The document provides information on tractor engines, including general specifications, recommended tightening torques, necessary tools, and an engine view diagram. Sections cover the engine, clutch, transmissions, drive lines, brakes, hydraulics, steering, axles, electrical systems, and more.
New holland t5030 tractor service repair manualfujdjffjkskemme
The document provides information on tractor engines, including general specifications, torque specifications, special tools, and an engine view diagram. It covers topics such as the engine model, cooling system, lubrication system, fuel system, intake and exhaust systems. Key components discussed include the cylinder block, cylinder head, pistons, crankshaft, camshaft, valves and valve train.
Steyr 4075 kompakt tractor service repair manualfuhsejskekmmm
This document is a service manual for KOMPAKT TRACTORS models 4065-4075-4085-4095. It contains sections covering general guidelines, the engine, clutch, transmissions, drive lines, mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, air conditioning, electrical systems, platform/cab/bodywork, and technical support. Safety regulations are provided, warning technicians to take precautions such as disconnecting the battery and avoiding working on engines while they are running.
New holland tn75 fa tractor service repair manualufjjsjfkememe
This document is a service manual for TN75FA-TN85FA-TN95FA tractors. It contains sections on general guidelines, the engine, clutch, transmissions, and other systems. Each section provides specifications, diagrams, removal and installation instructions, and procedures for inspection and repair. The manual is intended exclusively for use by trained New Holland technicians.
New holland tm175 tractor service repair manualufjjsjfkememe
This document is a repair manual that provides instructions for servicing TM120, TM130, TM140, TM155, TM175, and TM190 tractors. It contains sections covering the general information, engine, clutch, transmission, drivelines, front and rear axles, brakes, hydraulics, steering, electrical systems, and cab. Safety precautions and maintenance instructions are provided throughout. The manual is intended solely for use by authorized service technicians according to the specific guidelines and procedures outlined.
New holland tk4050 tractor service repair manualufjjsjfkememe
This service manual provides maintenance and repair instructions for various tractor models including the TK4020F, TK4040, and TK4060. The manual includes sections on the engine, clutch, transmission, rear axle, power take-off, brakes, hydraulics, steering, tracks, electrical systems, and cab/body. The document provides detailed procedures and specifications for removing and servicing components of the tractors.
New holland td95 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland td90 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland t5030 tractor service repair manualfujdjffjkskemme
The document provides information on tractor engines, including general specifications, torque specifications, special tools, and an engine view diagram. It covers topics such as the engine model, cooling system, lubrication system, fuel system, intake and exhaust systems. Key components discussed include the cylinder block, cylinder head, pistons, crankshaft, camshaft, valves and valve train.
Steyr 4075 kompakt tractor service repair manualfuhsejskekmmm
This document is a service manual for KOMPAKT TRACTORS models 4065-4075-4085-4095. It contains sections covering general guidelines, the engine, clutch, transmissions, drive lines, mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, air conditioning, electrical systems, platform/cab/bodywork, and technical support. Safety regulations are provided, warning technicians to take precautions such as disconnecting the battery and avoiding working on engines while they are running.
New holland tn75 fa tractor service repair manualufjjsjfkememe
This document is a service manual for TN75FA-TN85FA-TN95FA tractors. It contains sections on general guidelines, the engine, clutch, transmissions, and other systems. Each section provides specifications, diagrams, removal and installation instructions, and procedures for inspection and repair. The manual is intended exclusively for use by trained New Holland technicians.
New holland tm175 tractor service repair manualufjjsjfkememe
This document is a repair manual that provides instructions for servicing TM120, TM130, TM140, TM155, TM175, and TM190 tractors. It contains sections covering the general information, engine, clutch, transmission, drivelines, front and rear axles, brakes, hydraulics, steering, electrical systems, and cab. Safety precautions and maintenance instructions are provided throughout. The manual is intended solely for use by authorized service technicians according to the specific guidelines and procedures outlined.
New holland tk4050 tractor service repair manualufjjsjfkememe
This service manual provides maintenance and repair instructions for various tractor models including the TK4020F, TK4040, and TK4060. The manual includes sections on the engine, clutch, transmission, rear axle, power take-off, brakes, hydraulics, steering, tracks, electrical systems, and cab/body. The document provides detailed procedures and specifications for removing and servicing components of the tractors.
New holland td95 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland td90 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland td80 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland t6070 power command tractor service repair manualufjjsjfkememe
The document is a service manual that provides technical data, functional descriptions, diagrams, and repair procedures for the primary hydraulic power system on various tractor models. It describes the hydraulic pump, charge pump, compensator, and filtration system. The hydraulic pump section includes specifications, diagrams, and instructions for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump. The manual provides information needed to maintain and repair the primary hydraulic system.
New holland t6050 range command tractor service repair manualufjjsjfkememe
The document is a service manual that provides technical specifications, descriptions of operation, and maintenance/repair procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland t4060 v tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4030N, T4040N, T4050N, T4060N, T4020V, T4030V, T4040V, and T4050V. It provides the engine type for each tractor model and market region combination, linking the product code to the appropriate engine. The manual contains model year ranges, identification codes, and markets for coverage of the listed tractor models.
New holland t4060 n tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4030N, T4040N, T4050N, T4060N, T4020V, T4030V, T4040V, and T4050V. It provides the engine type for each tractor model and market region combination, linking the product code to the appropriate engine. The manual contains model year ranges, identification codes, and markets for coverage of the listed tractor models.
New holland t4040 deluxe tractor service repair manualufjjsjfkememe
This document is a service manual for T4020, T4030, T4040, and T4050 tractor models. It contains sections on general guidelines, the engine, clutch, transmissions, drive lines, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, cab air conditioning, electrical system, platform/cab/bodywork, and technical support. Each section provides specifications, diagrams, removal and installation instructions, disassembly and assembly procedures, adjustments, and fault finding information.
New holland t9.480 tier 4 b (final) tractor service repair manualufjjsjfkememe
This document contains safety guidelines for operating agricultural tractors and equipment. It outlines general safety rules regarding slopes, passengers, impaired operation, hitching implements, overhead hazards, and more. Personal protective equipment is recommended. Machine components should be inspected before operation and guards kept in place. Proper shutdown and parking procedures help prevent injury or accidents.
New holland t9.450 [zcf200001 ] tractor service repair manualufjjsjfkememe
This document is a service manual for Case IH T9.390, T9.450, T9.505, T9.560, T9.615, and T9.670 tractors. It provides instructions for removing and installing the engine and crankcase on the different tractor models, which include 9L tractors, 13L single turbo tractors, and 13L two stage turbocharger tractors. The manual also contains sections on other engine components like air cleaners, cooling systems, and exhaust systems.
