This document is a service manual for several forage harvester models: FR480, FR550, FR650, FR780, and FR850. It contains over 20 sections that provide technical specifications, diagrams, and repair instructions for the engine, transmission, hydraulic and electrical systems, attachments, feeding, chopping, and other components of the forage harvesters. The manual is intended to assist technicians with maintenance and repairs.
New holland fr480 forage harvester service repair manualdfujsejfskekem
This service manual provides technical information for the FR480, FR550, FR650, FR780, and FR850 forage harvesters. It contains sections covering the engine, transmission, axles, hydraulics, electrical systems, attachments, feeding, chopping, ejection, and other components. The manual uses a coding system to organize information by component, type of data, and applicable product to allow technicians to easily find the information needed to service machines. Safety information is also provided.
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfusjejfskekfmsme
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains instructions, specifications, and component level details to guide qualified service personnel in maintenance and repairs. Safety notices are provided throughout to warn of hazards during service.
2017 hino 195h series truck service repair manualfujsjefjskekmme
This document provides information about repair procedures for Hino Trucks models HINO 155, 155h, 195, 195h. It includes instructions for removing and replacing components like the service plug and power control unit on the hybrid system. Safety precautions are outlined and terminology used in the manual is defined. Recommended lubricants and torque specifications for fasteners are also included.
2016 hino 195h series truck service repair manualfujsjefjskekmme
This document provides information for repair procedures on Hino trucks. It covers vehicle identification, safety precautions when working on vehicles, an introduction to the workshop manual, terminology definitions, recommended lubricants, and other relevant details. Technicians are advised to take safety measures like wearing protective equipment and blocking wheels when working on vehicles. Vehicle identification numbers and diagrams are provided to properly identify models.
2012 hino 195h series truck service repair manualfujsjefjskekmme
This document provides safety instructions and readiness guidelines for working on Hino trucks. It advises wearing protective equipment like safety glasses and removing loose clothing and jewelry before starting work. Additional guidelines include setting the parking brake and blocking the wheels, turning off the engine, and taking caution around hot or electrical components. Read and follow all warnings, cautions and instructions in the manuals carefully to prevent injury or damage.
The document provides instructions for installing an oil monitoring sensor kit that monitors engine and hydraulic oil conditions on various excavator models. It consists of 3 parts:
1) Installing additional wire harnesses and connectors inside the cab 2) Installing the wire harness outside the cab 3) Setting up the monitoring functions on the machine's display. Customers who would benefit are those concerned about preventative maintenance and oil quality. The sensor kit allows 24/7 remote monitoring of oil conditions.
Case ih farmall 95 n without cab tier 3 tractor service repair manual pin zcj...fusjejfjskekme
This document is a service manual for Farmall tractors models 75N, 85N, 95N, 105N, and 105V. It contains sections covering the tractor engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, steering, wheels, cab climate control, and electrical systems. Each section provides information on components and repair procedures for the relevant tractor systems.
Case ih axial flow 7140 stage iv combine service repair manual (pin yfg014001...ujsjfkskemmem
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions and component diagrams to assist technicians with servicing and repairing the combines.
New holland fr480 forage harvester service repair manualdfujsejfskekem
This service manual provides technical information for the FR480, FR550, FR650, FR780, and FR850 forage harvesters. It contains sections covering the engine, transmission, axles, hydraulics, electrical systems, attachments, feeding, chopping, ejection, and other components. The manual uses a coding system to organize information by component, type of data, and applicable product to allow technicians to easily find the information needed to service machines. Safety information is also provided.
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfusjejfskekfmsme
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains instructions, specifications, and component level details to guide qualified service personnel in maintenance and repairs. Safety notices are provided throughout to warn of hazards during service.
2017 hino 195h series truck service repair manualfujsjefjskekmme
This document provides information about repair procedures for Hino Trucks models HINO 155, 155h, 195, 195h. It includes instructions for removing and replacing components like the service plug and power control unit on the hybrid system. Safety precautions are outlined and terminology used in the manual is defined. Recommended lubricants and torque specifications for fasteners are also included.
2016 hino 195h series truck service repair manualfujsjefjskekmme
This document provides information for repair procedures on Hino trucks. It covers vehicle identification, safety precautions when working on vehicles, an introduction to the workshop manual, terminology definitions, recommended lubricants, and other relevant details. Technicians are advised to take safety measures like wearing protective equipment and blocking wheels when working on vehicles. Vehicle identification numbers and diagrams are provided to properly identify models.
2012 hino 195h series truck service repair manualfujsjefjskekmme
This document provides safety instructions and readiness guidelines for working on Hino trucks. It advises wearing protective equipment like safety glasses and removing loose clothing and jewelry before starting work. Additional guidelines include setting the parking brake and blocking the wheels, turning off the engine, and taking caution around hot or electrical components. Read and follow all warnings, cautions and instructions in the manuals carefully to prevent injury or damage.
The document provides instructions for installing an oil monitoring sensor kit that monitors engine and hydraulic oil conditions on various excavator models. It consists of 3 parts:
1) Installing additional wire harnesses and connectors inside the cab 2) Installing the wire harness outside the cab 3) Setting up the monitoring functions on the machine's display. Customers who would benefit are those concerned about preventative maintenance and oil quality. The sensor kit allows 24/7 remote monitoring of oil conditions.
