This service manual document provides information on servicing various components of a grape harvester, including the rear axle system, hydrostatic drive system, brakes and controls, hydraulic systems, frames and ballasting, steering, electrical systems, grape harvester shaking system, and cleaning system. The document contains sections on technical data, functional data, diagnostic data, and service procedures for repairing and replacing components.
MAXXUM 110 Multicontroller EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
MAXXUM 115 EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operational descriptions, troubleshooting information, and repair/replacement procedures.
MAXXUM 115 Multicontroller EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors. It contains sections covering the engine, transmission, axles, brakes, hydraulics and other systems. Each section includes technical data, functional descriptions, diagnostics and service procedures. The manual is intended for use by Case IH service technicians when repairing or maintaining the listed tractor models.
MAXXUM 110 EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
CASE IH Steiger 580 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 600 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2023. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety precautions are included to prevent injury while working on the equipment.
CASE IH Rowtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
New Holland E70BSR ROPS Tier III Midi Crawler Excavator Service Repair Manual...fujskekdmmd
This service manual provides information for maintenance and repair of a ROPS Tier III Midi Crawler Excavator. It includes safety precautions, specifications, maintenance schedules and procedures, system descriptions, disassembly and assembly instructions, troubleshooting guides, and engine information. The manual is organized into sections covering topics such as specifications, maintenance, systems, disassembly, troubleshooting, and engines. Safety is emphasized throughout, with warnings and cautions provided.
MAXXUM 110 Multicontroller EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
MAXXUM 115 EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operational descriptions, troubleshooting information, and repair/replacement procedures.
MAXXUM 115 Multicontroller EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors. It contains sections covering the engine, transmission, axles, brakes, hydraulics and other systems. Each section includes technical data, functional descriptions, diagnostics and service procedures. The manual is intended for use by Case IH service technicians when repairing or maintaining the listed tractor models.
MAXXUM 110 EP Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
CASE IH Steiger 580 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 600 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2023. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety precautions are included to prevent injury while working on the equipment.
CASE IH Rowtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
New Holland E70BSR ROPS Tier III Midi Crawler Excavator Service Repair Manual...fujskekdmmd
This service manual provides information for maintenance and repair of a ROPS Tier III Midi Crawler Excavator. It includes safety precautions, specifications, maintenance schedules and procedures, system descriptions, disassembly and assembly instructions, troubleshooting guides, and engine information. The manual is organized into sections covering topics such as specifications, maintenance, systems, disassembly, troubleshooting, and engines. Safety is emphasized throughout, with warnings and cautions provided.
New Holland E80BMSR Hydraulic Excavator Service Repair Manual.pdffujskekdmmd
This document provides general safety precautions and guidelines for repairing hydraulic excavators. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic equipment and electrical components, welding repairs, and environmental considerations. Measurement units used are also defined. Precautions are given for preparing the work area, blocking the machine, relieving pressures, lifting heavy components safely, and ensuring all guards and shields are in place before operation.
New Holland 9080L Grape Harvester Service Repair Manual.pdffujskekdmmd
This service manual document provides information on servicing various components of a grape harvester, including the rear axle system, hydrostatic drive system, brakes and controls, hydraulic systems, frames and ballasting, steering, electrical systems, grape harvester shaking system, and cleaning system. The document includes technical data, functional descriptions, diagnostic information, and service procedures for maintenance and repair of the harvester components.
New Holland 9080L H Grape Harvester Service Repair Manual.pdffujskekdmmd
This service manual document provides information on servicing various components of a grape harvester, including the rear axle system, hydrostatic drive system, brakes and controls, hydraulic systems, frames and ballasting, steering, electrical systems, grape harvester shaking system, and cleaning system. The document includes technical data, functional descriptions, diagnostic information, and service procedures for maintenance and repair of the harvester components.
CASE IH Steiger 470 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
New Holland C185 Compact Track Loader Service Repair Manual.pdffujskekdmmd
- The document provides instructions for decontaminating the primary hydraulic power system of a machine. This involves draining and replacing the hydraulic oil and filter, running the hydraulic cylinders to flush the system, then refilling the reservoir with new oil.
- It describes how to perform a flow test on the hydraulic pump relief valve to check that it is operating properly. This involves installing a flowmeter and measuring the pressure at which the relief valve begins to open and when it fully opens.
- Technical specifications and diagrams are provided for components in the primary hydraulic power system, including the hydraulic pump, relief valve, hydraulic cylinders, and reservoir. Maintenance and repair procedures are outlined.