New holland t8.435 continuously variable transmission (cvt) tractor service r...ufjjsjfkememe
This document is a service manual that provides instructions for servicing and repairing the engines and components of T8 tractor models. It contains over 200 sections organized by vehicle system, with each section providing removal and installation instructions, part numbers, specifications and diagrams. Safety information is provided at the beginning regarding personal protective equipment and safety procedures.
New holland t8.410 smart trax powershift transmission (pst) tractor service r...ufjjsjfkememe
The document is a service manual that provides information on servicing and repairing various components of CNH Industrial T8 series tractors, including the T8.320, T8.350, T8.380, T8.410, T8.380 SmartTrax, and T8.410 SmartTrax models. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, and other areas. The introductory section provides safety guidelines and identifies the engine as a 6-cylinder, turbocharged and aftercooled Fiat Powertrain Technologies Cursor 9 engine with common rail fuel injection and SCR emissions control.
New holland t8.410 powershift transmission (pst) tractor service repair manualufjjsjfkememe
The document is a service manual that provides information on servicing and repairing various components of CNH Industrial T8 series tractors, including the T8.320, T8.350, T8.380, T8.410, T8.380 SmartTrax, and T8.410 SmartTrax models. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, and other areas. The introductory section provides safety guidelines and identifies the engine as a 6-cylinder, turbocharged and aftercooled Fiat Powertrain Technologies Cursor 9 engine with common rail fuel injection and SCR emissions control.
New holland t8.320 powershift transmission (pst) tractor service repair manualufjjsjfkememe
Plug or cap all ports and lines.
RAIL13TR04235AA 13
14. Remove the two bolts (1) securing the oil cooler to the
engine.
RAIL13TR04236AA 14
47794972 10/11/2014
10.1 [10.001] / 6
Engine - Engine and crankcase
15. Disconnect the wiring harness connectors (1) from the
engine.
RAIL13TR04238AA 15
16. Disconnect the fuel lines (1) from the fuel injection
pump. Plug or cap the lines.
RAIL13TR04239AA 16
17. Remove the two bolts (1) securing the fuel
New holland t5.115 tractor service repair manualufjjsjfkememe
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New holland t4.95 n tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4.75N/T4.85N/T4.95N/T4.105N and T4.65V/T4.75V/T4.85V/T4.95V/T4.105V. It contains information on engine service, clutches, transmissions, differentials, front and rear axle systems, power take-off systems, brakes, hydraulic systems, hitches and couplings, steering, wheels, cab climate control, electrical systems, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for technicians, listed by system and component.
New holland boomer 54 d cvt tier 4b (final) compact tractor service repair ma...ufjjsjfkememe
This service manual provides instructions for servicing a Boomer 54D CVT compact tractor with a Tier 4B final engine. It covers removing and servicing components of the engine, transmission, axles, brakes, hydraulics and other systems. The document includes safety information, specifications, diagrams and step-by-step instructions for maintenance, repair and replacement of parts. Proper qualifications and safety precautions are required to perform the service procedures.
Hyster k005 (h5.50 xm europe) forklift service repair manualufjjsjfkememe
This document provides repair procedures for a lift truck counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. It includes descriptions of each component and instructions for their removal and installation. Safety warnings are provided, such as the need to block the lift truck when removing heavy components to prevent tipping. Counterweight removal requires lifting devices and eyebolts. Hood, lights, and restraint adjustments must be correctly done for safety. The radiator draining and refilling process is outlined.
Hyster g019 (h13.00 xm europe) forklift service repair manualufjjsjfkememe
This document provides instructions for servicing the hydraulic tank on a lift truck. The key steps are:
1. Drain the hydraulic oil from the tank and disconnect all hoses and connections.
2. Remove the tank from the frame by taking off mounting bolts and moving electrical cables.
3. Inspect and clean the tank, which may involve steam cleaning or chemical solutions. Welding repairs for large leaks must be done by an authorized technician.
4. Reinstall the tank by reversing the removal steps and refilling the hydraulic oil. Safety precautions are provided throughout to avoid sparks or damage to electronic components.
Hyster b454 (w40 zc) forklift service repair manualufjjsjfkememe
This document provides safety procedures for working near a mast and repair procedures for a reach carriage. When working near a mast, it must be fully lowered or secured with safety chains. Repairs should only be done by trained technicians. The reach carriage can be removed from the mast for repairs. Procedures are provided for removing and replacing parts like the load backrest, forks, and load rollers. Safety precautions are emphasized, including using lifting devices and securing heavy parts to prevent injuries.
Cummins onan otpcb transfer switch 40 1000 amperes service repair manualufjjsjfkememe
This document is a service manual that describes the components, operation, and maintenance of various transfer switch models ranging from 40 to 1000 amperes. It provides detailed information on the transfer switch components, functional programs, control features, and removal/replacement of electronic control components. The manual is intended to guide service technicians on the operation and servicing of these transfer switches.
Cummins onan generator set with power command 3100 controller model (dfga ) s...ufjjsjfkememe
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance/repair procedures for various generator set parts.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
New holland td80 d tractor service repair manualufjjsjfkememe
This document is the service manual for TD60D-TD95D model tractors. It contains sections on general information, the engine, clutch, gearbox, transmission of motion, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, auxiliary equipment, electrical system, and cab. Each section provides specifications, removal and installation instructions, overhaul procedures, and troubleshooting information for the corresponding system.
New holland t6070 power command tractor service repair manualufjjsjfkememe
The document is a service manual that provides technical data, functional descriptions, diagrams, and repair procedures for the primary hydraulic power system on various tractor models. It describes the hydraulic pump, charge pump, compensator, and filtration system. The hydraulic pump section includes specifications, diagrams, and instructions for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump. The manual provides information needed to maintain and repair the primary hydraulic system.
New holland t6050 range command tractor service repair manualufjjsjfkememe
The document is a service manual that provides technical specifications, descriptions of operation, and maintenance/repair procedures for the primary hydraulic power system on various tractor models. It includes information on the variable displacement hydraulic pump, charge pump, compensator, filters, and pressure testing procedures. The hydraulic pump section covers specifications, operation, component views, and procedures for removal, overhaul, assembly, installation, and pressure testing of the variable displacement pump.
New holland t4060 v tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4030N, T4040N, T4050N, T4060N, T4020V, T4030V, T4040V, and T4050V. It provides the engine type for each tractor model and market region combination, linking the product code to the appropriate engine. The manual contains model year ranges, identification codes, and markets for coverage of the listed tractor models.
