This document provides instructions for removing and installing the engine and radiator on a 721E wheel loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an engine lift to remove the engine from the loader. Engine installation is the reverse of removal. Radiator removal requires draining the coolant and removing mounting bolts, hoses and electrical connections. Radiator installation is the reverse of removal.
Este documento presenta el diseño de una zapata aislada centrada para soportar una columna de 30 cm de ancho y 50 cm de largo. Proporciona los datos geométricos, de cargas y materiales requeridos para el diseño. Luego describe el proceso de diseño, incluyendo el cálculo de la capacidad portante neta del terreno, las dimensiones de la zapata, los esfuerzos transmitidos y últimos, y la verificación de la altura de la zapata por rigidez y corte.
El documento describe el proceso de estructuración y predimensionamiento de un edificio. Se estructuró el edificio con losas macizas, vigas peraltadas y chatas, columnas, y muros estructurales. Los elementos se predimensionaron considerando criterios como el peralte en función de la luz, el área en función de la carga y resistencia al concreto, y la longitud de muros necesaria en función de la fuerza basal y resistencia al corte. El documento proporciona detalles sobre cada etapa del predimensionamiento estructural.
Costos y presupuestos en construccion presentacion 1 okmigueljaimeparra
Este documento presenta los conceptos básicos de costos y presupuestos en construcción. Explica que un costo aplicado a una cantidad constituye un presupuesto. Detalla los componentes de los costos directos e indirectos y los parámetros utilizados para calcular los costos de mano de obra, materiales y equipos.
Este documento presenta el análisis de costos unitarios de tres partidas de obras:
1) Concreto FC=210 kg/cm2 en pavimento, con un rendimiento de 11.82 m3/día.
2) Pintura lineal en sardinel, con un rendimiento de 68.57 m/día.
3) Relleno de juntas con asfalto, con un rendimiento de 32 m/día.
Se incluyen cálculos de materiales, mano de obra, equipos y costos unitarios, así como comparaciones con datos bibli
The document discusses the historical background and advantages of the strength design method for reinforced concrete structures. It provides details on how structural safety is assured through factored loads and reduced material strengths. Key aspects of the strength design method covered include derivation of expressions for beam design, minimum and balanced steel ratios, requirements for under-reinforced and over-reinforced beams, and minimum thickness and deflection requirements.
Crown pth50 series hand pallet truck service repair manualfjskekazswdmme
This document is a service and parts manual for the PTH50 series pallet truck. It provides instructions for maintenance, troubleshooting, and replacing parts. The manual describes the hydraulic unit functions for raising, lowering and neutral operations. It also provides details on inspecting and lubricating components, checking fluid levels, and removing and disassembling the hydraulic unit.
The document discusses Centerline butterfly valves series VIA/RS. It provides details on:
- The valves' areas of application and product features such as corrosion resistance and permanently tight closure.
- Over 70,000 valves have been installed worldwide in power generation and other industrial sites.
- Technical specifications including size range, pressure ratings, temperature range and material options.
- Main applications in industries like paper, sugar, power plants, chemicals and more.
Este documento presenta el diseño de una zapata aislada centrada para soportar una columna de 30 cm de ancho y 50 cm de largo. Proporciona los datos geométricos, de cargas y materiales requeridos para el diseño. Luego describe el proceso de diseño, incluyendo el cálculo de la capacidad portante neta del terreno, las dimensiones de la zapata, los esfuerzos transmitidos y últimos, y la verificación de la altura de la zapata por rigidez y corte.
El documento describe el proceso de estructuración y predimensionamiento de un edificio. Se estructuró el edificio con losas macizas, vigas peraltadas y chatas, columnas, y muros estructurales. Los elementos se predimensionaron considerando criterios como el peralte en función de la luz, el área en función de la carga y resistencia al concreto, y la longitud de muros necesaria en función de la fuerza basal y resistencia al corte. El documento proporciona detalles sobre cada etapa del predimensionamiento estructural.
Costos y presupuestos en construccion presentacion 1 okmigueljaimeparra
Este documento presenta los conceptos básicos de costos y presupuestos en construcción. Explica que un costo aplicado a una cantidad constituye un presupuesto. Detalla los componentes de los costos directos e indirectos y los parámetros utilizados para calcular los costos de mano de obra, materiales y equipos.
Este documento presenta el análisis de costos unitarios de tres partidas de obras:
1) Concreto FC=210 kg/cm2 en pavimento, con un rendimiento de 11.82 m3/día.
2) Pintura lineal en sardinel, con un rendimiento de 68.57 m/día.
3) Relleno de juntas con asfalto, con un rendimiento de 32 m/día.
Se incluyen cálculos de materiales, mano de obra, equipos y costos unitarios, así como comparaciones con datos bibli
The document discusses the historical background and advantages of the strength design method for reinforced concrete structures. It provides details on how structural safety is assured through factored loads and reduced material strengths. Key aspects of the strength design method covered include derivation of expressions for beam design, minimum and balanced steel ratios, requirements for under-reinforced and over-reinforced beams, and minimum thickness and deflection requirements.
Crown pth50 series hand pallet truck service repair manualfjskekazswdmme
This document is a service and parts manual for the PTH50 series pallet truck. It provides instructions for maintenance, troubleshooting, and replacing parts. The manual describes the hydraulic unit functions for raising, lowering and neutral operations. It also provides details on inspecting and lubricating components, checking fluid levels, and removing and disassembling the hydraulic unit.
