This document is a service manual that provides maintenance and repair information for various tractor models in the T6 series, including the T6.125, T6.145, T6.155, T6.165, T6.175, T6.160 and T6.180. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulics and other components. It includes detailed content on maintenance, troubleshooting and repair procedures for the components of the listed tractor models.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdffujsekmd9dik
This document provides lubrication specifications and fluid capacities for various JCB machine models, including 525, 527, 530, 535 and 537 models. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases and other lubricants. It also provides coolant mixture recommendations and notes that new engines do not require a break-in period and should be used immediately in normal work cycles.
JCB 4DX Backhoe Loader Service Repair Manual.pdffujsekmd9dik
This service manual provides information on maintenance and repair of the 4DX Backhoe Loader. It includes sections on general information, routine maintenance, attachments, body and framework, electrics, controls, hydraulics, transmission, brakes, steering and engine. The manual provides information on identification plates, torque settings, greasing points, cleaning air filters, and replacing engine coolant. It also includes details on preservation for storing the machine when not in use for long periods.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdffujsekmd9dik
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
Clark GPX 40 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 50E Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdffujsekmd9dik
This document provides lubrication specifications and fluid capacities for various JCB machine models, including 525, 527, 530, 535 and 537 models. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases and other lubricants. It also provides coolant mixture recommendations and notes that new engines do not require a break-in period and should be used immediately in normal work cycles.
JCB 4DX Backhoe Loader Service Repair Manual.pdffujsekmd9dik
This service manual provides information on maintenance and repair of the 4DX Backhoe Loader. It includes sections on general information, routine maintenance, attachments, body and framework, electrics, controls, hydraulics, transmission, brakes, steering and engine. The manual provides information on identification plates, torque settings, greasing points, cleaning air filters, and replacing engine coolant. It also includes details on preservation for storing the machine when not in use for long periods.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdffujsekmd9dik
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
Clark GPX 40 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 50E Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 35 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
The document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support the heavy components. The removal process involves removing bolts, installing lifting brackets, and using hydraulic tools to separate the carrier from the final drive. Precautions are listed for containing fluids during disassembly.
The document provides instructions for removing and installing the front axle of a M314F wheeled excavator. It details:
1) Removing the front axle assembly from the machine and disassembling it by removing components like the differential, bearings, and seals.
2) The assembly procedure which includes measuring clearances, installing bearings and seals, and adjusting the pinion depth using shims.
3) Tightening the pinion nut to the specified torque and reinstalling the front axle assembly onto the machine.
The document provides instructions for disassembling and assembling the cylinder head of a D11R track-type tractor. It describes removing components like the cylinder head, valves, valve guides, and valve lifters. It then describes the process for assembling these components in reverse order, noting that parts should be kept clean and lubricated with engine oil during assembly. Tools are listed for tasks like compressing valve springs and installing valve guides.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) system on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show the components and steps to disassemble and reassemble the RPTO. Separate sections provide procedures for removing and installing the vibration damper and pulley.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing the front oil seal from the housing.
3) Cleaning surfaces and installing the front oil seal and housing back onto the cylinder block using thread lock compound on the bolts.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive planetary carriers can be removed in the chassis. Instructions are also given for disassembling and assembling the final drives and oil filter, which involves removing seals, gears, and other components and cleaning parts before reassembly.
This document provides instructions for disassembling and assembling components of the right planetary and brake, power train oil pump, and other parts of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, removing gears, discs, seals, and other parts. It then provides 22 steps to reassemble the components. A separate section provides 12 steps to remove and install the power train oil pump, disconnecting hoses and removing mounting bolts.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3516B engine used in a 994K wheel loader. The removal process involves draining coolant, removing connecting tubes and bolts, and lifting off the cylinder head. The installation is the reverse, and includes cleaning surfaces, installing new seals and gaskets, and torquing bolts in a specific sequence. Valves, guides, and other components are also removed and installed using various tools as outlined in the procedure.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3516E engine. It outlines the required tools and gives step-by-step procedures for disassembling and assembling the cylinder head components, including removing and installing the cylinder head, valves, valve guides, valve seat inserts, and valve lifters. Safety notices are provided throughout to warn technicians of potential hazards during disassembly and assembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 992K wheel loader with a C32 engine, including:
1) The crankshaft front seal using various tools to puncture, pry, and remove the seal and sleeve.
