This document is a service manual for New Holland T7 series tractors models T7.220, T7.235, T7.250, T7.260, and T7.270. It provides specifications and repair/replacement instructions for major components including the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. The manual is intended to assist technicians in servicing and repairing components of the T7 tractors.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualfujsefxdeksemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and side counterweights. The counterweight is removed using an eyebolt and lifting device. Fenders are removed using eyebolts through mount holes and lifted away. The hood assembly can be pivoted or completely removed using a lifting device attached to the spine. The hydraulic tank is removed by disconnecting hoses, removing mounting hardware, and lifting it away while supported.
Hyster c008 (h370 c) forklift service repair manualfujsefxdeksemm
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from outlet oil.
Hyster b187 (s50 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Hyster b187 (s40 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...fujsefxdeksemm
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...fujsefxdeksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...fujsefxdeksemm
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It outlines the required tools and safety precautions, and gives step-by-step instructions to release pressure, remove hoses and bolts, and disassemble internal components like springs and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...fujsefxdeksemm
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualfujsefxdeksemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and side counterweights. The counterweight is removed using an eyebolt and lifting device. Fenders are removed using eyebolts through mount holes and lifted away. The hood assembly can be pivoted or completely removed using a lifting device attached to the spine. The hydraulic tank is removed by disconnecting hoses, removing mounting hardware, and lifting it away while supported.
Hyster c008 (h370 c) forklift service repair manualfujsefxdeksemm
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from outlet oil.
Hyster b187 (s50 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Hyster b187 (s40 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...fujsefxdeksemm
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...fujsefxdeksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...fujsefxdeksemm
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It outlines the required tools and safety precautions, and gives step-by-step instructions to release pressure, remove hoses and bolts, and disassemble internal components like springs and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...fujsefxdeksemm
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...fujsefxdeksemm
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...fujsefxdeksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. It describes:
1) Removing the fuel injection lines, oil supply/drain lines, heat shield, and other components to access the pump housing.
2) Using various tools like bolts, washers, and pullers to remove the pump housing mounting bolts, nuts, and center bolt to detach the housing.
3) Lifting the housing off the engine using a sling and removing O-rings from the housing and governor.
4) Reversing the removal process to reinstall the housing, ensuring proper alignment and torque of mounting hardware.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)fujsefxdeksemm
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and gives step-by-step instructions to remove components like the rear housing, pinion drive, shift lever, brushes, and field winding coil. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualfujsefxdeksemm
This document provides instructions for disassembling and assembling starting motors for Caterpillar excavators. It describes the process for three starting motor models: 37-MT, 41-MT and 42-MT. The disassembly process involves removing components like the solenoid, rear housing, pinion drive housing, shift lever housing and field winding coil. The assembly process describes installing these components in reverse order while applying lubricants to bushings and torquing screws correctly.
The document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly that remove parts like the fuel ratio control, housing, springs, pins, seals, and more. It then lists 33 steps for assembly that install these parts in reverse order, noting to clean parts and apply oil before assembling. Tools like retaining ring pliers and drivers are required for some steps. Precise alignment and positioning of parts is emphasized during assembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for disassembling the piston motor of a 216B3 Skid Steer Loader. It outlines 25 steps to remove components such as nuts, valves, springs, pistons, seals, bearings, gears and more. Precautions are included to release spring forces safely. Required tools include retaining ring pliers, drivers, pullers and presses. Detailed illustrations accompany each step for clarity.
Case ih stx 380 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine systems, air induction systems, electrical systems, steering systems, and removal/installation of engines. It also lists recommended engine service manuals for different engine models used in the tractors.
Case ih steiger 535 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih steiger 430 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih puma 220 tier 4 b (final) tractor service repair manualfujsefxdeksemm
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 921 g wheel loader xr eh, new cab, tier 4b, multipurpose wheel loader se...fujsefxdeksemm
This document is a service manual that provides specifications and repair instructions for wheel loaders. It includes sections on the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, and electrical systems. The introduction provides safety information for working on the machine. The manual contains detailed part numbers, diagrams, and troubleshooting steps for maintenance and repairs.