The document discusses Centerline butterfly valves series VIA/RS. It provides details on:
- The valves' areas of application and product features such as corrosion resistance and permanently tight closure.
- Over 70,000 valves have been installed worldwide in power generation and other industrial sites.
- Technical specifications including size range, pressure ratings, temperature range and material options.
- Main applications in industries like paper, sugar, power plants, chemicals and more.
El documento presenta una tabla con 19 cuadros que describen los costos unitarios de diversas partidas de obra civil como excavación, relleno, transporte de materiales, entre otros. Cada cuadro detalla los costos de mano de obra, materiales, equipos y rendimientos estándar por unidad de obra como m3 o km. El propósito es realizar un análisis de costos unitarios para obras civiles.
Este documento presenta un presupuesto para la ampliación y mejoramiento del sistema de agua potable y alcantarillado sanitario en la localidad de Chuquibamba, Perú. Incluye partidas para obras provisionales como campamento, almacén y baños portátiles, así como partidas para la línea de agua potable que involucran excavaciones, limpieza de terreno, trazo y replanteo.
Este presupuesto detalla los costos de la estructura metálica para un almacén. Incluye obras preliminares, provisionales y mecánicas como la fabricación e instalación de la cobertura, cerramiento lateral y portón, así como pinturas. El costo directo total es de 867,967.77 nuevos soles.
Este documento presenta un presupuesto para la construcción de una caja en Puerto Maldonado, Madre de Dios. Incluye los costos de las estructuras, obras preliminares, movimiento de tierras, concreto, arquitectura, carpintería, cerrajería y otros elementos. El presupuesto contiene más de 100 partidas con códigos, descripciones de los trabajos, unidades de medida y costos unitarios.
Este documento establece las normas para el régimen de fórmulas polinómicas de reajuste automático de precios en contratos de obras públicas en Perú. Describe la forma general básica de las fórmulas polinómicas, los índices de precios utilizados y el proceso de cálculo de reajustes. También especifica normas para obras atrasadas, adelantadas y con adelantos específicos para materiales.
Este documento proporciona especificaciones técnicas para diferentes tipos de postes de concreto utilizados como soporte para luminarias en redes de alumbrado público. Describe las dimensiones, resistencias, cargas de prueba y procesos de fabricación para postes rectos cortos y largos, así como postes parabólicos. Incluye tablas con esta información para cada tipo de poste junto con su peso aproximado.
http://www.revitalizate.mx +52 (998) 2248450
MBrace Sistema de Compuesto de Refuerzo, es un sistema de refuerzo FPR (polímero reforzado con fibras) de adhesión externa que ha sido desarrollado para reforzar estructuras de concreto y mampostería ya existentes. La tecnología del sistema, comprobada en campo, consiste de láminas secas de alto desempeño construidas con fibras de carbono grado aeroespacial, fibras de aramida y fibras de vidrio tipo «E» más resinas poliméricas formuladas específicamente para el Sistema MBrace.
Estas resinas poliméricas incluyen un imprimante para la superficie y una pasta de relleno para asegurar la adhesión adecuada del sistema y resinas saturantes para la impregnación de las fibras y así formar una lámina FRP de alto desempeño.
Este documento presenta un análisis de precios unitarios para diversos elementos de instalaciones sanitarias como lavabos, lavaderos y sus accesorios. Se detallan 9 partidas con sus códigos, descripciones, materiales requeridos, costos unitarios directos y cantidades. El documento proporciona información técnica y presupuestaria sobre estos elementos para mejorar los servicios de salud de un hospital en la región de Tacna, Perú.
Este documento presenta un manual para la construcción con acero galvanizado liviano. Incluye información sobre herramientas de seguridad, componentes del sistema, métodos de anclaje, trazado, construcción de muros, tabiques, vanos, diagonales, cerchas, techos, pisos y otros usos. También contiene tablas con especificaciones técnicas de los productos. El objetivo es servir de guía para nuevos usuarios de este sistema constructivo.
Este documento presenta un estudio sobre los criterios de diseño y cálculo de encofrados de elementos verticales y su aplicación al diseño de varias estructuras. Introduce los factores técnicos, económicos y estéticos a considerar en la elección de un encofrado, como la geometría de la obra, características del hormigón, costes y plazos. A continuación, analiza aspectos como la presión del hormigón, tipos de encofrados, cálculo de elementos y sistemas de trepa para muros altos
This document provides an overview and reference for the SAP2000 structural analysis software. It describes SAP2000's capabilities for finite element analysis and design of structures. SAP2000 is a proprietary software developed by Computers and Structures, Inc. for analyzing and designing structures. The document covers topics such as modeling elements like frames and shells, defining properties, applying loads, performing static and dynamic analysis, and interpreting results. It is intended to help users understand the assumptions and proper use of the software.
New holland w130 c tier 4 wheel loader service repair manualfjkskmmdmme
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for relevant fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdffusedkdd9idi
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdfcheng576587ce
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for relevant fasteners.
New holland w130 c tier 4 wheel loader service repair manual instant downloadudfjsjjekkekmem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for reinstalling components.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdffujksekd9dokd
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for correct reinstallation of components.
New holland w130 c tier 4 wheel loader service repair manualfujsjefkskem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for correct reinstallation of components.
