Stihl MS 171 Chainsaw Service Repair Manualufjjdfjjskekmd
This is the Highly Detailed factory service repair manual for theSTIHL MS 171 CHAINSAW, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.STIHL MS 171 CHAINSAW Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
Safety precautions
Specifications
Troubleshooting
Cutting attachment
Clutch
Chain brake
Engine
Ignition system
Rewind starter
Servicing the AV system
Master control lever
Chain lubrication
Fuel system
Special servicing tools
Servicing aids
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveSTIHL MS 171 CHAINSAW Service Repair Workshop Manual.
Thanks for visiting!
Stihl MS 171 Chainsaw Service Repair Manualufjjdfjjskekmd
This is the Highly Detailed factory service repair manual for theSTIHL MS 171 CHAINSAW, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.STIHL MS 171 CHAINSAW Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Introduction
Safety precautions
Specifications
Troubleshooting
Cutting attachment
Clutch
Chain brake
Engine
Ignition system
Rewind starter
Servicing the AV system
Master control lever
Chain lubrication
Fuel system
Special servicing tools
Servicing aids
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveSTIHL MS 171 CHAINSAW Service Repair Workshop Manual.
Thanks for visiting!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
3. 2 TS 700, TS 800
This service manual contains
detailed descriptions of all the
typical repair and servicing
procedures for this cut-off machine
series.
Service procedures on
standardized parts and assemblies
which are used in several STIHL
power tool series are summarized in
separate service manuals.
Reference is made to these at the
appropriate points in this manual.
Refer to the illustrated spare parts
lists during all repair work. These
lists show the installation position
and order in which the individual
parts and modules should be
assembled.
Refer to the latest edition of the
relevant parts list to check the part
numbers of any replacement parts
required.
A fault on the machine may be due
to several causes. To help locate
the fault, consult the chapter on
"Troubleshooting" and the "STIHL
Service Training System" for all
function groups.
Refer to the "Technical Information"
bulletins for engineering changes
which have been introduced since
publication of this service manual.
Technical information bulletins also
supplement the parts list and
service manual until an updated
edition is issued.
The special tools mentioned in the
descriptions are listed in the chapter
"Special tools" of this manual. Use
the part numbers to identify the
tools in the STIHL Special Tools
manual.
It lists all the special servicing tools
currently available from STIHL.
To help you use this manual and
understand it more clearly, the text
and illustrations are marked by
graphic symbols as follows:
In the text:
: = Action to be taken
as shown in the illustration
above the text
– = Action to be taken
but not shown in the illustration
above the text
In the illustrations:
A Item pointer (short)
aDirection of movement
(long arrow)
b 4.2 = Reference to another
chapter, i.e. to chapter 4.2
in this case.
Service manuals and technical
information bulletins are intended
exclusively for the use of properly
equipped repair shops. They must
not be passed on to third parties.
Servicing and repairs are made
considerably easier if the clamp (3)
5910 890 2000 is used to mount the
machine on assembly stand (2)
5910 890 3100 so that one clamp
screw engages the inner 10 mm
hole (1) in the assembly stand.
1 2 3
376RA000TG
To service the underside of the
machine (e.g. remove the front
handle), turn the machine upside
down and mount it so that one
clamp screw engages the outer
10 mm hole (1) in the assembly
stand.
Always use original STIHL
replacement parts.
They can be identified by the
STIHL part number, the STIH)
logo and the STIHL parts
symbol ( . The symbol may also
appear alone on small parts.
1. Introduction
4. 3TS 700, TS 800
Specific national safety regulations
and the safety instructions in the
instruction manual must be
observed if the machine has to be
started up during maintenance or
repair work.
Petrol is highly inflammable and can
also be explosive under certain
conditions.
Improper handling may result in
burns and other serious injuries.
Important!
Do not bring any fire, flame, spark or
other source of heat near the fuel.
All work with fuel must be performed
outdoors only. Spilled fuel must be
wiped away immediately.