Case ih farmall 95 n without cab tier 3 tractor service repair manual pin zcj...fusjejfjskekme
This document is a service manual for Farmall tractors models 75N, 85N, 95N, 105N, and 105V. It contains sections covering the tractor engine, clutch, transmission, four-wheel drive system, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, steering, wheels, cab climate control, and electrical systems. Each section provides information on components and repair procedures for the relevant tractor systems.
Case ih axial flow 7140 stage iv combine service repair manual (pin yfg014001...ujsjfkskemmem
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions and component diagrams to assist technicians with servicing and repairing the combines.
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfjksekkmsemm
This document is a service manual for Axial-Flow combines models 7240, 8240, and 9240 with Tier 4B engines. It contains over 200 sections organized by technical system (e.g. engine, transmission, brakes) providing specifications, diagrams and procedures for maintenance and repair.
Case ih axial flow 8240 tier 4 b (final) combine service repair manualfjjsekkfksmem
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section includes subsections for specific components.
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfujjsekskemme
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains diagrams, specifications, procedures and safety information for qualified service personnel.
Case ih axial flow 9240 tier 4 b (final) combine service repair manualfjsekksmem
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section includes subsections for specific components.
Case ih axial flow 9240 tier 4 b (final) combine service repair manualfjjskekskemmm
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains instructions, specifications, and component level details to guide qualified service personnel in maintenance and repairs. Safety notices are provided throughout to warn of hazards during service.
Case ih axial flow 8240 tier 4 b (final) combine service repair manualfjsjekskekmmme
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section provides detailed information, part numbers, and repair instructions for the various components.
Case ih axial flow 6140 stage iv combine service repair manual (pin yfg014001...fjskefkksemm
This document is a service manual for Axial-Flow combines models 5140, 6140, and 7140. It contains over 55 chapters that provide information on engine systems, transmission, axles, hydraulics, brakes, electrical systems, cab climate control, and other components. The manual includes specifications, repair and maintenance instructions, and diagrams to assist technicians in servicing the combines.
Case ih axial flow 7140 stage iv combine service repair manual (pin yfg014001...fjskefkksem
This document is a service manual for Axial-Flow combines from CNH Industrial. It contains over 55 sections covering the engine, transmission, axles, hydraulics, steering, brakes, climate control, electrical systems, and other components. The manual provides maintenance and repair information for technicians working on Axial-Flow 5140, 6140, and 7140 Stage IV combines manufactured after January 2016.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fjjskefkskem
This document is a service manual for Axial-Flow combines models 5140, 6140, and 7140. It contains over 55 chapters that provide information on engine systems, transmission, hydraulics, electrical systems, and other components. The manual instructs qualified service technicians on repair and maintenance procedures and uses special tools.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fujsekkskemm
This document is a service manual that provides information on servicing and repairing Axial-Flow combines. It includes sections on the engine, transmission, axles, hydraulics, steering, brakes, electrical systems, and climate control. Each section includes subsections that describe the components and how to service them. The table of contents lists the section and subsection numbers next to brief descriptions to help technicians quickly locate specific information in the manual.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fusjezsfkskefmsme
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions on maintenance, repair, and servicing of components with references to specific section numbers for each system.
Case ih axial flow 6140 stage iv combine service repair manual (pin yfg014001...fujsekkskemm
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions and component locations to assist technicians with servicing and repairs.
John deere 664 row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 665 r row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 666 row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 666 r row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety symbols and cautions presented throughout the text.
Caterpillar cat d350 e articulated truck (prefix 9lr) service repair manual (...fjjskkefksme
The document provides instructions for removing and installing a hoist control valve and hoist cylinder on a Caterpillar D350E articulated truck. It describes removing hoses, lines, and mounting hardware to detach the components. Safety precautions are noted regarding hot hydraulic oil. The hoist control removal process involves taking out pins and levers. Reinstallation follows the removal steps in reverse order.
Caterpillar cat d350 d articulated truck (prefix 9rf) service repair manual (...fjjskkefksme
The document provides instructions for removing and installing steering control valves, hoist control valves, and systems protection valves on D25D, D30D, and D350D articulated dump trucks. The instructions describe removing hoses and lines, draining fluids if needed, removing mounting hardware, and reversing the steps to install the valves. Detailed steps are provided for disassembling and assembling the steering control valve and hoist control valve components. Safety precautions are noted for working on air systems.
Caterpillar cat d350 d articulated truck (prefix 3aj) service repair manual (...fjjskkefksme
This document provides instructions for removing and installing the primary hydraulic pump on D25D, D30D, and D350D articulated dump trucks. It describes:
1) Removing the pump by draining fluid, removing lines and hoses, and loosening mounting bolts.
2) Disassembling the pump by removing covers, seals, rotors, vanes and other internal components.
3) Assembling the pump by installing components in reverse order, ensuring proper orientation and alignment.
More Related Content
Similar to New holland fr480 forage harvester service repair manual
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfjksekkmsemm
This document is a service manual for Axial-Flow combines models 7240, 8240, and 9240 with Tier 4B engines. It contains over 200 sections organized by technical system (e.g. engine, transmission, brakes) providing specifications, diagrams and procedures for maintenance and repair.