New Holland 7030M Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides service instructions for removing the engine from a grape harvester. It outlines 27 steps for disconnecting all electrical connections, hoses, brackets and bolts that attach the engine to the harvester frame. This includes draining fluids, detaching wiring harnesses, removing cooling and air intake components. Proper support of the engine is emphasized when lifting it from the frame.
MAXXUM CVT 120 Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operational descriptions, troubleshooting information, and repair/replacement procedures.
MAXXUM CVT 130 Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
CASE IH Steiger 500 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and the tractor platform, cab, bodywork and decals. It provides maintenance and repair instructions for qualified dealership personnel.
CASE IH Steiger 500 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2014. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety warnings are included throughout regarding potential risks like rollovers, hydraulic fluid injection, and proper maintenance procedures. The manual is intended to guide technicians in servicing the listed tractor models.
CASE IH Steiger 540 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 620 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and includes safety information and maintenance procedures for various tractor systems and components. It provides maintenance instructions for the engine, transmission, front and rear axles, power take-off, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, electrical systems, and other parts. Safety precautions are included to prevent injury when servicing equipment.
CASE IH Steiger 550 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2014. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety precautions are included to prevent injury when working on or operating the tractors.
CASE IH PUMA 180 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual that contains sections covering the distribution systems, power production, power train, travelling, body and structure, and working arm systems of Case IH PUMA tractors. It provides information on primary and secondary hydraulic power systems, hydraulic and pneumatic components, electrical and electronic systems, engines, transmissions, axles, steering, brakes, suspensions, frames, operator platforms and hitches. The document also lists special tools needed for working on these systems.
New Holland VN2080 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document contains specifications for a self-propelled grape harvester model VN 2080, including two variants. It includes dimensions, weights, engine specifications, hydraulic and braking systems, sloping and tilting limits, and other technical details. The harvester has a 6-cylinder diesel engine producing 129 kW of power. Key dimensions vary slightly between the two variants which differ in axle clearance height. Performance is limited on slopes over 20% depending on the vineyard row spacing and presence of a destemmer.
New Holland SB65 Braud Service Repair Manual.pdffujskekdmmd
This document contains specifications for three versions of the SB65 self-propelled harvesting machine. It includes dimensions, weights, engine details, hydraulic system components, and other technical specifications. The sections cover identification, commercial descriptions, dimensions, weights, fuel/cooling systems, drive components, braking, platform/cab features, and lighting. Diagrams are provided to illustrate the machine configurations and key components.
New Holland SB62 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides a service manual for various grape harvester models (SB36, SB56, SB58, SB60, SB62, SB64). It includes 3 pages of detailed specifications and descriptions of the harvester components, such as the shaking header, rotor collectors, cleaning system, containers, self-propelled machine frame, and tires. The manual provides technical information needed for maintenance and repair of the harvesters.
New Holland SB64 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides a service manual for various grape harvester models (SB36, SB56, SB58, SB60, SB62, SB64). It includes 3 pages of detailed specifications and descriptions of the harvester components, such as the shaking header, rotor collectors, cleaning system, containers, self-propelled machine frame, and tires. The manual provides technical information needed for maintenance and repair of the harvesters.
CASE IH Steiger 420 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 370 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and includes safety information and maintenance procedures for various tractor systems and components. It provides maintenance instructions for the engine, transmission, front and rear axles, power take-off, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, electrical systems, and other parts. Safety precautions are included to prevent injury when servicing equipment.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
New Holland E80BMSR Hydraulic Excavator Service Repair Manual.pdffujskekdmmd
This document provides general safety precautions and guidelines for repairing hydraulic excavators. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic equipment and electrical components, welding repairs, and environmental considerations. Measurement units used are also defined. Precautions are given for preparing the work area, blocking the machine, relieving pressures, lifting heavy components safely, and ensuring all guards and shields are in place before operation.
New Holland 9080L Grape Harvester Service Repair Manual.pdffujskekdmmd
This service manual document provides information on servicing various components of a grape harvester, including the rear axle system, hydrostatic drive system, brakes and controls, hydraulic systems, frames and ballasting, steering, electrical systems, grape harvester shaking system, and cleaning system. The document includes technical data, functional descriptions, diagnostic information, and service procedures for maintenance and repair of the harvester components.
New Holland 9080L H Grape Harvester Service Repair Manual.pdffujskekdmmd
This service manual document provides information on servicing various components of a grape harvester, including the rear axle system, hydrostatic drive system, brakes and controls, hydraulic systems, frames and ballasting, steering, electrical systems, grape harvester shaking system, and cleaning system. The document includes technical data, functional descriptions, diagnostic information, and service procedures for maintenance and repair of the harvester components.