Case 921 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document is a service manual for a 921E wheel loader. It contains sections covering general information, engines, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment. Each section provides removal and installation instructions for components, specifications, troubleshooting information, and other repair details. The manual also includes torque specifications, fluid and lubricant information, and electrical and hydraulic schematic diagrams in the rear.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
Case 721 g xt eh, new cab tier2 wheel loader service repair manual [fnh0721...fujsefxdeksemm
This document provides specifications for the engines in CNH Industrial 621G and 721G wheel loaders, including:
- Engine idle speeds and maximum no load RPM ranges
- Torque converter and hydraulic stall speed ranges
- Recommended temperature ranges for torque converter oil and hydraulic oil
It also notes the engine configuration (4 or 5 speed transmission) and indicates applicable regions.
Case 721 f xt wheel loader service repair manualfujsefxdeksemm
The document provides service information for a wheel loader, including:
- An overview of engine specifications for different transmission configurations.
- Part numbers for the engine service manual in multiple languages.
- Instructions to remove the engine, which involve draining fluids, disconnecting hoses, and using straps to lift the hood and engine out.
Case 721 f tier 4 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a 721F wheel loader. The main steps include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting bolts. Safety precautions are described such as releasing pressure from hydraulic and brake systems. Key components removed are the radiator, hood, air intake components, exhaust, and belt cover. Proper lifting and support equipment is required.
Case 721 e eu wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing and installing the engine and radiator on a 721E wheel loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an engine lift to remove the engine from the loader. Engine installation is the reverse of removal. Radiator removal requires draining the coolant and removing mounting bolts, hoses and electrical connections. Radiator installation is the reverse of removal.
New holland w110 d tier 2 wheel loader service repair manualfujsefxdeksemm
This document is a service manual that provides instructions for removing the engine from a W110D Wheel Loader. It outlines 23 steps to remove the engine, including draining fluids, disconnecting wiring harnesses and cables, removing protective panels, and loosening mounting bolts. The manual emphasizes safety precautions and contains diagrams to illustrate each step in the removal process.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...fujsefxdeksemm
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...fujsefxdeksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. It describes:
1) Removing the fuel injection lines, oil supply/drain lines, heat shield, and other components to access the pump housing.
2) Using various tools like bolts, washers, and pullers to remove the pump housing mounting bolts, nuts, and center bolt to detach the housing.
3) Lifting the housing off the engine using a sling and removing O-rings from the housing and governor.
4) Reversing the removal process to reinstall the housing, ensuring proper alignment and torque of mounting hardware.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)fujsefxdeksemm
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and gives step-by-step instructions to remove components like the rear housing, pinion drive, shift lever, brushes, and field winding coil. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualfujsefxdeksemm
This document provides instructions for disassembling and assembling starting motors for Caterpillar excavators. It describes the process for three starting motor models: 37-MT, 41-MT and 42-MT. The disassembly process involves removing components like the solenoid, rear housing, pinion drive housing, shift lever housing and field winding coil. The assembly process describes installing these components in reverse order while applying lubricants to bushings and torquing screws correctly.
The document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly that remove parts like the fuel ratio control, housing, springs, pins, seals, and more. It then lists 33 steps for assembly that install these parts in reverse order, noting to clean parts and apply oil before assembling. Tools like retaining ring pliers and drivers are required for some steps. Precise alignment and positioning of parts is emphasized during assembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for disassembling the piston motor of a 216B3 Skid Steer Loader. It outlines 25 steps to remove components such as nuts, valves, springs, pistons, seals, bearings, gears and more. Precautions are included to release spring forces safely. Required tools include retaining ring pliers, drivers, pullers and presses. Detailed illustrations accompany each step for clarity.