New holland w130 c tier 4 wheel loader service repair manualujfjjkskkmdme
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdfhmc151121
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New holland w130 c tier 4 wheel loader service repair manualuufdjjjskkemm
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The procedures include disconnecting battery ground cables, draining coolant and fuel, removing mounting bolts and hoses, and lifting the engine from the vehicle. Reinstallation involves lowering the engine back into position and reconnecting all hoses, brackets, and electrical components. Proper torque specifications are provided for all fasteners.
New holland w130 c tier 4 wheel loader service repair manualfikskefjsekfsem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The procedures include draining fluids, disconnecting linkages, removing mounting hardware, and installing in the reverse order. Specifications and torque values are provided for reinstalling components.
El documento presenta una tabla con 19 cuadros que describen los costos unitarios de diversas partidas de obra civil como excavación, relleno, transporte de materiales, entre otros. Cada cuadro detalla los costos de mano de obra, materiales, equipos y rendimientos estándar por unidad de obra como m3 o km. El propósito es realizar un análisis de costos unitarios para obras civiles.
Este documento presenta un presupuesto para la ampliación y mejoramiento del sistema de agua potable y alcantarillado sanitario en la localidad de Chuquibamba, Perú. Incluye partidas para obras provisionales como campamento, almacén y baños portátiles, así como partidas para la línea de agua potable que involucran excavaciones, limpieza de terreno, trazo y replanteo.
Este presupuesto detalla los costos de la estructura metálica para un almacén. Incluye obras preliminares, provisionales y mecánicas como la fabricación e instalación de la cobertura, cerramiento lateral y portón, así como pinturas. El costo directo total es de 867,967.77 nuevos soles.
Este documento presenta un presupuesto para la construcción de una caja en Puerto Maldonado, Madre de Dios. Incluye los costos de las estructuras, obras preliminares, movimiento de tierras, concreto, arquitectura, carpintería, cerrajería y otros elementos. El presupuesto contiene más de 100 partidas con códigos, descripciones de los trabajos, unidades de medida y costos unitarios.
Este documento establece las normas para el régimen de fórmulas polinómicas de reajuste automático de precios en contratos de obras públicas en Perú. Describe la forma general básica de las fórmulas polinómicas, los índices de precios utilizados y el proceso de cálculo de reajustes. También especifica normas para obras atrasadas, adelantadas y con adelantos específicos para materiales.
Este documento proporciona especificaciones técnicas para diferentes tipos de postes de concreto utilizados como soporte para luminarias en redes de alumbrado público. Describe las dimensiones, resistencias, cargas de prueba y procesos de fabricación para postes rectos cortos y largos, así como postes parabólicos. Incluye tablas con esta información para cada tipo de poste junto con su peso aproximado.
http://www.revitalizate.mx +52 (998) 2248450
MBrace Sistema de Compuesto de Refuerzo, es un sistema de refuerzo FPR (polímero reforzado con fibras) de adhesión externa que ha sido desarrollado para reforzar estructuras de concreto y mampostería ya existentes. La tecnología del sistema, comprobada en campo, consiste de láminas secas de alto desempeño construidas con fibras de carbono grado aeroespacial, fibras de aramida y fibras de vidrio tipo «E» más resinas poliméricas formuladas específicamente para el Sistema MBrace.
Estas resinas poliméricas incluyen un imprimante para la superficie y una pasta de relleno para asegurar la adhesión adecuada del sistema y resinas saturantes para la impregnación de las fibras y así formar una lámina FRP de alto desempeño.
Este documento presenta un análisis de precios unitarios para diversos elementos de instalaciones sanitarias como lavabos, lavaderos y sus accesorios. Se detallan 9 partidas con sus códigos, descripciones, materiales requeridos, costos unitarios directos y cantidades. El documento proporciona información técnica y presupuestaria sobre estos elementos para mejorar los servicios de salud de un hospital en la región de Tacna, Perú.
Este documento presenta un manual para la construcción con acero galvanizado liviano. Incluye información sobre herramientas de seguridad, componentes del sistema, métodos de anclaje, trazado, construcción de muros, tabiques, vanos, diagonales, cerchas, techos, pisos y otros usos. También contiene tablas con especificaciones técnicas de los productos. El objetivo es servir de guía para nuevos usuarios de este sistema constructivo.
Este documento presenta un estudio sobre los criterios de diseño y cálculo de encofrados de elementos verticales y su aplicación al diseño de varias estructuras. Introduce los factores técnicos, económicos y estéticos a considerar en la elección de un encofrado, como la geometría de la obra, características del hormigón, costes y plazos. A continuación, analiza aspectos como la presión del hormigón, tipos de encofrados, cálculo de elementos y sistemas de trepa para muros altos
This document provides an overview and reference for the SAP2000 structural analysis software. It describes SAP2000's capabilities for finite element analysis and design of structures. SAP2000 is a proprietary software developed by Computers and Structures, Inc. for analyzing and designing structures. The document covers topics such as modeling elements like frames and shells, defining properties, applying loads, performing static and dynamic analysis, and interpreting results. It is intended to help users understand the assumptions and proper use of the software.
New holland w130 c tier 4 wheel loader service repair manualfjkskmmdmme
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for relevant fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdffusedkdd9idi
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdfcheng576587ce
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for relevant fasteners.
New holland w130 c tier 4 wheel loader service repair manual instant downloadudfjsjjekkekmem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing accessories, and using an engine lifting fixture to remove the engine from the vehicle. Installation is largely the reverse of removal. Procedures for radiator removal include draining coolant and removing mounting brackets, and installation is the reverse of removal. Torque specifications are provided for reinstalling components.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdffujksekd9dokd
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for correct reinstallation of components.