CASE IH Steiger 470 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
New Holland C185 Compact Track Loader Service Repair Manual.pdffujskekdmmd
- The document provides instructions for decontaminating the primary hydraulic power system of a machine. This involves draining and replacing the hydraulic oil and filter, running the hydraulic cylinders to flush the system, then refilling the reservoir with new oil.
- It describes how to perform a flow test on the hydraulic pump relief valve to check that it is operating properly. This involves installing a flowmeter and measuring the pressure at which the relief valve begins to open and when it fully opens.
- Technical specifications and diagrams are provided for components in the primary hydraulic power system, including the hydraulic pump, relief valve, hydraulic cylinders, and reservoir. Maintenance and repair procedures are outlined.
New Holland 7030M Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides service instructions for removing the engine from a grape harvester. It outlines 27 steps for disconnecting all electrical connections, hoses, brackets and bolts that attach the engine to the harvester frame. This includes draining fluids, detaching wiring harnesses, removing cooling and air intake components. Proper support of the engine is emphasized when lifting it from the frame.
MAXXUM CVT 120 Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operational descriptions, troubleshooting information, and repair/replacement procedures.
MAXXUM CVT 130 Tier 4A Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Maxxum tractors covering models MAXXUM 110 EP through MAXXUM 140 EP and MAXXUM CVT 110 through MAXXUM CVT 130. The manual contains sections on the engine, transmission, hydraulics, electrical systems, and other components. It provides technical specifications, operating descriptions, diagnostic procedures, and service instructions.
CASE IH Steiger 500 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and the tractor platform, cab, bodywork and decals. It provides maintenance and repair instructions for qualified dealership personnel.
CASE IH Steiger 500 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2014. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety warnings are included throughout regarding potential risks like rollovers, hydraulic fluid injection, and proper maintenance procedures. The manual is intended to guide technicians in servicing the listed tractor models.
CASE IH Steiger 540 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 620 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and includes safety information and maintenance procedures for various tractor systems and components. It provides maintenance instructions for the engine, transmission, front and rear axles, power take-off, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, electrical systems, and other parts. Safety precautions are included to prevent injury when servicing equipment.
CASE IH Steiger 550 Tier 4 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2013-2014. It provides specifications, maintenance procedures, and troubleshooting information for the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety precautions are included to prevent injury when working on or operating the tractors.
CASE IH PUMA 180 Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual that contains sections covering the distribution systems, power production, power train, travelling, body and structure, and working arm systems of Case IH PUMA tractors. It provides information on primary and secondary hydraulic power systems, hydraulic and pneumatic components, electrical and electronic systems, engines, transmissions, axles, steering, brakes, suspensions, frames, operator platforms and hitches. The document also lists special tools needed for working on these systems.
New Holland VN2080 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document contains specifications for a self-propelled grape harvester model VN 2080, including two variants. It includes dimensions, weights, engine specifications, hydraulic and braking systems, sloping and tilting limits, and other technical details. The harvester has a 6-cylinder diesel engine producing 129 kW of power. Key dimensions vary slightly between the two variants which differ in axle clearance height. Performance is limited on slopes over 20% depending on the vineyard row spacing and presence of a destemmer.
New Holland SB65 Braud Service Repair Manual.pdffujskekdmmd
This document contains specifications for three versions of the SB65 self-propelled harvesting machine. It includes dimensions, weights, engine details, hydraulic system components, and other technical specifications. The sections cover identification, commercial descriptions, dimensions, weights, fuel/cooling systems, drive components, braking, platform/cab features, and lighting. Diagrams are provided to illustrate the machine configurations and key components.
New Holland SB62 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides a service manual for various grape harvester models (SB36, SB56, SB58, SB60, SB62, SB64). It includes 3 pages of detailed specifications and descriptions of the harvester components, such as the shaking header, rotor collectors, cleaning system, containers, self-propelled machine frame, and tires. The manual provides technical information needed for maintenance and repair of the harvesters.
New Holland SB64 Grape Harvester Service Repair Manual.pdffujskekdmmd
This document provides a service manual for various grape harvester models (SB36, SB56, SB58, SB60, SB62, SB64). It includes 3 pages of detailed specifications and descriptions of the harvester components, such as the shaking header, rotor collectors, cleaning system, containers, self-propelled machine frame, and tires. The manual provides technical information needed for maintenance and repair of the harvesters.