Case ih axial flow 8240 tier 4 b (final) combine service repair manualfjjsekkfksmem
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section includes subsections for specific components.
Case ih axial flow 7240 tier 4 b (final) combine service repair manualfujjsekskemme
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains diagrams, specifications, procedures and safety information for qualified service personnel.
Case ih axial flow 9240 tier 4 b (final) combine service repair manualfjsekksmem
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section includes subsections for specific components.
Case ih axial flow 9240 tier 4 b (final) combine service repair manualfjjskekskemmm
This service manual provides information for servicing the engines, mechanical systems, electrical systems, and other components of Axial-Flow 7240, 8240 and 9240 combines. The manual is divided into sections covering the various systems and contains instructions, specifications, and component level details to guide qualified service personnel in maintenance and repairs. Safety notices are provided throughout to warn of hazards during service.
Case ih axial flow 8240 tier 4 b (final) combine service repair manualfjsjekskekmmme
This document is a service manual for Axial-Flow 7240, 8240, and 9240 combines with Tier 4B engines. It contains sections covering the engine, main gearbox and drive, transmission, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, steering, wheels, tracks and track suspension, cab climate control, electrical systems, product feeding, threshing, separation, residue handling, and crop storage and unloading systems. Each section provides detailed information, part numbers, and repair instructions for the various components.
Case ih axial flow 6140 stage iv combine service repair manual (pin yfg014001...fjskefkksemm
This document is a service manual for Axial-Flow combines models 5140, 6140, and 7140. It contains over 55 chapters that provide information on engine systems, transmission, axles, hydraulics, brakes, electrical systems, cab climate control, and other components. The manual includes specifications, repair and maintenance instructions, and diagrams to assist technicians in servicing the combines.
Case ih axial flow 7140 stage iv combine service repair manual (pin yfg014001...fjskefkksem
This document is a service manual for Axial-Flow combines from CNH Industrial. It contains over 55 sections covering the engine, transmission, axles, hydraulics, steering, brakes, climate control, electrical systems, and other components. The manual provides maintenance and repair information for technicians working on Axial-Flow 5140, 6140, and 7140 Stage IV combines manufactured after January 2016.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fjjskefkskem
This document is a service manual for Axial-Flow combines models 5140, 6140, and 7140. It contains over 55 chapters that provide information on engine systems, transmission, hydraulics, electrical systems, and other components. The manual instructs qualified service technicians on repair and maintenance procedures and uses special tools.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fujsekkskemm
This document is a service manual that provides information on servicing and repairing Axial-Flow combines. It includes sections on the engine, transmission, axles, hydraulics, steering, brakes, electrical systems, and climate control. Each section includes subsections that describe the components and how to service them. The table of contents lists the section and subsection numbers next to brief descriptions to help technicians quickly locate specific information in the manual.
Case ih axial flow 5140 stage iv combine service repair manual (pin yfg014001...fusjezsfkskefmsme
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions on maintenance, repair, and servicing of components with references to specific section numbers for each system.
Case ih axial flow 6140 stage iv combine service repair manual (pin yfg014001...fujsekkskemm
This document is a service manual that provides maintenance and repair information for Axial-Flow combines models 5140, 6140, and 7140 with a Stage IV engine. The manual includes sections on the engine, transmission, axles, hydraulics, brakes, steering, wheels, climate control, electrical systems, product feeding, threshing, separation, residue handling, cleaning, crop storage and unloading, cab, and safety information. It provides detailed instructions and component locations to assist technicians with servicing and repairs.
Similar to New holland fr480 forage harvester service repair manual (12)
John deere 664 row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 665 r row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 666 row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety alerts and cautions throughout.
John deere 666 r row crop headers service repair manual (tm4530)fjjskkefksme
This technical manual is written for an experienced technician. It provides concise guides for various components requiring service, including repair sections telling how to repair components and operation and test sections helping to identify routine failures quickly. Information is organized into groups for the various components requiring service instruction. The manual also includes safety symbols and cautions presented throughout the text.
Caterpillar cat d350 e articulated truck (prefix 9lr) service repair manual (...fjjskkefksme
The document provides instructions for removing and installing a hoist control valve and hoist cylinder on a Caterpillar D350E articulated truck. It describes removing hoses, lines, and mounting hardware to detach the components. Safety precautions are noted regarding hot hydraulic oil. The hoist control removal process involves taking out pins and levers. Reinstallation follows the removal steps in reverse order.
Caterpillar cat d350 d articulated truck (prefix 9rf) service repair manual (...fjjskkefksme
The document provides instructions for removing and installing steering control valves, hoist control valves, and systems protection valves on D25D, D30D, and D350D articulated dump trucks. The instructions describe removing hoses and lines, draining fluids if needed, removing mounting hardware, and reversing the steps to install the valves. Detailed steps are provided for disassembling and assembling the steering control valve and hoist control valve components. Safety precautions are noted for working on air systems.
Caterpillar cat d350 d articulated truck (prefix 3aj) service repair manual (...fjjskkefksme
This document provides instructions for removing and installing the primary hydraulic pump on D25D, D30D, and D350D articulated dump trucks. It describes:
1) Removing the pump by draining fluid, removing lines and hoses, and loosening mounting bolts.