New holland w130 c tier 4 wheel loader service repair manualfujsjefkskem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for correct reinstallation of components.
New holland w130 c tier 4 wheel loader service repair manualujfjjkskkmdme
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdfhmc151121
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New holland w130 c tier 4 wheel loader service repair manualuufdjjjskkemm
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The procedures include disconnecting battery ground cables, draining coolant and fuel, removing mounting bolts and hoses, and lifting the engine from the vehicle. Reinstallation involves lowering the engine back into position and reconnecting all hoses, brackets, and electrical components. Proper torque specifications are provided for all fasteners.
New holland w130 c tier 4 wheel loader service repair manualfikskefjsekfsem
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The procedures include draining fluids, disconnecting linkages, removing mounting hardware, and installing in the reverse order. Specifications and torque values are provided for reinstalling components.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdffusjekkdkdme3
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for all fasteners.
New holland w130 c tier 4 wheel loader service repair manualfjsjekdmmeme
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, then removing mounting bolts. Installation is also reverse of removal. Torque specifications are provided for correct reinstallation of components.
New Holland W170C Wheel Loader Service Repair Manual.pdfgan51huishu
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and refills the cooling system.
New Holland W170C Wheel Loader Service Repair Manual.pdffusedkdd9idi
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and lifting the engine out. Installation is the reverse of removal. Radiator removal involves draining coolant and removing mounting hardware, while installation reverses this process.
New holland w170 c wheel loader service repair manualfusjfskeekemm
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and mounts the radiator back in place.
New Holland W170C Wheel Loader Service Repair Manual.pdffujksekd9dokd
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation follows the reverse steps.
New holland w170 c wheel loader service repair manualfujsjefjkskefksem
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and lifting the engine out. Installation is the reverse of removal. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and mounts the radiator.
New Holland W170C Wheel Loader Service Repair Manual.pdfhmc151121
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and refills the cooling system.
New holland w170 c wheel loader service repair manualufjjdkksmeme
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and mounts the radiator back in place.
Similar to Case 721 e eu wheel loader service repair manual (20)
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualfujsefxdeksemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and side counterweights. The counterweight is removed using an eyebolt and lifting device. Fenders are removed using eyebolts through mount holes and lifted away. The hood assembly can be pivoted or completely removed using a lifting device attached to the spine. The hydraulic tank is removed by disconnecting hoses, removing mounting hardware, and lifting it away while supported.
Hyster c008 (h370 c) forklift service repair manualfujsefxdeksemm
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from outlet oil.
Hyster b187 (s50 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Hyster b187 (s40 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...fujsefxdeksemm
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...fujsefxdeksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...fujsefxdeksemm
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It outlines the required tools and safety precautions, and gives step-by-step instructions to release pressure, remove hoses and bolts, and disassemble internal components like springs and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...fujsefxdeksemm
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...fujsefxdeksemm
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...fujsefxdeksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. It describes:
1) Removing the fuel injection lines, oil supply/drain lines, heat shield, and other components to access the pump housing.
2) Using various tools like bolts, washers, and pullers to remove the pump housing mounting bolts, nuts, and center bolt to detach the housing.
3) Lifting the housing off the engine using a sling and removing O-rings from the housing and governor.
4) Reversing the removal process to reinstall the housing, ensuring proper alignment and torque of mounting hardware.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)fujsefxdeksemm
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and gives step-by-step instructions to remove components like the rear housing, pinion drive, shift lever, brushes, and field winding coil. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualfujsefxdeksemm
This document provides instructions for disassembling and assembling starting motors for Caterpillar excavators. It describes the process for three starting motor models: 37-MT, 41-MT and 42-MT. The disassembly process involves removing components like the solenoid, rear housing, pinion drive housing, shift lever housing and field winding coil. The assembly process describes installing these components in reverse order while applying lubricants to bushings and torquing screws correctly.
The document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly that remove parts like the fuel ratio control, housing, springs, pins, seals, and more. It then lists 33 steps for assembly that install these parts in reverse order, noting to clean parts and apply oil before assembling. Tools like retaining ring pliers and drivers are required for some steps. Precise alignment and positioning of parts is emphasized during assembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for disassembling the piston motor of a 216B3 Skid Steer Loader. It outlines 25 steps to remove components such as nuts, valves, springs, pistons, seals, bearings, gears and more. Precautions are included to release spring forces safely. Required tools include retaining ring pliers, drivers, pullers and presses. Detailed illustrations accompany each step for clarity.
Case ih stx 380 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine systems, air induction systems, electrical systems, steering systems, and removal/installation of engines. It also lists recommended engine service manuals for different engine models used in the tractors.
Case ih steiger 535 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih steiger 430 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih puma 220 tier 4 b (final) tractor service repair manualfujsefxdeksemm
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
7. 1001-3
87551874A Revised 1-07 Printed in E.C.
TORQUE SPECIFICATIONS - DECIMAL HARDWARE
Use the torques in this chart when special torques
are not given. These torques apply to fasteners with
both UNC and UNF threads as received from
suppliers dry, or when lubricated with engine oil. Not
applicable if special graphities, Molydisulfide
greases, or other extreme pressure lubricants are
used.
