This document provides instructions for removing and installing the fuel injection pump on a Komatsu WA200-5H or WA200PT-5H wheel loader. The key steps are:
1. Disconnect the fuel lines and electrical connections to the pump.
2. Use a special tool to disconnect the pump drive gear.
3. Remove the pump mounting nuts and bracket to extract the pump from the engine.
Installation is the reverse of removal, taking care to properly align the pump timing pins to the gear. Special tools, torque specifications and an air bleeding procedure are also outlined.
Komatsu d85 px 15 dozer bulldozer service repair manual sn 1001 and upolfjsekdmmes
This document contains information about machine model numbers, engine specifications, safety precautions, and the contents of a shop manual for Komatsu excavators.
It begins with the machine model numbers and engine specifications for D85EX-15 and D85PX-15 excavators. It then provides important safety notices for repair work and general precautions to follow.
The document outlines the contents and organization of the shop manual, including sections on structure and function, testing and adjusting, disassembly and assembly, and others. It explains how to read the manual, with page numbering examples, revision markings, and defined symbols. Hoisting instructions and methods for disconnecting and connecting push-pull type hydraulic couplers are also included.
Komatsu d85 ex 15 dozer bulldozer service repair manual sn 10001 and upeudskkejedmm
This document is a shop manual for the D85EX-15 and D85PX-15 machines. It contains safety precautions and instructions for maintenance, testing, disassembly, and assembly of the machines. The manual is divided into sections covering general information, structure and function, testing and adjusting, disassembly and assembly, and other topics. Technicians are advised to carefully follow the safety notices and use the specified tools and procedures when servicing the machines.
Komatsu d475 a 5 dozer bulldozer service repair manual sn 20001 and upfskkkdjskemd
This shop manual provides information to aid technicians in repairing Komatsu machines. It is divided into sections covering structure, testing, disassembly, and other topics. The manual may contain engine and electrical volumes as well as information on attachments. Safety notices explain precautions for safe work. Technicians should follow all safety procedures, use authorized tools, and consult the most up-to-date information. Symbols mark important safety and technical points. Proper lifting methods are described to prevent injury when hoisting heavy parts. The manual explains different types of push-pull couplers and procedures for disconnecting and connecting hydraulic hoses.
Komatsu wd600 3 wheel dozer service repair manual (sn 50001 and up)ujjjjfkksekmmdm
This 3-sentence summary provides the high-level information from the document:
This shop manual is for the WD600-3 wheel loader and contains instructions for maintenance, repair, and servicing. It includes sections on structure and function, testing and adjusting, disassembly and assembly, maintenance standards, and other technical information. Technicians should carefully follow the safety precautions outlined in the manual when working on the machine.
Komatsu wa250 pt 5 wheel loader service repair manual (sn 70001 and up)ufjjsekkdmmd
This shop manual provides instructions for servicing a Komatsu WA250-5 wheel loader. It begins with safety precautions and general information. It then details the machine's structure, functions, and maintenance standards. Testing and adjusting procedures are outlined, followed by instructions for disassembly, assembly, and repair. The manual is divided into sections covering general topics, structure and function, testing and adjusting, disassembly and assembly, and others. Technicians are advised to follow the manual carefully for safe and effective repairs.
Mc cormick mc series (2002 2007) - mc115 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. The parts include engines, radiators, fans, air cleaners, hydraulic systems, and other components. Each part is listed with an identification number, quantity, and description. Diagrams show the parts and their relation to assemblies.
Mc cormick mc series (2002 2007) - mc95 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. The parts include engines, radiators, fans, air cleaners, hydraulic systems, and other components. Each part is listed with an identification number, quantity, and any applicable component it is attached to.
Mc cormick mc series (2002 2007) - mc105 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. It includes listings and diagrams for engines, radiators, fans, air conditioning components, hydraulic components, and other systems. Each part is listed with an identification code, quantity, and description. Diagrams show the parts and their positions in the various systems.
Komatsu d85 px 15 dozer bulldozer service repair manual sn 1001 and upolfjsekdmmes
This document contains information about machine model numbers, engine specifications, safety precautions, and the contents of a shop manual for Komatsu excavators.
It begins with the machine model numbers and engine specifications for D85EX-15 and D85PX-15 excavators. It then provides important safety notices for repair work and general precautions to follow.
The document outlines the contents and organization of the shop manual, including sections on structure and function, testing and adjusting, disassembly and assembly, and others. It explains how to read the manual, with page numbering examples, revision markings, and defined symbols. Hoisting instructions and methods for disconnecting and connecting push-pull type hydraulic couplers are also included.
Komatsu d85 ex 15 dozer bulldozer service repair manual sn 10001 and upeudskkejedmm
This document is a shop manual for the D85EX-15 and D85PX-15 machines. It contains safety precautions and instructions for maintenance, testing, disassembly, and assembly of the machines. The manual is divided into sections covering general information, structure and function, testing and adjusting, disassembly and assembly, and other topics. Technicians are advised to carefully follow the safety notices and use the specified tools and procedures when servicing the machines.
Komatsu d475 a 5 dozer bulldozer service repair manual sn 20001 and upfskkkdjskemd
This shop manual provides information to aid technicians in repairing Komatsu machines. It is divided into sections covering structure, testing, disassembly, and other topics. The manual may contain engine and electrical volumes as well as information on attachments. Safety notices explain precautions for safe work. Technicians should follow all safety procedures, use authorized tools, and consult the most up-to-date information. Symbols mark important safety and technical points. Proper lifting methods are described to prevent injury when hoisting heavy parts. The manual explains different types of push-pull couplers and procedures for disconnecting and connecting hydraulic hoses.
Komatsu wd600 3 wheel dozer service repair manual (sn 50001 and up)ujjjjfkksekmmdm
This 3-sentence summary provides the high-level information from the document:
This shop manual is for the WD600-3 wheel loader and contains instructions for maintenance, repair, and servicing. It includes sections on structure and function, testing and adjusting, disassembly and assembly, maintenance standards, and other technical information. Technicians should carefully follow the safety precautions outlined in the manual when working on the machine.