2. Safety precautions
5. 4 TS 700, TS 800
3. Specifications
3.1 Power unit
TS 700, TS 800
Displacement: 98.5 cm3
Bore: 56 mm
Stroke: 40 mm
Engine power to ISO 7293: 5.0 kW (6.8 HP)
at 9300 rpm
Nominal spindle speed 4620 rpm
Idle speed: 2200 rpm
Clutch: Centrifugal clutch without linings
Clutch engages at: 3200 rpm
Crankcase leakage test
at excess pressure: pü = 0.5 bar
under vacuum: pu = 0.5 bar
3.2 Fuel system
Carburetor leakage test at
excess pressure: pü = 0.8 bar
Operation of tank vent at
excess pressure: pü = 0.3 bar
Fuel: as specified in instruction
manual
3.3 Ignition system
Air gap between ignition
module and fanwheel: 0.15...0.3 mm
Spark plug (interference
suppressed):
Bosch WSR 6F
NGK BPMR 7 A
Electrode gap: 0.5 mm
6. 5TS 700, TS 800
3.4 Abrasive wheels
TS 700
Composite and diamond abrasive wheels Diameter 350 mm
Cutting depth approx. 123.5 mm
TS 800
Composite and diamond abrasive wheels Diameter 400 mm
Cutting depth approx. 143 mm
3.5 Special accessories
Cart FW 20
Cutting direction indicator
Water container kit
Pressurized water container kit
7. 6 TS 700, TS 800
3.6 Tightening torques
Screws can be removed and installed as often as necessary without impairing the strength of the screwed
assembly, provided that the specified tightening torque is observed.
For this reason, it is essential to use a torque wrench.
Fastener Thread
size
For component Tightening
torque (Nm)
Remarks
Screw IS-M 5x20 Starter cover / crankcase 6.0
Screw IS-M 5x58x22 Clamp / handlebar holder 5.0
Screw IS-P 4x14 Bearing, switch shaft / tank housing 2.5
Screw IS-M 5x21 Filter cover and spark plug cover 3.5
Screw IS-M 5x20 Crankcase 9.0
Nut M5 Filter base / carburetor 3.5
Screw IS-M 5x16 Cover, tensioner / cast arm 4.0
Screw IS-P 6x19 Handlebar / tank housing 6.0
Screw IS-M 5x20 Air guide shroud / crankcase 4.0
Screw IS-M 5x20 Muffler / crankcase 10.0 1)
Screw IS-M 5x20 Muffler / cylinder 10.0
Screw IS-M 4x8 Short-circuit lead / crankcase 3.0
Screw IS-P 6x19 Filter base / tank housing 5.0
Screw IS-M 5x35x12 Filter housing / filter base 3.0
Screw IS-P 5x19 Shroud / tank housing 6.0
Screw M 10x1 L Belt pulley / shaft 40.0
Screw IS-M 5x20 Fan cover / crankcase 6.0
Screw IS-M 5x20 Starter cover / crankcase 6.0
Screw IS-M 6x35 Cylinder / crankcase 12.0 1)
Screw IS-M 4x10 Cylinder / support plate diaphragm 3.0 1)
Screw IS-M 5x20 Ignition module / crankcase 8.0 2)
Screw IS-P 6x32.5 Support / handlebar / tank housing 6.0
Screw IS-M 6x16 Holder for shutoff valve / water
connection
4.0
Screw IS-M 6x35 AV element rubber buffer / front handle 6.0
Screw IS-P 6x19 AV element rubber buffer / ignition side 6.0
Screw IS-P 6x19 AV element rubber buffer / clutch side 6.0
Screw IS-M 5x20 Bearing plug / spring 6.0
Screw IS-P 3x6 Rewind spring / starter cover 0.5
Screw IS-M 3x20 Hose clip / manifold 0.8
Screw IS-D 5x16 Rubber buffer / support 6.0
Nut M 10x1 Flywheel 40.0
Nut M 10x1 Starter wheel 45.0
Carrier M 14x1 L Clutch 50.0
M 14x1.25 Spark plug 28.0
Nut M 10x1 L Belt pulley / bearing 40.0
Screw IS-M 6x28 Bearing flange / guard 8.0
Screw M 10x18 Thrust washer / abrasive wheel 20.0
Nut M 10x18 Abrasive wheel 30.0
M 10x1 Decompression valve 14.0
8. 7TS 700, TS 800
Remarks:
1) Secure screw with Loctite 270.
2) Place a washer under the screw head.
Note:
Screwdriver speed when used in plastic material: Plastoform screws max. 600 rpm.
