLER

26. T.T.K.#5T.T.K.#5
PROPER WAY TO REMOVE THE VIBRATION
DAMPER

27. T.T.K.#5T.T.K.#5
WHY?

28. CAPS, WEBS, AND ALIGNMENT
T.T.K.#5T.T.K.#5

29. T.T.K.#5T.T.K.#5
NOT STRAIGHT, BORE IT!

30. POUNDED CAPS!
T.T.K.#5T.T.K.#5

31. T.T.K.#5T.T.K.#5
CHECKING FOR OUT OF ROUNDNESS OF THE
MAIN BORE

32. CHECKING THE DECK
T.T.K.#5T.T.K.#5

33. CHECK WITH REFERENCE ON WERE TO
CHECK
T.T.K.#5T.T.K.#5

34. T.T.K.#5T.T.K.#5
DECK SURFACING

35. ANOTHER DECK MACHINE $$$$$$$$$$$$$$!
T.T.K.#5T.T.K.#5

36. CHECK FOR PHYSICAL DAMAGE
T.T.K.#5T.T.K.#5

37. BORE GAUGE
T.T.K.#5T.T.K.#5

38. T.T.K.#5T.T.K.#5
TELESCOPING OR SNAP GAUGE

39. T.T.K.#5T.T.K.#5
CHECKING FOR TAPER AND OUT OF
ROUNDNESS

40. WHAT AND WHY IS CYLINDER TAPER
T.T.K.#5T.T.K.#5

41. T.T.K.#5T.T.K.#5
OLDER BORING TOOL

42. NEWER BORING TOOL
T.T.K.#5T.T.K.#5

43. T.T.K.#5T.T.K.#5
HONING STRESS PLATE

44. T.T.K.#5T.T.K.#5
TESTING CYLINDER WALL THICKNESS

45. T.T.K.#5T.T.K.#5
START WITH A STRAIT BORE

46. T.T.K.#5T.T.K.#5
DEGLAZING HONES

47. CROSSHATCH PATTERN
T.T.K.#5T.T.K.#5

48. T.T.K.#5T.T.K.#5
CYLINDER WALL

49. T.T.K.#5T.T.K.#5
PLATEAU HONING

50. T.T.K.#5T.T.K.#5
DRY SLEEVE

51. T.T.K.#5T.T.K.#5
WET SLEEVE

52. T.T.K.#5T.T.K.#5
PLENTY OF GOOD OL SOAP!

53. DRY SLEEVE INSTALLATION
T.T.K.#5T.T.K.#5

54. T.T.K.#5T.T.K.#5

55. CAM BEARING HOLE ALIGNMENT
T.T.K.#5T.T.K.#5

56. T.T.K.#5T.T.K.#5

57. T.T.K.#5T.T.K.#5

58. T.T.K.#5T.T.K.#5

59. T.T.K.#5T.T.K.#5

60. T.T.K.#5T.T.K.#5

61. T.T.K.#5T.T.K.#5

62. T.T.K.#5T.T.K.#5