Komatsu wa250 pt 5 wheel loader service repair manual (sn 70001 and up)ufjjsekkdmmd
This shop manual provides instructions for servicing a Komatsu WA250-5 wheel loader. It begins with safety precautions and general information. It then details the machine's structure, functions, and maintenance standards. Testing and adjusting procedures are outlined, followed by instructions for disassembly, assembly, and repair. The manual is divided into sections covering general topics, structure and function, testing and adjusting, disassembly and assembly, and others. Technicians are advised to follow the manual carefully for safe and effective repairs.
Mc cormick mc series (2002 2007) - mc115 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. The parts include engines, radiators, fans, air cleaners, hydraulic systems, and other components. Each part is listed with an identification number, quantity, and description. Diagrams show the parts and their relation to assemblies.
Mc cormick mc series (2002 2007) - mc95 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. The parts include engines, radiators, fans, air cleaners, hydraulic systems, and other components. Each part is listed with an identification number, quantity, and any applicable component it is attached to.
Mc cormick mc series (2002 2007) - mc105 tractor service repair manualfjsekkdmmmse
This document contains parts listings and diagrams for various components of McCormick tractors models MC01 through MC95, MC105, and MC115 from 2002 to 2007. It includes listings and diagrams for engines, radiators, fans, air conditioning components, hydraulic components, and other systems. Each part is listed with an identification code, quantity, and description. Diagrams show the parts and their positions in the various systems.
Mc cormick fxl tier 3 (2008 2009) - rp53 - f80 gexl tractor service repair ma...fjsekkdmmmse
This document provides a list of engine components for a Perkins 54.5kw engine. It includes information like part numbers, descriptions, quantities and replacement kits for items like the cylinder block, crankshaft, pistons, cylinder head, valves and other internal engine parts. Measurements and serial number ranges are also provided for some components.
Mc cormick fxl techno tier 3 (2008 2009) - rp54 - f 90 gexl tractor service r...fjsekkdmmmse
This document contains a list of engine components for a Perkins engine. Each component lists information including the part number, quantity needed, reference numbers for assemblies it is part of, and tagging for replacement or service intervals. The components are for items of the engine block, crankshaft, cylinder head, camshaft, and other internal engine parts.
Mc cormick fxl techno tier 3 (2008 2009) - rp54 - f 65 ge tractor service rep...fjsekkdmmmse
This document contains a list of components for an engine assembly along with their part numbers and other identifying information. It includes items like cylinder blocks, heads, pistons, rods, bearings, gears, shafts, plates, bolts, seals, and other engine parts. Each item lists the reference number, quantity needed, and notes whether it is a replacement part or not to be individually serviced. The document provides the specifications for a Perkins diesel engine to allow identification and ordering of replacement components.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f95 fgexl tractor service r...fjsekkdmmmse
This document contains parts lists and repair instructions for engine components. It lists part numbers, descriptions, quantities and repair times for tasks like overhaul, replacement and kit installation. The parts include pistons, rods, bearings, gaskets, valves and other internal engine pieces. Repair steps involve disassembly down to individual parts, inspection, fitting of new or reconditioned pieces and reassembly.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f60 fge tractor service rep...fjsekkdmmmse
This document contains parts lists and technical specifications for components of engines. It includes identification numbers, names and descriptions of engine parts like cylinders, shafts, gears, plates, seals and other items. Quantities and replacement part numbers are provided. The parts are identified as being for Perkins engines that meet Tier 2 emissions standards from 2003 to 2008.
Mc cormick f top restyling (2010 ) - rp55 - f120gexl tractor service repair ...fjsekkdmmmse
This document contains parts listings and component information for various engines and engine parts. It includes listings for engines identified as A, B, C and D that are 81kw, and notes about their tier levels. It also includes listings of individual engine parts like pistons, rods, pumps, sensors and casings, along with reference numbers and specifications. Replacement part numbers and kits are identified.
Mc cormick f top restyling (2010 ) - rp55 - f110gexl tractor service repair ...fjsekkdmmmse
This document provides parts information for various engine components. It lists part numbers, descriptions, reference numbers, and indicates whether items are replacement parts or components of a larger assembly. Quantities and applications are also specified for some parts. The high-level information is that this document contains an exploded parts list and related details for maintenance or repair of engine components.
Mc cormick f top restyling (2010 ) - rp55 - f85ge tractor service repair manualfjsekkdmmmse
This document provides parts information for components of a Perkins 3-cylinder diesel engine. It lists 26 individual parts with identification numbers, names, quantities and other specifications. The parts are for the engine block, cylinder head, pistons, crankshaft and other internal components. It also specifies that the parts are for a McCormick tractor that underwent a restyling between 2010-present.
Mc cormick f top restyling (2010 ) - rp55 - f80 ge xl tractor service repa...fjsekkdmmmse
This document contains parts listings and technical specifications for components of an engine. It includes identification numbers, descriptions, replacement part numbers, and other details for items like cylinders, pistons, gears, shafts and other internal engine parts. Quantities, fit specifications and other assembly information is provided for repair and replacement. The document also indicates application to a specific tractor model range.
Mc cormick f top restyling (2010 ) - rp55 - f70ge tractor service repair manualfjsekkdmmmse
This document provides parts information for components of an engine assembly. It lists part numbers, descriptions, quantities and other technical details for items such as cylinders, pistons, gears, hoses, gaskets and other engine parts. The parts are associated with a Perkins engine model and are replacements for a McCormick tractor from 2010.
Mc cormick f e line restyling (2010- ) - rp56 - f85ge tractor service repair ...fjsekkdmmmse
This document provides parts information for components of an engine. It includes images and part numbers for items like the cylinder block, cylinder head, pistons, connecting rods, camshaft and other internal engine parts. Reference designations and quantities are provided. Notes indicate some parts are only available as replacements and not as individual components.