2) Disassembling the pump by removing covers, seals, rotors, vanes and other internal components.
3) Assembling the pump by installing components in reverse order, ensuring proper orientation and alignment.
Caterpillar cat d350 d articulated truck (prefix 1hk) service repair manual (...fjjskkefksme
The document provides instructions for removing and installing steering control valves, hoist control valves, and systems protection valves on D25D, D30D, and D350D articulated dump trucks. The instructions describe disconnecting hydraulic lines, removing mounting bolts, and reinstalling components in reverse order. Safety precautions are provided for working on air systems and components.
Caterpillar cat d250 e ii articulated truck (prefix 4ps) service repair manua...fjjskkefksme
This document provides instructions for disassembling and assembling the piston pump used for steering on a Caterpillar D250E II articulated truck. The disassembly process involves removing 21 individual components from the pump housing in a specific order. The assembly process reverses this, instructing technicians to install the 21 components back into the pump housing in the reverse order and noting the importance of alignment marks and original component positions. Lubricants and press tools are also listed as required for the assembly process.
Caterpillar cat d250 e articulated truck (prefix 5tn) service repair manual (...fjjskkefksme
The document provides instructions for installing, disassembling, and assembling a turbocharger for a Caterpillar 3306 engine. It includes:
1) Steps for installing the turbocharger onto the engine, including positioning gaskets and bolts.
2) Procedures for disassembling the turbocharger into its housing components using alignment marks and clamps.
3) Directions for reassembling the turbocharger housings back together in the correct alignment using clamps and torque specifications.
Caterpillar cat d250 d articulated truck (prefix 9mg) service repair manual (...fjjskkefksme
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
Caterpillar cat d250 d articulated truck (prefix 6ng) service repair manual (...fjjskkefksme
This document provides instructions for disassembling a Type I engine governor. It lists 57 steps to remove parts like the cover, springs, flyweights, housing pieces, and shutoff assembly. Tools include a governor repair fixture, retaining ring pliers, pin punch, and clevis driver. Inspect all parts for wear and replace as specified. Take care to contain fluids and properly dispose of them.
Caterpillar cat d250 b articulated dump truck (prefix 5wd) service repair man...fjjskkefksme
The document provides instructions for installing a fuel injection pump housing and governor on a caterpillar engine. It describes positioning the engine's number 1 piston at top center, installing the fuel injection pump housing and ensuring it is timed correctly to the engine using timing pins. It also details attaching the governor, applying the appropriate torque to secure components, and installing covers to complete the assembly. The instructions are intended to ensure proper timing of fuel delivery to the engine cylinders.
Caterpillar cat d44 b articulated dump truck (prefix 8sd) service repair manu...fjjskkefksme
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 engine, including:
- Removing and installing the engine oil cooler by removing mounting brackets and cleaning the tube bundles.
- Removing and installing the oil filter base by removing mounting bolts and filters, and replacing O-rings on fittings.
- Removing and installing oil bypass valves by removing housing covers and installing springs and plungers.
- Removing and installing the engine oil cooler and lines by removing elbows and coolers, cleaning tube bundles, and replacing O-rings on fittings.
- Removing and installing the aftercooler by draining coolant, removing mounting bolts and covers, and cleaning and replacing O
Caterpillar cat d35 hp articulated dump truck (prefix 3fd) service repair man...fjjskkefksme
The document provides instructions for assembling a starting motor for an articulated dump truck. It describes 22 steps for assembly, including lubricating parts, installing bushings, seals, wires, and other components in the correct positions and order. Torques are specified for tightening bolts and nuts. The final steps connect wires and install plugs to complete the assembly of the starting motor.
Caterpillar cat d35 c articulated dump truck (prefix 2gd) service repair manu...fjjskkefksme
The document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3306 engine. It describes:
1) Removing the starting motor and using a tool to find the top center position of the number 1 piston by turning the flywheel and installing a bolt.
2) Installing the fuel injection pump housing by aligning pins and ensuring proper clearance and positioning of components.
3) Installing the governor and checking valve timing before reinstalling covers.