Case ih stx 380 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine systems, air induction systems, electrical systems, steering systems, and removal/installation of engines. It also lists recommended engine service manuals for different engine models used in the tractors.
Case ih steiger 535 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih steiger 430 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih puma 220 tier 4 b (final) tractor service repair manualfujsefxdeksemm
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 921 g wheel loader xr eh, new cab, tier 4b, multipurpose wheel loader se...fujsefxdeksemm
This document is a service manual that provides specifications and repair instructions for wheel loaders. It includes sections on the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, and electrical systems. The introduction provides safety information for working on the machine. The manual contains detailed part numbers, diagrams, and troubleshooting steps for maintenance and repairs.
Case 921 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document is a service manual for a 921E wheel loader. It contains sections covering general information, engines, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment. Each section provides removal and installation instructions for components, specifications, troubleshooting information, and other repair details. The manual also includes torque specifications, fluid and lubricant information, and electrical and hydraulic schematic diagrams in the rear.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
Case 721 g xt eh, new cab tier2 wheel loader service repair manual [fnh0721...fujsefxdeksemm
This document provides specifications for the engines in CNH Industrial 621G and 721G wheel loaders, including:
- Engine idle speeds and maximum no load RPM ranges
- Torque converter and hydraulic stall speed ranges
- Recommended temperature ranges for torque converter oil and hydraulic oil
It also notes the engine configuration (4 or 5 speed transmission) and indicates applicable regions.
Case 721 f xt wheel loader service repair manualfujsefxdeksemm
The document provides service information for a wheel loader, including:
- An overview of engine specifications for different transmission configurations.
- Part numbers for the engine service manual in multiple languages.
- Instructions to remove the engine, which involve draining fluids, disconnecting hoses, and using straps to lift the hood and engine out.
Case 721 f tier 4 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a 721F wheel loader. The main steps include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting bolts. Safety precautions are described such as releasing pressure from hydraulic and brake systems. Key components removed are the radiator, hood, air intake components, exhaust, and belt cover. Proper lifting and support equipment is required.
Case 721 e eu wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing and installing the engine and radiator on a 721E wheel loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an engine lift to remove the engine from the loader. Engine installation is the reverse of removal. Radiator removal requires draining the coolant and removing mounting bolts, hoses and electrical connections. Radiator installation is the reverse of removal.
New holland w110 d tier 2 wheel loader service repair manualfujsefxdeksemm
This document is a service manual that provides instructions for removing the engine from a W110D Wheel Loader. It outlines 23 steps to remove the engine, including draining fluids, disconnecting wiring harnesses and cables, removing protective panels, and loosening mounting bolts. The manual emphasizes safety precautions and contains diagrams to illustrate each step in the removal process.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Link Product / Engine
Product Market Product Engine
T7.220 Power Command North America F4DFE613L*A
T7.235 Power Command North America F4DFE613K*A
T7.250 Power Command North America F4DFE613J*A
T7.260 Power Command North America F4DFE613H*A
T7.235 AutoCommand North America F4DFE613K*A
T7.250 AutoCommand North America F4DFE613J*A
T7.260 AutoCommand North America F4DFE613H*A
T7.270 AutoCommand North America F4DFE613G*A
47524342 29/05/2013
3. Contents
INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase ............................................................. 10.1
[10.102] Pan and covers .................................................................... 10.2
[10.216] Fuel tanks .......................................................................... 10.3
[10.210] Lift pump and lines ................................................................. 10.4
[10.218] Fuel injection system............................................................... 10.5
[10.250] Turbocharger and lines............................................................. 10.6
[10.254] Intake and exhaust manifolds and muffler ......................................... 10.7
[10.500] Selective Catalytic Reduction (SCR) exhaust treatment ........................... 10.8
[10.400] Engine cooling system ............................................................. 10.9
[10.414] Fan and drive .................................................................... 10.10
[10.408] Oil cooler and lines............................................................... 10.11
Transmission.............................................................................. 21
[21.113] Powershift transmission ............................................................ 21.1
[21.155] Powershift transmission internal components...................................... 21.2
[21.160] Creeper ............................................................................ 21.3
[21.166] Overdrive........................................................................... 21.4
[21.504] Continuously Variable Transmission (CVT) ........................................ 21.5