Mc cormick f e line restyling (2010- ) - rp56 - f80 ge xl tractor service r...fjsekkdmmmse
This document provides parts information for engine components. It lists part numbers, descriptions, and other technical specifications for items like cylinders, pistons, gears, and other internal engine parts. Quantities and applicable serial number ranges are provided for replacement parts. Color codes are also included to identify similar part variants.
This document contains a parts list for the engine and equipment of a Massey Ferguson 7619 tractor, including both AGCO Power SISU engines with E3 Technology and Tier 2 engines. It lists 39 items such as the short block engine, starter motor, fan, cowling, labels, bolts, nuts, and other engine parts. The list provides the part number, quantity, description, and any relevant comments or technical specifications for each part.
This document provides parts information for a Massey Ferguson 7495 tractor engine. It includes 33 numbered items with descriptions of engine parts like the cylinder block, timing gear housing, crankshaft, pistons, and connecting rods. Part numbers, quantities, and serial number ranges or other part identifiers are provided for each item. The document contains notes on the parts and includes diagrams to identify component locations.
This document provides parts information for a Massey Ferguson 7490 tractor engine. It contains 33 sections with details on individual engine parts like the cylinder block, crankshaft, pistons, connecting rods, timing gear housing and other components. Each section lists the part numbers, quantities and descriptions. It also includes footnotes on serial number ranges and other part specifics.
Kubota b2400 hsd tractor parts catalogue manualfjsekkdmmmse
The document provides instructions for parts books. It defines the column headings used on parts number pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent.
Kubota b2150 hsd tractor parts catalogue manualfjsekkdmmmse
This document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and their meanings. The document then provides an example page from the parts book with over 250 individual part listings.
Kubota b2150 e tractor parts catalogue manualfjsekkdmmmse
The document provides instructions and definitions for parts books. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and what they represent. The document then provides an example page from a parts book with over 250 line items categorized by engine, fuel, cooling, electrical and other systems with details for each part.
Komatsu wa200 pt 5l wheel loader service repair manual sna89001 and upfjsekkdmmmse
This document provides instructions for removing and installing the fuel injection pump assembly on a Komatsu WA200-5L or WA200PT-5L wheel loader. The removal process involves disconnecting fuel lines and tubes, removing mounting nuts and bolts, and using a timing pin to match the injection pump timing. Installation is the reverse of removal, and specific tightening torques are provided. Safety precautions are highlighted, including lowering work equipment and disconnecting the battery before starting.
Cub cadet 1529 lawn tractor service repair manualfjsekkdmmmse
This service manual provides instructions for servicing 1000/1500 Series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various engines and drive systems. The manual outlines procedures for removing and replacing components like the hood, fenders, deck, drive belts, brakes, and transaxle. Safety notices advise that the manual is intended for trained technicians experienced with outdoor power equipment.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Mc cormick fxl tier 3 (2008 2009) - rp53 - f80 gexl tractor service repair ma...fjsekkdmmmse
This document provides a list of engine components for a Perkins 54.5kw engine. It includes information like part numbers, descriptions, quantities and replacement kits for items like the cylinder block, crankshaft, pistons, cylinder head, valves and other internal engine parts. Measurements and serial number ranges are also provided for some components.
Mc cormick fxl techno tier 3 (2008 2009) - rp54 - f 90 gexl tractor service r...fjsekkdmmmse
This document contains a list of engine components for a Perkins engine. Each component lists information including the part number, quantity needed, reference numbers for assemblies it is part of, and tagging for replacement or service intervals. The components are for items of the engine block, crankshaft, cylinder head, camshaft, and other internal engine parts.
Mc cormick fxl techno tier 3 (2008 2009) - rp54 - f 65 ge tractor service rep...fjsekkdmmmse
This document contains a list of components for an engine assembly along with their part numbers and other identifying information. It includes items like cylinder blocks, heads, pistons, rods, bearings, gears, shafts, plates, bolts, seals, and other engine parts. Each item lists the reference number, quantity needed, and notes whether it is a replacement part or not to be individually serviced. The document provides the specifications for a Perkins diesel engine to allow identification and ordering of replacement components.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f95 fgexl tractor service r...fjsekkdmmmse
This document contains parts lists and repair instructions for engine components. It lists part numbers, descriptions, quantities and repair times for tasks like overhaul, replacement and kit installation. The parts include pistons, rods, bearings, gaskets, valves and other internal engine pieces. Repair steps involve disassembly down to individual parts, inspection, fitting of new or reconditioned pieces and reassembly.
Mc cormick fxl techno tier 2 (2003 2008) - rp52 - f60 fge tractor service rep...fjsekkdmmmse
This document contains parts lists and technical specifications for components of engines. It includes identification numbers, names and descriptions of engine parts like cylinders, shafts, gears, plates, seals and other items. Quantities and replacement part numbers are provided. The parts are identified as being for Perkins engines that meet Tier 2 emissions standards from 2003 to 2008.
Mc cormick f top restyling (2010 ) - rp55 - f120gexl tractor service repair ...fjsekkdmmmse
This document contains parts listings and component information for various engines and engine parts. It includes listings for engines identified as A, B, C and D that are 81kw, and notes about their tier levels. It also includes listings of individual engine parts like pistons, rods, pumps, sensors and casings, along with reference numbers and specifications. Replacement part numbers and kits are identified.
Mc cormick f top restyling (2010 ) - rp55 - f110gexl tractor service repair ...fjsekkdmmmse
This document provides parts information for various engine components. It lists part numbers, descriptions, reference numbers, and indicates whether items are replacement parts or components of a larger assembly. Quantities and applications are also specified for some parts. The high-level information is that this document contains an exploded parts list and related details for maintenance or repair of engine components.
Mc cormick f top restyling (2010 ) - rp55 - f85ge tractor service repair manualfjsekkdmmmse
This document provides parts information for components of a Perkins 3-cylinder diesel engine. It lists 26 individual parts with identification numbers, names, quantities and other specifications. The parts are for the engine block, cylinder head, pistons, crankshaft and other internal components. It also specifies that the parts are for a McCormick tractor that underwent a restyling between 2010-present.