New holland t4060 n tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4030N, T4040N, T4050N, T4060N, T4020V, T4030V, T4040V, and T4050V. It provides the engine type for each tractor model and market region combination, linking the product code to the appropriate engine. The manual contains model year ranges, identification codes, and markets for coverage of the listed tractor models.
New holland t4040 deluxe tractor service repair manualufjjsjfkememe
This document is a service manual for T4020, T4030, T4040, and T4050 tractor models. It contains sections on general guidelines, the engine, clutch, transmissions, drive lines, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, axle and wheels, cab air conditioning, electrical system, platform/cab/bodywork, and technical support. Each section provides specifications, diagrams, removal and installation instructions, disassembly and assembly procedures, adjustments, and fault finding information.
New holland t9.480 tier 4 b (final) tractor service repair manualufjjsjfkememe
This document contains safety guidelines for operating agricultural tractors and equipment. It outlines general safety rules regarding slopes, passengers, impaired operation, hitching implements, overhead hazards, and more. Personal protective equipment is recommended. Machine components should be inspected before operation and guards kept in place. Proper shutdown and parking procedures help prevent injury or accidents.
New holland t9.450 [zcf200001 ] tractor service repair manualufjjsjfkememe
This document is a service manual for Case IH T9.390, T9.450, T9.505, T9.560, T9.615, and T9.670 tractors. It provides instructions for removing and installing the engine and crankcase on the different tractor models, which include 9L tractors, 13L single turbo tractors, and 13L two stage turbocharger tractors. The manual also contains sections on other engine components like air cleaners, cooling systems, and exhaust systems.
New holland t8.435 continuously variable transmission (cvt) tractor service r...ufjjsjfkememe
This document is a service manual that provides instructions for servicing and repairing the engines and components of T8 tractor models. It contains over 200 sections organized by vehicle system, with each section providing removal and installation instructions, part numbers, specifications and diagrams. Safety information is provided at the beginning regarding personal protective equipment and safety procedures.
New holland t8.410 smart trax powershift transmission (pst) tractor service r...ufjjsjfkememe
The document is a service manual that provides information on servicing and repairing various components of CNH Industrial T8 series tractors, including the T8.320, T8.350, T8.380, T8.410, T8.380 SmartTrax, and T8.410 SmartTrax models. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, and other areas. The introductory section provides safety guidelines and identifies the engine as a 6-cylinder, turbocharged and aftercooled Fiat Powertrain Technologies Cursor 9 engine with common rail fuel injection and SCR emissions control.
New holland t8.410 powershift transmission (pst) tractor service repair manualufjjsjfkememe
The document is a service manual that provides information on servicing and repairing various components of CNH Industrial T8 series tractors, including the T8.320, T8.350, T8.380, T8.410, T8.380 SmartTrax, and T8.410 SmartTrax models. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, and other areas. The introductory section provides safety guidelines and identifies the engine as a 6-cylinder, turbocharged and aftercooled Fiat Powertrain Technologies Cursor 9 engine with common rail fuel injection and SCR emissions control.
New holland t8.320 powershift transmission (pst) tractor service repair manualufjjsjfkememe
Plug or cap all ports and lines.
RAIL13TR04235AA 13
14. Remove the two bolts (1) securing the oil cooler to the
engine.
RAIL13TR04236AA 14
47794972 10/11/2014
10.1 [10.001] / 6
Engine - Engine and crankcase
15. Disconnect the wiring harness connectors (1) from the
engine.
RAIL13TR04238AA 15
16. Disconnect the fuel lines (1) from the fuel injection
pump. Plug or cap the lines.
RAIL13TR04239AA 16
17. Remove the two bolts (1) securing the fuel
New holland t5.115 tractor service repair manualufjjsjfkememe
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New holland t4.95 n tractor service repair manualufjjsjfkememe
This document is a service manual for tractor models T4.75N/T4.85N/T4.95N/T4.105N and T4.65V/T4.75V/T4.85V/T4.95V/T4.105V. It contains information on engine service, clutches, transmissions, differentials, front and rear axle systems, power take-off systems, brakes, hydraulic systems, hitches and couplings, steering, wheels, cab climate control, electrical systems, and the platform, cab, bodywork and decals. The manual provides maintenance and repair instructions for technicians, listed by system and component.
New holland boomer 54 d cvt tier 4b (final) compact tractor service repair ma...ufjjsjfkememe
This service manual provides instructions for servicing a Boomer 54D CVT compact tractor with a Tier 4B final engine. It covers removing and servicing components of the engine, transmission, axles, brakes, hydraulics and other systems. The document includes safety information, specifications, diagrams and step-by-step instructions for maintenance, repair and replacement of parts. Proper qualifications and safety precautions are required to perform the service procedures.
Hyster k005 (h5.50 xm europe) forklift service repair manualufjjsjfkememe
This document provides repair procedures for a lift truck counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. It includes descriptions of each component and instructions for their removal and installation. Safety warnings are provided, such as the need to block the lift truck when removing heavy components to prevent tipping. Counterweight removal requires lifting devices and eyebolts. Hood, lights, and restraint adjustments must be correctly done for safety. The radiator draining and refilling process is outlined.
Hyster g019 (h13.00 xm europe) forklift service repair manualufjjsjfkememe
This document provides instructions for servicing the hydraulic tank on a lift truck. The key steps are:
1. Drain the hydraulic oil from the tank and disconnect all hoses and connections.
2. Remove the tank from the frame by taking off mounting bolts and moving electrical cables.
3. Inspect and clean the tank, which may involve steam cleaning or chemical solutions. Welding repairs for large leaks must be done by an authorized technician.
4. Reinstall the tank by reversing the removal steps and refilling the hydraulic oil. Safety precautions are provided throughout to avoid sparks or damage to electronic components.
Hyster b454 (w40 zc) forklift service repair manualufjjsjfkememe
This document provides safety procedures for working near a mast and repair procedures for a reach carriage. When working near a mast, it must be fully lowered or secured with safety chains. Repairs should only be done by trained technicians. The reach carriage can be removed from the mast for repairs. Procedures are provided for removing and replacing parts like the load backrest, forks, and load rollers. Safety precautions are emphasized, including using lifting devices and securing heavy parts to prevent injuries.
Cummins onan otpcb transfer switch 40 1000 amperes service repair manualufjjsjfkememe
This document is a service manual that describes the components, operation, and maintenance of various transfer switch models ranging from 40 to 1000 amperes. It provides detailed information on the transfer switch components, functional programs, control features, and removal/replacement of electronic control components. The manual is intended to guide service technicians on the operation and servicing of these transfer switches.
