This document is a service manual for Boomer compact tractors models 3040 CVT, 3045 CVT, and 3050 CVT. It contains sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, cab climate control, electrical systems, and the platform, cab, bodywork, and decals. Safety precautions are provided to ensure personal safety when operating or servicing the equipment.
New holland boomer 3050 cvt compact tractor service repair manualfujdjjskekwmem
This document is a service manual for Boomer 3040, 3045, and 3050 CVT compact tractors. It provides specifications and maintenance instructions for the engine, transmission, drivetrain, brakes, hydraulics, steering, climate control, electrical systems, cab, and decals. The manual includes torque specifications, component locations, removal and installation procedures, and troubleshooting information.
New holland boomer 25 compact tractor service repair manualujfjjkskkmdme
This service manual provides technical information for servicing the Boomer 20 and 25 compact tractors. It includes sections on the engine, transmission, axles, brakes, hydraulics, hitches, steering, wheels, electrical systems, and operator platform. The manual should be used along with the operator's manual and only by qualified dealership personnel when performing repairs or maintenance according to the instructions and using recommended tools.
Case 1150 m tier 4b (final) crawler dozer service repair manual instant downl...ufsjejfsekeme
This document provides instructions for removing the engine from a 1150M dozer. It outlines 24 steps to disconnect all electrical connections, hoses, lines and mounts. This includes removing the air cleaner, turbocharger pipe, starter, alternator, radiator and other components. Proper lifting equipment is required as the engine weighs approximately 635 kg.
Case 586 h tier 4b (final) rough terrain forklift service repair manualfujsekwsxksmem
This document provides service instructions for removing the engine and crankcase from a 586H or 588H rough terrain forklift. The steps include draining fluids, removing covers, disconnecting hoses and electrical connections, and using lifting equipment to remove the heavy engine components. Precautions are given to relieve pressure before disconnecting lines and to use caution when handling heavy parts.
New holland d125 c stage iiib crawler dozer service repair manual (pin nfdc12...ujfdjjskkmsme
This service manual section provides instructions for removing the engine from a D125C crawler dozer. Key steps include disconnecting electrical connections, hoses, and pipes; removing the air cleaner assembly, turbocharger pipe, and cooling package; and then removing mounting bolts to separate the engine from the vehicle. Proper disconnection of all components is emphasized for safety.
Case 1150 m tier 4b (final) crawler dozer service repair manual (pin ngc10510...fujsekkskemm
This document is a service manual for 1150M Crawler Dozers from Case Construction. It provides part numbers, product links to engines, and a detailed table of contents that lists all systems of the machine and subsections within each system covered in the manual. Safety information is also provided at the beginning regarding qualifications and procedures for servicing the equipment.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujjdfjkksekmem
This document provides an overview of safety information and guidelines for Patriot® 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
Case 1650 m tier 4b (final) crawler dozer service repair manual (pin ngc10700...fusfejskekem
This document provides service and repair information for various components of a Case 1650M crawler dozer, including the engine, hydrostatic drive, brakes and controls, hydraulic systems, tracks and suspension, cab climate control, electrical systems, dozer blade and arm, tools, and other components. It includes exploded diagrams, specifications, procedures, and fault codes. The document is the service manual for the 1650M dozer in various configurations.
New holland boomer 3050 cvt compact tractor service repair manualfujdjjskekwmem
This document is a service manual for Boomer 3040, 3045, and 3050 CVT compact tractors. It provides specifications and maintenance instructions for the engine, transmission, drivetrain, brakes, hydraulics, steering, climate control, electrical systems, cab, and decals. The manual includes torque specifications, component locations, removal and installation procedures, and troubleshooting information.
New holland boomer 25 compact tractor service repair manualujfjjkskkmdme
This service manual provides technical information for servicing the Boomer 20 and 25 compact tractors. It includes sections on the engine, transmission, axles, brakes, hydraulics, hitches, steering, wheels, electrical systems, and operator platform. The manual should be used along with the operator's manual and only by qualified dealership personnel when performing repairs or maintenance according to the instructions and using recommended tools.
Case 1150 m tier 4b (final) crawler dozer service repair manual instant downl...ufsjejfsekeme
This document provides instructions for removing the engine from a 1150M dozer. It outlines 24 steps to disconnect all electrical connections, hoses, lines and mounts. This includes removing the air cleaner, turbocharger pipe, starter, alternator, radiator and other components. Proper lifting equipment is required as the engine weighs approximately 635 kg.
Case 586 h tier 4b (final) rough terrain forklift service repair manualfujsekwsxksmem
This document provides service instructions for removing the engine and crankcase from a 586H or 588H rough terrain forklift. The steps include draining fluids, removing covers, disconnecting hoses and electrical connections, and using lifting equipment to remove the heavy engine components. Precautions are given to relieve pressure before disconnecting lines and to use caution when handling heavy parts.
New holland d125 c stage iiib crawler dozer service repair manual (pin nfdc12...ujfdjjskkmsme
This service manual section provides instructions for removing the engine from a D125C crawler dozer. Key steps include disconnecting electrical connections, hoses, and pipes; removing the air cleaner assembly, turbocharger pipe, and cooling package; and then removing mounting bolts to separate the engine from the vehicle. Proper disconnection of all components is emphasized for safety.