2) The front gear group using bolts, plates and shafts.
3) The front housing using bolts, seals and lifting equipment to remove the heavy component.
4) The valve mechanism cover using bolts and seals after loosening breathers and hoses.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. Cleanliness is emphasized during assembly and disassembly.
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 992K wheel loader with a C32 engine. The removal procedure involves using various tools to puncture the seal, pry off the wear sleeve, and pull the seal off. For installation, the seal and sleeve are installed together using a locator and installer tool. Overall instructions are provided for cleaning parts and ensuring proper installation orientation.
This document provides instructions for connecting the loader frame to the rear frame of a 966H wheel loader. It involves installing bearing assemblies and seals in the upper and lower hitches using various tools. Proper lubrication and torque specifications are emphasized. The process includes 20 steps such as installing lip seals in caps, positioning shims to achieve the correct rolling torque, and bolting the caps back onto the frames.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1. Using a valve spring compressor tool to remove valve locks, rotators, springs and valves.
2. Cleaning and lubricating valves before reinstalling them along with springs, rotators and locks using the compressor tool.
3. The procedure warns of potential injury from parts propelled by spring force.
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It involves using various tools to install a fuel pump timing pin and weight assembly, and tightening bolts to specified torques. The instructions describe removing the fuel injection pump housing and governor from the engine, which requires following other removal procedures first and using lifting equipment due to the heavy weight of the components.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, including removing bolts, valves, sensors, gears, and other components. It then lists 29 steps for assembly, instructing technicians to clean parts, press components together, and torque bolts to the specified values. The overall procedure involves carefully separating and then reassembling each part of the torque converter.
The document provides instructions for separating and disassembling components of a torque converter. Key steps include:
1. Removing bolts and other hardware to separate the torque converter from the transmission and output transfer gears.
2. Further disassembling the torque converter by removing additional bolts, seals, bearings, and internal components like the impeller, stator, carrier shaft, and turbine.
3. Cleaning all parts thoroughly before inspection and replacing any worn or damaged parts during reassembly. The instructions detail reassembling the torque converter components in reverse order.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Clark GPX 35 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
The document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support the heavy components. The removal process involves removing bolts, installing lifting brackets, and using hydraulic tools to separate the carrier from the final drive. Precautions are listed for containing fluids during disassembly.
The document provides instructions for removing and installing the front axle of a M314F wheeled excavator. It details:
1) Removing the front axle assembly from the machine and disassembling it by removing components like the differential, bearings, and seals.
2) The assembly procedure which includes measuring clearances, installing bearings and seals, and adjusting the pinion depth using shims.
3) Tightening the pinion nut to the specified torque and reinstalling the front axle assembly onto the machine.
The document provides instructions for disassembling and assembling the cylinder head of a D11R track-type tractor. It describes removing components like the cylinder head, valves, valve guides, and valve lifters. It then describes the process for assembling these components in reverse order, noting that parts should be kept clean and lubricated with engine oil during assembly. Tools are listed for tasks like compressing valve springs and installing valve guides.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) system on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show the components and steps to disassemble and reassemble the RPTO. Separate sections provide procedures for removing and installing the vibration damper and pulley.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing the front oil seal from the housing.
3) Cleaning surfaces and installing the front oil seal and housing back onto the cylinder block using thread lock compound on the bolts.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive planetary carriers can be removed in the chassis. Instructions are also given for disassembling and assembling the final drives and oil filter, which involves removing seals, gears, and other components and cleaning parts before reassembly.