Cummins onan generator set with power command 3100 controller model (dfga ) s...ufjjsjfkememe
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance/repair procedures for various generator set parts.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. SECTION 00 -- GENERAL -- CHAPTER 1 1
87679925A -- 12 -- 2007
GENERAL INSTRUCTIONS
IMPORTANT NOTICE
All maintenance and repair work described in this manual must be performed exclusively by NEW HOLLAND
service technicians, in strict accordance with the instructions given and using any specific tools necessary.
Anyone performing the operations described herein without strictly following the instructions is personally
responsible for any eventual injury or damage to property.
SHIMMING
For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add
up the recorder values: Do not rely on measuring the entire shimming set, which may be incorrect, or the rated
value indicated for each on shim.
ROTATING SHAFT SEALS
For correct rotating shaft seal installation, proceed as follows:
-- before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes;
-- thoroughly clean the shaft and check that the working surface on the shaft is not damaged;
-- position the sealing lip facing the fluid; with hydrodynamic lips, take into consideration the shaft rotation
direction and position the grooves so that they will deviate the fluid towards the inner side of the seal;
-- coat the sealing lip with a thin layer of lubricant (use oil rather than grease) and fill the gap between the sealing
lip and the dust lip on double lip seals with grease;
-- insert the seal in its seat and press down using a flat punch; do not tap the seal with a hammer or mallet;
-- whilst inserting the seal, check that it is perpendicular to the seat; once settled, make sure that it makes
contact with the thrust element, if required;
-- to prevent damaging the seal lip on the shaft, position a protective guard during installation operations.
O--RING SEALS
Lubricate the O--RING seals before inserting them in the seats, this will prevent them from overturning and
twisting, which would jeopardise sealing efficiency.
SEALING COMPOUNDS
Apply one of the following sealing compounds on the mating surfaces marked with an X: RTV SILMATE,
RHODORSIL CAF 1 or LOCTITE PLASTIC GASKET.
Before applying the sealing compound, prepare the surfaces as follows:
-- remove any incrustations using a wire brush;
-- thoroughly de--grease the surfaces using one of the following cleaning agents: trichlorethylene, petrol or a
water and soda solution.
3. 2 SECTION 00 -- GENERAL -- CHAPTER 1
87679925A -- 12 -- 2007
BEARINGS
When installing bearings it is advised to:
-- heat the bearings to 80 ÷ 90 °C before fitting on the shafts;
-- allow the bearings to cool before installing them.
SPRING PINS
When fitting split socket elastic pins, ensure that the pin notch is positioned in the direction of the force required
to stress the pin.
Spiral spring pins do not require special positioning.
SPARE PARTS
Use solely genuine parts, which guarantee the same quality, duration and safety as the original parts as they
are identical to the ones fitted during production.
Only genuine parts can offer this guarantee.
When ordering spare parts, always provide the following information:
-- tractor model (commercial name) and frame number;
-- engine type and number;
-- part number of the ordered part, which can be found in the “Microfiches” or the “Spare Parts Catalogue”, used
for order processing.
NOTES FOR EQUIPMENT
The tools that NEW HOLLAND propose and illustrate in this manual are:
-- specifically researched and designed for use with NEW HOLLAND vehicles;
-- necessary to make reliable repair;
-- accurately built and strictly tested to offer efficient and long--lasting working means.
By using these tools, repair personnel will benefit from:
-- operating in optimal technical conditions;
-- obtaining the best results;
-- saving time and effort;
-- working in safe conditions.
IMPORTANT NOTES
Wear limit values indicated for certain parts are recommended, but not binding. The terms “front”, “rear”,
“right--hand” and “left--hand” (when referred to different parts) are intended as seen from the driving position with
the tractor in the normal direction of movement.
MOVING THE TRACTOR WITH THE BATTERY REMOVED
External power supply cables should only be connected to the respective positive and negative cable terminals,
using efficient clamps that guarantee adequate and secure contact.
Disconnect all services (lights, windshield wipers, etc.) before starting the vehicle.
If the vehicle electrical system requires checking, carry out operations with the power supply connected; once
checking is completed, disconnect all services and switch off the power supply before disconnecting the cables.
4. SECTION 00 -- GENERAL -- CHAPTER 1 3
87679925A -- 12 -- 2007
SAFETY REGULATIONS
WARNING AND DANGER SYMBOL
This warning symbol points out important messages concerning your safety.
Carefully read the following safety regulations and observe advised precautions in
order to avoid potential hazards and safeguard your health and safety.
In this manual the symbol is accompanied by the following key--words:
WARNING -- Warnings concerning unsuitable repair operations that may jeopardise
the safety of Repair personnel.
DANGER -- Specific warnings concerning potential hazards for operator safety or for
other persons directly or indirectly involved.
TO PREVENT ACCIDENTS
Most accidents or injuries that occur in workshops are
the result of non--observance of simple and
fundamental safety regulations.
For this reason, IN MOST CASES THESE
ACCIDENTS CAN BE AVOIDED: by foreseeing
possible causes and consequently acting with the
necessary caution and care.
Accidents may occur with all types of vehicle,
regardless of how well it was designed and built.
A careful and judicious service technician is the best
guarantee against accidents.
Precise observance of the most basic safety rule is
normally sufficient to avoid many serious accidents.
DANGER. Never carry out any cleaning, lubrication
or maintenance operations when the engine is
running.
SAFETY REGULATIONS
GENERAL
-- Carefully follow specified repair and maintenance
procedures.
-- Do not wear rings, wristwatches, jewellery,
unbuttoned or loose articles of clothing such as:
ties, torn clothing, scarves, open jackets or shirts
with open zips that may remain entangled in
moving parts.
It is advised to wear approved safety clothing,
e.g: non--slip footwear, gloves, safety goggles,
helmets, etc.
-- Do not carry out repair operations with someone
sitting in the driver’s seat, unless the person is a
trained technician who is assisting with the
operation in question.
-- Operate the vehicle and use the implements
exclusively from the driver’s seat.
-- Do not carry out operations on the vehicle withthe
engine running, unless specifically indicated.
-- Stop the engine and ensure that all pressure is
relieved from hydraulic circuits before removing
caps, covers, valves, etc.
-- All repair and maintenance operations must be
carried out using extreme care and attention.
-- Service steps and platforms used in a workshop
or in the field should be built in compliance with
the safety rules in force.