9. 8 TS 700, TS 800
4. Troubleshooting
4.1 Clutch
Problem Cause Remedy
Abrasive wheel stops under load at
full throttle
Clutch shoes badly worn Install new clutch
Clutch drum badly worn Install new clutch drum
Abrasive wheel rotates at idle
speed
Idle speed too high Readjust with idle speed screw LA
(anticlockwise)
Clutch springs stretched or fatigued Replace clutch springs or install
new clutch
Clutch spring hooks broken Replace clutch springs
Loud noises Clutch springs stretched or fatigued Replace all clutch springs
Deep groove ball bearing on belt
pulley damaged
Replace deep groove ball bearing
Clutch shoe retainer broken Fit new retainer
Clutch shoes and carrier worn Install new clutch
10. 10 TS 700, TS 800
4.3 Ignition system
Important:
Exercise extreme caution while
carrying out maintenance and repair
work on the ignition system. The
high voltages which occur can
cause serious or fatal accidents.
Problem Cause Remedy
Engine runs roughly, misfires,
temporary loss of power
Spark plug boot is loose Press boot firmly onto spark plug
and fit new spring if necessary
Spark plug sooted, smeared with oil Clean the spark plug or replace if
necessary
Incorrect air gap between ignition
module and flywheel
Set air gap correctly
Flywheel cracked or has other
damage or pole shoes have turned
blue
Install new flywheel
Ignition timing wrong, flywheel out
of adjustment, key in flywheel has
sheared off
Install new flywheel
Weak magnetization in flywheel -
pole shoes have turned "blue"
Install new flywheel
Irregular spark Check operation of master control
lever and ignition module
Faulty insulation on ignition lead or
short circuit wire. Use ohmmeter to
check ignition lead for break. If
break is detected or high resistance
measured, fit a new ignition lead
Check operation of spark plug
Clean the spark plug or replace if
necessary
Crankcase damaged (cracks) Replace crankcase
11. 11TS 700, TS 800
4.4 Carburetor
Problem Cause Remedy
Carburetor floods; engine stalls Inlet needle not sealing - impurities
in valve seat or cone damaged
Remove and clean or replace the
inlet needle, clean the fuel tank,
pick-up body and fuel line if
necessary
Inlet control lever sticking on
spindle
Restore easy movement of inlet
control lever
Helical spring not located on nipple
of inlet control lever
Remove the inlet control lever and
refit it correctly
Perforated disc on diaphragm is
deformed and presses constantly
against the inlet control lever
Fit a new metering diaphragm
Inlet control lever too high (relative
to correct installed position)
Set inlet control lever flush with top
edge of housing
Poor acceleration Idle jet too lean Turn low speed screw L
anticlockwise (richer), no further
than stop
Main jet too lean Turn high speed screw H
anticlockwise (richer), no further
than stop
Inlet control lever too low (relative
to correct installed position)
Set inlet control lever flush with top
edge of housing
Inlet needle sticking to valve seat Remove inlet needle, clean and
refit
Diaphragm gasket leaking Fit new diaphragm gasket
Metering diaphragm damaged or
shrunk
Fit new metering diaphragm
Impulse hose damaged or kinked Fit new impulse hose
12. 12 TS 700, TS 800
Problem Cause Remedy
Engine will not idle, idle speed too
high
Throttle shutter opened too wide by
idle speed screw LA
Reset idle speed screw LA
correctly
Oil seals / crankcase leaking Seal or replace oil seals /
crankcase
Engine stops when idling Idle jet bores or ports blocked Clean the carburetor
Idle jet too rich or too lean Set low speed screw L correctly
Setting of idle speed screw
incorrect - throttle shutter
completely closed
Reset idle speed screw LA
correctly
Small plastic plate in valve jet
does not close
Clean or renew valve jet
13. 13TS 700, TS 800
Problem Cause Remedy
Engine speed drops quickly under
load - low power
Air filter dirty Clean the air filter
Throttle shutter not opened fully Check linkage
Tank vent faulty Clean tank vent or replace if
necessary
Fuel pick-up body dirty Clean the pick-up body, fit a new
filter
Fuel strainers dirty Replace the fuel strainers
Leak in fuel line between tank and
fuel pump
Seal connections or install a new
fuel line
Setting of high speed screw H too
rich
Turn the high speed adjusting
screw H clockwise (leaner) – max.
up to the stop.