Mc cormick f top restyling (2010 ) - rp55 - f80 ge xl tractor service repa...fjsekkdmmmse
This document contains parts listings and technical specifications for components of an engine. It includes identification numbers, descriptions, replacement part numbers, and other details for items like cylinders, pistons, gears, shafts and other internal engine parts. Quantities, fit specifications and other assembly information is provided for repair and replacement. The document also indicates application to a specific tractor model range.
Mc cormick f top restyling (2010 ) - rp55 - f70ge tractor service repair manualfjsekkdmmmse
This document provides parts information for components of an engine assembly. It lists part numbers, descriptions, quantities and other technical details for items such as cylinders, pistons, gears, hoses, gaskets and other engine parts. The parts are associated with a Perkins engine model and are replacements for a McCormick tractor from 2010.
Mc cormick f e line restyling (2010- ) - rp56 - f85ge tractor service repair ...fjsekkdmmmse
This document provides parts information for components of an engine. It includes images and part numbers for items like the cylinder block, cylinder head, pistons, connecting rods, camshaft and other internal engine parts. Reference designations and quantities are provided. Notes indicate some parts are only available as replacements and not as individual components.
Mc cormick f e line restyling (2010- ) - rp56 - f80 ge xl tractor service r...fjsekkdmmmse
This document provides parts information for engine components. It lists part numbers, descriptions, and other technical specifications for items like cylinders, pistons, gears, and other internal engine parts. Quantities and applicable serial number ranges are provided for replacement parts. Color codes are also included to identify similar part variants.
This document contains a parts list for the engine and equipment of a Massey Ferguson 7619 tractor, including both AGCO Power SISU engines with E3 Technology and Tier 2 engines. It lists 39 items such as the short block engine, starter motor, fan, cowling, labels, bolts, nuts, and other engine parts. The list provides the part number, quantity, description, and any relevant comments or technical specifications for each part.
This document provides parts information for a Massey Ferguson 7495 tractor engine. It includes 33 numbered items with descriptions of engine parts like the cylinder block, timing gear housing, crankshaft, pistons, and connecting rods. Part numbers, quantities, and serial number ranges or other part identifiers are provided for each item. The document contains notes on the parts and includes diagrams to identify component locations.
This document provides parts information for a Massey Ferguson 7490 tractor engine. It contains 33 sections with details on individual engine parts like the cylinder block, crankshaft, pistons, connecting rods, timing gear housing and other components. Each section lists the part numbers, quantities and descriptions. It also includes footnotes on serial number ranges and other part specifics.
Kubota b2400 hsd tractor parts catalogue manualfjsekkdmmmse
The document provides instructions for parts books. It defines the column headings used on parts number pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent.
Kubota b2150 hsd tractor parts catalogue manualfjsekkdmmmse
This document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and their meanings. The document then provides an example page from the parts book with over 250 individual part listings.
Kubota b2150 e tractor parts catalogue manualfjsekkdmmmse
The document provides instructions and definitions for parts books. It defines column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and what they represent. The document then provides an example page from a parts book with over 250 line items categorized by engine, fuel, cooling, electrical and other systems with details for each part.
Komatsu wa200 pt 5l wheel loader service repair manual sna89001 and upfjsekkdmmmse
This document provides instructions for removing and installing the fuel injection pump assembly on a Komatsu WA200-5L or WA200PT-5L wheel loader. The removal process involves disconnecting fuel lines and tubes, removing mounting nuts and bolts, and using a timing pin to match the injection pump timing. Installation is the reverse of removal, and specific tightening torques are provided. Safety precautions are highlighted, including lowering work equipment and disconnecting the battery before starting.
Cub cadet 1529 lawn tractor service repair manualfjsekkdmmmse
This service manual provides instructions for servicing 1000/1500 Series riding tractors manufactured by MTD Products Inc. It covers a range of models from 2001-2006 with various engines and drive systems. The manual outlines procedures for removing and replacing components like the hood, fenders, deck, drive belts, brakes, and transaxle. Safety notices advise that the manual is intended for trained technicians experienced with outdoor power equipment.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. 00-2 WA200-5H, WA200PT-5H
CONTENTS
No. of page
01 GENERAL ................................................................................................................ 01-1
10 STRUCTURE, FUNCTION AND
MAINTENANCE STANDARD .............................................. 10-1
20 TESTING AND ADJUSTING ...................................................................... 20-1
30 DISASSEMBLY AND ASSEMBLY ..........................................................30-1
90 OTHERS .................................................................................................................... 90-1
3. SAFETY SAFETY NOTICE
00-5
SAFETY
SAFETY NOTICE
IMPORTANT SAFETY NOTICE
Proper service and repair is extremely important for safe machine operation. The service and
repair techniques recommended by Komatsu and described in this manual are both effective
and safe. Some of these techniques require the use of tools specially designed by Komatsu for
the specific purpose.
To prevent injury to workers, the symbol k is used to mark safety precautions in this manual.
The cautions accompanying these symbols should always be followed carefully. If any danger-
ous situation arises or may possibly arise, first consider safety, and take the necessary actions
to deal with the situation.
GENERAL PRECAUTIONS
Mistakes in operation are extremely dangerous.
Read the Operation and Maintenance Manual care-
fully BEFORE operating the machine.
1. Before carrying out any greasing or repairs, read
all the precautions given on the decals which are
fixed to the machine.
2. When carrying out any operation, always
wear safety shoes and helmet. Do not wear
loose work clothes, or clothes with buttons
missing.
• Always wear safety glasses when hitting
parts with a hammer.
• Always wear safety glasses when grinding
parts with a grinder, etc.
3. If welding repairs are needed, always have a
trained, experienced welder carry out the work.
When carrying out welding work, always wear
welding gloves, apron, hand shield, cap and
other clothes suited for welding work.
4. When carrying out any operation with two or
more workers, always agree on the operating
procedure before starting. Always inform your
fellow workers before starting any step of the
operation. Before starting work, hang UNDER
REPAIR signs on the controls in the operator's
compartment.
5. Keep all tools in good condition and learn the
correct way to use them.