-- Disconnect the batteries and label all controls to
indicate that the vehicle is being serviced. Block
the machine and all equipment which should be
raised.
-- Do not check or fill fuel tanks, accumulator
batteries, nor use starting liquid when smoking or
near naked flames, as these fluids are
inflammable.
-- Brakes are inoperative if manually released for
repair or maintenance purposes.
Use blocks or similar devices to secure the
machine in these conditions.
-- The fuel nozzle should always be in contact with
the filling aperture. Maintain this position until
filling operations are completed in order to avoid
possible sparks caused by the accumulation of
static electricity.
5. 4 SECTION 00 -- GENERAL -- CHAPTER 1
87679925A -- 12 -- 2007
-- Only use specified towing points for towing the
tractor, connect parts carefully. Make sure that all
pins and/or locks are secured in position before
applying traction.
Never remain near the towing bars, cables or
chains that are operating under load.
-- Transport vehicles that cannot be driven using a
trailer or a low--loading platform trolley, if
available.
-- When loading or unloading the vehicle from the
trailer (or other means of transport), select a flat
area capable of sustaining the trailer or truck
wheels, firmly secure the tractor to the truck or
trailer and lock the wheels in the position.
-- Electric heaters, battery--chargers and similar
equipment must only be powered by auxiliary
power supplies with efficient ground insulation to
avoid electrical shock hazards.
-- Always use suitable hoisting or lifting devices
when raising or moving heavy parts.
-- Take extra care if bystanders are present.
-- Never pour gasoline or diesel oil into open, wide
and low containers.
-- Never use gasoline, diesel oil or other
inflammable liquids as cleaning agents. Use
non--inflammable, non toxic commercially
available solvents.
-- Wear safety goggles with side guards when
cleaning parts with compressed air.
-- Limit the air pressure to a maximum of 2.1 bar,
according to local regulations.
-- Do not run the engine in confined spaces without
suitable ventilation.
-- Do not smoke, use naked flames, or cause
sparks in the area when fuel filling or handling
highly inflammable liquids.
-- Never use naked flames forlighting whenworking
on the machine or checking for leaks.
-- All movements must be carried out carefully
when working under, on or near the vehicle and
wear protective equipment: helmets, gogglesand
special footwear.
-- When carrying out checks with the engine
running, request the assistance of an operator in
the driver’s seat. The operator must maintain
visual contact with the service technician at all
times.
-- If operating outside the workshop, position the
vehicle on a flat surface and lock in position. If
working on a slope, lock the vehicle in position
and move to a flat area as soon as is safely
possible.
-- Damaged or bent chains or cables are unreliable.
Do not use them for lifting or towing.
Always use suitable protective gloves when
handling chains or cables.
-- Chains should always be safely secured. Make
sure that the hitch--up point is capable of
sustaining the load in question.
Keep the area near the hitch--up point, chains or
cables free of all bystanders.
-- Maintenance and repair operations must be
carried out in a CLEAN and DRY area, eliminate
any water or oil spillage immediately.
-- Do not create piles of oil or grease--soaked rags
as they represent a serious fire hazard; store
them in a closed metal container.
Before starting the vehicle or implements, make
sure that the driver’s seat is locked in position and
always check that the area is free of persons or
obstacles.
-- Empty pockets of all objects that may fall
unobserved into the vehicle parts when
disassembled.
-- In the presence of protruding metal parts, use
protective goggles or goggles with side guards,
helmets, special footwear and gloves.
-- When welding, use protective safety devices:
tinted safety goggles, helmets, special overalls,
gloves and footwear. All persons present in the
area where welding is taking place must wear
tinted goggles.
NEVER LOOK DIRECTLY AT THE WELDING
ARC WITHOUT SUITABLE EYE PROTEC-
TION.
-- Metal cables tend to fray with repeated use.
Always use suitable protective devices (gloves,
goggles, etc.) when handling cables.
-- Handle all parts carefully, do not put your hands
or fingers between moving parts, wear suitable
safety clothing -- safety goggles, gloves and
shoes.
10. SECTION 10 -- ENGINE -- CHAPTER 1 15
87679925A -- 12 -- 2007
ENGINE R.I.
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks. Ensure that
no--one is in the vicinity of the load to be lifted.
ATTENTION
Use suitable tools to align the holes. NEVER USE
FINGERS OR HANDS.
1. Remove the bonnet (1) as described, see
section 90.
2. Disconnect the battery negative cable.
3. Drain the oil from the transmission--gearbox
housing. 1
4. Remove the retaining bolts (1) and the guard (2)
on the right--hand side of the fan, then remove the
four bolts retaining the mechanical battery
cut--out switch (1) from the guard.
2
5. Unscrew the control unit memory fuse power
cable (1) with the related positive cables (2) from
the battery cut--out switch.
11. 16 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
6. Detach the fitting (3) of the return pipe (2) for the
coolant from the cab heater radiator connected to
the underside of the coolant pump (1) and drain
off the engine coolant.
3
7. Remove the catch (2) and detach the toolbox (1).
4
8. Remove the split pins, retaining pin and front
ballast assembly (1) from the support.
5
9. Unscrew the front central and rear retaining bolts
on the front axle shaft guard, then remove the
guard (1).
25038
1
6
12. SECTION 10 -- ENGINE -- CHAPTER 1 17
87679925A -- 12 -- 2007
10. Remove the circlip (2) and move the front sleeve
(1) in the direction indicated by the arrow until it
is released from the groove on the front axle.
25039
1 2
7
11. Remove the circlip (2) and move the rear sleeve
(1) in the direction indicated by the arrow until it
is released from the groove on the drive.
25040
1
2
8
12. Remove the propeller shaft central support (1)
retaining bolts and extract the shaft together with
the support.
1
25041
9
13. 18 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
13. Remove the retaining bolts (1) of the draw pipe
(2) of the lift pump.
On the same side of the machine, on the left,
unscrew the underlying oil pipes and, if there are
clamps on them screwed onto the frame,
unscrew them to free the pipes from the frame.
-- Unscrew the nozzle oil delivery pipe on the
high--pressure pump.
-- On the power steering pump, unscrew the oil
hose delivering oil to the power steering control
valve.
-- Again on the left--hand side behind the
connection between the clutch casing and
engine, on the control valve of the gearbox (if
there is a hydraulic gearbox) or on the services
control valve, unscrew the delivery and return
pipes to the cooler and the supply pipe to the
control valve.
-- Still in the area of the latter, unscrew the second
part of the front differential lock pipe.
10
14. Remove the two metal clamps (2) and the rigid
pipe (1) for drawing oil from the transmission via
the pumps of the lift and power steering, remove
the pipe.