Main jet bores or ports blocked Clean the carburetor
Pump diaphragm damaged or
fatigued
Fit new pump diaphragm
Impulse hose damaged or kinked Fit new impulse hose
14. 14 TS 700, TS 800
4.5 Power unit
Always check and, if necessary,
repair the following parts before
looking for faults on the engine:
– Air filter
– Fuel system
– Carburetor
– Ignition system
Problem Cause Remedy
Engine does not start easily, stalls
at idle speed but operates normally
at full throttle
Oil seals in crankgear damaged Replace the oil seals
Crankcase leaking or damaged
(cracks)
Seal or replace the crankcase
Engine does not deliver full power
or runs erratically
Piston rings worn or broken Replace piston rings
Muffler / spark arresting screen
carbonized
Clean the muffler (inlet and
exhaust), replace spark arresting
screen, replace muffler if necessary
Air filter dirty Replace air filter
Fuel / impulse hose severely kinked
or damaged
Fit new hoses and route them
without kinks
Decompression valve sticking Replace the decompression valve
Engine overheating Insufficient cylinder cooling. Air
inlets in fan housing blocked or
cooling fins on cylinder very dirty
Thoroughly clean all cooling air
openings and the cylinder fins
15. 15TS 700, TS 800
– Test radial and axial truth of
running, b 5.2
: Release hose clip (1), remove
hose retainer (2) and disconnect
hose (3).
During installation, ensure that the
2
1
3
376RA001TG
hose clip (1) does not touch the
handlebar.
: Relax the ribbed V-belt by turning
the hexagon of the tensioner
anticlockwise until the arrow
points to the left (to "0").
376RA003TG
: Remove screws (1) from bearing
and remove guard.
376RA004TG
1
1
: Unhook the ribbed V-belt (1) from
the belt pulley and remove the
bearing with guard.
1
376RA017TG
: Remove screw (1) from the thrust
washer (2).
– Remove the thrust washer.
2
338RA005VA
1
: Remove axial clamping ring from
the shaft.
: Remove thrust washer (1).
1
376RA016TG
: Block the belt pulley (arrow).
: Unscrew the nut (left-hand
thread) and remove the belt
pulley.
376RA018TG
: Remove the key (1) from the
groove in the shaft.
: Remove the washer (2) from the
shaft.
2
1
376RA012TG
5. Abrasive wheel drive
5.1 Bearing with guard
16. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 16 TS 700, TS 800
: Draw the shaft (1) out of the deep
groove ball bearings.
1
376RA011TG
: Unscrew the four screws (1) and
remove them with the
compression springs (2) and
sleeves.
1
2
376RA013TG
: Remove the flange.
338RA011VA
: Remove the washer with rubber
ring.
338RA012VA
: Pull the bearing (1) out of the
rubber ring.
1
376RA014TG
: Remove the washer (1) and
rubber ring (2).
1
2
376RA015TG
: Remove the circlips in front of the
deep groove ball bearings from
the grooves on both sides.
Note:
Use pliers with short rounded tips.
376RA009TG
: Press both deep groove ball
bearings and the ring out of the
bearing with a drift pin (1)
4224 893 7200.
– Reassemble the parts in reverse
order.
1
376RA006TG
Note:
Particular attention must be paid to
the following steps.
: Fit a circlip in a groove in the
bearing.
376RA010TG
18. 17TS 700, TS 800
– Align the deep groove ball
bearings with the closed sides
facing outwards.
: Slide the first deep groove ball
bearing (1), the ring (2) and the
second deep groove ball
bearing (3) onto the shaft.
1
2
3
376RA019TG
: Position the deep groove ball
bearings and press them home
with the drift pin (1)
4224 893 7200 until they make
contact with the circlip.
– Draw the assembly pin out of the
deep groove ball bearings.
1
376RA007TG
– Fit the second circlip in the
groove in the bearing.
Note:
The seal on the deep groove ball
bearing must not be damaged.
: Lay the washer (1) over the
bearing.
– Insert the bearing in the rubber
bearing from the outside.
1
376RA008TG
: Lay a washer over the flange.
– Insert the flange from the inside.
Note:
The rubber rings must also be
aligned with the contours of the
guard.
338RA022VA
: Slide the sleeve (1) and spring (2)
onto the screw (3).
– Insert and tighten down the
screws.
338RA023VA
2 1 3
– Slide the washer onto the shaft
and fit the key.
: Slide the belt pulley (1) onto the
shaft with the longer collar
(arrow) first.
– Fit the washer and nut, screw the
1
376RA002TG
nut down tightly.
– Tightening torques, b 3.6
: Fit the thrust washer so that the
groove (arrow) is aligned with the
lug.
– Fit the axial clamping ring.
338RA025VA