[21.505] Continuously Variable Transmission (CVT) external controls...................... 21.6
[21.506] Continuously Variable Transmission (CVT) lubrication system .................... 21.7
[21.507] Continuously Variable Transmission (CVT) internal components.................. 21.8
[21.109] Transmission cooler and lines...................................................... 21.9
Four-Wheel Drive (4WD) system .................................................. 23
[23.202] Electro-hydraulic control ........................................................... 23.1
[23.314] Drive shaft.......................................................................... 23.2
Front axle system ....................................................................... 25
47524342 29/05/2013
4. [25.100] Powered front axle ................................................................. 25.1
[25.102] Front bevel gear set and differential ............................................... 25.2
[25.108] Final drive hub, steering knuckles, and shafts ..................................... 25.3
[25.122] Axle suspension control............................................................ 25.4
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
[27.106] Rear bevel gear set and differential................................................ 27.2
[27.120] Planetary and final drives .......................................................... 27.3
Power Take-Off (PTO)................................................................. 31
[31.101] Rear mechanical control ........................................................... 31.1
[31.104] Rear electro-hydraulic control...................................................... 31.2
[31.114] Two-speed rear Power Take-Off (PTO) ............................................ 31.3
[31.116] Three-speed rear Power Take-Off (PTO) .......................................... 31.4
[31.119] Four-speed rear Power Take-Off (PTO)............................................ 31.5
[31.146] Front Power Take-Off (PTO) ....................................................... 31.6
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
[33.110] Parking brake or parking lock ...................................................... 33.2
[33.220] Trailer brake hydraulic control...................................................... 33.3
[33.224] Trailer brake pneumatic control .................................................... 33.4
[33.350] Anti-lock Brake System (ABS) ..................................................... 33.5
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.300] Reservoir, cooler, and filters........................................................ 35.2
[35.106] Variable displacement pump ....................................................... 35.3
[35.102] Pump control valves................................................................ 35.4
[35.105] Charge pump....................................................................... 35.5
[35.322] Regulated/Low pressure system ................................................... 35.6
47524342 29/05/2013
5. [35.204] Remote control valves ............................................................. 35.7
[35.220] Auxiliary hydraulic pump and lines ................................................. 35.8
[35.114] Three-point hitch control valve ..................................................... 35.9
[35.160] Front hitch controls and lines .................................................... 35.10
[35.162] Front hitch cylinders and lines ................................................... 35.11
Pneumatic system ...................................................................... 36
[36.100] Pneumatic system.................................................................. 36.1
Hitches, drawbars, and implement couplings.................................. 37
[37.120] Rear three-point hitch linkage...................................................... 37.1
[37.162] Front hitch.......................................................................... 37.2
[37.110] Rear three-point hitch .............................................................. 37.3
[37.106] Automatic pickup hitch ............................................................. 37.4
Frames and ballasting ................................................................. 39
[39.100] Frame .............................................................................. 39.1
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
[41.106] Tie rods............................................................................. 41.2
[41.200] Hydraulic control components...................................................... 41.3
[41.216] Cylinders ........................................................................... 41.4
[41.432] Autoguidance steering ............................................................. 41.5
Wheels...................................................................................... 44
[44.511] Front wheels........................................................................ 44.1
[44.520] Rear wheels........................................................................ 44.2
Cab climate control ..................................................................... 50
[50.100] Heating ............................................................................. 50.1
[50.104] Ventilation .......................................................................... 50.2
[50.200] Air conditioning..................................................................... 50.3
Electrical systems....................................................................... 55
47524342 29/05/2013
6. [55.610] Ground speed control .............................................................. 55.1
[55.000] Electrical system ................................................................... 55.2
[55.100] Harnesses and connectors......................................................... 55.3
[55.015] Engine control system.............................................................. 55.4