6. Decide a place in the repair workshop to keep
tools and removed parts. Always keep the tools
and parts in their correct places. Always keep
the work area clean and make sure that there is
no dirt or oil on the floor. Smoke only in the areas
provided for smoking. Never smoke while work-
ing.
PREPARATIONS FOR WORK
7. Before adding oil or making any repairs, park the
machine on hard, level ground, and block the
wheels or tracks to prevent the machine from
moving.
8. Before starting work, lower blade, ripper, bucket
or any other work equipment to the ground. If
this is not possible, insert the safety pin or use
blocks to prevent the work equipment from fall-
ing. In addition, be sure to lock all the control
levers and hang warning signs on them.
9. When disassembling or assembling, support the
machine with blocks, jacks or stands before
starting work.
10.Remove all mud and oil from the steps or other
places used to get on and off the machine.
Always use the handrails, ladders or steps when
getting on or off the machine. Never jump on or
off the machine. If it is impossible to use the
handrails, ladders or steps, use a stand to pro-
vide safe footing.
4. SAFETY SAFETY NOTICE
00-6
PRECAUTIONS DURING WORK
11.When removing the oil filler cap, drain plug or
hydraulic pressure measuring plugs, loosen
them slowly to prevent the oil from spurting out.
Before disconnecting or removing components
of the oil, water or air circuits, first remove the
pressure completely from the circuit.
12.The water and oil in the circuits are hot when the
engine is stopped, so be careful not to get
burned.
Wait for the oil and water to cool before carry-
ing out any work on the oil or water circuits.
13.Before starting work, remove the leads from the
battery. Always remove the lead from the nega-
tive (–) terminal first.
14.When raising heavy components, use a hoist or
crane.
Check that the wire rope, chains and hooks are
free from damage.
Always use lifting equipment which has ample
capacity.
Install the lifting equipment at the correct places.
Use a hoist or crane and operate slowly to pre-
vent the component from hitting any other part.
Do not work with any part still raised by the hoist
or crane.
15.When removing covers which are under internal
pressure or under pressure from a spring,
always leave two bolts in position on opposite
sides. Slowly release the pressure, then slowly
loosen the bolts to remove.
16.When removing components, be careful not to
break or damage the wiring. Damaged wiring
may cause electrical fires.
17.When removing piping, stop the fuel or oil from
spilling out. If any fuel or oil drips onto the floor,
wipe it up immediately. Fuel or oil on the floor
can cause you to slip, or can even start fires.
18.As a general rule, do not use gasoline to wash
parts. In particular, use only the minimum of
gasoline when washing electrical parts.
19.Be sure to assemble all parts again in their origi-
nal places.
Replace any damaged parts with new parts.
• When installing hoses and wires, be sure
that they will not be damaged by contact
with other parts when the machine is being
operated.
20.When installing high pressure hoses, make sure
that they are not twisted. Damaged tubes are
dangerous, so be extremely careful when install-
ing tubes for high pressure circuits. Also, check
that connecting parts are correctly installed.
21.When assembling or installing parts, always use
the specified tightening torques. When installing
protective parts such as guards, or parts which
vibrate violently or rotate at high speed, be par-
ticularly careful to check that they are installed
correctly.
22.When aligning two holes, never insert your fin-
gers or hand. Be careful not to get your fingers
caught in a hole.
23.When measuring hydraulic pressure, check that
the measuring tool is correctly assembled before
taking any measurements.
24.Take care when removing or installing the tracks
of track-type machines.
When removing the track, the track separates
suddenly, so never let anyone stand at either
end of the track.
5. FOREWORD GENERAL
00-7
FOREWORD
GENERAL
This shop manual has been prepared as an aid to improve the quality of repairs by giving the serviceman an
accurate understanding of the product and by showing him the correct way to perform repairs and make judge-
ments. Make sure you understand the contents of this manual and use it to full effect at every opportunity.
This shop manual mainly contains the necessary technical information for operations performed in a service
workshop. For ease of understanding, the manual is divided into the following chapters; these chapters are fur-
ther divided into the each main group of components.
STRUCTURE AND FUNCTION
This section explains the structure and function of each component. It serves not only to give an under-
standing of the structure, but also serves as reference material for troubleshooting.
In addition, this section may contain hydraulic circuit diagrams, electric circuit diagrams, and mainte-
nance standards.
TESTING AND ADJUSTING
This section explains checks to be made before and after performing repairs, as well as adjustments to
be made at completion of the checks and repairs.
Troubleshooting charts correlating "Problems" with "Causes" are also included in this section.
DISASSEMBLY AND ASSEMBLY
This section explains the procedures for removing, installing, disassembling and assembling each com-
ponent, as well as precautions for them.
MAINTENANCE STANDARD
This section gives the judgment standards for inspection of disassembled parts.
The contents of this section may be described in STRUCTURE AND FUNCTION.
OTHERS
This section mainly gives hydraulic circuit diagrams and electric circuit diagrams.
In addition, this section may give the specifications of attachments and options together.
NOTICE
The specifications contained in this shop manual are subject to change at any time and without any
advance notice. Use the specifications given in the book with the latest date.
6. FOREWORD HOW TO READ THE SHOP MANUAL
00-8
HOW TO READ THE SHOP MANUAL
VOLUMES
Shop manuals are issued as a guide to carrying out
repairs. They are divided as follows:
Chassis volume: Issued for every machine model
Engine volume: Issued for each engine series
Electrical volume:
Attachments volume:
These various volumes are designed to avoid dupli-
cating the same information. Therefore, to deal with
all repairs for any model , it is necessary that chas-
sis, engine, electrical and attachment volumes be
available.
DISTRIBUTION AND UPDATING
Any additions, amendments or other changes will be
sent to KOMATSU distributors. Get the most up-to-
date information before you start any work.
FILING METHOD
1. See the page number on the bottom of the page.
File the pages in correct order.
2. Following examples show how to read the page
number.
Example 1 (Chassis volume):
10 - 3
Item number (10. Structure and
Function)
Consecutive page number for each
item.