On the same side of the machine, on the right,
unscrew the underlying oil pipes and, if there are
clamps on them screwed onto the frame,
unscrew them to free the pipes from the frame.
-- High pressure user supply pipe, remove the pipe.
-- On the gearbox filter, remove the delivery to the
gearbox control valve and extract the pipe, then
remove the filter too.
-- Again on the gearbox filter, remove the power
steering outlet hose to the filter (in the case of the
hydraulic transmission) or remove the supply
pipe to the services control valve (in the case of
the mechanical transmission) then remove the
pipe. 11
15. Extract the plastic fasteners (2) and detach the
diesel recovery pipe (3) and delivery pipe (4) to
the diesel pump (1).
12
14. SECTION 10 -- ENGINE -- CHAPTER 1 19
87679925A -- 12 -- 2007
16. Disconnect the electrical connections (1) of the
engine main cable from the cab cable.
13
17. Disconnect all the electrical connections (1)
located on the cab main cable and connect on the
engine users.
14
18. Disconnect the two power steering oil delivery
and return hoses (1), remove the pipe.
15
19. Remove the front differential lock union (1) and
the hose (2) together with the pipe disconnected
in the operation 13.
16
15. 20 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
20. Remove the retaining clips (1) and detach the
flexible cables governing the hand throttle (5) and
pedal throttle (4).
21. Remove the retaining clip (3) and detach the
throttle control tie--rod (2) connected to the
injection pump.
17
22. Detach the clamp (1) and the cab heater delivery
pipe (2).
18
23. Take out the three exhaust silencer rear retaining
bolts (1).
19
24. Remove the clamp (1), the air filter dust ejector
pipe (2) and the four nuts (3) securing the
silencer to the exhaust manifold.
20
16. SECTION 10 -- ENGINE -- CHAPTER 1 21
87679925A -- 12 -- 2007
25. Remove the silencer (2) together with the
exhaust pipe (1).
21
26. Remove the two clips (2) for retaining to the
support (3) and the brake fluid reservoir (1).
22
27. Remove the two retaining bolts (1) and the
support (2) together with the relays (3) protecting
the system.
23
28. Remove the two retaining bolts (1) and the
support together with the fuse--holder box (2).
24
17. 22 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
29. Remove the four rear retaining bolts (1) of the
bonnet support (2).
25
30. Remove the three front retaining bolts (1) of the
bonnet support (2).
26
31. Detach the bonnet support (1).
27
32. Disconnect the clogged filter sensor, loosen the
clamps and detach the pipes on the air filter:
-- air delivery to the turbo (1), (remember also to
disconnect the pipe on the oil vapour recovery
filter that will remain connected to the delivery
pipe)
-- pneumatic braking compressor intake (2), (if
installed)
-- ejector (3) then recovery it
take out the screws (4), remove the air filter.
28
18. SECTION 10 -- ENGINE -- CHAPTER 1 23
87679925A -- 12 -- 2007
33. Loosen the air delivery retaining clamp (1) on the
turbo and extract the pipe.
29
34. Loosen the air delivery pipe clamp (1) from the
turbo to the air / air exchanger; perform the same
operation on the left--hand air supply pipe, from
the cooler to the intake manifold.
30
35. Loosen the clamp on the turbo then extract the
pipe, on the left--hand side loosen the one on the
intake manifold recovering the pipe.
31
36. Remove the coolant compensation box from the
support.
Unscrew the retaining bolts (1) on the right and
left, then remove the cooler.
32
19. 24 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
37. Remove the two retaining bolts (2) and detach
the support (3) together with the dryer filter (1)
and pipes.
1
23
33
38. Unhook the top pin (1) retaining the condenser.
34
39. Turn the steering wheel fully to the left, remove
the radiator of the condenser (1) from the same
side of the tractor.
35
40. Remove the compressor (1) as described in
section 50 without detaching pipes (2) and (3) so
as not to then have to recover, evacuate and
charge the gas in the air conditioning system.
36
20. SECTION 10 -- ENGINE -- CHAPTER 1 25
87679925A -- 12 -- 2007
41. Remove the condenser radiator (1) the dryer
filter (2) with its support and the compressor (3),
resting them alongside the right--hand rear wheel
with the associated piping.
37
42. Loosen the corresponding retaining clamps and
extract the top pipe between the radiator and the
thermostatic valve on the engine.
38
43. Loosen the retaining clamp (2) and extract the
pipe (1) joining the coolant pump to the bottom of
the radiator.
39
44. Remove the two retaining bolts (1) and the brake
piping support (2).
40
21. 26 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
45. Remove the three retaining bolts (2) and the
left--hand side guard (1) of the engine fan.
41
46. Working from the side of the starter motor (1),
remove the retaining nut (2) and the protective
cable housing (3).
42
47. Remove the retaining nut (1) and the electrical
cable (2) connected to the fuse--holder box and
the positive cable between the motor and battery
cut--out.
Disconnect all the connections of the engine main
cable (on the brake pump pressure switches, on
the brake oil cup, on the coolant temperature
sensor, engine speed, engine oil pressure, grid
heater, ........) cut the plastic clamps and remove
the metal ones, recover the electrical system.
43
48. Remove the four knobs (1) and take off the two
right-- and left--hand dashboard panels (2).
MDD2562A
1 2
44
22. SECTION 10 -- ENGINE -- CHAPTER 1 27
87679925A -- 12 -- 2007
49. Extract the differential lock pedal retaining pin (in
the case of standard machines) from the drive
shaft (1), remove the pedal and footboard (2).
25043
1
2
45
50. Remove the four plugs (1) in order to gain access
to the engine upper retaining bolts.
46
51. Using the wrench (1), remove the two nuts and
two bolts fastening the engine to the
transmission, gaining access via the four slots in
the platform (2).
47
52. Hitch the engine to the hoist with the chains (1)
anchoring it to the attachments (2) on the engine.
48
23. 28 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
53. Position a fixed stand (2) under the clutch
housing (1) near the engine attachment flanging
and apply the handbrake.
49
54. Position the movable tool for dismantling tractors
380000569 (2) with the bracket 380000500 and
adapter plate 380000844 under the engine and
place a wooden block (1) in between the points of
contact between the tool and tractor.
1
2
MODD1771A
50
55. Remove the two bolts fastening the engine to the
transmission on the tank side using the 19 mm
wrench (1) shown alongside.
51
56. Remove the remaining six retaining bolts (1) at
the bottom and side.