Case 1150 m tier 4b (final) crawler dozer service repair manual (pin ngc10510...fujsekkskemm
This document is a service manual for 1150M Crawler Dozers from Case Construction. It provides part numbers, product links to engines, and a detailed table of contents that lists all systems of the machine and subsections within each system covered in the manual. Safety information is also provided at the beginning regarding qualifications and procedures for servicing the equipment.
Case ih patriot 3340 tier 4 b (final) sprayer service repair manual (pin ygt0...fujjdfjkksekmem
This document provides an overview of safety information and guidelines for Patriot® 3240 and 3340 sprayers. It emphasizes the importance of following all safety messages and warnings to avoid potential injury or death. A "Do Not Operate" tag should be attached whenever service is required to clearly indicate that the machine should not be used until repairs are complete. Personal protective equipment should always be worn when operating or servicing agricultural equipment.
Case 1650 m tier 4b (final) crawler dozer service repair manual (pin ngc10700...fusfejskekem
This document provides service and repair information for various components of a Case 1650M crawler dozer, including the engine, hydrostatic drive, brakes and controls, hydraulic systems, tracks and suspension, cab climate control, electrical systems, dozer blade and arm, tools, and other components. It includes exploded diagrams, specifications, procedures, and fault codes. The document is the service manual for the 1650M dozer in various configurations.
New holland tt75 4 wd tractor service repair manualfujsefkksekfm
This document is a service manual for tractor models TT55, TT65, and TT75. It contains safety information and instructions for servicing various tractor systems, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, and electrical systems. The manual provides part numbers and diagrams to aid technicians in maintenance and repair. Safety is emphasized throughout, with warnings to take proper precautions such as shutting off the engine before servicing and wearing protective equipment.
New holland ts130 a tractor service repair manualfujsefkksekfm
This document is a chapter from a service manual for New Holland TS-A Plus and TS-A Delta series tractors. It provides instructions for separating the front axle and front support from the engine. The summary includes torque specifications for fasteners, a list of any special tools required, and a high-level overview of the separation procedure. Safety information is also provided at the beginning regarding general repair procedures.
New holland tk4030 v tractor service repair manualfujsefkksekfm
This service manual provides maintenance and repair instructions for various tractor models including the TK4020F, TK4040, and TK4060. The manual includes sections on the engine, clutch, transmission, rear axle, power take-off, brakes, hydraulics, steering, tracks, electrical systems, and cab/body. The document provides detailed procedures and specifications for removing and servicing components of the tractors.
New holland tk80 a tractor service repair manualfujsefkksekfm
This document is a repair manual for tractor models TK75VA, TK80A, TK80MA, TK90A, TK90MA, and TK100A. It contains sections covering the engine, clutch, transmissions, rear mechanical drive, mechanical power take-off, braking system, hydraulic systems, steering clutches, suspension and tracks, electrical system, and general information. The general information section provides instructions on maintenance and repair, safety precautions, lubricants, and emissions warranties. It is a comprehensive manual for servicing and repairing the listed tractor models.
New holland td80 tractor service repair manualfujsefkksekfm
This document is a service manual for TD60-TD95 straddle mount model tractors. It contains sections on general information, the engine system, clutches, mechanical transmission, and other systems. Each section provides specifications, views, removal and installation instructions, and troubleshooting information for the components covered.
New holland t6070 tractor service repair manualfujsefkksekfm
The document provides repair and service information for tractor models TS100A, TS110A, TS115A, TS125A, TS130A, TS135A, T6010, T6020, T6030, T6050, and T6070. It contains sections on general safety procedures, product identification, specifications, dimensions, and minimum hardware tightening torques. A new page is included that provides updated controller identification codes and the new location of the diagnostic connector for the T6000 series tractors.
New holland t9.700 stage iv tractor service repair manualfujsefkksekfm
This document is a service manual for various tractor models in the T9 series from CNH Industrial. It provides an overview and table of contents for the manual, which is organized by major vehicle systems. The manual covers the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. It aims to support maintenance and repair of these tractors.
New holland t8.390 tractor service repair manualfujsefkksekfm
This document is a service manual for CNH America LLC tractor models T8.275, T8.300, T8.330, T8.360, T8.390, and T8.420. The manual contains sections on the engine, power coupling, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, pneumatic system, hitches and implements, steering, cab climate control, electrical systems, platform and cab, and safety instructions. Each section provides detailed information, specifications, and repair procedures for components and systems of the tractors.
New holland t8.350 continuously variable transmission (cvt) tractor service r...fujsefkksekfm
The document is a service manual that provides maintenance instructions for engine components of various tractor models. It includes sections on the engine and crankcase, cylinder heads, air cleaners and lines, fuel filters, fuel tanks, fuel injection system, engine lubrication system, aftercooler, engine cooling system, fan and drive, and selective catalytic reduction exhaust treatment. Each section provides detailed instructions, specifications, and diagrams for servicing the corresponding component.
New holland t8.320 continuously variable transmission (cvt) tractor service r...fujsefkksekfm
This document is a service manual for CNH Industrial tractor models T8.320 through T8.435, including SmartTrax versions. The manual contains over 50 sections that provide information on repairing and maintaining the engine, transmission, axles, hydraulics, electrical systems, cab climate control, and other components of the tractors. Each section includes detailed technical specifications, diagrams, and repair procedures.