Example 2 (Engine volume):
12 - 5
Unit number (1. Engine)
Item number (2. Testing and Adjust-
ing)
Consecutive page number for each
item.
3. Additional pages: Additional pages are indicated
by a hyphen (-) and number after the page
number. File as in the example.
Example:
10-4
10-4-1
10-4-2
10-5
REVISED EDITION MARK
When a manual is revised, an edition mark
((1)(2)(3)....) is recorded on the bottom of the pages.
REVISIONS
Revised pages are shown in the LIST OF REVISED
PAGES next to the CONTENTS page.
SYMBOLS
So that the shop manual can be of ample practical
use, important safety and quality portions are
marked with the following symbols.
Symbol Item Remarks
k Safety
Special safety precautions
are necessary when per-
forming the work.
a Caution
Special technical precau-
tions or other precautions
for preserving standards
are necessary when per-
forming the work.
4 Weight
Weight of parts of sys-
tems. Caution necessary
when selecting hoisting
wire, or when working pos-
ture is important, etc.
3
Tightening
torque
Places that require special
attention for the tightening
torque during assembly.
2 Coat
Places to be coated with
adhesives and lubricants,
etc.
5 Oil, water
Places where oil, water or
fuel must be added, and
the capacity.
6 Drain
Places where oil or water
must be drained, and
quantity to be drained.
}Each issued as one
volume to cover all
models
12-203
12-203-1
12-203-2
12-204
Added pages
7. 30-16 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
REMOVAL AND INSTALLATION OF
FUEL INJECTION PUMP
ASSEMBLY
SPECIAL TOOLS
REMOVAL
kLower the work equipment to the ground and stop
the engine.
kDisconnect the cable from the negative (–) termi-
nal of the battery.
1. Open the engine right side cover.
2. Disconnect fuel control cable (1) from the fuel
injection pump.
[*1]
3. Disconnect fuel supply hoses (2) and (3).
4. Disconnect fuel filter (4).
5. Disconnect fuel return hose (5).
6. Remove 6 fuel injection tubes (6).[*2]
7. Disconnect engine stop solenoid terminals PULL
(7), HOLD (8), and GND (9).
8. Remove cotter pin (10) and nut (11), and then
remove engine stop solenoid rod (12) from the
fuel injection pump.
9. Remove engine stop solenoid (13) and bracket
(14) together.
[*3]
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
A1 795-799-1390 Remover t 1
8. WA200-5H, WA200PT-5H 30-17
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
10. Remove fuel tubes (15) and (16).
[*4]
11. Remove lubrication tubes (17) and (18).
12. Remove boost compensator tube (19).
13. Using timing pin (20), match the timing gear to the
fuel injection timing.
a For details, see TESTING AND ADJUSTING,
Testing and adjusting fuel injection timing.
14. Remove cap (21).
a Use a filter wrench, etc. to remove the cap.
15. Remove fuel injection pump nut (22) and washer
(23).
a Take care not to drop the nut and washer into
the case.
16. Using tool A1, disconnect the fuel injection pump
shaft and pump drive gear.
9. 30-18 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
17. Remove fuel injection pump bracket (24).
18. Remove 4 fuel injection pump mounting nuts (25)
and fuel injection pump assembly (26).
[*5]
INSTALLATION
• Carry out installation in the reverse order to
removal.
[*1]
a Adjust the fuel control cable. For details, see
TESTING AND ADJUSTING, Measuring, testing
operating force of accelerator pedal.
[*2]
3 Fuel injection tube nut
(on injection pump side):
24 ± 4 Nm {2.45 ± 0.41 kgm}
Fuel injection tube nut
(on nozzle holder side):
30 ± 5 Nm {3.06 ± 0.51 kgm}
[*3]
3 Engine stop solenoid bracket mounting nut:
14 – 21 Nm {1.4 – 2.1 kgm}
a Adjust the engine stop solenoid. For details, see
TESTING AND ADJUSTING, Adjusting engine
stop solenoid.
[*4]
3 Fuel tube joint bolt (on fuel filter side):
19.6 – 29.4 Nm {2.0 – 3.0 kgm}
[*5]
a Install the fuel injection pump assembly according
to the following procedure.
1. Ensure that the drive gear is fixed to the fuel
injection timing using timing pin (20).
10. WA200-5H, WA200PT-5H 30-19
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
2. Remove plug (27) from the fuel injection pump,
turn over timing pin (28), and re-install the plug
into the fuel injection pump.
a Ensure that the cut-out portion of the timing
pin engages the protruding portion in the
pump.
a If you cannot insert the timing pin, injection
timing is not right. Make an adjustment.
(See TESTING AND ADJUSTING, Testing
and adjusting fuel injection timing.)
3. Install fuel injection pump assembly (26), and
ensure it with 4 nuts (25).
3 Fuel injection pump mounting nuts:
9.8 ± 2 Nm {1.0 ± 0.2 kgm}
4. Install fuel injection pump bracket (24).
3 Fuel injection pump bracket mounting
bolt (Injection pump side):
22 ± 2 Nm {2.2 ± 0.2 kgm}
5. Install washer (23) and tighten fuel injection pump
nut (22) temporarily.
a When installing, be careful not to drop nuts or
washers in the case.
kTighten the nut temporarily with the following
tightening torque so that you do not damage
the timing pin.
3 Fuel injection pump nut temporary tight-
ening torque:
12.5 ± 2.5 Nm {1.27 ± 0.25 kgm}
11. 30-20 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY FUEL INJECTION PUMP
6. Pull timing pin (20) on the timing gear side and
restore it to its original position.
7. Tighten fuel injection pump nut (22) securely.
3 Fuel injection pump nut secure tightening
torque: 95 ± 10 Nm {9.7 ± 1.01 kgm}
kBefore starting the engine, double-check that
you returned drive gear timing pin (20) and
fuel injection pump timing pin (28) to their
original position.
• Bleeding air
Bleed air from the fuel system using the following
procedure.
1. Fill the fuel tank and bring the fuel gauge to FULL
position.