Grade 5 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
1/4 inch 108 to 132 12 to 15
5/16 inch 204 to 252 23 to 28
3/8 inch 420 to 504 48 to 57
Size
Pound-
Feet
Newton
metres
7/16 inch 54 to 64 73 to 87
1/2 inch 80 to 96 109 to 130
9/16 inch 110 to 132 149 to 179
5/8 inch 150 to 180 203 to 244
3/4 inch 270 to 324 366 to 439
7/8 inch 400 to 480 542 to 651
1.0 inch 580 to 696 787 to 944
1-1/8 inch 800 to 880 1085 to 1193
1-1/4 inch 1120 to 1240 1519 to 1681
1-3/8 inch 1460 to 1680 1980 to 2278
1-1/2 inch 1940 to 2200 2631 to 2983
Grade 8 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
1/4 inch 144 to 180 16 to 20
5/16 inch 288 to 348 33 to 39
3/8 inch 540 to 648 61 to 73
Size
Pound-
Feet
Newton
metres
7/16 inch 70 to 84 95 to 114
1/2 inch 110 to 132 149 to 179
9/16 inch 160 to 192 217 to 260
5/8 inch 220 to 264 298 to 358
3/4 inch 380 to 456 515 to 618
7/8 inch 600 to 720 814 to 976
1.0 inch 900 to 1080 1220 to 1465
1-1/8 inch 1280 to 1440 1736 to 1953
1-1/4 inch 1820 to 2000 2468 to 2712
1-3/8 inch 2380 to 2720 3227 to 3688
1-1/2 inch 3160 to 3560 4285 to 4827
NOTE: Use thick nuts with Grade 8 bolts.
8. 1001-4
87551874A Revised 1-07 Printed in E.C.
TORQUE SPECIFICATIONS - METRIC HARDWARE
Use the following torques when specifications are not
given.
These values apply to fasteners with coarse threads
as received from supplier, plated or unplated, or
when lubricated with engine oil. These values do not
apply if graphite or Molydisulfide grease or oil is
used.
Grade 12.9 Bolts, Nuts, and Studs
Usually the torque values specified for grade 10.9
fasteners can be used satisfactorily on grade 12.9
fasteners.
Grade 8.8 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
M4 24 to 36 3 to 4
M5 60 to 72 7 to 8
M6 96 to 108 11 to 12
M8 228 to 276 26 to 31
M10 456 to 540 52 to 61
Size
Pound-
Feet
Newton
metres
M12 66 to 79 90 to 107
M14 106 to 127 144 to 172
M16 160 to 200 217 to 271
M20 320 to 380 434 to 515
M24 500 to 600 675 to 815
M30 920 to 1100 1250 to 1500
M36 1600 to 1950 2175 to 2600
8.8
Grade 10.9 Bolts, Nuts, and Studs
Size
Pound-
Inches
Newton
metres
M4 36 to 48 4 to 5
M5 84 to 96 9 to 11
M6 132 to 156 15 to 18
M8 324 to 384 37 to 43
Size
Pound-
Feet
Newton
metres
M10 54 to 64 73 to 87
M12 93 to 112 125 to 150
M14 149 to 179 200 to 245
M16 230 to 280 310 to 380
M20 450 to 540 610 to 730
M24 780 to 940 1050 to 1275
M30 1470 to 1770 2000 to 2400
M36 2580 to 3090 3500 to 4200
10.9
12.9
9. 1001-5
87551874A Revised 1-07 Printed in E.C.
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS
37 Degree Flare Fitting
Tube OD
Hose ID
Thread
Size
Pound-
Inches
Newton
metres
1/4 inch
6.4 mm
7/16-20 72 to 144 8 to 16
5/16 inch
7.9 mm
1/2-20 96 to 192 11 to 22
3/8 inch
9.5 mm
9/16-18 120 to 300 14 to 34
1/2 inch
12.7 mm
3/4-16 180 to 504 20 to 57
5/8 inch
15.9 mm
7/8-14 300 to 696 34 to 79
Tube OD
Hose ID
Thread
Size
Pound-
Feet
Newton
metres
3/4 inch
19.0 mm
1-1/16-12 40 to 80 54 to 108
7/8 inch
22.2 mm
1-3/16-12 60 to 100 81 to 135
1.0 inch
25.4 mm
1-5/16-12 75 to 117 102 to 158
1-1/4 inch
31.8 mm
1-5/8-12 125 to 165 169 to 223
1-1/2 inch
38.1 mm
1-7/8-12 210 to 250 285 to 338
Split Flange Mounting Bolts
Size
Pound-
Inches
Newton
metres
5/16-18 180 to 240 20 to 27
3/8-16 240 to 300 27 to 34
7/16-14 420 to 540 47 to 61
Size
Pound-
Feet
Newton
metres
1/2-13 55 to 65 74 to 88
5/8-11 140 to 150 190 to 203
Straight Threads with O-ring
Tube OD
Hose ID
Thread
Size
Pound-
Inches
Newton
metres
1/4 inch
6.4 mm
7/16-20 144 to 228 16 to 26
5/16 inch
7.9 mm
1/2-20 192 to 300 22 to 34
3/8 inch
9.5 mm
9/16-18 300 to 480 34 to 54
1/2 inch
12.7 mm
3/4-16 540 to 804 57 to 91
Tube OD
Hose ID
Thread
Size
Pound-
Feet
Newton
metres
5/8 inch
15.9 mm
7/8-14 58 to 92 79 to 124
3/4 inch
19.0 mm
1-1/16-12 80 to 128 108 to 174
7/8 inch
22.2 mm
1-3/16-12 100 to 160 136 to 216
1.0 inch
25.4 mm
1-5/16-12 117 to 187 159 to 253
1-1/4 inch
31.8 mm
1-5/8-12 165 to 264 224 to 357
1-1/2 inch
38.1 mm
1-7/8-12 250 to 400 339 to 542
12. 2000-3
87551874A Issued 1-07 Printed in E.C.
