Jefferson Brooks III is a welder and ironworker seeking a challenging position. He has over 15 years of welding experience with stick, flux, and mig welding. Brooks has worked in various roles including as a welder, ironworker, CDL driver, and machinist/welder over the past 19 years. He is responsible and focused on safety.
1. Jefferson Brooks III
11203 Northam Dr Tomball, Tx. 77375
(832)375-4897, (832)795-9373, (832)329-6219
jeffersonbrooksiii@yahoo.com
Objective:
To obtain a challenging position that offers the opportunity to utilize and prove my skills and experience. I look
forward to enhancing my managerial skills by working in an environment that encourages professional growth and
personal investment.
Experience:
Welder/Ironworker, International Tradesmen; Houston, Tx. 08/2016 - present
First off, Responsible for the safety of ourself and others around, duties were to tear down rails, ladders, walk ways,
floors etc..... rig up machinery to be taken out with a 40 thousand tone trolley. Used chain fall for smaller object.
Chain hoist to line up and level heavy equipment. Weld I-Beams using flux, mig, and or stick. Responsible
for housekeeping as well.
Tank Welder/Ironworker, Willbros Downstream Tulsa, Ok. 11/14 - 05/16
Responsible for safety first then overlook the project which was being worked on.Layout floor sheets, and weld using
jet rods.Welded nuts to shell to put T-Plats on using bullpens and a sledge hammer to knock bullpen in place to hold
T-Plat so shell would stay in place. Once shell was in place, verts would be welded by hand with Flux, Stick or the
buggo. Housekeeping was a major role in staying safe from slips, trips, and falls.
Tankwelder/Ironworker, STS, Laporte, Tx. 01/14 - 11/14
Responsible for safety first then overlook the project which was being worked on.Layout floor sheets,and weld using
jet rods.Welded nuts to shell to put T-Plats on using bullpens and a sledge hammer to knock bullpen in place to hold
T-Plat so shell would stay in place. Once shell was in place, verts would be welded by hand with Flux, Stick or the
buggo. Also repaired used tanks and cut old pieces out using a torch from 2' to 5' torch and Housekeeping was a
major role in staying safe from slips, trips, and falls.
Flux welder, Spooltech, Houston, Tx 03/13 - 01/14
Responsible for fitting and welding spools using flux and some m ig. Getting in and out of tight spaces to weld. Used
overhead crane for movementof spool. Fit and tacked spool then welded using all fluxand kept good house keeping.
CDL Driver/Marten Transportation 07/07 - 01/11 OnTime Transportation 01/11 - 12/12
Responsible for delivering freightcross country in a timelymanner.Traveled all 48 states and Canada.Did inspection
on Truck daily to make sure it was running good and kept it in good condition. Did log books daily when on duty and
kept truck and trailer cleaned washed when there was no load waiting to be dispatched.
Maintenance Welder/Jindal 01/04 - 07/07 Baytown, tx
Responsible for keeping machines running good and 7018 rods to weld rings that go inside pipes for when pipes
bump up againsteach other. Welded the blaster thatcleaned pipe using stainless steel. Welded I-beams which hold
pipes and welded pipes when needed to with flux. Did Aluminum welding from time to time.
Education: Crosby High School Crosby, Tx./Diploma, Gary Job Corps San Marcus, Tx./Machinist, Sparks Academy
Houston, Tx. Welding.
Skills: 15yrs plus of welding with Stick, Flux, and Mig, 5yrs Ironworker, 17yrs CDL Driver, 19yr machinist/ Marten
Transport: Driver 6yrs, Jindal: Welder 3yrs, Peakload: Machinist/welder 4yrs
References: Ralph Cavazos, Houston, Tx. Anthony Smith, Iowa, Jeff Powell, Louisiana