This document provides instructions for disassembling and assembling components of the right planetary and brake, power train oil pump, and other parts of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, removing gears, discs, seals, and other parts. It then provides 22 steps to reassemble the components. A separate section provides 12 steps to remove and install the power train oil pump, disconnecting hoses and removing mounting bolts.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3516B engine used in a 994K wheel loader. The removal process involves draining coolant, removing connecting tubes and bolts, and lifting off the cylinder head. The installation is the reverse, and includes cleaning surfaces, installing new seals and gaskets, and torquing bolts in a specific sequence. Valves, guides, and other components are also removed and installed using various tools as outlined in the procedure.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3516E engine. It outlines the required tools and gives step-by-step procedures for disassembling and assembling the cylinder head components, including removing and installing the cylinder head, valves, valve guides, valve seat inserts, and valve lifters. Safety notices are provided throughout to warn technicians of potential hazards during disassembly and assembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 992K wheel loader with a C32 engine, including:
1) The crankshaft front seal using various tools to puncture, pry, and remove the seal and sleeve.
2) The front gear group using bolts, plates and shafts.
3) The front housing using bolts, seals and lifting equipment to remove the heavy component.
4) The valve mechanism cover using bolts and seals after loosening breathers and hoses.
This document provides instructions for assembling and disassembling components of the powertrain for a Caterpillar 966H wheel loader, including:
1) Assembling the torque converter by installing various bearings, gears, and rings in the specified order and torque values.
2) Separating the transmission from the output transfer gears by removing bolts and using lifting tools.
3) Disassembling the transmission planetary by removing covers, gears, and shafts after separating it from other components and using various tools. Cleanliness is emphasized during assembly and disassembly.
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 992K wheel loader with a C32 engine. The removal procedure involves using various tools to puncture the seal, pry off the wear sleeve, and pull the seal off. For installation, the seal and sleeve are installed together using a locator and installer tool. Overall instructions are provided for cleaning parts and ensuring proper installation orientation.
This document provides instructions for connecting the loader frame to the rear frame of a 966H wheel loader. It involves installing bearing assemblies and seals in the upper and lower hitches using various tools. Proper lubrication and torque specifications are emphasized. The process includes 20 steps such as installing lip seals in caps, positioning shims to achieve the correct rolling torque, and bolting the caps back onto the frames.
This document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1. Using a valve spring compressor tool to remove valve locks, rotators, springs and valves.
2. Cleaning and lubricating valves before reinstalling them along with springs, rotators and locks using the compressor tool.
3. The procedure warns of potential injury from parts propelled by spring force.
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It involves using various tools to install a fuel pump timing pin and weight assembly, and tightening bolts to specified torques. The instructions describe removing the fuel injection pump housing and governor from the engine, which requires following other removal procedures first and using lifting equipment due to the heavy weight of the components.
This document provides instructions for assembling a torque converter for a 962G wheel loader. It outlines 38 steps for installing various components like bearings, seals, gears, and housing pieces. Tools required include link brackets, eyebolts, pliers, and retaining ring pliers. The assembly begins with installing inner components and ends by connecting the torque converter to the transmission and output gears.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, including removing bolts, valves, sensors, gears, and other components. It then lists 29 steps for assembly, instructing technicians to clean parts, press components together, and torque bolts to the specified values. The overall procedure involves carefully separating and then reassembling each part of the torque converter.
The document provides instructions for separating and disassembling components of a torque converter. Key steps include:
1. Removing bolts and other hardware to separate the torque converter from the transmission and output transfer gears.
2. Further disassembling the torque converter by removing additional bolts, seals, bearings, and internal components like the impeller, stator, carrier shaft, and turbine.