52
24. SECTION 10 -- ENGINE -- CHAPTER 1 29
87679925A -- 12 -- 2007
57. Separate the engine (1) from the transmission
with the tool 380000569 (2).
25050
1 2
53
58. Insert the fixed stand (1) under the ballast support
and secure the front wheels with wooden
blocks (2).
1 225056
54
59. Position a fixed stand (3) under the support of the
groove (1) of the front axle drive placing a wooden
plug (2) between the parts (3) and (1).
55
60. Fit the lifting eyelet (1) in the threading on the
support (2).
56
25. 30 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
61. Insert the hooks of the lifting chains (1) in the
eyelets shown in the figure, afterwardstensioning
the chains with the hoist.
57
62. Remove the four bolts (2) fastening the front axle
support (1) to the engine (3).
58
63. Detach the engine (2) from the front axle (3),
trying to avoid incorrect operations with the hoist
so as not to let the engine fan damage the fins of
the radiator (1), left on the axle (3).
64. Then rest the engine (2) on a platform support.
59
26. SECTION 10 -- ENGINE -- CHAPTER 1 31
87679925A -- 12 -- 2007
65. To refit the engine, proceed as follows:
ATTENTION
Use suitable tools to align the holes. NEVER USE
FINGERS OR HANDS.
-- Respect the tightening torques prescribed on
page 6.
-- Insert the three hooks of the chain in the eyelets
on the engine and, using the hoist, lift the
assembly off the platform support.
-- Position the engine on the front axle, trying to
avoid incorrect operations with the hoist so as not
to let the engine fan damage the fins of the
radiator, then join the two assemblies together
with the four retaining bolts.
-- Reposition the movable tool for dismantling
tractors 380000569 under the engine and place
a wooden block in between the point of contact
between the tool and engine.
-- With the aid of the hoist, place the engine on the
tool 380000569 and remove the lifting eyelet
previously fitted on the front of the engine.
-- Remove the fixed stand previously positioned
under the support of the groove of the drive of the
front axle and the wooden plug.
-- Remove the fixed U--bolt fitted beforehand under
the ballast support and the two wooden wedges
locking the front wheels.
-- Remove the old sealing paste from the two
surfaces between the engine and clutch casing.
-- Apply LOCTITE sealing compound on the
engine/clutch casing contact surfaces.
-- Position wooden blocks under the rear wheels,
make sure that the handbrake is fully applied and
that all fixed and mobile stands are safely
positioned.
-- The installation phase described here requires
the presence of two or three workers to use the
movable tool for dismantling tractors 380000569
to move the engine/front axle assembly close to
the clutch casing.
-- In the phase of installing the engine/front axle
assembly to the clutch casing, it is necessary to
push on the front wheels, taking great care in the
end phase of coupling over both the pipes and the
cables/electrical connections to prevent crushing
between the two bodies. During this phase, it is
moreover necessary to turn the crankshaft with
the aid of the radiator cooling fan to help the
coupling between the sleeve and the drive shaft.
-- Secure both assemblies by tightening all the bolts
locking the engine to the clutch casing.
-- Disconnect the hoist chains, remove the U--bolt
previously fitted under the clutch casing and
recover the movable tool for dismantling tractors
380000569.
-- Refit the 4 plugs on the platform and refit the
footboard and, in the case of standard machines,
refit the lock pedal.
-- Refit the two cabinets under the instrument panel
with the 4 knobs.
-- Refit the specific electric cable of the engine, bind
it with the plastic clamps and with the related
metal clamps, refit the related plastic guards on
the starter motor too.
-- Refit the fan guard on the left--hand side.
-- Refit the brake pipe support.
-- Refit the two cylinder block / radiator connecting
pipes, top and bottom, with the metal clamps.
-- Install the compressor as described in section 50
together with the pipes.
-- Refit the condenser radiator together with the
pipes and reconnect the top condenser retaining
pin.
-- Refit the dryer filter together with its support and
piping, tightening the two retaining bolts.
-- Refit the air / air cooler with the metal pipes and
sleeves, tightening them with the metal clamps.
27. 32 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
-- Refit the air filter, ejector pipe, delivery pipe to the
turbo with the pipe on the oil vapour recovery
filter, and the air brakes compressor intake pipe
(if installed), tighten the metal clamps, reconnect
the electrical system to the clogged filter sensor.
-- Refit the bonnet support, tightening the retaining
bolts.
-- Refit the support with the fuse--holder box on the
bonnet support, tightening the two retaining bolts.
-- Refit the support together with the relays
protecting the system on the bonnet support,
fitting the two retaining bolts.
-- Refit the brake fluid reservoir onto the support
and the two retaining clips.
-- Refit the silencer together with the exhaust pipe.
-- Secure the silencer to the exhaust manifold with
the four nuts and connect the air filter dust
extractor pipe to the silencer exhaust, inserting
the retaining clamp.
-- Refit the three rear retaining bolts of the exhaust
silencer.
-- Fit the cab heater delivery and return pipes and
insert the associated clamps.
-- Install the flexible cables governing the hand and
pedal throttle, inserting the retaining clips.
-- Reconnect the throttle control tie--rod to the
injection pump, inserting the retaining clip.
-- Refit the hose together with the front differential
lock pipe.
-- Reconnect the right and left steering hoses to the
front axle.
-- Reconnect all the pins of the cab main electrical
system to the users on the engine.
-- Reconnect the engine cable main connection to
the cab.
-- Reconnect the diesel recovery and delivery pipes
to the pump.
-- Position and reconnect the oil pipes (described in
operation 14.) on the right--hand side, taking care
to tighten the clamps to the frame.
-- Position and reconnect the oil pipes (described in
operation 13.) on the left--hand side, taking care
to tighten the clamps to the frame.
-- Refit the propeller shaft with its central support
and the retaining bolts.
-- Refit the front axle drive shaft guard, tightening
the front, central and rear retaining bolts.
-- Refit the front ballast together with the support
and insert the retaining pin and the split pins.
-- Refit the toolbox and the catch.
-- Refit the positive cables and the control unit
memory cable on the mechanical battery cut--out
switch.
-- Refit the battery cut--out switch on the guard on
the right--hand side of the fan, refit the guard
tightening the three retaining bolts.
-- Refill the oil from the transmission/gearbox and
the coolant in the radiator.
-- Install the bonnet as described, see section 90.
-- Reconnect the battery negative cable.
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. SECTION 10 -- ENGINE -- CHAPTER 1 33
87679925A -- 12 -- 2007
CRANKSHAFT FRONT SEAL
Renew
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks. Ensure that
no--one is in the vicinity of the load to be lifted.