2. Loosen air bleeding plug (29).
3. Remove cap (30).
4. Loosen the knob of feed pump and move it up
and down, so that the fuel overflow until no more
bubbles come out from the air bleeding plug
mounting section.
a Wipe out fuel from the engine completely with
rag.
5. Tighten air bleeding plug (29).
3 Air bleeding plug:
7.8 – 11.8 Nm {0.8 – 1.2 kgm}
6. Push the feed pump knob and tighten it.
7. Start the engine, and check that there is no leak
from the fuel system.
12. WA200-5H, WA200PT-5H 30-21
DISASSEMBLY AND ASSEMBLY NOZZLE HOLDER
REMOVAL AND INSTALLATION OF
NOZZLE HOLDER ASSEMBLY
SPECIAL TOOLS
REMOVAL
kLower the work equipment to the ground and stop
the engine.
1. Open the engine right and left side covers.
2. Remove fuel injection tubes (1).
[*1]
3. Remove spill tube (2).
[*2]
4. Loosen and remove nozzle holder assembly (3).
[*3]
a Take care that dirt and foreign matter will not
enter the mounting part of the nozzle holder
assembly
a If the nozzle holder is difficult to remove, use
tool A3.
INSTALLATION
• Carry out installation in the reverse order to
removal.
[*1]
3 Fuel injection tube nut (on injection pump side):
24 ± 4 Nm {2.45 ± 0.41 kgm}
Fuel injection tube nut (on nozzle holder side):
30 ± 5 Nm {3.06 ± 0.51 kgm}
[*2]
3 Spill tube joint bolt: 9 Nm {0.9 kgm}
[*3]
3 Nozzle holder: 60 Nm {6.1 kgm}
• Bleeding air
Bleed air from the fuel system. See Removal and
installation of fuel injection pump assembly.
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
A 3 795-799-1171 Puller t 1
13. 30-22 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
REMOVAL AND INSTALLATION OF
CYLINDER HEAD ASSEMBLY
SPECIAL TOOLS
REMOVAL
kStop the machine on a level place and set the
safety bar to the frame.
kLower the work equipment to the ground, stop the
engine, apply the parking brake, and put chocks
under the tires.
kDisconnect the cable from the negative (–) termi-
nal of the battery.
1. Remove engine assembly. For details, see
Removal and Installation of engine assembly.
2. Drain the coolant.
6 Coolant: 17 l
3. Remove the air conditioner compressor accord-
ing to the following procedure.
1) Disconnect wiring connector E16 (1) and
ground terminal E22 (2).
2) Remove cover (3).
3) Loosen 2 mounting bolts (4) and 2 mounting
bolts (5).
4) Loosen 2 locknuts (6) and 2 adjustment bolts
(7).
5) Remove air conditioner compressor belt (8).
[*1]
6) Remove 2 mounting bolts (4), 2 mounting
bolts (5), and air conditioner compressor and
bracket assembly (10).
a Place the air conditioner piping by the
side of the engine without disconnecting
it.
4. Disconnect the following wiring connectors and
terminals.
a Disconnect the wiring harness clamps, too.
(11): PULL
(12): HOLD
(13): GND
(14): E14
(15): E09
5. Remove the mounting bolts of heater relay (16).
Symbol
Part No. Part Name
Necessity
Q'ty
New/remodel
Sketch
A
3 795-799-1171 Puller t 1
4 790-331-1110 Wrench t 1
14. WA200-5H, WA200PT-5H 30-23
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
6. Remove air hose (17) between the air cleaner
and turbocharger.
[*2]
7. Disconnect radiator inlet hose (18).
[*3]
8. Disconnect aftercooler upper hose (19).
[*4]
9. Remove air cleaner and bracket assembly (20).
10. Remove the muffler according to the following
procedure.
1) Remove mounting bolts (21), 2 pieces on
each side.
2) Remove 1 mounting bolt (22).
3) Remove 4 mounting bolts from the inside of
rear side a.
4) Raise muffler (23) and disconnect drain tube
(24).
15. 30-24 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
11. Remove the turbocharger and exhaust manifold
assembly according to the following procedure.
1) Disconnect turbocharger lubrication tubes
(25) and (26).
[*5]
2) Remove bracket (27).
3) Remove bracket (28).
4) Remove muffler drain tube mounting bolt
(29).
5) Remove exhaust manifold heat insulation
cover (30).
6) Remove muffler brackets (31).
7) Lift off turbocharger and exhaust manifold
assembly (32).
[*6]
4 Turbocharger and exhaust manifold
assembly: 40 kg
12. Remove 6 fuel injection tubes (33).
[*7]
16. WA200-5H, WA200PT-5H 30-25
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
13. Remove alternator belt cover (34).
14. Disconnect wiring connectors E02 (35) and termi-
nal E11 (36).
15. Remove mounting bolts (37), (38) and alternator
(39).
16. Remove alternator bracket (40).
17. Remove engine sling and thermostat housing
assembly (41).
[*8]
18. Remove air conditioner compressor bracket (42).
19. Remove engine stop solenoid bracket mounting
bolts and nuts (43).
[*9]
20. Disconnect air hose (44).
[*10]
21. Remove air intake connector (45) and heater
(46).
17. 30-26 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
22. Remove boost compensator tube (47).
23. Remove fuel tubes (48) and (49).
24. Remove fuel filter (50).
25. Disconnect spill hose (51).
26. Disconnect heater hose (52).
27. Remove spill tube (53).
28. Remove 6 nozzle holders (54).
[*11]
a If the nozzle holder is difficult to remove, use
tool A3.
29. Remove 6 cylinder head covers (55).
[*12]
18. WA200-5H, WA200PT-5H 30-27
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
30. Remove rocker arm (56).
[*13]
a Loosen the locknut, and then loosen adjust-
ment screw by 2 – 3 turns.
31. Remove push rods (57).
[*14]
32. Lift off cylinder head assembly (58).
[*15]
4 Cylinder head assembly: 55 kg
33. Remove cylinder head gasket (59).
[*16]
INSTALLATION
• Carry out installation in the reverse order to
removal.