CASE IH Steiger 420 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Steiger 370 Tier 4B (final) Tractor Service Repair Manual.pdffujskekdmmd
This document is a service manual for Case IH tractors and includes safety information and maintenance procedures for various tractor systems and components. It provides maintenance instructions for the engine, transmission, front and rear axles, power take-off, brakes, hydraulics, hitches, frames, steering, wheels, tracks, cab climate control, electrical systems, and other parts. Safety precautions are included to prevent injury when servicing equipment.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
3. Link Product / Engine
Product Market Product Engine
9040L Europe F4HE9484
9040L International Region F4HE9484
null [HAG00690K00002 - ] Europe F4HE9687
null [HAG00690K00002 - ] International Region F4HE9687
9080L International Region F4HE9687
9080L Europe F4HE9687
9090L Europe F4HE9687
9090L International Region F4HE9687
9040M Europe F4HE9484
9040M International Region F4HE9484
84490331C 27/03/2014
4. Contents
INTRODUCTION
Rear axle system........................................................................ 27
[27.100] Powered rear axle.................................................................. 27.1
Hydrostatic drive......................................................................... 29
[29.218] Pump and motor components...................................................... 29.1
[29.202] Hydrostatic transmission ........................................................... 29.2
Brakes and controls .................................................................... 33
[33.202] Hydraulic service brakes ........................................................... 33.1
Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems.................................................................. 35.1
[35.300] Reservoir, cooler, and filters........................................................ 35.2
[35.610] Machine leveling control system ................................................... 35.3
[35.946] Frame positioning lifting............................................................ 35.4
[35.903] Shaking hydraulic system .......................................................... 35.5
[35.904] Cleaning hydraulic system ......................................................... 35.6
[35.952] Destemmer system ................................................................ 35.7
[35.930] Conveyor receiver system ......................................................... 35.8
[35.736] Boom hydraulic system ............................................................ 35.9
Frames and ballasting ................................................................. 39
[39.100] Frame .............................................................................. 39.1
Steering..................................................................................... 41
[41.101] Steering control .................................................................... 41.1
Electrical systems....................................................................... 55
[55.000] Electrical system ................................................................... 55.1
[55.100] Harnesses and connectors......................................................... 55.2
[55.425] Boom, dipper, and bucket control system.......................................... 55.3
84490331C 27/03/2014
7. INTRODUCTION
Foreword
9000 L INT --- WE
9040M INT --- WE
IMPORTANT INFORMATION
All repair and maintenance operations described in this manual must be carried out exclusively by the New Holland
Service network, strictly complying with the instructions provided and using specific tools as required.
Any operator who carries out the operations specified in this document without complying strictly with the instructions
provided shall be personally liable for the damages that may result.
The manufacturer and all organizations in its distribution chain, including, without limitation, national, regional, and
local dealers, do not accept any liability for damages resulting from a malfunction of parts and/or components not ap-
proved by the manufacturer and used for maintenance operations and/or repair of products manufactured or marketed
by the manufacturer. In no case is a warranty granted to the product manufactured or marketed by the manufacturer
in case of damage caused by improper operation of parts and/or components not approved by the manufacturer.
No reproduction, partial or complete, of the text or illustrations is permitted.
84490331C 27/03/2014
3
8. INTRODUCTION
Foreword
Technical Information
This information in this manual has been structured using a unique coding environment. This is the way in which
technical information is created, stored and retrieved in the Technical Information Database. The location (on the
machine) has been coded using SAP coding to align locations with the warranty system.
The coding classifies all information in three ways.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g., Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model that the piece of technical information is written for.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customers concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
How to Use this Manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
84490331C 27/03/2014
4
9. INTRODUCTION
Basic instructions
9000 L INT --- WE
9040M INT --- WE
SHIMMING
For each adjustment operation, select adjusting shims, individually measure using a micrometer, then add up the
recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, and do not rely on the
rated value indicated on each shim.
ROTATING SHAFT SEALS
For correct rotating shaft seal installation, proceed as follows:
• Before assembly, allow the seal to soak for at least thirty minutes in the oil it will be sealing.
• Thoroughly clean the shaft, and check that the working surface on the shaft is undamaged.
• Fit the lip seal toward the fluid. If you are fitting a hydrodynamic lip seal, the grooves should be oriented so that the
fluid is directed toward the inner side of the seal (take the shaft direction of rotation into consideration).
• Coat the lip seal with a thin layer of lubricant (use oil rather than grease), then fill the gap between the lip seal and
the dust lip seal of the double-lip seals with grease.
• Insert the seal into its seat and press down using a flat punch. Do not tap the seal with a hammer or mallet.
• During assembly, make sure that the seal is fitted perpendicularly to its seat. Once this operation is completed,
check to make sure that the seal is in contact with the bearing stop, if required.
• To prevent damaging the lip seal on the shaft, fit an appropriate protective guard during installation.
"O" RINGS
Lubricate the "O" rings before fitting them into the seats. This prevents them from overturning and twisting, which
would make them ineffective.