Caterpillar cat d30 d articulated truck (prefix 9rf) service repair manual (9...fjjskkefksme
The document provides instructions for removing and installing a steering control valve, hoist control valve, and systems protection valve on D25D, D30D, and D350D articulated dump trucks. It describes disconnecting hydraulic lines and removing mounting bolts to remove the valves, then reversing the process to install them. It also gives steps to disassemble and reassemble the internal components of each valve.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
9. INTRODUCTION
Basic instructions - How to use and navigate through this Manual
FR480 Forage Cruiser WE
FR550 Forage Cruiser WE
FR650 Forage Cruiser WE
FR780 Forage Cruiser WE
FR850 Forage Cruiser WE
Technical information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery (eTim), DVD and in paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
47956024 15/02/2016
3
10. INTRODUCTION
How to use this manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number 00, 35, 55, etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
PRODUCT
Tractors
Vehicles with working arms: backhoes,
excavators, skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance
05 - Machine completion and equipment
10 - Engine
14 - Main gearbox and drive
18 - Clutch
21 - Transmission
23 - Four wheel drive system
25 - Front axle system
27 - Rear axle system
29 - Hydrostatic drive
31 - Implement power take-off
33 - Brakes and controls
35 - Hydraulic systems
36 - Pneumatic system
37 - Hitches, drawbars and implement couplings
39 - Frames and ballasting
41 - Steering
44 - Wheels
46 - Steering clutches
48 - Tracks and track suspension
50 - Cab climate control
55 - Electrical systems
56 - Grape harvester shaking
58 - Attachments/headers
60 - Product feeding
61 - Metering system
62 - Pressing - Bale formation
47956024 15/02/2016
4
11. INTRODUCTION
63 - Chemical applicators
64 - Chopping
66 - Threshing
68 - Tying/Wrapping/Twisting
69 - Bale wagons
70 - Ejection
71 - Lubrication system
72 - Separation
73 - Residue handling
74 - Cleaning
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding
78 - Spraying
79 - Planting
80 - Crop storage / Unloading
82 - Front loader and bucket
83 - Telescopic single arm
84 - Booms, dippers and buckets
86 - Dozer blade and arm
88 - Accessories
89 - Tools
90 - Platform, cab, bodywork and decals
47956024 15/02/2016
5
12. INTRODUCTION
Safety rules
FR480 Forage Cruiser WE
FR550 Forage Cruiser WE
FR650 Forage Cruiser WE
FR780 Forage Cruiser WE
FR850 Forage Cruiser WE
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47956024 15/02/2016
12
13. INTRODUCTION
Safety rules - Ecology and the environment
FR480 Forage Cruiser WE
FR550 Forage Cruiser WE
FR650 Forage Cruiser WE
FR780 Forage Cruiser WE
FR850 Forage Cruiser WE
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. NEW
HOLLAND strongly recommends that you return all used batteries to a NEW HOLLAND
dealer, who will dispose of the used batteries or recycle the used batteries properly. In
some countries, this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
47956024 15/02/2016
13
14. INTRODUCTION
Safety rules
FR480 Forage Cruiser WE
FR550 Forage Cruiser WE
FR650 Forage Cruiser WE
FR780 Forage Cruiser WE
FR850 Forage Cruiser WE
LEGAL OBLIGATIONS
This machine may be equipped with special guarding or other devices in compliance with local legislation. Some to
these require active use by the operator. Therefor, check local legislations on the usage of this machine.
ACCIDENT PREVENTION
Most accidents or injuries that occur in workshops are the result of non compliance to simple and fundamental safety
principles. For this reason, IN MOST CASES THESE ACCIDENTS CAN BE AVOIDED by applying the fundamental
safety principles, acting with the necessary caution and care.
Accidents may occur with all types of machine, regardless of how well the machine in question was designed and
built.
CAUTION
Unexpected machine movement!
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or
raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in minor or
moderate injury.
C0038A
SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND COMPONENTS - HY-
DRAULICS (EUROPEAN STANDARD EN982)
• Flexible hose assemblies must not be constructed from hoses which have been previously used as part of a hose
assembly.
• Do not weld hydraulic pipes: when flexible hoses or piping are damaged, replace them immediately.
• It is forbidden to modify a hydraulic accumulator by machining, welding or any other way.
• Before removing hydraulic accumulators for servicing, the liquid pressure in the accumulators must be reduced to
zero.
• Pressure check on hydraulic accumulators must be carried out by a method recommended by the accumulator
manufacturer.
• Take care not to exceed the maximum allowed pressure of the accumulator. After any check or adjustment, check
for leakages or gas in the hoses or tubes.
SAFETY RULES
General guidelines
• Carefully follow specified repair and maintenance procedures.
• When appropriate, use P.P.E (Personal Protective Equipment)
• Do not wear rings, wristwatches, jewellery, unbuttoned or loose articles of clothing such as: ties, torn clothing,
scarves, open jackets or shirts with open zips that may remain entangled in moving parts. It is advised to wear
approved safety clothing, e.g.: non-slip footwear, gloves, safety goggles, helmets, etc.
47956024 15/02/2016
14
15. INTRODUCTION
• Do not carry out repair operations with someone sitting in the driver's seat, unless the person is a trained technician
who is assisting with the operation in question.
• Do not operate the machine or use any of the implements from different positions, other than the driver's seat.
• Do not carry out operations on the machine with the engine running, unless specifically indicated.
• Bring all hydraulic cylinders to the home positions (down, retracted, etc.) before engine shut down.
• Stop the engine and check that the hydraulic circuits are pressure-free before removing caps, covers, valves, etc.
• All repair and maintenance operations must be carried out using extreme care and attention.
• Service steps and platforms used in the workshop or elsewhere should be built according to the applicable stan-
dards and legislation.
• Disconnect the Power Take-Off (PTO) and label the controls to indicate that the machine is being serviced.
• Brakes are inoperative when manually released for repair or maintenance purposes. Use blocks or similar devices
to secure the machine in these conditions.
• Only use specified towing points for towing the machine. Connect parts carefully. Make sure that all pins and/or
locks are secured in position before applying traction. Never remain near the towing bars, cables or chains that are
operating under load.
• When loading or unloading the machine from the trailer (or other means of transport), select a flat area capable of
sustaining the trailer or truck wheels. Firmly secure the machine to the truck or trailer and lock the wheels in the
position used by the carrier.