[55.301] Alternator........................................................................... 55.5
[55.302] Battery.............................................................................. 55.6
[55.988] Selective Catalytic Reduction (SCR) electrical system ............................ 55.7
[55.640] Electronic modules ................................................................. 55.8
[55.513] Cab transmission controls.......................................................... 55.9
[55.024] Transmission control system..................................................... 55.10
[55.020] Transmission speed sensors..................................................... 55.11
[55.021] Transmission pressure sensors .................................................. 55.12
[55.022] Transmission temperature sensors .............................................. 55.13
[55.045] Front axle control system ........................................................ 55.14
[55.048] Rear Power Take-Off (PTO) control system ..................................... 55.15
[55.049] Front Power Take-Off (PTO) control system ..................................... 55.16
[55.031] Parking brake electrical system .................................................. 55.17
[55.035] Remote control valve electric control ............................................ 55.18
[55.051] Cab Heating, Ventilation, and Air-Conditioning (HVAC) controls................. 55.19
[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system............... 55.20
[55.047] Steering control system .......................................................... 55.21
[55.523] Cab hitch controls ................................................................ 55.22
[55.130] Rear three-point hitch electronic control system ................................. 55.23
[55.911] Global Positioning System (GPS) ................................................ 55.24
[55.680] Autopilot/Autoguidance .......................................................... 55.25
[55.408] Warning indicators, alarms, and instruments .................................... 55.26
[55.350] Anti-lock Brake System (ABS) electrical system ................................. 55.27
[55.032] Trailer brake electrical system ................................................... 55.28
[55.030] Service brake electrical system .................................................. 55.29
47524342 29/05/2013
9. INTRODUCTION
Foreword - How to use and navigate through this manual
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through web delivery (eTIM), DVD, and paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on their machine it is usually because a function or system on their ma-
chine is not working at all, is not working efficiently, or is not responding correctly to their commands. When you refer
to the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system, you will then find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies, and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system: the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting), and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - the component or function on the machine, that the piece of technical information is going to describe
(e.g., Fuel tank).
• INFORMATION TYPE - the piece of technical information that has been written for a particular component or func-
tion on the machine (e.g., Capacity would be a type of Technical Data describing the amount of fuel held by the fuel
tank).
• PRODUCT - the model for which the piece of technical information is written.
Every piece of technical information will have those three categories attached to it. You will be able to use any combi-
nation of those categories to find the right piece of technical information you need to resolve that customer's concern
on their machine.
That information could be:
• the procedure for how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
47524342 29/05/2013
4
10. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual and on machine decals, you will find the signal words DANGER, WARNING, and CAUTION
followed by special instructions. These precautions are intended for the personal safety of you and those working
with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. The
color associated with DANGER is RED.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
The color associated with WARNING is ORANGE.
CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result
in minor or moderate injury. The color associated with CAUTION is YELLOW.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage. The color
associated with Notice is BLUE.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47524342 29/05/2013
9
11. SERVICE MANUAL
Engine
T7.220 AutoCommand , T7.220 Power Command , T7.235 AutoCommand ,
T7.235 Power Command , T7.250 AutoCommand , T7.250 Power Command ,
T7.260 AutoCommand , T7.260 Power Command , T7.270 AutoCommand
47524342 29/05/2013
10
12. Engine - Engine and crankcase
Engine - Disconnect
Prior operation:
Remove the battery, for further information refer to Battery - Remove (55.302)
Prior operation:
Drain the engine coolant, for further information refer to Engine cooling system - Drain fluid (10.400)
Prior operation:
Discharge the air conditioning system, for further information refer to Air conditioning - Discharging (50.200)
Prior operation:
Remove the selective catalytic reduction (SCR) exhaust line, for further information refer to Exhaust pipes - Remove
(10.254)
Prior operation:
Remove the front AoH converter, for further information refer to Air-over-Hydraulic (AoH) converter - Remove
(33.350)
Prior operation:
Remove the front wheels, for further information refer to Front wheels - Remove (44.511)
WARNING
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply could result in death or seri-
ous injury.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your
hands or fingers between parts. Use Personal
Protective Equipment (PPE) as indicated in this
manual, including protective goggles, gloves,
and safety footwear.