ENGINE
Removal
STEP 1
BD03A040
Park machine on a level surface and lower bucket to
ground. Put articulation lock in LOCKED position.
STEP 2
Stop engine. Actuate brake pedal several times to
discharge brake accumulators. Put key switch in ON
position and move loader control lever back and forth
at least 30 times to release any pressure from
hydraulic circuit. Put key switch in OFF position.
STEP 3
Slowly loosen the filler cap for hydraulic reservoir to
release air pressure in hydraulic reservoir.
STEP 4
BD06F108
The master and hood raise switch are located in the
right batter box. Raise the hood with the hood lift
motor. Put master disconnect switch in OFF position.
Remove both battery covers and disconnect
batteries from the machine.
STEP 5
BD02N160
Put a 37 liter (10 gallon) container below radiator
drain. Remove radiator cap. Remove cap and drain
coolant into container. Install cap after coolant has
drained. Install radiator cap.
STEP 6
BD02N160
Put a 14.2 liter (15 U.S. quarts) container below
engine oil drain. Remove cap and drain oil into
container. Install cap after oil has drained.
NOTE: After draining oil disconnect drain hose from
frame for removal with engine.
13. 2000-4
87551874A Issued 1-07 Printed in E.C.
STEP 7
BD03A231
Double up a nylon lifting strap (1) and slide through
the exhaust stack (2) on the hood.
STEP 8
BD03A230
Place a solid steel bar through the strap, raise the
hood and release tension on the lifting motor.
STEP 9
BD03A228
Remove the pin from the top of the lifting motor.
STEP 10
BD06F109
Tag and disconnect hood wiring harness connector
from rear chassis wiring harness connector.
STEP 11
BD03A227
BD03A226
Remove mount bolt (1) and backup alarm wiring
harness clamp from cooler housing. Have another
person balance the hood and remove the hood hinge
mounting bolts (2) from the cooler frame.
1
2
1
2
2
14. 2000-5
87551874A Issued 1-07 Printed in E.C.
STEP 12
BD03A232
Carefully raise and remove hood from loader. Lower
hood onto suitable platform and disconnect lifting
equipment.
STEP 13
BD03A224
Tag and disconnect engine wiring harness connector
from air filter restriction switch.
STEP 14
BD03A225
Loosen clamp on air cleaner intake hose and remove
the crankcase ventilation hose.
STEP 15
BD06F110
Loosen clamps on turbocharger and air cleaner,
remove the intake hose.
STEP 16
BD06F110
Loosen the clamp on the turbocharger for the after
cooler inlet hose.
STEP 17
BD03A115
Loosen the clamp on the after cooler and remove the
after cooler inlet hose from the machine.
15. 2000-6
87551874A Issued 1-07 Printed in E.C.
STEP 18
BD06F111
Loosen the clamp on the intake manifold for the after
cooler output hose.
STEP 19
BD03A118
Loosen the clamp on the after cooler and remove the
after cooler outlet hose from the machine.
STEP 20
BD06F110
Loosen the exhaust clamp from the turbocharger.
STEP 21
BD06F112
Remove the air cleaner and muffler from the bracket.
STEP 22
BD06F113
BD06F114
Remove the four mounting bolts from the belt cover,
remove the cover.
NOTE: After removing the belt cover remove the cover
mounting brackets from the machine frame.
16. 2000-7
87551874A Issued 1-07 Printed in E.C.
STEP 23
BD06F115
Remove the drive belt from the engine.
STEP 24
BD06F116
Loosen clamps and remove lower cooler hose from
the engine.
STEP 25
BD06F117
If loader is equipped with air conditioning, identify,
tag, and disconnect the engine wiring harness
connectors from air compressor clutch connector (1).
Remove the three mounting bolts (2) for the
compressor and set the compressor on the left
battery cover.
STEP 26
BD06F118
Tag and disconnect the wiring from the alternator.
STEP 27
BD06F119
Remove bolt securing wiring harness clamp to
engine.
STEP 28
BD06F120
Remove bolt securing wiring harness clamp (1) to the
engine. Remove ground wires (2) from the engine.
1
2
1
2
17. 2000-8
87551874A Issued 1-07 Printed in E.C.
STEP 29
BD06F121
Tag and remove the wires from the starter solenoid
(3), remove the ground cable (2), and ground strap
(1) from the starter.
NOTE: Move the starter cables away from the engine,
move the wiring harness away from the engine.
STEP 30
BD06F146
Disconnect the engine coolant vent hose and root to
the rear of the engine.
STEP 31
BD06F122
Remove the radiator hose (1) from the rear of the
engine, remove the heater hose from the rear of the
engine (2), remove the clamp bolts and clamps (3)
from the bell housing.
STEP 32
BD06F111
Tag and remove the grid heater cable.
STEP 33
BD03A142
Disconnect the wiring harness from the EDC 7
controller.
NOTE: Lifting up on the lever will release the connector
from the controller.