New holland t8.275 tractor service repair manualfujsefkksekfm
This service manual provides information for servicing the engines in T8 tractor models T8.275, T8.300, T8.330, T8.360, and T8.390. The manual covers systems such as the engine and crankcase, cylinder heads, fuel system, cooling system, and electrical systems. It provides specifications, maintenance procedures, and troubleshooting information for servicing these models.
New holland t7.170 auto command tractor service repair manualfujsefkksekfm
The document is a service manual that provides technical specifications, descriptions of functionality, and troubleshooting information for the hydraulic, pneumatic, electrical, and electronic systems of various tractor models. It includes sections that describe the primary and secondary hydraulic power systems, hydraulic control systems, pneumatic systems, electrical power systems, electronic systems, and fault codes. The primary hydraulic power system section provides specifications for the hydraulic pump and charge pump, as well as descriptions of how the primary hydraulic system functions statically for different tractor models.
New holland t6.140 auto command tractor service repair manualfujsefkksekfm
This section provides technical specifications and service procedures for the engine and crankcase, including torque specifications for connecting the engine, instructions for disconnecting engine components for the T6.155-T6.175 models, and procedures for reconnecting and removing the engine on the T6.155.
New holland t4.110 v tractor service repair manualfujsefkksekfm
This document is a service manual that provides technical specifications and repair/maintenance instructions for various tractor models and components. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front axle system, and other components. The manual lists the applicable engine for each tractor model and market. It also provides an overview of the contents and organization of the manual.
New holland t4.110 n tractor service repair manualfujsefkksekfm
This document is a service manual that provides specifications and repair/maintenance procedures for various tractor models and components. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front axle system, and other components. The manual lists the applicable engine for each tractor model and market. It also includes an index of contents to guide users to the relevant sections for different components.
New holland t4.95 f tractor service repair manualfujsefkksekfm
This document is a service manual for T4.75F, T4.85F, T4.95F, and T4.105F tractor models and their LP variants. It contains sections covering the engine, transmission, axles, hydraulics, hitches, steering, wheels, climate control, and electrical systems. Each section includes subsections that provide information on specific components and their repair or service. The manual also lists the engine type for each tractor model and market.
New holland ls185.b skid steer loader service repair manualfujsefkksekfm
The document is a workshop manual that provides technical information for repairing and servicing components of excavator models LS180.B, LS185.B, and LS190.B. It contains sections on the machine's distribution systems, power production, power train, travel, body and structure, and working arm. The primary hydraulic power system chapter provides specifications, diagrams, maintenance procedures, and troubleshooting information for components of the hydraulic system like the hydraulic pump, relief valve, reservoir, and oil filter. Procedures include cleaning, testing, disassembly, inspection, assembly, removal and installation of system components.
New holland c238 200 series compact track loader service repair manualfujsefkksekfm
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders, covering models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. The manual contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and PTO systems, transmissions, axles, brakes, steering, frames, cabs, user controls, positioning, tool attachment, hitching, digging and landscaping functions. Safety precautions and general specifications such as torque values are provided at the beginning.
This document is a service manual that provides safety and technical information for maintaining Command vertical crankshaft engines, models CV11-16, CV460-465, and CV490-495. The manual contains 11 sections covering topics such as safety, troubleshooting, air and fuel systems, electrical systems, disassembly, inspection, and reassembly. The introduction section emphasizes important safety precautions and provides information on identifying engine models. It also recommends using high-quality detergent oil and unleaded gasoline as fuel.
Hyster k005 (h4.00 xm 5 europe) forklift service repair manualfujsefkksekfm
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The hood repair section includes adjusting the hood latch and striker for proper operator restraint. Radiator repair involves draining coolant before removing hoses and the radiator from the lift truck.
New holland tt75 4 wd tractor service repair manualfujsefkksekfm
This document is a service manual for tractor models TT55, TT65, and TT75. It contains safety information and instructions for servicing various tractor systems, including the engine, transmission, axles, brakes, hydraulics, steering, wheels, and electrical systems. The manual provides part numbers and diagrams to aid technicians in maintenance and repair. Safety is emphasized throughout, with warnings to take proper precautions such as shutting off the engine before servicing and wearing protective equipment.
New holland ts130 a tractor service repair manualfujsefkksekfm
This document is a chapter from a service manual for New Holland TS-A Plus and TS-A Delta series tractors. It provides instructions for separating the front axle and front support from the engine. The summary includes torque specifications for fasteners, a list of any special tools required, and a high-level overview of the separation procedure. Safety information is also provided at the beginning regarding general repair procedures.
New holland tk4030 v tractor service repair manualfujsefkksekfm
This service manual provides maintenance and repair instructions for various tractor models including the TK4020F, TK4040, and TK4060. The manual includes sections on the engine, clutch, transmission, rear axle, power take-off, brakes, hydraulics, steering, tracks, electrical systems, and cab/body. The document provides detailed procedures and specifications for removing and servicing components of the tractors.
New holland tk80 a tractor service repair manualfujsefkksekfm
This document is a repair manual for tractor models TK75VA, TK80A, TK80MA, TK90A, TK90MA, and TK100A. It contains sections covering the engine, clutch, transmissions, rear mechanical drive, mechanical power take-off, braking system, hydraulic systems, steering clutches, suspension and tracks, electrical system, and general information. The general information section provides instructions on maintenance and repair, safety precautions, lubricants, and emissions warranties. It is a comprehensive manual for servicing and repairing the listed tractor models.