[*1]
a Adjust the tension of the air conditioner compres-
sor belt. For details, see TESTING AND
ADJUSTING, Testing and adjusting air condi-
tioner compressor belt tension.
[*2]
3 Air hose clamp:
9.8 ± 0.5 Nm {1.0 ± 0.05 kgm}
[*3]
2 Mating face of hose: Gasket sealant
(ThreeBond 1208E or equivalent)
3 Radiator hose clamp:
10.5 ± 0.5 Nm {107 ± 5 kgcm}
[*4]
3 Aftercooler hose clamp:
10.5 ± 0.5 Nm {107 ± 5 kgcm}
[*5]
3 Mounting nut of turbocharger lubrication tube
(25): 35 ± 5 Nm {3.57 ± 0.51 kgm}
Mounting bolt of turbocharger lubrication tube
(26): 24 ± 4 Nm {2.45 ± 0.41 kgm}
[*6]
a Tighten the exhaust manifold mounting bolts in 3
times according to the following procedure.
3 Exhaust manifold mounting bolt:
1st time: Tighten the bolts to 24 ± 4 Nm {2.45
± 0.41 kgm} in the order of 1 – 12.
2nd time: Tighten the bolts to 43 ± 6 Nm {4.38
± 0.61 kgm} in the order of 1 – 12.
3rd time: Tighten the bolts to 43 ± 6 Nm {4.38
± 0.61 kgm} in the order of 1 – 4.
19. 30-28 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
[*7]
3 Fuel injection tube nut (on injection pump
side): 24 ± 4 Nm {2.45 ± 0.41 kgm}
Fuel injection tube nut (on nozzle holder
side): 30 ± 5 Nm {3.06 ± 0.51 kgm}
[*8]
3 Thermostat housing mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
[*9]
3 Engine stop solenoid bracket mounting nut:
14 – 21 Nm {1.4 – 2.1 kgm}
[*10]
3 Air hose clamp: 8.8 ± 0.5 Nm {90 ± 5 kgcm}
[*11]
3 Nozzle holder: 60 Nm {6.1 kgm}
[*12]
3 Cylinder head cover mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
[*13][*14][*15][*16]
a Install the rocker arm assembly and cylinder head
assembly according to the following procedure.
a Check that there is not dirt or foreign matter on
the mounting face of the cylinder head or in the
cylinder.
1. Set cylinder head gasket (59) to the cylinder
block.
a Check that the gasket is matched to the hole
of the block.
2. Sling cylinder head assembly (58) and set it to the
cylinder block.
3. Tighten the cylinder head bolts in 3 times in the
order shown in the following figure.
5Threads and seat of mounting bolt: Engine oil
3 Cylinder head bolt:
1st time: Tighten the bolts to 90 ± 5 Nm
{9.18 ± 0.51 kgm} in the order
of 1 - 26.
2nd time: Tighten the bolts to 120 ± 5 Nm
{12.24 ± 0.51 kgm} in the order
of 3, 6, 11, 14, 19, and 22.
3rd time:
• When using tool A4
Using angle tightening wrench A4,
retighten them 90° ± 5°. (Angle tight-
ening)
20. WA200-5H, WA200PT-5H 30-29
DISASSEMBLY AND ASSEMBLY CYLINDER HEAD
• When not using tool A4
Make marks on bolts and cylinder
heads as shown in a, and retighten
them by the angle of b (90° ± 5°).
(Angle tightening)
4. Install push rod (57).
a Lubricate the push rod section with engine
oil.
5. Install rocker arm assembly (56), and tighten the
mounting bolts with fingers.
a Ensure that the ball of the adjustment screw
is fitted to the socket of push rod (57).
a Lubricate the thread portion and seat surface
of bolts with 8 mm diameter and bolts with 12
mm diameter with engine oil.
6. Tighten rocker arm assembly mounting bolts (8
mm diameter).
3 Rocker arm mounting bolt:
24 ± 4 Nm {2.45 ± 0.41 kgm}
7. Adjust the engine stop solenoid. For details, see
TESTING AND ADJUSTING, Adjusting valve
clearance.
• Refilling with water
Add water through the water filler to the specified
level. Run the engine to warm the water. Then,
check the water level again.
• Bleeding air
Bleed air from the fuel system. See Removal and
installation of fuel injection pump assembly.
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. 30-30 WA200-5H, WA200PT-5H
DISASSEMBLY AND ASSEMBLY ENGINE
REMOVAL AND INSTALLATION OF
ENGINE
REMOVAL
kStop the machine on a level place and set the
safety bar to the frame.
kLower the work equipment to the ground, stop the
engine, apply the parking brake, and put chocks
under the tires.
kDisconnect the cable from the negative (–) termi-
nal of the battery.
1. Drain the coolant.
6 Coolant: 17 l
2. Remove the engine hood assembly according to
the following procedure.
1) Remove left and right fenders (1).
2) Remove covers (2), (3), and (4).
3) Remove pre-cleaner (5).
[*1]
4) Remove cover (6).
5) Remove air hose (7) between the air cleaner
and turbocharger.
a This is to obtain the place to secure the
air conditioner condenser.
6) Disconnect wiring connector BL1 (8) and har-
ness clamp to the left rear of the operator
cab.
7) Disconnect the 2 window washer hoses (9) at
the right front of the engine hood.
23. WA200-5H, WA200PT-5H 30-31
DISASSEMBLY AND ASSEMBLY ENGINE
8) Disconnect wiring connector B04 (10) for air
conditioner condenser.
9) Remove 2 clamps (11) for the receiver tank
hose.
10) Remove 2 U-bolts (12).
a While removing the air conditioner con-
denser, fix the receiver tank to the side of
the engine along with the air conditioner
condenser with a rope or something.
11) Remove air conditioner condenser mounting
bolts (13), 2 pieces on each side.
a With the air conditioner piping connected,
move the air conditioner condenser to the
engine and fix it with a rope or some-
thing.
12) Remove 4 mounting bolts (15) of cover (14).
13) Disconnect reservoir tank hose (16).
14) Remove grille (17), and remove fan guard
(18).