• Electric heaters, battery-chargers and similar equipment must only be powered by auxiliary power supplies with
efficient ground insulation to avoid electrical shock hazards.
• Always use suitable hoisting or lifting devices when raising or moving heavy parts.
• Keep bystanders away.
• Never use gasoline, diesel oil or other inflammable liquids as cleaning agents. Use non-inflammable, non toxic
commercially available solvents.
• Wear safety goggles with side guards when cleaning parts with compressed air.
• Never use open flames for lighting when working on the machine or checking for leaks.
• When carrying out checks with the engine running, request the assistance of an operator in the driver's seat. The
operator must maintain visual contact with the service technician at all times.
• If operating outside the workshop, position the machine on a flat surface and lock in position. If working on a slope,
lock the machine in position. Move to a flat area as soon as is safely possible.
• Maintenance and repair operations must be carried out in a clean and dry area. Clean up any water or oil spillage
immediately.
• Do not create piles of oil or grease-soaked rags as they represent a serious fire hazard. Always store rags in a
closed metal container.
• Before engaging the machine, make sure that there are no persons within the machine or implement range of action.
• Empty your pockets of all objects that may fall accidentally unobserved into the machine inner compartments.
• When metal parts are sticking out, use protective goggles or goggles with side guards, helmets, special footwear
and gloves.
• When welding, use protective safety devices: tinted safety goggles, helmets, special overalls, gloves and footwear.
All persons present in the area where welding is taking place must wear tinted goggles. NEVER LOOK DIRECTLY
AT THE WELDING ARC WITHOUT SUITABLE EYE PROTECTION.
47956024 15/02/2016
15
16. INTRODUCTION
Machine start-up.
• Never run the engine in confined spaces that are not equipped with adequate ventilation for exhaust gas extraction.
• Never place the head, body, limbs, feet, hands or fingers near rotating and moving parts.
Hydraulic systems and fuel injection systems
• A liquid leaking from a tiny hole may be almost invisible but, at the same time, be powerful enough to penetrate
the skin. Therefore, NEVER USE HANDS TO CHECK FOR LEAKS but use a piece of cardboard or paper for this
purpose. If any liquid penetrates skin tissue, call for medical aid immediately. Failure to treat this condition with
correct medical procedure may result in serious infection or death.
• In order to check the pressure in the system use suitable instruments.
Wheels and tires
• Make sure that the tires are correctly inflated at the pressure specified by the manufacturer. Periodically check the
rims and tires for damage.
• Stand away from (at the side of) the tire when checking inflation pressure.
• Do not use parts of recovered wheels as incorrect welding brazing or heating may weaken and eventually cause
damage to the wheel.
• Never cut or weld a rim mounted with an inflated tire.
• Deflate the tire before removing any objects that may be jammed in the tire tread.
• Never inflate tires using inflammable gases, as this may result in explosions and injury to bystanders.
Removal and installation
• Lift and handle all heavy parts using suitable hoisting equipment. Make sure that parts are sustained by appropriate
hooks and slings. Use the hoisting eyebolts for lifting operations. Extra care should be taken if persons are present
near the load to be lifted.
• Handle all parts carefully. Do not put your hands or fingers between parts. Wear suitable safety clothing - safety
goggles, gloves and shoes.
• Avoid twisting chains or metal cables. Always wear safety gloves when handling cables or chains.
• Damaged or bent chains or cables are unreliable. Do not use them for lifting or towing. Always use suitable pro-
tective gloves when handling chains or cables.
• Chains should always be safely secured. Make sure that the hitch-up point is capable of sustaining the load in
question. Keep the area near the hitch-up point, chains or cables free of all bystanders.
• Metal cables tend to fray with repeated use. Always use suitable protective devices (gloves, goggles, etc.) when
handling cables.
47956024 15/02/2016
16
18. Engine - Engine and crankcase
5. Remove the rear shield.
• Support the rear shield (2). Ask the assistance of a
second person or use a suitable lifting device.
• Lift up the bottom clip from the gas strut (3), then
remove the gas strut (3) from the pivot bolt.
• Remove the hardware (1).
• Remove the rear shield (2).
ZEIL15FR00085AA 2
6. Remove the hardware (4) (six in total) and remove the
top rear shield (5).
ZEIL15FR00086AA 3
Discharge the air-conditioning circuit
7. Discharge the air-conditioning circuit. See chapter “Air
Conditioning” in the service manual.
34788-300 4
47956024 15/02/2016
10.1 [10.001] / 4
19. Engine - Engine and crankcase
Drain Fluids
8. Drain the hydraulic oil reservoir.
ZEIL15FR00090AA 5
9. Drain the engine coolant:
• Engine coolant radiator
• Engine coolant intake. Close the tap, remove the
hose, drain coolant, open the tap and drain fluid.
• Engine coolant outlet. Close the tap, remove the
hose, drain coolant, open the tap and drain fluid.
NOTE: Still some coolant in the tubes.
ZEIL15FR00088AA 6
ZEIL15FR00089AA 7
Wiring harnesses
10. On the left-hand side of the machine, remove all the
straps and disconnect all the connectors of the two
wiring harness branches (see arrows) going down
of the wiring harness (6) and lay the wiring harness
branches on top of the roof assembly. See Wiring
harnesses - Overview (55.100) in the service man-
ual.