New holland td80 tractor service repair manualfujsefkksekfm
This document is a service manual for TD60-TD95 straddle mount model tractors. It contains sections on general information, the engine system, clutches, mechanical transmission, and other systems. Each section provides specifications, views, removal and installation instructions, and troubleshooting information for the components covered.
New holland t6070 tractor service repair manualfujsefkksekfm
The document provides repair and service information for tractor models TS100A, TS110A, TS115A, TS125A, TS130A, TS135A, T6010, T6020, T6030, T6050, and T6070. It contains sections on general safety procedures, product identification, specifications, dimensions, and minimum hardware tightening torques. A new page is included that provides updated controller identification codes and the new location of the diagnostic connector for the T6000 series tractors.
New holland t9.700 stage iv tractor service repair manualfujsefkksekfm
This document is a service manual for various tractor models in the T9 series from CNH Industrial. It provides an overview and table of contents for the manual, which is organized by major vehicle systems. The manual covers the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. It aims to support maintenance and repair of these tractors.
New holland t8.390 tractor service repair manualfujsefkksekfm
This document is a service manual for CNH America LLC tractor models T8.275, T8.300, T8.330, T8.360, T8.390, and T8.420. The manual contains sections on the engine, power coupling, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, pneumatic system, hitches and implements, steering, cab climate control, electrical systems, platform and cab, and safety instructions. Each section provides detailed information, specifications, and repair procedures for components and systems of the tractors.
New holland t8.350 continuously variable transmission (cvt) tractor service r...fujsefkksekfm
The document is a service manual that provides maintenance instructions for engine components of various tractor models. It includes sections on the engine and crankcase, cylinder heads, air cleaners and lines, fuel filters, fuel tanks, fuel injection system, engine lubrication system, aftercooler, engine cooling system, fan and drive, and selective catalytic reduction exhaust treatment. Each section provides detailed instructions, specifications, and diagrams for servicing the corresponding component.
New holland t8.320 continuously variable transmission (cvt) tractor service r...fujsefkksekfm
This document is a service manual for CNH Industrial tractor models T8.320 through T8.435, including SmartTrax versions. The manual contains over 50 sections that provide information on repairing and maintaining the engine, transmission, axles, hydraulics, electrical systems, cab climate control, and other components of the tractors. Each section includes detailed technical specifications, diagrams, and repair procedures.
New holland t8.275 tractor service repair manualfujsefkksekfm
This service manual provides information for servicing the engines in T8 tractor models T8.275, T8.300, T8.330, T8.360, and T8.390. The manual covers systems such as the engine and crankcase, cylinder heads, fuel system, cooling system, and electrical systems. It provides specifications, maintenance procedures, and troubleshooting information for servicing these models.
New holland t7.170 auto command tractor service repair manualfujsefkksekfm
The document is a service manual that provides technical specifications, descriptions of functionality, and troubleshooting information for the hydraulic, pneumatic, electrical, and electronic systems of various tractor models. It includes sections that describe the primary and secondary hydraulic power systems, hydraulic control systems, pneumatic systems, electrical power systems, electronic systems, and fault codes. The primary hydraulic power system section provides specifications for the hydraulic pump and charge pump, as well as descriptions of how the primary hydraulic system functions statically for different tractor models.
New holland t6.140 auto command tractor service repair manualfujsefkksekfm
This section provides technical specifications and service procedures for the engine and crankcase, including torque specifications for connecting the engine, instructions for disconnecting engine components for the T6.155-T6.175 models, and procedures for reconnecting and removing the engine on the T6.155.
New holland t4.110 v tractor service repair manualfujsefkksekfm
This document is a service manual that provides technical specifications and repair/maintenance instructions for various tractor models and components. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front axle system, and other components. The manual lists the applicable engine for each tractor model and market. It also provides an overview of the contents and organization of the manual.
New holland t4.110 n tractor service repair manualfujsefkksekfm
This document is a service manual that provides specifications and repair/maintenance procedures for various tractor models and components. It includes sections covering the engine, clutch, transmission, four-wheel drive system, front axle system, and other components. The manual lists the applicable engine for each tractor model and market. It also includes an index of contents to guide users to the relevant sections for different components.
New holland t4.95 f tractor service repair manualfujsefkksekfm
This document is a service manual for T4.75F, T4.85F, T4.95F, and T4.105F tractor models and their LP variants. It contains sections covering the engine, transmission, axles, hydraulics, hitches, steering, wheels, climate control, and electrical systems. Each section includes subsections that provide information on specific components and their repair or service. The manual also lists the engine type for each tractor model and market.
New holland ls185.b skid steer loader service repair manualfujsefkksekfm
The document is a workshop manual that provides technical information for repairing and servicing components of excavator models LS180.B, LS185.B, and LS190.B. It contains sections on the machine's distribution systems, power production, power train, travel, body and structure, and working arm. The primary hydraulic power system chapter provides specifications, diagrams, maintenance procedures, and troubleshooting information for components of the hydraulic system like the hydraulic pump, relief valve, reservoir, and oil filter. Procedures include cleaning, testing, disassembly, inspection, assembly, removal and installation of system components.