SEALING COMPOUNDS
Apply one of the following sealing compounds to the mating surfaces marked with an X: Silmate RTV, Rhodorsil
CAF 1, or Loctite Plastic Gasket. Before applying the sealing compound, prepare the surfaces as follows:
• Remove any dirt using a metal brush.
• Thoroughly degrease the surfaces using one of the following cleaning agents: trichloroethylene, gasoline, or a
water and soda solution.
SPLIT PINS
When fitting split pins, make sure that the pin notch is positioned in the direction of the force required to stress the
pin. Spiral split pins do not require special positioning.
84490331C 27/03/2014
8
10. INTRODUCTION
PROTECTING THE ELECTRONIC/ELECTRICAL SYSTEMS DURING CHARGING OR WELD-
ING
To avoid damaging the electronic/electrical systems, always follow the safety instructions below:
1. Never make or break any of the charging circuit connections, including the battery connections, when the engine
is running.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the machine or any header attached
to the machine.
• Position the welder ground clamp as close to the welding area as possible.
• If welding in close proximity to a computer module, the module should be removed from the machine.
• Never allow welding cables to lay on, near, or across any electrical wiring or electronic component while welding
is in progress.
4. Always disconnect the negative cable from the battery when using a battery charger to carry out charging proce-
dures on the machine.
NOTICE: If welding has to be carried out on the machine or the header (if it is attached), disconnect the battery ground
cable from the machine battery. The electronic monitoring system and charging system will be damaged if this is not
done.
Remove the battery ground cable. Reconnect the cable when welding is completed.
WARNING
Battery acid causes severe burns. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Antidote - EXTERNAL: flush with water. INTERNAL: drink large quantities of water or milk. Follow with milk
of magnesia, beaten egg or vegetables oil. Call physician immediately. EYES: flush with water for 15 minutes
and get prompt medical attention.
84-110
84490331C 27/03/2014
9
12. Rear axle system - Powered rear axle
Rear axle - Transform - Changing the rear track -
9040L INT --- WE
9060L INT --- WE
9080L INT --- WE
9090L INT --- WE
NOTE: To change the rear track of the machine by 160 mm (6.3 in), you must turn over the wheel arm fastening
bearings. The bearings are moved by 40 mm (1.6 in).
1. Remove the corresponding rear wheel. To do this:
• Apply the parking brake.
• Lift the machine using its standalone system.
• Place a cubed wooden block measuring A = 450 mm
(17.7 in) under the rear wheel arm pivot.
• Lower the machine using its standalone system until
the wheel is just off the ground.
• Shut down the engine.
• Remove the wheel.
2. Remove the pin (1) of the height stop telescopic tube
(2).
COIL11GRH020A0B 1
3. Place a mobile lifting device under the wheel arm (3).
4. Remove the 4 fixing screws (4) from the 2 fastening
bearings (5).
COIL11GRH021A0B 2
5. Mark the position of the spacer rings (6).
ATTENTION: When reassembling, you must put spacer rings of the same thickness under each bearing.
84490331C 27/03/2014
27.1 [27.100] / 3
13. Rear axle system - Powered rear axle
6. Remove the spring retaining rings (7) and pull out the
bearings (5).
COIL11GRH022A0B 3
7. Fit the bearings (8) onto the wheel arms at the required
track width.
• Position A = wide track.
• Position B = narrow track.
8. Replace the spring retaining rings (7).
9. Replace the screws (4), inserting the corresponding
spacer rings. The tightening torque of the screws (4)
is 650 N·m (5753.0 lb in).
COIL11GRH023A0B 4
NOTE: The diagrams show the positions of the right-hand wheel arm. The bearings are always fitted in the same
holes located towards the outside of the machine. To change the track width, the bearings are simply turned over.
For information, the other holes are not used.
10. Replace the pin (1) of the height stop tube according
to the desired track width.
• Position A = wide track, the spacer (9) will be on the
outside of the chassis.
• Position B = narrow track, the spacer (9) will be on
the inside of the chassis.
COIL11GRH024A0B 5
11. Remove the mobile lifting device.
12. Replace the wheel. The tightening torque of the wheel
is 700 N·m (6195.5 lb in).
13. Start the engine and raise the machine using its hy-
draulic system. Remove the wooden wedge.
84490331C 27/03/2014
27.1 [27.100] / 4
14. Rear axle system - Powered rear axle
14. Adjust the side stops of the harvesting equipment.
• The diagram shows how the stop is fitted when the
machine track is in the wide position. The spacer
ring (10) is fitted inside the bracket.