3. Cleaning all parts thoroughly before inspection and replacing any worn or damaged parts during reassembly. The instructions detail reassembling the torque converter components in reverse order.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. SERVICE MANUAL
T6.125 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6125*HEG01001 - ], T6.145 AutoCommand™ Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6145*HEG01001 - ],
T6.145 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6145*HEG01001 - ], T6.145 Standard - TIER 4B
(FINAL) and STAGE IV (Mother Regulation) [HACT6145*HEG01001 - ], T6.155
AutoCommand™ Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother
Regulation) [HACT6155*HEG01001 - ], T6.155 Dynamic Command Sidewinder
II - TIER 4B (FINAL) and STAGE IV (Mother Regulation) [HACT6155*HEG01001
- ], T6.155 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ], T6.160 Standard - TIER 4B (FINAL) and STAGE
IV (Mother Regulation) [HACT6160*KEG01001 - ], T6.165 AutoCommand™
Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ], T6.165 Dynamic Command Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6165*HEG01001 -
], T6.165 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ], T6.175 AutoCommand™ Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6175*HEG01001 - ],
T6.175 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6175*HEG01001 - ], T6.175 Standard - TIER 4B
(FINAL) and STAGE IV (Mother Regulation) [HACT6175*HEG01001 - ], T6.180
AutoCommand™ Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother
Regulation) [HACT6180*JEG01001 - ], T6.180 Dynamic Command Sidewinder
II - TIER 4B (FINAL) and STAGE IV (Mother Regulation) [HACT6180*HEG01001
- ], T6.180 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6180*HEG01001 - ]
51666744 24/01/2020
EN
3. Link Product / Engine
Product Market Product Engine
T6.145 AutoCommand™
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6145*HEG01001 - ]
Europe F4DFE414W*B001
T6.155 AutoCommand™
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ]
Europe F4DFE414X*B001
T6.165 AutoCommand™
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ]
Europe F4DFE414Y*B001
T6.175 AutoCommand™
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6175*HEG01001 - ]
Europe F4DFE414Z*B001
T6.180 AutoCommand™
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6180*JEG01001 - ]
Europe F4DFE614G*B002
T6.125 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6125*HEG01001 - ]
Europe F4DFE414D*B002
T6.145 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6145*HEG01001 - ]
Europe F4DFE4134*B011
T6.145 Dynamic Command
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6145*HEG01001 - ]
Europe F4DFE414W*B001
T6.155 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ]
Europe F4DFE4133*B014
T6.155 Dynamic Command
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ]
Europe F4DFE414X*B001
T6.160 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6160*KEG01001 - ]
Europe F4DFE614B*B002
T6.165 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ]
Europe F4DFE4132*B010
T6.165 Dynamic Command
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ]
Europe F4DFE414Y*B001
51666744 24/01/2020
4. Product Market Product Engine
T6.175 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6175*HEG01001 - ]
Europe F4DFE4131*B015
T6.175 Dynamic Command
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6175*HEG01001 - ]
Europe F4DFE414Z*B001
T6.180 Standard - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6180*HEG01001 - ]
Europe F4DFE6132*B007
T6.180 Dynamic Command
Sidewinder II - TIER 4B (FINAL)
and STAGE IV (Mother Regulation)
[HACT6180*HEG01001 - ]
Europe F4DFE614G*B002
51666744 24/01/2020
11. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your NEW HOLLAND Sales and Service Networks.
51666744 24/01/2020
3
12. INTRODUCTION
Foreword - How to use and navigate through this manual
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through web delivery (eTIM), DVD, and paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on their machine it is usually because a function or system on their ma-
chine is not working at all, is not working efficiently, or is not responding correctly to their commands. When you refer
to the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system, you will then find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies, and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system: the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting), and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - the component or function on the machine, that the piece of technical information is going to describe
(e.g., Fuel tank).
• INFORMATION TYPE - the piece of technical information that has been written for a particular component or func-
tion on the machine (e.g., Capacity would be a type of Technical Data describing the amount of fuel held by the fuel
tank).