New holland c238 200 series compact track loader service repair manualfujsefkksekfm
This document is a service manual for New Holland 200 Series skid steer loaders and compact track loaders, covering models C227, C232, C238, L213, L215, L218, L220, L223, L225, and L230. The manual contains sections on hydraulic, pneumatic, electrical and electronic systems, engines and PTO systems, transmissions, axles, brakes, steering, frames, cabs, user controls, positioning, tool attachment, hitching, digging and landscaping functions. Safety precautions and general specifications such as torque values are provided at the beginning.
This document is a service manual that provides safety and technical information for maintaining Command vertical crankshaft engines, models CV11-16, CV460-465, and CV490-495. The manual contains 11 sections covering topics such as safety, troubleshooting, air and fuel systems, electrical systems, disassembly, inspection, and reassembly. The introduction section emphasizes important safety precautions and provides information on identifying engine models. It also recommends using high-quality detergent oil and unleaded gasoline as fuel.
Hyster k005 (h4.00 xm 5 europe) forklift service repair manualfujsefkksekfm
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The hood repair section includes adjusting the hood latch and striker for proper operator restraint. Radiator repair involves draining coolant before removing hoses and the radiator from the lift truck.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
8. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your NEW HOLLAND Sales and Service Networks.
48017760 14/11/2016
3
9. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
48017760 14/11/2016
5
10. INTRODUCTION
Safety rules - Ecology and the environment
Soil, air, and water quality is important for all industries and life in general. When legislation does not yet rule the
treatment of some of the substances that advanced technology requires, sound judgment should govern the use and
disposal of products of a chemical and petrochemical nature.
Familiarize yourself with the relative legislation applicable to your country, and make sure that you understand this
legislation. Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, anti-freeze,
cleaning agents, etc., with regard to the effect of these substances on man and nature and how to safely store, use,
and dispose of these substances.
Helpful hints
• Avoid the use of cans or other inappropriate pressurized fuel delivery systems to fill tanks. Such delivery systems
may cause considerable spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of these products contain substances
that may be harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when you drain fluids such as used engine coolant mixtures, engine oil, hydraulic fluid, brake fluid,
etc. Do not mix drained brake fluids or fuels with lubricants. Store all drained fluids safely until you can dispose of
the fluids in a proper way that complies with all local legislation and available resources.
• Do not allow coolant mixtures to get into the soil. Collect and dispose of coolant mixtures properly.
• The air-conditioning system contains gases that should not be released into the atmosphere. Consult an air-condi-
tioning specialist or use a special extractor to recharge the system properly.
• Repair any leaks or defects in the engine cooling system or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding. Penetrating weld splatter may burn a hole or weaken hoses, allowing the loss of oils,
coolant, etc.
Battery recycling
Batteries and electric accumulators contain several substances that can have a harmful
effect on the environment if the batteries are not properly recycled after use. Improper
disposal of batteries can contaminate the soil, groundwater, and waterways. NEW
HOLLAND strongly recommends that you return all used batteries to a NEW HOLLAND
dealer, who will dispose of the used batteries or recycle the used batteries properly. In
some countries, this is a legal requirement.
Mandatory battery recycling
NOTE: The following requirements are mandatory in Brazil.
Batteries are made of lead plates and a sulfuric acid solution. Because batteries contain heavy metals such as lead,
CONAMA Resolution 401/2008 requires you to return all used batteries to the battery dealer when you replace any
batteries. Do not dispose of batteries in your household garbage.
Points of sale are obliged to:
• Accept the return of your used batteries
• Store the returned batteries in a suitable location
• Send the returned batteries to the battery manufacturer for recycling
48017760 14/11/2016
6
14. Engine - Cylinder heads
Cylinder head - Static description
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Cylinder Head and Valve Train Components
The cylinder head incorporates the valve assemblies, rocker arms, rocker shaft, push rods, and lifters. A swirl cham-
ber located between the injector assembly and the main combustion chamber of the cylinders provides improved
starting and greater fuel efficiency. Initial combustion starts in the precombustion chamber and as the expansion oc-
curs a strong swirl pattern is created in the main combustion chamber for more complete combustion of the air-fuel
mixture. The air intake manifold is separate from the cast aluminum valve cover on all these engines. The exhaust
manifold is bolted on the left-hand side of the cylinder head on each of the models. Cylinder heads have integral valve
guides. Standard size valves only are used.
The cylinder block assembly contains the pistons, connecting rods, crankshaft, timing gears, and engine oil pump.
The crankshaft is supported on five main bearings. The front bearing is positioned in a bore in front of the block. The
other bearings are split liners located in holders bolted to the block. The camshaft is supported on four ball bearings
located in the block.
7607624950 1
Engine models ISM N844 and ISM N844L
48017760 14/11/2016
10.2 [10.101] / 4
15. Engine - Cylinder heads
Valve cover - Install
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Valve drive and gears - Clearance (Valves) (10.106).
1. Install a new gasket (1) and position the valve cover (2)
over the rocker arms.
2. Install the valve cover retaining bolts (3), and tighten to
12 - 16 N·m (9 - 19 lb ft).
3. Install and tighten the seal washer (4), and cap nuts (5).
76075733A 1
Next operation:
Water pump - Install (with Cooling Fan) (10.400).