STEP 34
BD06F123
Remove the fuel line from the top of the EDC 7
controller, plug the line and cap the fitting.
3
1
2
2
1
3
18. 2000-9
87551874A Issued 1-07 Printed in E.C.
STEP 35
BD06F124
Tag and disconnect the fuel filter heater wires (1),
disconnect the fuel line (2) from the fuel filter head,
plug the line and cap the fitting.
STEP 36
BD06F125
Remove bolt and clamp.
STEP 37
BD06F126
Connect and turn on vacuum pump to hydraulic
reservoir. Tag and remove the hydraulic lines from
the brake system pump, plug the lines and cap the
fittings.
STEP 38
BD06F127
Remove the lower cover for the drive shaft.
STEP 39
BD03A172
Remove the drive shaft bolts from the flywheel. Move
the drive shaft clear of the flywheel.
STEP 40
Connect suitable lifting equipment to engine lifting
brackets. Take up all slack in lifting equipment.
Remove the engine mounting bolts and lift the engine
enough to gain access to the drain hose, pull the
drain hose with the engine.
STEP 41
Slowly raise engine from rear chassis. Be sure all
harness connections and hoses have been
disconnected and are clear of the engine. Remove
engine from machine.
1
2
19. 2000-10
87551874A Issued 1-07 Printed in E.C.
Installation
BS03B035
STEP 42
If engine rubber isolators require replacement,
remove and discard isolators (3 and 4). Install new
rubber isolator (4), then rubber isolator (3).
STEP 43
Slowly raise engine and move into position over rear
chassis. Be sure all harness connections and hoses
are out of the way then lower engine. Put washer (5)
between front rubber isolator (4) and chassis. Install
washer (2), bolt (1), washer (6), and nut (7) in engine
isolators. Lower engine into position.
STEP 44
Tighten engine mounting bolts to a torque of 244 to
298 Nm (180 to 220 lb-ft).
STEP 45
Disconnect lifting equipment from engine lifting
brackets.
STEP 46
Connect engine oil drain hose to frame bracket.
STEP 47
BD03A172
At front of engine, position drive shaft on engine
coupling. Install six bolts to secure drive shaft to
engine coupling. Tighten the six bolts to a torque of
53 to 62 Nm (39 to 46 lb-ft).
1. ENGINE MOUNT BOLT 3. INSOLATOR UPPER 5. WASHER 7. NUT
2. WASHER 4. INSOLATOR LOWER 6. WASHER 8. REMOTE OIL DRAIN HOSE
1
4
3
2
7
6
5
4
3
2
1
1
7
8
7
6
5
2
3
4
5
6
20. 2000-11
87551874A Issued 1-07 Printed in E.C.
STEP 48
BD06F127
Install the lower cover for the drive shaft.
STEP 49
BD06F126
Connect and turn on vacuum pump to the hydraulic
reservoir. Remove caps from fittings and plugs from
hoses. Connect hoses to brake pump following tags
installed during removal. Remove and discard tags.
Turn off and disconnect vacuum pump from hydraulic
reservoir.
STEP 50
BD06F125
Install bolt and clamp for fuel return hose.
STEP 51
BD06F124
Remove cap from fitting and plug from the hose,
connect fuel line (2). Connect fuel filter heater wires
(1). Remove and discard tag.
STEP 52
BD06F123
Remove cap from fitting and plug from the hose,
connect fuel line to EDC 7.
STEP 53
BD03A142
Connect wiring harness to EDC 7 controller.
NOTE: Start the connector on the EDC 7 with lever
straight out from EDC 7. Use lever to pull connector into
position.
1
2
21. 2000-12
87551874A Issued 1-07 Printed in E.C.
STEP 54
BD06F111
Connect grid heater cable to grid heater. Remove
and discard tag.
STEP 55
BD06F122
Install the heater hose (2) to the rear of the engine,
mount the clamps (3), install the radiator hose (1).
STEP 56
BD06F146
Connect the engine coolant vent hose.
STEP 57
BD06F121
Install the wires to the starter solenoid (3), install the
ground cable (2), and ground strap (1) to the starter.
Remove and discard tags.
STEP 58
BD06F120
Install bolt securing wiring harness (1) clamp to the
engine. Install ground wires (2) to the engine.
STEP 59
BD06F119
Install bolt securing wiring harness clamp to engine.
2
1
3
3
1
2
1
2
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 2000-13
87551874A Issued 1-07 Printed in E.C.
STEP 60
BD06F118
Connect the wiring to the alternator. Remove and
discard tags.
STEP 61
BD06F117
If loader is equipped with air conditioning, mount the
compressor using the three mounting bolts (2),
connect the engine wiring harness connectors to air
compressor clutch connector (1). Remove and
discard tags.
STEP 62
BD06F116
Install lower cooler hose to the engine and tighten
the clamps to a torque of 10.1 to 11.3 Nm (90 to 100
lb-inch).
STEP 63
BD06F115
Install the drive belt.
STEP 64
BD06F113
BD06F114
Install the cover mounting brackets to the machine
frame. Install the belt cover, install the four mounting
bolts for the belt cover.
1
2
24. 2000-14
87551874A Issued 1-07 Printed in E.C.
STEP 65
BD06F112
Place the muffler and air cleaner on the bracket.
Install mounting bolts in air cleaner and tighten,
install the mounting bolts in the muffler and leave
loose at this time.