• When the machine track is in the narrow position,
this spacer ring (10) must be fitted on the outside
of the bracket. The 2 spacer rings are both on the
outside of the bracket.
COIL11GRH025A0B 6
NOTE: The swinging of the harvesting machine will therefore be reduced.
84490331C 27/03/2014
27.1 [27.100] / 5
15. Hydrostatic drive - Pump and motor components
Pump - Remove - Forward control pump-
NOTE: When removing the hydraulic piping, have a suitable container readily available to capture any residual hy-
draulic oil.
1. Remove the shaker control pump. (see instructions)
Hydraulic systems - Remove - Shaker control pump
- (35.000).
2. Remove the cleaning control pump. (see instructions)
Hydraulic systems - Remove - Cleaning control
pump - (35.000).
3. Unscrew the four screws (2) from the inside of the ma-
chine to remove the connection block (3). This block
will remain at the end of the hoses.
NOTE: Recover the O-rings located between the block (3)
and the HP block (5).
4. Disconnect all the hoses (4) from the HP block (5).
5. Disconnect all the electrical cables (6) from the HP
block (5).
6. Take out the HP block (5) by removing the four fixing
screws.
ATTENTION: The component weighs approximately 45 kg
(99.2 lb). Install a suitable lifting device.
COIL10GRH444A0B 1
7. Disconnect all the hoses (7) from the pump (1).
8. Disconnect the two electrical cables (8) from the servo-
control unit.
9. Remove the four screws (9) and pull the pump (1) out.
ATTENTION: The component weighs approximately 83 kg
(183.0 lb). Install a suitable lifting device.
COIL10GRH445A0B 2
10. Remove the union installations (10) and plug the
pump ports.
84490331C 27/03/2014
29.1 [29.218] / 3
16. Hydrostatic drive - Pump and motor components
11. Unscrew the screw (11) and remove the sleeve (12).
COIL10GRH446A0B 3
84490331C 27/03/2014
29.1 [29.218] / 4
17. Hydrostatic drive - Pump and motor components
Pump - Install - Forward control pump-
NOTE: The component weighs approximately 83 kg (183.0 lb). Install a suitable lifting device.
1. Unplug the pump ports to fit the union installations (2).
2. Fit the drive shaft (3)sleeve. To do this:
• Slide the sleeve (3) onto the pump shaft (1) until the
external side is aligned with the end of the shaft.
• Tighten the screw (4) to a torque of 210 N·m
(1858.7 lb in).
COIL10GRH446A0C 1
3. Slide the pump (1) onto the motor output and secure it
using the four screws (5).
NOTE: The screws (5) are screwed down with normal
thread lock fluid and tightened to a torque of 200 N·m
(1770.1 lb in).
4. Connect all the hoses (5) to the pump, except the
drainage hose (7).
COIL10GRH447A0B 2
5. Connect the pump servo-control electrical cables.
NOTE: The forward motion circuit will not function correctly
unless the electrical connections correspond to those in the
diagram below.
COIL10GRH448A0B 3
6. Position the hydraulic HP block (8) under the pump
(1)and secure it using four screws (10) tightened to a
torque of 120 N·m (1062.1 lb in).
NOTE: Check the condition and position of the O-rings between the HP block and the pump.
7. Connect all the hoses (11) to the HP block (8).
84490331C 27/03/2014
29.1 [29.218] / 5
18. Hydrostatic drive - Pump and motor components
8. Connect all the electrical connectors to the HP block
(8).
COIL10GRH449A0B 4
NOTE: The forward motion circuit will not function correctly unless the electrical connections correspond to those in
the diagram.
9. Fasten the hydraulic block (12) to the inside of the ma-
chine using screws (13).
COIL10GRH450A0B 5
NOTE: Check the condition and position of the O-rings between the two hydraulic blocks.
10. The pump housing (1) must be filled before operating
the engine.
11. Method:
• Connect a hand pump to the filler coupling (B)
• Remove the breather filter (15) and plug the hose
(14).
• Add oil to the reservoir until it runs out of the uncon-
nected drainage hose (12) union.
ATTENTION: The pressure in the reservoir must never exceed 0.3 bar (4.4 psi).
12. Connect the drainage hose (7).
COIL10GRH443A0C 6
13. Re-fit the cleaning pump. (see instructions) Hydraulic
systems - Install - Cleaning control pump - (35.000)
84490331C 27/03/2014
29.1 [29.218] / 6
19. Hydrostatic drive - Pump and motor components
14. Re-fit the shaker pump. (see instructions) Hydraulic
systems - Install - Shaker control pump - (35.000)
15. Fit a manometer of 300 bar (4350.0 psi) minimum on
the standby Minimess connector (A) on the HP block
16. Remove the plug and re-fit the breather filter. (15)
17. Start the engine and immediately check that the force-
feed pressure increases. This means that the pump
is in operation.