48017760 14/11/2016
10.2 [10.101] / 5
16. Engine - Cylinder heads
Cylinder head - Compression test
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Compression test is performed through the glow plug ports. The test adapter tool (1), is equipped with quick coupler
ends for easy installation of the hose and gauge.
The procedures to perform a compression test are as follows:
1. Remove the wire lead from the fuel injection pump so-
lenoid.
2. Remove the glow plug electrical wire and wire connec-
tor from top of the glow plugs.
SECT10C01PG17_1 1
3. Remove all of the glow plugs.
NOTE: Be sure all the glow plugs are removed before starting the compression tests.
4. Install the adapter Tool No. FNH00120 , hose and
gauge assembly OEM1074 (2), in each port and crank
the engine until pressure stabilizes. The gauge should
read 2944 kPa (427 psi) ) plus or minus 345 kPa
(50 psi) .
SECT10C01PG17_2 2
NOTE: It may be necessary to remove some injector fuel lines to install the adapter tool.
NOTE: There should not be more than 345 kPa (50 psi) variation between the cylinders.
5. When all cylinders have been tested, reinstall the glow
plugs and electrical connections.
48017760 14/11/2016
10.2 [10.101] / 6
17. Engine - Cylinder heads
Cylinder head - Remove
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Rocker Arm Shaft and Support Bracket - Remove; See: “Engine Disassemble”..
1. Remove the valve stem caps (1), and push rods (2).
2. To remove the cylinder head, remove the cylinder head
bolts (3), by alternately loosening a half turn at a time
to prevent warping the head.
NOTE: Keep all valve components in separately marked
containers for reassembly in their original location.
20093361A 1
Next operation:
Valve Tappet - Removal; See: “Engine Disassemble”.
48017760 14/11/2016
10.2 [10.101] / 7
18. Engine - Cylinder heads
Cylinder head - Inspect
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Crankcase gears - Remove - with Camshaft (10.114).
1. Disassembly
1. Clean the cylinder head and remove any carbon
deposits from around the valve heads.
2. Use a valve spring compressor and remove the
valve spring retainer locks (1), spring (2), and
spring retainer (3), from each valve (4).
3. Remove the valves and place the valve compo-
nents together in separately marked containers for
reassembly in their original position.
20093369 1
2. Inspection and Repair
1. Clean all carbon deposits from the combustion
chamber and valve ports using a wire brush and
scraper.
2. Clean all dirt and residue from the gasket surface
using care not to scratch or nick the machined sur-
face.
3. Clean the cylinder head in solvent and air dry.
4. Inspect the head for cracks or damage in the fol-
lowing areas:
• Valve ports
• Valve seats (2).
• Prechamber (3).
• External cracks in the water jackets (1)..
5. Inspect the gasket surfaces for scratches or nicks,
which could cause leakage.
6. Examine the core hole plugs for rust or signs of
leakage. If a plug shows signs of damaging rust or
leakage, replace all plugs in the head.
7. Inspect the prechamber for carbon deposits and
looseness. Remove any carbon deposits found.
If prechamber is found to be loose, cylinder head
may be warped.
20093370 2
48017760 14/11/2016
10.2 [10.101] / 8
19. Engine - Cylinder heads
3. Inspection, Continued
• Use a straight edge and a feeler gauge and check
the cylinder head for warp lengthwise, crosswise,
and diagonally
20093371F 3
Next operation:
Valve drive and gears - Inspect - Valve Seats (10.106).
48017760 14/11/2016
10.2 [10.101] / 9
20. Engine - Cylinder heads
Cylinder head - Replace (Gasket)
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
During assembly, the ultimate engine compression ratio is established by the thickness of the head gasket used. For
service replacement, head gaskets of different thickness are available. The correct head gasket must be selected
based upon the amount the piston protrudes above the face of the block when at top dead center. The correct head
gasket usage is determined as follows:
Head Gasket Selection
1. Position each of the pistons at top dead center and, us-
ing a dial indicator, determine the distance each piston
projects above the face of the block.
NOTE: Measure each of the pistons while holding a slight
down pressure on the piston. Use the dimension taken
from the cylinder which has the greatest projection and se-
lect a head gasket as indicated in the following chart.
NOTE: The variation in the amount of protrusion among all
pistons must be within 0.1 mm (0.004 in).
20002377 1
Selection Chart
Engine Model Measurement Value Head Gasket Part No. Installed Thickness
ISM N844
0.5 - 0.6 mm (0.0197 -
0.0236 in)
111147510 1.2 mm (0.0472 in)
0.6 - 0.7 mm (0.0236 -
0.02756 in)
111147520 1.3 mm (0.0512 in)
ISM N844L
0.5 - 0.6 mm (0.0197 -
0.0236 in)
1111477711 1.2 mm (0.0472 in)
0.6 - 0.7 mm (0.0236 -
0.02756 in)
111147721 1.3 mm (0.0512 in)
Next operation:
Cylinder head - Install (10.101).
48017760 14/11/2016
10.2 [10.101] / 10
21. Engine - Cylinder heads
Cylinder head - Assemble
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Valve drive and gears - Inspect - Push Rods (10.106).
1. Insert each valve in the guide from which it was re-
moved and lightly lap the valve to be sure of an even
seat around the valve face. Remove the valve and re-
move all traces of lapping compound.