• PRODUCT - the model for which the piece of technical information is written.
Every piece of technical information will have those three categories attached to it. You will be able to use any combi-
nation of those categories to find the right piece of technical information you need to resolve that customer's concern
on their machine.
That information could be:
• the procedure for how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
51666744 24/01/2020
4
13. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
51666744 24/01/2020
9
14. SERVICE MANUAL
Engine
T6.125 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6125*HEG01001 - ], T6.145 AutoCommand™ Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6145*HEG01001 - ],
T6.145 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6145*HEG01001 - ], T6.145 Standard - TIER 4B
(FINAL) and STAGE IV (Mother Regulation) [HACT6145*HEG01001 - ], T6.155
AutoCommand™ Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother
Regulation) [HACT6155*HEG01001 - ], T6.155 Dynamic Command Sidewinder
II - TIER 4B (FINAL) and STAGE IV (Mother Regulation) [HACT6155*HEG01001
- ], T6.155 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ], T6.160 Standard - TIER 4B (FINAL) and STAGE
IV (Mother Regulation) [HACT6160*KEG01001 - ], T6.165 AutoCommand™
Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ], T6.165 Dynamic Command Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6165*HEG01001 -
], T6.165 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ], T6.175 AutoCommand™ Sidewinder II - TIER
4B (FINAL) and STAGE IV (Mother Regulation) [HACT6175*HEG01001 - ],
T6.175 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6175*HEG01001 - ], T6.175 Standard - TIER 4B
(FINAL) and STAGE IV (Mother Regulation) [HACT6175*HEG01001 - ], T6.180
AutoCommand™ Sidewinder II - TIER 4B (FINAL) and STAGE IV (Mother
Regulation) [HACT6180*JEG01001 - ], T6.180 Dynamic Command Sidewinder
II - TIER 4B (FINAL) and STAGE IV (Mother Regulation) [HACT6180*HEG01001
- ], T6.180 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6180*HEG01001 - ]
51666744 24/01/2020
10
15. Engine - Engine and crankcase
Engine - Remove
T6.125 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6125*HEG01001 - ]
WE
T6.145 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6145*HEG01001 - ]
WE
T6.145 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6145*HEG01001 - ]
WE
T6.155 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6155*HEG01001 - ]
WE
T6.155 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6155*HEG01001 - ]
WE
T6.160 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6160*KEG01001 - ]
WE
T6.165 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6165*HEG01001 - ]
WE
T6.165 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6165*HEG01001 - ]
WE
T6.175 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6175*HEG01001 - ]
WE
T6.175 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6175*HEG01001 - ]
WE
T6.180 Dynamic Command Sidewinder II - TIER 4B (FINAL) and STAGE IV
(Mother Regulation) [HACT6180*HEG01001 - ]
WE
T6.180 Standard - TIER 4B (FINAL) and STAGE IV (Mother Regulation)
[HACT6180*HEG01001 - ]
WE
Prior operation:
Discharge the air conditioning system, see Air conditioning - Discharging (50.200) Air conditioning - Evacuate
(50.200).
Prior operation:
Disconnect the battery, see Battery - Disconnect (55.302)
Prior operation:
Remove the left-hand fuel tank, see Fuel tank - Remove (10.216)
Prior operation:
Remove the engine hood, see Hood - Remove (90.100)
Prior operation:
Remove the front frame, see Front frame - Remove (39.100)
Prior operation:
Remove the selective catalytic reduction (SRC) muffler, see Selective Catalytic Reduction (SCR) muffler and cat-
alyst - Remove (10.500)
Prior operation:
Remove the coolant control valve, see Coolant control valve - Remove (10.500)
WARNING
Heavy objects!
Lift and handle all heavy components using lift-
ing equipment with adequate capacity. Always
support units or parts with suitable slings or
hooks. Make sure the work area is clear of all
bystanders.
Failure to comply could result in death or seri-
ous injury.