STEP 66
BD06F110
Install and tighten the exhaust clamp on the
turbocharger, tighten the muffler mounting bolts.
STEP 67
BD03A118
Place the after cooler outlet hose on the machine.
Tighten the clamp on the after cooler.
STEP 68
BD06F111
Tighten the clamp on the intake manifold for the after
cooler output hose.
STEP 69
BD03A115
Place the after cooler inlet hose on the machine.
Tighten the clamp on the after cooler.
STEP 70
BD06F110
Tighten the clamp on the turbocharger for the after
cooler inlet hose.
25. 2000-15
87551874A Issued 1-07 Printed in E.C.
STEP 71
BD06F110
Install the intake hose and tighten the clamps on
turbocharger and air cleaner.
STEP 72
BD03A225
Install the crankcase ventilation hose and tighten the
clamp on air cleaner intake hose.
STEP 73
BD03A224
Connect engine wiring harness connector to air filter
restriction switch. Remove and discard tag.
STEP 74
BD03A232
Carefully raise and place hood over loader.
NOTE: Refer to step 7 and 8 of removal for lifting
procedure.
STEP 75
BD03A227
BD03A226
Have another person balance the hood, install the
hood hinge mounting bolts (2) to the cooler frame.
Install mount bolt (1) and backup alarm wiring
harness clamp to cooler housing.
1
2
2
26. 2000-16
87551874A Issued 1-07 Printed in E.C.
STEP 76
BD03A228
Install the pin from the top of the lifting motor, lower
and remove lifting equipment.
STEP 77
BD06F109
Connect hood wiring harness connector to rear
chassis wiring harness connector. Remove and
discard tag.
STEP 78
BD03A221
NOTE: If hood strut is not adjusted properly the hood will
be damaged.
When a hood is removed and replaced an initial
adjustment on the strut is necessary. Adjust between
the top of the lift motor adjusting jam nut (1) to the top
of the threads (2) to 20 mm (X). With the motor down
to its lowest point take a measurement between the
left hand side hood bumper and the counter weight,
record this measurement (Y). Use the following table
to adjust the strut (X).
Hood Adjustment Table
Y
(MM)
X
(MM)
Y
(MM)
X
(MM)
Y
(MM)
X
(MM)
Y
(MM)
X
(MM)
1 19 21 14 41 9 61 5
2 19 22 14 42 9 62 5
3 18 23 14 43 9 63 4
4 18 24 13 44 9 64 4
5 18 25 13 45 9 65 4
6 18 26 13 46 8 66 4
7 17 27 13 47 8 67 3
8 17 28 12 48 8 68 3
9 17 29 12 49 8 69 3
10 17 30 12 50 7 70 3
11 16 31 12 51 7 71 2
12 16 32 12 52 7 72 2
13 16 33 11 53 7 73 2
14 16 34 11 54 6 74 2
15 16 35 11 55 6 75 2
16 15 36 11 56 6 76 1
17 15 37 10 57 6 77 1
18 15 38 10 58 6 78 1
19 15 39 10 59 5 79 1
20 14 40 10 60 5 80 0
2
1
27. 2000-17
87551874A Issued 1-07 Printed in E.C.
STEP 79
BD02N160
Check and make sure that drain caps are tight.
STEP 80
Install a new oil filter on engine. Fill engine with 14.2
liters (15 quarts) of Case AKCELA No. 1 Engine Oil
(SAE 15W-40).
STEP 81
If hydraulic reservoir was drained, fill reservoir with
105.7 liters (27.9 gallons) of Case AKCELA Hy-Tran
Ultra® fluid.
STEP 82
Fill engine coolant system with a solution of 50%
Ethylene Glycol and 50% water. Cooling system
capacity is 36.9 liters (9.75 gallons). Install the
radiator cap. Fill the coolant reservoir up to the FULL
mark on the reservoir.
STEP 83
Connect the batteries, install battery covers, put
master disconnect switch in ON position.
STEP 84
Start engine and run the engine at low idle. Run the
engine at operating temperature for approximately
five minutes to completely mix the Ethylene Glycol
and water. When the coolant is at operating
temperature, stop the engine. When engine has
cooled, check the coolant level at the reservoir.
WARNING: Hot coolant can spray out if radiator cap is
removed. To remove radiator cap: Let system cool, turn to
first notch, then wait until all pressure is released. Scalding
can result from fast removal of radiator cap.
STEP 85
BD06F108
Lower the hood with the hood lift motor.
STEP 86
Put articulation lock in OPERATING position.
28. 2000-18
87551874A Issued 1-07 Printed in E.C.
RADIATOR
Removal
STEP 1
Park loader on level surface and lower bucket to
ground. Apply parking brake and shut down engine.
STEP 2
BD03A040
Put articulation lock in LOCKED position.
STEP 3
Put master disconnect switch in OFF position.
STEP 4
BD03A120
Have another person raise and hold the side panel
up into the raised position. Remove the two mounting
screws for the side panel, remove the panel.
NOTE: Photo is of the oil cooler side of the machine, the
procedure is the same.
STEP 5
BD06F128
Remove bolt and washer securing LH fender.
Remove LH fender.
STEP 6
BD02N160
Put a 37 liter (10 gallon) container below radiator
drain. Remove radiator cap then remove cap and
drain coolant into container. Install cap after coolant
has drained. Install radiator cap.
STEP 7
BD03A109
Release catch and tilt air conditioning condenser
core up to gain access to upper radiator hose.