Failure to comply could result in death or seri-
ous injury.
W0208A
1. Using suitable lifting equipment support the front
weights.
BAIL07APH062AVA 1
47524342 29/05/2013
10.1 [10.001] / 7
13. Engine - Engine and crankcase
2. Disconnect and remove the front weights from the
weight carrier.
BAIL07APH063AVA 2
3. Disconnect the air conditioning hoses (1) and detach
the bracket (2).
NOTE: Cap all open connections to prevent contamination
of the system.
BAIL12ABS131AVA 3
4. Detach the air conditioning pipe bracket from the en-
gine frame.
BAIL11CCM027AVA 4
5. Remove the front AoH bracket lower bolts.
BAIL12ABS132AVA 5
47524342 29/05/2013
10.1 [10.001] / 8
14. Engine - Engine and crankcase
6. Detach the pipe bracket and remove the AoH
bracket.
BAIL12ABS133AVA 6
7. Disconnect the brake valve supply hose (if fitted).
BAIL11CCM031AVA 7
8. Disconnect the flywheel position sensor electrical
connector.
BAIL11CCM022AVA 8
9. Disconnect the steering hoses.
NOTE: Make a note of the position of the hoses to aid in-
stallation.
BAIL11CCM028AVA 9
47524342 29/05/2013
10.1 [10.001] / 9
15. Engine - Engine and crankcase
10. Disconnect the fuel supply and return lines.
BAIL11CCM283AVA 10
11. Disconnect the diff lock and suspension pipes.
BAIL12ABS134AVA 11
12. Disconnect the trailer brake air supply pipe.
BAIL08CVT135AVA 12
13. Disconnect the heater supply hose from the rear of
the engine cylinder head.
BAIL12ABS135AVA 13
47524342 29/05/2013
10.1 [10.001] / 10
16. Engine - Engine and crankcase
14. Disconnect the steering hydraulic oil supply pipe.
BAIL11CCM035AVA 14
15. Disconnect the SCR coolant control valve electrical
connector.
BAIL10CVT410AVB 15
16. Disconnect the coolant line connectors from the SCR
coolant control valve.
BAIL10CVT412AVB 16
17. Detach the cab heater hose retaining bracket.
BAIL12ABS136AVA 17
47524342 29/05/2013
10.1 [10.001] / 11
17. Engine - Engine and crankcase
18. Disconnect the engine harness electrical connector.
BAIL12ABS137AVA 18
19. Disconnect the cab electrical connectors.
BAIL07APH058AVB 19
20. Disconnect the electrical connector and cut the cable
tie.
BAIL12ABS138AVA 20
21. Disconnect the radar electrical connector (1) and re-
move the radar (2).
BAIL12ABS139AVA 21
47524342 29/05/2013
10.1 [10.001] / 12
18. Engine - Engine and crankcase
22. Remove the flywheel speed sensor and disconnect
the heater return hose.
BAIL12ABS140AVA 22
23. Disconnect the brake pipe.
BAIL12ABS141AVA 23
24. Remove the starter motor heat shield and earth.
BAIL12ABS142AVA 24
25. Remove the starter motor cover.
BAIL12ABS143AVA 25
47524342 29/05/2013
10.1 [10.001] / 13
19. Engine - Engine and crankcase
26. Disconnect the positive terminal (1) and bracket (2)
and position to one side.