W0398A
WARNING
Avoid injury!
Handle all parts carefully. Do not place your
hands or fingers between parts. Use Personal
Protective Equipment (PPE) as indicated in this
manual, including protective goggles, gloves,
and safety footwear.
Failure to comply could result in death or seri-
ous injury.
W0208A
51666744 24/01/2020
10.1 [10.001] / 3
16. Engine - Engine and crankcase
NOTICE: Emissions sensors mounted in the exhaust stream are sensitive to extreme vibrations. Use of tools that
generate extreme vibrations, such as impact wrenches and hammers, will result in damage to emission sensors.
Avoid using these tools during any service procedure in close proximity of emission sensors. If the use of these tools
cannot be avoided, remove the sensors using extreme caution prior to performing any service procedure.
All Vehicles
1. Drain the transmission oil.
A. Remove the transmission housing drain plug and
drain the transmission oil into a suitable container.
B. Install the drain plug and torque to 68 – 82 N·m (50
– 60 lb ft).
BAIL14TR00962AB 1
2. Disconnect the oil cooler supply and return pipes.
BAIL14TR00882AB 2
3. Remove the oil cooler supply and return pipes.
BAIL14TR00883AB 3
51666744 24/01/2020
10.1 [10.001] / 4
17. Engine - Engine and crankcase
4. • Disconnect the alternator electrical connector.
• Disconnect the in-line electrical connector.
BAIL14TR00936AB 4
5. Remove the side panel mounting bracket.
BAIL14TR00937AB 5
6. Remove the starter motor shield.
A. Cut the cable ties.
B. Remove the starter motor shield retaining bolts.
BAIL14TR00938AB 6
7. Disconnect the starter motor electrical connectors.
BAIL14TR00884AB 7
51666744 24/01/2020
10.1 [10.001] / 5
18. Engine - Engine and crankcase
8. 1. Disconnect the starter motor negative terminal.
2. Disconnect the cab heater supply pipe.
3. Detach the cab heater supply pipe.
BAIL14TR00885AB 8
9. Detach the cab heater supply pipe.
BAIL14TR00886AB 9
10. Disconnect the block heater electrical connector (if fit-
ted).
BAIL14TR00887AB 10
11. Disconnect the heater supply hose from the rear of the
cylinder head.
BAIL12APH145AVA 11
51666744 24/01/2020
10.1 [10.001] / 6
19. Engine - Engine and crankcase
12. Disconnect the engine breather pipe.
BAIL14TR00888AB 12
13. 1. Disconnect the brake fluid reservoir electrical con-
nector.
2. Remove the brake fluid reservoir heat shield.
BAIL15TR00026AA 13
14. Detach the brake fluid reservoir and position it to one
side.
BAIL14TR00939AB 14
15. Disconnect the steering pipes.
NOTE: Mark the pipes to aid installation.
BAIL14TR00940AB 15
51666744 24/01/2020
10.1 [10.001] / 7
20. Engine - Engine and crankcase
16. Remove the fuel line.
BAIL14TR00941AB 16
17. 1. Disconnect the electrical connector (1).
2. Detach the wiring harness (2) from the bracket.
3. Remove the bracket.
BAIL14TR00943AB 17
18. Disconnect the A/C compressor high pressure pipe
and position it to one side.
BAIL14TR00970AB 18
19. Disconnect the water-in-fuel electrical connector.
BAIL14TR00948AB 19
51666744 24/01/2020
10.1 [10.001] / 8
21. Engine - Engine and crankcase
20. Disconnect the differential lock supply pipe.
BAIL14TR00949AB 20
21. 1. Disconnect the in-line electrical connector.
2. Detach the wiring harness from the clip.
3. Cut the cable tie.
NOTICE: Seal all openings using clean blanking plugs.
BAIL14TR00950AB 21
22. 1. Disconnect the in-line electrical connector.