2. Install new intake valve seals on the valve guides using
a suitable driver.
3. Using a spring compressor, assemble the valves,
springs, retainers, and keepers.
Next operation:
Crankcase - Inspect (10.001).
48017760 14/11/2016
10.2 [10.101] / 11
22. Engine - Cylinder heads
Cylinder head - Install
Prior operation:
Cylinder head - Replace (Gasket) (10.101).
1. Install the valve tappets (1).
20093430 1
2. Select the proper head gasket and place it on the block
with the side marked with the last four digits of the part
code no. up.
3. Tighten the head bolts in the sequence as shown.
Tighten first to half torque value, then to the final torque
specification of 98 - 103 N·m (72.3 - 76 lb ft).
4. Replace the push rods and valve stem caps in their
original location.
5. Install the rocker shaft support assembly onto the head
and tighten the bolts to 27 - 39 N·m (20 - 29 lb ft).
20002380 2
Next operation:
Valve drive and gears - Clearance (Valves) (10.106).
48017760 14/11/2016
10.2 [10.101] / 12
23. Engine - Pan and covers
Timing gear housing - Remove
Prior operation:
Engine block cover Front - Remove (10.102)
1. Drain the engine crankcase oil.
2. Remove the crankshaft pulley.
3. Loosen the four injection pump mounting bolts (2), and
raise the injection pump (3), enough to remove the
spring pin (1), and separate the governor link from the
control rack. Remove the injection pump.
SECT10C01PG42 1
4. Insert a small dowel (1), through the fuel shutoff so-
lenoid hole and slide the control rack (2), in to allow
enough clearance to the cylinder block, for the pump to
be removed.
20002371E 2
5. Remove the through bolts and nuts (1), and remove the
steering pump from the front cover. Cap the lines and
pump openings.
NOTE: Two of the power steering pump retaining bolts are
not shown.
76075734B 3
48017760 14/11/2016
10.3 [10.102] / 3
24. Engine - Pan and covers
6. Install and tighten two nuts (1), against each other, onto
the retaining studs (2). Remove the studs (2), and the
hydraulic pump (3).
76075735 4
7. Remove the retaining nut (1). Pull crankshaft pulley (2),
and key (4), off of crankshaft (3).
76075736 5
48017760 14/11/2016
10.3 [10.102] / 4
25. Engine - Pan and covers
8. Remove the retaining bolts (1), and lift the cover (2), off
the locating dowels.
SECT10C01PG44_2 6
Next operation:
Timing gear housing - Visual inspection (10.102)
Next operation:
Crankcase gears - Remove - with Camshaft (10.114).
48017760 14/11/2016
10.3 [10.102] / 5
26. Engine - Pan and covers
Timing gear housing - Visual inspection
Prior operation:
Engine flywheel - Inspect (10.103).
1. The timing gear housing (3), contains the front oil seal
(1), power steering seal (4), and the governor linkage
assembly (2). See "Governor Assembly", for governor
linkage repair and replacement procedures.
10044360A 1
Front Oil Seal and Steering Pump Seal Replacement
2. Remove the front oil seal (1), from the timing gear cover
(3), and insert a new oil seal in its place.
3. Remove the steering pump seal (4), located on the front
of the timing gear cover, and replace with a new seal.
10044360B 2
Next operation:
Water pump - Inspect (10.400).
48017760 14/11/2016
10.3 [10.102] / 6
27. Engine - Pan and covers
Timing gear housing - Install
Prior operation:
Crankcase gears - Install (Idler Gear, Oil Pump, and Injection Timing) (10.114).
1. Install new cover gasket.
2. Insert the governor linkage through the block.
3. Rotate the oil pump cover to position the spring pin hole
(2).
4. Install cover locating pin in the oil pump cover plate.
10044361B 1
5. Install the cover retaining bolts (1).
SECT10C01PA44_2 2
Next operation:
Crankshaft - Install (Pulley) (10.103).
48017760 14/11/2016
10.3 [10.102] / 7
28. Engine - Pan and covers
Engine block cover Front - Remove
1. Remove the crankcase ventilation system (1). Refer to
Crankcase ventilation system - Remove (10.304) for
the proper procedure.
NHIL14ENG0610AA 1
2. Remove the crankshaft pulley bolts (2).
3. Remove the crankshaft pulley (3).
4. Remove the connector for the camshaft sensor (1).
NHIL14ENG0611AA 2
5. Remove the cover retaining bolts (1).
NOTE: Take note of the bolt size and location.
6. Remove the front cover (2).
NHIL14ENG0612AA 3
Next operation:
Engine block cover Front - Install (10.102)
48017760 14/11/2016
10.3 [10.102] / 8
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Engine - Pan and covers
Engine block cover Front - Install
Prior operation:
Engine block cover Front - Remove (10.102)
1. Clean the sealing surface (1) of the cover.
NHIL14ENG0614AA 1
2. Clean the sealing surface (1) of timing gear housing.
NHIL14ENG0613AA 2
3. Install the front cover (1) with a new gasket.
4. Loosely install two bolts (2) to hold everything in place.
NHIL14ENG0616AA 3
5. Install the crankcase ventilation drive hub (1).
6. Torque the nut to 80 N·m (59 lb ft).
NHIL14ENG0615AA 4
48017760 14/11/2016
10.3 [10.102] / 9
31. Engine - Pan and covers
7. Install the lower alignment tool 380100280 (2) on the
crankshaft.