BAIL12ABS144AVA 26
27. Disconnect the starter motor electrical connector.
BAIL12ABS148AVA 27
28. Disconnect the starter motor negative cables.
BAIL12ABS145AVA 28
29. Cut the radar harness cable ties.
BAIL12ABS146AVA 29
47524342 29/05/2013
10.1 [10.001] / 14
20. Engine - Engine and crankcase
30. Disconnect the battery isolator switch electrical con-
nector.
BAIL12ABS147AVA 30
31. Disconnect the front hitch pipes (1) and remove the
bracket (2).
BAIL12ABS149AVA 31
32. Remove the front hitch pipes.
BAIL12ABS151AVA 32
33. Detach the fuse/step bracket.
BAIL12ABS150AVA 33
47524342 29/05/2013
10.1 [10.001] / 15
21. Engine - Engine and crankcase
34. Disconnect the oil cooler quick release couplers.
For further information, refer to Oil cooler lines -
Service instruction (35.300).
BAIL12ABS152AVA 34
35. Disconnect the oil cooler quick release couplers (1),
remove the pipe bracket (2) and remove the oil cooler
pipes.
For further information, refer to Oil cooler lines -
Service instruction (35.300).
BAIL12ABS153AVA 35
36. Disconnect the green fuel line.
BAIL12ABS155AVA 36
37. Cut the cable ties.
BAIL12ABS156AVA 37
47524342 29/05/2013
10.1 [10.001] / 16
22. Engine - Engine and crankcase
38. Disconnect the diff lock supply pipe (1).
Remove the pipe retaining bracket (2) and remove
the diff lock pipe.
BAIL12ABS154AVA 38
Vehicles with ABS
39. Detach the wiring harness (1) and disconnect the
ABS speed sensor (2).
BAIL12ABS158AVA 39
Vehicles with standard front axle
40. Remove the front wheel drive shaft guard and drive
shaft.
BSD1959A 40
47524342 29/05/2013
10.1 [10.001] / 17
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Engine - Engine and crankcase
41. Cut the cable ties and detach the wiring.
BAIL12ABS157AVA 41
42. Remove the drive shaft flange.
BAIL11CCM137AVA 42
Vehicles with SuperSteer™ front axle
43. Remove the four-wheel drive shaft guard retaining
bolts.
NOTE: Repeat the operation on both sides of the
vehicle.
BAIS06CCM033AVA 43
44. Remove the four-wheel drive shaft guard.
45. Remove the four-wheel drive shaft front retaining
bolts.
NOTE: Support the four-wheel drive shaft.
BAIS06CCM034AVA 44
47524342 29/05/2013
10.1 [10.001] / 18
25. Engine - Engine and crankcase
46. Remove the four-wheel drive shaft.
BAIS06CCM035AVB 45
47. Using the tractor splitting equipment 380040228 In-
stall the larger wheeled part of the splitting equipment
under the front weight carrier.
BAIL12APH159AVA 46
48. Position the static part of the splitting equipment un-
der the transmission and secure to the transmission.
Install the smaller wheeled part of the splitting equip-
ment under the engine.
BAIL12APH160AVA 47
49. Connect the two pieces of the wheeled splitting gear
together with the alignment bar.
BAIL12APH161AVA 48
47524342 29/05/2013
10.1 [10.001] / 19
26. Engine - Engine and crankcase
50. Support the rear of the vehicle.
BAIL07APH145AVA 49
51. Remove the left-hand side engine to transmission
securing bolts.
NOTE: Repeat this step for the right-hand side.
BAIL07APH146BVA 50
52. Remove the centre engine to transmission securing
bolt (2). Remove the top left-hand engine to trans-
mission securing bolt (1).
NOTE: Repeat this step for the right-hand side.
BAIL07APH147AVA 51
47524342 29/05/2013
10.1 [10.001] / 20