To access the seal, proceed as follows:
1. Remove the bonnet (1) as described, see
section 90, and disconnect the battery negative
cable.
60
2. Remove the radiator of the condenser (1), see
section 50, without however removing the
condenser gas delivery/return pipes so as not to
recover/recharge the system refrigerant gas.
61
3. Remove radiator (1), as described in this section
on page 59.
62
30. 34 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
4. Loosen the pivot screws (2) and lock screws (1)
of the tightener (3).
63
5. Loosen the bolt (2) tensioning the belt (1) and
remove the belt.
64
6. Remove the six retaining bolts (1), the pulley (2)
governing the accessory assemblies and the
fan--alternator--coolant pump pulley (3).
65
7. Apply tool 380000665 (4) on the front tang (2) of
the crankshaft.
8. Perforate the inner seal (1) with a drill bit
(∅ 3.5 mm) through the guide holes of the tool
380000665 (4), for a depth of 5 mm.
9. Secure the tool 380000665 (4) to the seal (1) by
screwing down the screws (3) supplied.
10. Extract the seal (1) by screwing down the screw
(5).
MIF0916A
66
31. SECTION 10 -- ENGINE -- CHAPTER 1 35
87679925A -- 12 -- 2007
11. Fit the tie rod (3) of the tool 380000669 to the
outer seal (1) as shown in the figure and with the
lever (4), extract it from the front cover (2).
12. To assemble, proceed as follows:
ATTENTION
Use suitable tools to align the holes. NEVER USE
FINGERS OR HANDS. MIF0917A
67
To fit the front seal on the crankshaft, proceed as
follows:
-- Fit part (4) of tool 380000666 on the front shank
(3) of the crankshaft. Secure it with the screws (5)
and spline the new seal (6) onto it. Position part
(1) on part (4), screw down the nut (7) until the
seal (6) is completely fitted in the front cover (2).
MIF1001A
68
-- Fit the fan--alternator--coolant pump pulley, the
accessory assembly pulley and the six retaining
bolts.
-- Refit the transmission belt on the pulleys, adjust
it with the tensioning screw and lock the tightener,
tightening the two retaining and pivot screws.
-- Refit the engine radiator as described in the
operation in this section on page 59.
-- Refit the condenser radiator, see section 50.
-- Reconnect the battery negative cable and close
the bonnet.
32. 36 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
CRANKSHAFT REAR SEAL
Renew
DANGER
Lift and handle all heavy parts using suitable lifting
equipment.
Make sure that assemblies or parts are supported by
means of suitable slings and hooks. Ensure that
no--one is in the vicinity of the load to be lifted.
To access the seal, proceed as follows:
1. Remove the clutch as described in section 18.
69
2. Remove the eight screws (1) fixing the engine
flywheel (2).
70
3. Screw two pins (2) of the appropriate length into
the holes in the crankshaft (3).
Slightly extract the engine flywheel (1) so it canbe
slung and then put down in a specific wooden
container with the hoist.
MIF1116A
71
4. Apply tool 380000663 (3) on the rear shank (1) of
the crankshaft.
33. SECTION 10 -- ENGINE -- CHAPTER 1 37
87679925A -- 12 -- 2007
5. Perforate the inner seal (5) with a drill bit
(∅ 3.5 mm) through the guide holes of the tool
380000663 (3), for a depth of 5 mm.
6. Secure the tool 380000663 (3) to the seal (5) by
screwing down the screws (2) supplied.
7. Extract the seal (5) by screwing down the screw
(4).
MIF0927A
72
8. To assemble, proceed as follows:
ATTENTION
Use suitable tools to align the holes. NEVER USE
FINGERS OR HANDS.
To fit the front seal on the crankshaft, proceed as
follows:
9. Fit part (6) of tool 380000664 on the rear shank
(3) of the crankshaft. Secure it with the screws (1)
and spline the new seal (2) onto it.
Position part (5) on part (6), screw down the nut
(4) until the seal (2) is completely fitted in the
flywheel casing.
MIF1145A
73
10. With a hoist and appropriate slinging, insert the
engine flywheel (1) on the pins (2) described
above, pushing it into contact with the crankshaft
(3).
MIF1116A
74
34. 38 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
11. Manually tighten the bolts (2) retaining the
flywheel (1) to the crankshaft.
MIF1115A
75
12. Tighten the bolts (1) securing the engine flywheel
(2) in two successive stages as described on
page 6:
-- 1st phase, tightening with torque wrench to a
torque of 30 ± 5 Nm;
-- 2nd stage, angle closed 605 ± 5°.
NOTE: Angle closing is performed with tool
380001001.
MIF1146A
76
13. Install the clutch as described in section 18.
35. SECTION 10 -- ENGINE -- CHAPTER 1 39
87679925A -- 12 -- 2007
VALVE TAPPET AND ROCKER ARM
CLEARANCE
Adjustment
ATTENTION
Handle all parts carefully. Do not put your hands or
fingers between parts. Wear the prescribed safety
clothing, including goggles, gloves and safety
footwear.
1. Remove the bonnet (1) as described, see
section 90.
2. Disconnect the battery negative cable.
77
3. Remove the plastic retaining clamps, from the
cab heater water delivery--return pipes (2) and
those of the electric cables (1), moving the pipes
and cables on the compressor as described in the
figure.
78
4. Remove the retaining bolt and the front tappet
inspection cover (1) together with the cover base
seal.
79
36. 40 SECTION 10 -- ENGINE -- CHAPTER 1
87679925A -- 12 -- 2007
5. Remove the two retaining bolts (3) and thecentral
tappet inspection cover (2) together with the
engine vapour intake pipe (1) and the cover base
seal.
80
6. Remove the retaining bolt and the rear tappet
inspection cover (1) together with the cover base
seal.
81
7. After taking off the covers, adjust the clearance
between the rocker arms and valves using an
Allen wrench (1), box wrench (2)and feelergauge
(3).
The working clearance should be:
-- inlet valves = 0.25 ± 0.05 mm
-- exhaust valves = 0.50 ± 0.05 mm.
MIF1016A
82
8. Take the cylinder where the clearance is to be
adjusted into the end--of--compression phase;
the valves in the cylinder are closed, whilst those
on the symmetrical cylinder are rocking.
-- The symmetrical cylinders are 1 -- 4 and 3 -- 2.
-- FIRING ORDER 1 -- 3 -- 4 -- 2
Balancing valves of
cylinder no.
1 3 4 2
Adjust valve clearan-
ce of cylinder no.
4 2 1 3