COIL10GRH452A0B 7
18. Remove the manometer and check the oil level in the
hydraulic reservoir.
84490331C 27/03/2014
29.1 [29.218] / 7
20. Hydrostatic drive - Pump and motor components
Motor - Remove - Rear wheel motor -
9000 L INT --- WE
9040M INT --- WE
NOTE: When removing the hydraulic piping, have a suitable container readily available to capture any residual hy-
draulic oil.
1. Remove the corresponding rear wheel. To do this:
• Apply the parking brake.
• Lift the machine using its self-powered device.
• Place a cubed wooden block measuring X = 450 mm
(17.7 in) under the rear wheel arm pivot.
• Lower the machine using its self-powered device un-
til the wheel is just off the ground.
• Lock it in position by placing the telescopic tube pin
in (A).
• Remove the wheel.
COIL10GRH458A0B 1
2. Before disconnecting the motor hoses, the drainage
hose at the filter located at the front of the hydraulic
reservoir must be disconnected. This will prevent the
reservoir
from draining (1) Common drain for the two front and
rear left-hand wheel motors.
(2) Front right-hand wheel motor drain.
(3) Rear right-hand wheel motor drain.
COIL10GRH459A0B 2
3. For the rear left-hand wheel only, remove the speed
sensor and its bracket by removing the screws (4).
COIL10GRH007A0C 3
4. Disconnect and plug all the hoses (5).
NOTE: Recover the retaining clamp joints.
84490331C 27/03/2014
29.1 [29.218] / 8
21. Hydrostatic drive - Pump and motor components
5. Remove the fixing screws (6) and take out the motor.
COIL10GRH460A0B 4
ATTENTION: The component weighs approximately 160 kg (352.7 lb). Install a suitable lifting device.
6. Remove the hose installations from the motor and plug
them.
84490331C 27/03/2014
29.1 [29.218] / 9
22. Hydrostatic drive - Pump and motor components
Motor - Install - Rear wheel motor -
9000 L INT --- WE
9040M INT --- WE
ATTENTION: The component weighs approximately 160 kg (352.7 lb). Have a suitable lifting device ready.
1. Check that the motor is installed on the correct side of
the machine. These motors have a specific direction
of rotation. To ascertain the direction of rotation, check
the part number NEW HOLLAND on the manufacturer's
plate for the motor:
• 87672923 — right-hand motor.
• 87672924 — left-hand motor.
2. Slide the motor (1) into the wheel arm (2) and secure
it using the screws (3). The plate (4) will be placed on
the motor side. The tightening torque of the screws is
500 N·m (4425.4 lb in)
3. Fit the installations (5) and connect the corresponding
hoses.
4. Fit the HP hose flange joints (6) and secure them with
grease. Fit the flanges on the motor by tightening the
screws (7).
COIL10GRH461A0B 1
5. Before starting the hydraulic motor, its housing must
first be filled. To do this:
• Remove the bleed plug (B), located above the motor,
by passing a spanner through an existing hole in the
wheel arm.
• Fit a hand pump to the end of the drainage hose at
the filter located at the front of the hydraulic reservoir
(see removal instructions) Motor - Remove - Rear
wheel motor - (29.218)
• Pump oil into this hose until it runs out of the bleed
hole (B).
• Re-fit the bleed plug (B).
• Remove the pump and connect the drainage hose
(9).
COIL10GRH462A0B 2
6. Install the groundspeed sensor bracket (8) on the left-
hand motor only.
84490331C 27/03/2014
29.1 [29.218] / 10
23. Hydrostatic drive - Pump and motor components
7. Adjust the speed sensor. To do this:
• Press the target (disc) against the hub using the
wheel nuts.
• Position the bracket between (8) and 3 mm
(0.118 in) from the ends of the target (disc) (10).
• Tighten the fixing screws (9).
• Check that the sensor is positioned at a distance of
B = 4.3 mm (0.2 in) from the target (10), or adjust as
necessary.
COIL10GRH463A0B 3
8. Re-fit the wheel and tighten the nuts (11) to 700 N·m
(6195.5 lb in).
9. Re-fit the pin (A) at working height.
COIL10GRH458A0C 4
10. Start the engine and check that the force-feed pres-
sure indicator lights up, then check the oil level in the
reservoir.
11. Bleed the brakes. To do this, leave the engine run-
ning, and then:
• Disengage the parking brake control lever. (lever
forward)
• Open the bleed screw to remove the air.