NOTE: Remove the air filter clogging sensor and the main
gearbox rpm sensor to prevent damage.
ZEIL15FR00198AA 8
47956024 15/02/2016
10.1 [10.001] / 5
20. Engine - Engine and crankcase
11. Remove all the straps and disconnect all the connec-
tors of the wiring harness branch (see arrow) going
down of the wiring harness (6) and lay the wiring har-
ness branch on top of the roof assembly. See the lo-
cation diagram in the service manual.
ZEIL15FR00120AA 9
12. On the left hand side of the machine, remove all the
straps and disconnect all the connectors of the wiring
harness branch (see arrow) going down of the wiring
harness (6) and lay the wiring harness branch on top
of the roof assembly. See the location diagram in the
service manual.
ZEIL15FR00121AA 10
13. On the right-hand side of the machine, disconnect the
connector (7A).
ZEIL15FR00132AA 11
14. Disconnect the ground cable (8) from the engine.
15. Disconnect the positive lead (9A) from the starter mo-
tor.
ZEIL15FR00148AA 12
47956024 15/02/2016
10.1 [10.001] / 6
21. Engine - Engine and crankcase
Roof assembly
16. Remove the hardware (10) (fourteen in total) and the
cooling group cover plate (12).
17. Disconnect the hoses (11) from the engine coolant
reservoir.
ZEIL15FR00091AA 13
18. Remove the hose (14) from the engine coolant intake
tube.
19. Disconnect the Diesel Exhaust Fluid (DEF)/Ad-
Blue® injector coolant lines (15A) and (15B). See
also Figure 15.
20. Remove the NOx sensor (13) from the exhaust.
21. Remove the temperature sensor (16).
22. Remove the clamp (17).
ZEIL15FR00092AA 14
ZEIL15FR00093AA 15
23. Disconnect the hose (18) from the coolant tube at the
point indicated by the arrow.
ZEIL15FR00094AA 16
47956024 15/02/2016
10.1 [10.001] / 7
22. Engine - Engine and crankcase
24. On the left-hand side of the machine, disconnect the
DEF/AdBlue® feed line from the supply module.
NOTE: Have a suitable container ready and use the appro-
priate plugs on the DEF/AdBlue® supply module and the
DEF/AdBlue® feed line (19). Clean up any DEF/AdBlue®
spill immediately.
25. Disconnect the DEF/AdBlue® coolant line (20).
26. Disconnect the DEF/AdBlue® coolant lines (15C) and
(15D) from the heater valve.
ZEIL15FR00102AA 17
27. On the left-hand side of the machine, remove the
hardware (21) and carefully pull the DEF/AdBlue®
coolant lines and the DEF/AdBlue® feed line (15)
through the hole. See arrow Figure 17.
ZEIL15FR00101AA 18
28. Loosen the clamps (22) of the rubber coupler (24) and
slide the rubber coupler (24) on the air intake tube
(23).
ZEIL15FR00196AA 19
29. Loosen the clamp (25) and remove the breather tube
(26) rubber coupler from the air intake tube (23).
30. Loosen the clamp (27) and remove the rubber elbow
coupler (28) from the air intake tube (23).
ZEIL15FR00191AA 20
47956024 15/02/2016
10.1 [10.001] / 8
23. Engine - Engine and crankcase
31. Support the roof assembly with a suitable lifting de-
vice. Use the lifting eyes near the front hinges of the
side shieldings, and use the spout support as shown.
ZEIL15FR00116AA 21
32. On the left-hand side of the machine, remove the
hardware (29).
ZEIL15FR00117AA 22
33. Remove the hardware (31).
ZEIL15FR00198AA 23
34. On the right-hand side of the machine, remove the
hardware (30) and the hardware (31).
ZEIL15FR00118AA 24
47956024 15/02/2016
10.1 [10.001] / 9
24. Engine - Engine and crankcase
35. On the right-hand side of the rear frame, remove the
hardware (32).
ZEIL15FR00121AA 25
36. On the left-hand side of the rear frame remove the
hardware (32).
ZEIL15FR00120AA 26
37. Remove the hardware (33).
ZEIL15FR00119AA 27
38. Make sure nothing remains connected to the roof as-
sembly. Remove the roof assembly.
NOTE: Make sure that the chains are set in such a way
that the roof assembly, when lifted, is properly balanced.
NOTE: Make sure nothing remains connected when you
lift up the roof assembly.
ZEIL15FR00116AA 28
47956024 15/02/2016
10.1 [10.001] / 10
25. Engine - Engine and crankcase
Air and coolant tubes
39. Loosen the clamp (34) of the cooling group air intake
tube (35).
ZEIL15FR00138AA 29
40. Loosen the clamp (37).
41. Remove the clamp hardware (36). Remove the air
intake tube (35).
ZEIL15FR00137AA 30
42. Loosen the clamp (39) of the engine air intake tube
(38).
43. On the engine, loosen the clamp (39) of the engine
air intake tube (38) at the engine air intake piece (not
shown).
44. Remove the clamp hardware (40).
45. Remove the pig tail (41) from the engine air intake
tube (38).
ZEIL15FR00140AA 31
46. Loosen the hose clamp (42) of the engine coolant out-
let tube (43).