2. Detach the wiring harness from the clip.
BAIL14TR00952AB 22
23. 1. Disconnect the intake air temperature (IAT) sen-
sor electrical connector.
2. Disconnect the air cleaner sensor electrical con-
nectors.
BAIL14TR00971AB 23
51666744 24/01/2020
10.1 [10.001] / 9
22. Engine - Engine and crankcase
24. Disconnect the DEF/ADBLUE® dosing module electri-
cal connector.
BAIL14TR00954AB 24
25. Disconnect the nitrogen oxide (NOx) module electrical
connector.
BAIL14TR00972AB 25
26. 1. Detach the wiring harness from the clips.
2. Disconnect the in-line electrical connector.
BAIL14TR00964AB 26
27. Detach the engine emission filter.
A. Disconnect the engine emission hose (1) from the
bottom of the engine emission filter.
B. Remove the engine emission filter retaining bolts
(2).
C. Detach the engine emission hose (3) from the
retaining clip.
BAIL14TR00973AC 27
51666744 24/01/2020
10.1 [10.001] / 10
23. Engine - Engine and crankcase
28. • Disconnect the coolant expansion tank lower hose.
• Disconnect the exhaust flap coolant hose.
• Disconnect the turbocharger air intake tube.
BAIL14TR00974AB 28
29. 1. Disconnect the coolant line from the DEF/
ADBLUE® dosing module.
2. Disconnect the DEF/ADBLUE® lines from the
DEF/ADBLUE® dosing module.
BAIL14TR00975AB 29
30. Remove the air cleaner frame retaining bolts.
BAIL14TR00976AB 30
31. With the aid of another technician, remove the air
cleaner frame.
BAIL14TR00986AB 31
51666744 24/01/2020
10.1 [10.001] / 11
24. Engine - Engine and crankcase
32. Remove the DEF/ADBLUE® lines.
BAIL14TR00977AB 32
33. 1. Disconnect the turbocharger oil pipes.
2. Disconnect the turbocharger electrical connector.
3.
BAIL14TR00978AB 33
34. 1. Disconnect the exhaust flap to turbocharger
clamp.
2. Remove the turbocharger mounting bracket re-
taining bolts.
BAIL14TR00987AB 34
35. 1. Remove the engine upper frame retaining bolt.
2. Remove the engine upper frame retaining nuts.
BAIL14TR00988AB 35
51666744 24/01/2020
10.1 [10.001] / 12
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Engine - Engine and crankcase
36. 1. Remove the engine upper frame retaining bolt.
2. Remove the engine upper frame retaining bolts.
3. Remove the engine upper frame retaining nuts.
BAIL14TR00989AB 36
37. Remove the engine upper frame retaining bolts.
BAIL14TR00990AB 37
38. Using suitable lifting equipment, remove the engine
upper frame and diesel oxidation catalyst (DOC) as-
sembly.
BAIL15TR00019AA 38
39. Remove the fuel line from the rear of the cylinder
head.
BAIL15TR00020AA 39
51666744 24/01/2020
10.1 [10.001] / 13
27. Engine - Engine and crankcase
40. Detach the grid heater relay and position it to one side.
BAIL15TR00021AA 40
41. Remove the engine rear frame right-hand side retain-
ing bolts.
BAIL15TR00022AA 41
42. Remove the engine rear frame.
BAIL15TR00023AA 42
43. Disconnect the steering motor pipes.
BAIL15TR00024AA 43
51666744 24/01/2020
10.1 [10.001] / 14
28. Engine - Engine and crankcase
44. Install three engine lifting eyes 380200013.
BAIL07APH141BVA 44
45. Remove the engine to transmission lower inner retain-
ing bolts.
BAIL14TR00968AB 45
46. Remove the engine to transmission lower outer retain-
ing bolts.
BAIL14TR00969AB 46
51666744 24/01/2020
10.1 [10.001] / 15