84490331C 27/03/2014
29.1 [29.218] / 11
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Hydrostatic drive - Pump and motor components
Motor - Remove - Front wheel motor -
9000 L INT --- WE
9040M INT --- WE
NOTE: When removing the hydraulic piping, have a suitable container readily available to capture any residual hy-
draulic oil.
1. Remove the corresponding front wheel. To do this:
• Park on a level surface and apply the parking brake.
• Lower the machine fully using the self-powered de-
vice.
• Engage the backhoe in order to activate the front
yoke. The engine must be stopped.
• Place a suitable jack, approximately 13 t
(28660.09 lb), in the area intended for this purpose
(A), and raise the wheel so it lifts off the ground.
• Remove the wheel.
• Place a cubed wooden block under the strut and re-
move the jack.
• Switch off the ignition.
COIL10GRH465A0B 1
2. Remove the protective housing.
3. Before disconnecting the motor hoses, the drainage
hose at the filter located at the front of the hydraulic
reservoir must be disconnected. This will prevent the
reservoir
from draining (1) Common drain for the two front and
rear left-hand wheel motors.
(2) Front right-hand wheel motor drain.
(3) Rear right-hand wheel motor drain.
COIL10GRH459A0B 2
4. Disconnect and plug all the hoses (4).
5. Remove the fixing screws (5) and take out the motor.
COIL10GRH467A0B 3
ATTENTION: The component weighs approximately 70 kg (154.3 lb). Install a suitable lifting device.
6. Remove the hose installations (6) from the motor and
plug them.
84490331C 27/03/2014
29.1 [29.218] / 12
26. Hydrostatic drive - Pump and motor components
Motor - Install - Front wheel motor -
9000 L INT --- WE
9040M INT --- WE
ATTENTION: The component weighs approximately 70 kg (154.3 lb). Install a suitable lifting device.
1. The left-hand and right-hand motors are identical and
have no specific direction of rotation.
2. Slide the motor (1) into the wheel strut (2) and secure
it using the screws (3). The plate (4) will be placed on
the motor side. The tightening torque of the screws is
200 N·m (1770.1 lb in)
3. Fit the installations (5) and connect the corresponding
hoses (6).
COIL10GRH467A0C 1
4. Before starting the hydraulic motor, its housing must
first be filled. To do this:
• Remove the bleed plug (B) located on the motor
side.
• Fit a manual pump at the end of the drainage hose at
the filter, located at the front of the hydraulic reser-
voir. (see removal instructions) Motor - Remove -
Front wheel motor - (29.218).
• Pump oil into this hose until it runs out of the bleed
hole (B).
• Re-fit the bleed plug (B).
• Remove the pump and connect the drainage hose
(9).
COIL10GRH469A0B 2
5. Place a suitable jack, approximately 13 t (28660.09 lb),
in the area intended for this purpose (A), and raise the
strut to remove the wooden block.
84490331C 27/03/2014
29.1 [29.218] / 13
27. Hydrostatic drive - Pump and motor components
6. Fit the wheel and tighten the nuts (10) to a torque of
420 N·m (3717.3 lb in)
COIL10GRH466A0B 3
7. Start the engine and check that the force-feed pressure
indicator lights up, then check the oil level in the reser-
voir.
8. Fit the protective housing.
84490331C 27/03/2014
29.1 [29.218] / 14
28. Hydrostatic drive - Hydrostatic transmission
Hydrostatic transmission - General specification
9000 L INT --- WE
9040M INT --- WE
NOTE: For the schematic circuit, refer to Rear hydrostatic transmission - Hydraulic schema (29.300)
Hydrostatic system pressures:
During the test, the oil should be at 60 °C inside the tank
Description Values Limiters Pressure gauge position
HP forward travel 505 Bar +/- 5 Bar 11 220
HP reverse travel 505 Bar +/- 5 Bar 12 221
Flow rate counterbalance
in forward travel
480 Bar +/- 5 Bar 13 220
Flow rate counterbalance
in reverse travel
480 Bar +/- 5 Bar 14 221
Boost 33 Bar - 0 Bar + 2 Bar 15 219
Exchange valve 216 Check the flow rate
Brakes 25 Bar +/- 2 Bar To be fitted to the brake line
after the pressure reducer
Right serial line 480 Bar +/- 5 Bar 218 To be fitted to the serial line
Left serial line 480 Bar +/- 5 Bar 217 To be fitted to the serial line
Norias in forward travel 175 Bar +/- 10 Bar 212 151 and use the Noria washing
position
Norias in reverse travel 175 Bar +/- 10 Bar 213 151 and use the Noria washing
position
Diagram of the motor output hydraulic unit
84490331C 27/03/2014
29.2 [29.202] / 3