47. Remove the clamp hardware (44) of the engine
coolant outlet tube (43).
ZEIL15FR00144AA 32
47956024 15/02/2016
10.1 [10.001] / 11
26. Engine - Engine and crankcase
48. Loosen the hose clamp (46) of the engine coolant out-
let tube (43).
49. Remove the clamp hardware (45) and remove the en-
gine coolant outlet tube (43).
NOTE: The tube is full of engine coolant.
ZEIL15FR00145AA 33
50. Loosen the hose clamp (47).
51. Remove the clamps (48) and remove the breather
tube (26).
ZEIL15FR00139AA 34
52. Loosen the hose clamp (49) of the engine coolant inlet
tube (50).
53. Remove the clamp hardware (51).
ZEIL15FR00142AA 35
54. Loosen the hose clamp (52).
55. Remove the clamp hardware (51) and remove the en-
gine coolant inlet tube (50).
ZEIL15FR00141AA 36
47956024 15/02/2016
10.1 [10.001] / 12
27. Engine - Engine and crankcase
Cooling fan
56. On the fan support, remove the hardware (54) of the
oil filter (53). Lay the oil filter (53) down without re-
moving the hoses.
ZEIL15FR00126AA 37
57. Remove the hardware (56) of the support (57).
58. Remove the clamp hardware (55).
ZEIL15FR00127AA 38
59. On the left-hand side of the machine, under the main
gearbox clutch shaft, remove the hardware (56) and
the support (57).
ZEIL15FR00128AA 39
60. Release the tension of the fan drive belt tensioner
(62). Remove the fan drive belt (63).
61. Disconnect the hose (60) and the hose (61).
62. Remove the clamps (55).
63. Remove the tube (58) and the tube (59). See also the
arrows in Figure 41.
ZEIL15FR00125AA 40
47956024 15/02/2016
10.1 [10.001] / 13
28. Engine - Engine and crankcase
64. Support the fan (65). Use a suitable lifting device.
65. Remove the hardware (64) and remove the fan (65)
from the machine.
ZEIL15FR00129AA 41
Hydraulics
66. Disconnect the connectors (7A), (7B), (7C), (7D),
(7E), (7F) and (7G) of the wire harness (7). See also
Figure 45.
NOTE: Connectors (7B) and (7E) are connected to the
pressure sensors who can only be found on machines with
variable displacement hydro motor. These machines have
a maximum road speed of 40 km/h.
ZEIL15FR00134AA 42
67. Remove the hose (69), the hose (71), the hose (70),
the hose (72) and the hose (73).
ZEIL15FR00136AA 43
68. Remove the hose (74), the hose (76) and the hose
(75).
ZEIL15FR00135AA 44
47956024 15/02/2016
10.1 [10.001] / 14
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Engine - Engine and crankcase
69. Remove the hose (66), the hose (67), and the hose
(68).
ZEIL15FR00133AA 45
70. Remove the hose (77), the hose (81), the hose (78),
the hose (79) and the hose (80).
ZEIL15FR00132AA 46
71. Remove the clamp hardware (82). Disconnect the
tube (83).
ZEIL15FR00146AA 47
72. Remove the clamp hardware (82). Remove the tube
(83).
ZEIL15FR00147AA 48
47956024 15/02/2016
10.1 [10.001] / 15
31. Engine - Engine and crankcase
Rear Frame
73. On the rear right-hand side of the machine. Remove
the hardware (84).
ZEIL15FR00154AZ 49
74. On the rear right-hand side of the machine. Remove
the hardware (84).
ZEIL15FR00155AA 50
75. On the rear right-hand side light cover (86). Remove
the plastic rivet (85).
ZEIL15FR00156AA 51
76. Remove the hardware (87) and the plastic rivets (85).
77. Remove the right-hand side light cover (86). See Fig-
ure 51.
ZEIL15FR00157AA 52
47956024 15/02/2016
10.1 [10.001] / 16
32. Engine - Engine and crankcase
78. Ask assistance of a second person or use a suitable
lifting device to support the rear frame (88).
79. Remove the hardware (89).
ZEIL15FR00158AA 53
80. On the left-hand side of the rear frame (88). Remove
the hardware (89) and remove the rear frame (88).
ZEIL15FR00159AA 54
Engine supports, fuel and air-conditioning lines
81. Loosen the hose clamp (27) and remove the rubber
elbow coupler (28).
ZEIL15FR00149AA 55
82. Support the engine on all three points shown. Use a
suitable lifting device.
NOTE: Make sure that the chains are set in such a way
that the engine, when lifted, is properly balanced. It could
be difficult to remove the engine, if not balanced properly.
ZEIL15FR00197AA 56
47956024 15/02/2016
10.1 [10.001] / 17
33. Engine - Engine and crankcase
83. On the right-hand side of the machine, remove the
hardware (90).
ZEIL15FR00150AA 57
84. Remove the hardware (90).
ZEIL15FR00152AA 58
85. On the left-hand side of the machine, remove the
hardware (90).
ZEIL15FR00151AA 59
86. Remove the clamp hardware (91).
87. Remove the hardware (90).
ZEIL15FR00153AA 60
47956024 15/02/2016
10.1 [10.001] / 18