8. Install the upper alignment tool 380100281 (1) onto the
drive hub to align the front cover.
83119829 5
9. Install the remainder of the front cover retaining bolts
(1).
10. Torque the front cover retaining bolts (1) to 20 - 30 N·m
(15 - 22 lb ft).
11. Remove the alignment tools.
NHIL14ENG0612AA 6
Next operation:
Crankcase ventilation system - Install (10.304)
48017760 14/11/2016
10.3 [10.102] / 10
32. Engine - Pan and covers
Engine oil pan - Remove
NOTE: Oil pan images may vary depending on your model.
1. Drain the engine oil.
2. Remove the oil pan bolts (3).
3. Remove the oil pan retaining plate (2).
4. Remove the oil pan (1).
NHIL14ENG0605AA 1
5. Remove the pick up tube support bolts (2).
6. Remove the Allen head bolt (1) from the pick up tube.
7. Remove the pick up tube (3) from the engine block.
NHIL14ENG0606AA 2
Next operation:
Engine oil pan - Install (10.102)
48017760 14/11/2016
10.3 [10.102] / 11
33. Engine - Pan and covers
Engine oil pan - Install
Prior operation:
Engine oil pan - Remove (10.102)
NOTE: Oil pan images may vary depending on your model.
1. Install a new O-ring (1) on the pick up tube.
NHIL14ENG0607AA 1
2. Install the oil pick up tube (3) into the engine block until
the O-ring seats.
3. Install the Allen head bolt (1) into the pick up tube.
4. Torque the tube bolt (1) to 10 N·m (7 lb ft).
5. Install the two M10 x 20 bolts (2) into the pick up tube
support.
6. Torque the pick up tube support bolts (2) to 45 N·m
(33 lb ft).
NHIL14ENG0606AA 2
7. Install the new gasket (1) on the oil pan (2).
NHIL14ENG0609AA 3
48017760 14/11/2016
10.3 [10.102] / 12
34. Engine - Pan and covers
8. Install the oil pan (1) with the oil pan retaining plate (2).
9. Install the oil pan retaining bolts (3).
10. Torque the bolts (3) as follows:
• M10 x 35 = 45 N·m (33 lb ft)
• M8 x 35 = 25 N·m (18 lb ft)
NHIL14ENG0605AA 4
48017760 14/11/2016
10.3 [10.102] / 13
35. Engine - Crankshaft and flywheel
Engine flywheel - Inspect
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Crankcase gears - Inspect (Camshaft) (10.114).
1. Inspect the ring gear for cracked, broken, chipped, or
worn gear teeth. If found damaged, replace the ring
gear.
2. If necessary, remove the starter ring gear using a ham-
mer and chisel to crack the ring gear.
20093403 1
3. To reinstall a new ring gear, heat the new ring gear
to 120 - 150 °C (245 - 300 °F) from the inside only.
Be careful not to overheat the ring gear teeth. Use a
temperature sensitive crayon to mark the inside of the
ring gear. Quench the ring gear quickly to obtain a good
shrink fit onto the flywheel.
Next operation:
Timing gear housing - Visual inspection (10.102) .
48017760 14/11/2016
10.4 [10.103] / 4
36. Engine - Crankshaft and flywheel
Engine flywheel - Install
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Rear Oil Seal and Backplate Install.
1. Fit the flywheel (2), to the crankshaft (1), and align the
bolt holes.
2. Install the flywheel retaining bolts and tighten to 69 -
78 N·m (51 - 57 lb ft).
20093407A 1
Next operation:
Connecting rod and piston - Install (10.105).
48017760 14/11/2016
10.4 [10.103] / 5
37. Engine - Crankshaft and flywheel
Engine flywheel - Remove
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Connecting rod and piston - Remove (10.105).
1. Loosen the flywheel retaining bolts.
2. Using a brass drift and hammer, tap the end of the
crankshaft (1), to loosen the flywheel (2), from the shaft.
20093407 1
Next operation:
Backplate and Oil Seal - Remove; See: ”Engine Disassemble”..
48017760 14/11/2016
10.4 [10.103] / 6
38. Engine - Crankshaft and flywheel
Crankshaft - Inspect (Main Bearing and Thrust Washer)
Boomer™ 3040 CVT WE
Boomer™ 3045 CVT WE
Boomer™ 3050 CVT WE
Prior operation:
Connecting rod and piston - Assemble (10.105).
Removal and Inspection
20044366 1
(1) Holder
(2) Upper Main Liner (with oil groove)
(3) Thrust Bearing
(4) Lower Main Liner (no oil groove)
1. Remove the two retaining bolts from the bearing hold-
ers (1).
2. Remove the bearing holders and bearing liners (2).
3. Position a piece of plastigauge across the full width of
the bearing liners.
4. Install the bearing holder and tighten the bolts to 49.0 -
53.9 N·m (36.2 - 39.8 lb ft).
NOTE: Do not permit the bearing holder to rotate, even the slightest amount.
5. Remove the bearing holders and measure the width of
the flattened plastigauge using the gauge printed on the
plastigauge package.
48017760 14/11/2016
10.4 [10.103] / 7