This document provides instructions for removing a transmission from TM110319 tractors. It describes disconnecting various lines, hoses, wiring and other components to fully separate the transmission from the engine and mid-frame. Key steps include using a splitting stand to support the engine and mid-frame while removing cap screws, then lifting the transmission out using a transmission lifting fixture once it is fully disconnected. Precautions are noted to properly support the tractor and avoid collapsing the splitting stand during the removal process.
John deere 8260 r tractors service repair technical manual (tm110319)ujfjjdkkkkmm
This document provides instructions for removing a transmission from TM110319 tractors. It describes disconnecting various lines, hoses, wiring and other components to fully separate the transmission from the engine and mid-frame. Key steps include using a splitting stand to support the engine and mid-frame while removing cap screws, then carefully rolling the front of the tractor forward to allow removal of the transmission using a lifting fixture. Precautions are noted to properly support the vehicle and avoid injury during the process.
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere 8260 r tractors service repair technical manual (tm110319)ujfjjdkkkkmm
This document provides instructions for removing a transmission from TM110319 tractors. It describes disconnecting various lines, hoses, wiring and other components to fully separate the transmission from the engine and mid-frame. Key steps include using a splitting stand to support the engine and mid-frame while removing cap screws, then carefully rolling the front of the tractor forward to allow removal of the transmission using a lifting fixture. Precautions are noted to properly support the vehicle and avoid injury during the process.
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
Caterpillar cat 323 d ln excavator (prefix sed) service repair manual (sed000...fjjskekdmmme
This document provides instructions for removing and installing piston cooling jets on a Caterpillar C6.4 engine. The procedure involves removing the oil pan, then removing each jet one by one using a 46 mm socket to rotate the engine. For installation, the jets are reinstalled and tightened to a specified torque, again using the socket to rotate the engine for access. Safety notices are provided to keep parts clean and prevent contamination.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjskekdmmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d ln excavator (prefix cyd) service repair manual (cyd000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Reassembling follows the reverse order, including pressing bearings into housings and using shims to set proper bearing preload.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix pbm) service repair manual (pbm0000...fjjskekdmmme
The document provides instructions for removing and installing a crankshaft on a 323D L Excavator. It describes:
1. Removing the front housing, rear seal, flywheel housing and oil pan before removing the crankshaft.
2. Using a socket and lifting straps to remove the crankshaft, which weighs 84-99 kg.
3. Checking crankshaft end play and installing in reverse order of removal, ensuring proper bearing installation and torque of bolts.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjskekdmmme
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and driver group to re-install these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
Caterpillar cat 323 d ln excavator (prefix sed) service repair manual (sed000...fjjskekdmmme
This document provides instructions for removing and installing piston cooling jets on a Caterpillar C6.4 engine. The procedure involves removing the oil pan, then removing each jet one by one using a 46 mm socket to rotate the engine. For installation, the jets are reinstalled and tightened to a specified torque, again using the socket to rotate the engine for access. Safety notices are provided to keep parts clean and prevent contamination.
Caterpillar cat 323 d ln excavator (prefix rac) service repair manual (rac000...fjjskekdmmme
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d ln excavator (prefix cyd) service repair manual (cyd000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Reassembling follows the reverse order, including pressing bearings into housings and using shims to set proper bearing preload.
Caterpillar cat 323 d l excavator (prefix ysd) service repair manual (ysd0000...fjjskekdmmme
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C6.4 engine. It lists the required tools and presents a step-by-step procedure that includes removing bolts and washers, lifting the housing off using a bracket and lifting device, removing the oil seal, cleaning surfaces, installing a new gasket and seal, and securing the housing back in place.
Caterpillar cat 323 d l excavator (prefix pbm) service repair manual (pbm0000...fjjskekdmmme
The document provides instructions for removing and installing a crankshaft on a 323D L Excavator. It describes:
1. Removing the front housing, rear seal, flywheel housing and oil pan before removing the crankshaft.
2. Using a socket and lifting straps to remove the crankshaft, which weighs 84-99 kg.
3. Checking crankshaft end play and installing in reverse order of removal, ensuring proper bearing installation and torque of bolts.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjskekdmmme
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and driver group to re-install these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Annual report on mahindra and mahindra on supply chain analysisdf
John deere 8285 r tractors service repair technical manual (tm110319)
1. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Specifications
Specifications
Item Measurement Specification
Transmission-to-Mid-Frame Cap
Screws
Torque 430 N·m
(317 lb.-ft.)
Transmission-to-Engine Cap Screws Torque 500 N·m
(369 lb.-ft.)
Auxiliary Drive Support-to-
Transmission Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Engine-to-Transmission Drive Shaft
Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Universal Joint Cap Screws-to-
Differential Yoke
Torque 150 N·m
(110 lb.-ft.)
Scavenge Pump-to-Manifold Cap
Screws
Torque 125 N·m
(92 lb.-ft.)
Scavenge Pump Seal Depth 0.5 mm
(0.020 in.)
Auxiliary Drive Shaft Cap Screws Torque 80 N·m
(59 lb.-ft.)
LN71218,0000554-19-20120712
1/1
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
2. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors Repair (S. N. —090000) (Russia S. N.
052201—055000)
Remove Transmission
Remove Transmission
RXA0119494-UN: Shield and Tool Box
LEGEND:
A - Shield
B - Step
C - Tool Box
D - Battery Cover
1. Position hood forward. (See Optional Forward Hood Position in Section 80, Group 05.)
2. Discharge air conditioning system. (See Discharge Air Conditioning System in Section 90, Group 10.)
3. Drain coolant from engine block and radiator.
4. Remove shield (A) and step (B).
5. Remove tool box (C) and battery cover (D).
6.
RXA0119496-UN: Battery Ground Cable
LEGEND:
A - Battery Ground Cable
B - Batteries (2 used)
C - Single Point Ground
Disconnect battery ground cable (A) from batteries (B) and from single point ground (C).
7.
RXA0119500-UN: Left-Hand Hood Spreader
1/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
3. RXA0119501-UN: Right-Hand Hood Spreader
LEGEND:
A - Hood Spreaders (2 used)
Remove hood spreaders (A).
8.
RXA0119553-UN: Positive Battery Cable
LEGEND:
A - Clamps (4 used)
B - Positive Battery Cable
Remove clamps (A) and positive battery cable (B).
9. Remove front weights, if equipped.
10. For tractors with Front Hitch: Remove front hitch. (See Remove and Install Front 3-Point Hitch in Section 70, Group 35.)
11. For tractors with Front PTO: Remove front PTO. (See Remove Front PTO in Section 56, Group 40.)
12.
RXA0109012-UN: Transmission Drain Plug
LEGEND:
A - Plug
B - Front Plate
Drain transmission by removing plug (A). (See Drain Hydraulic System in Section 70, Group 05.)
13. Remove access plate (B).
14. If equipped, remove radar sensor. (See Replace Radar Sensor in Section 40, Group 30.)
15. NOTE:
2/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
4. RXA0107812-UN: Left-Hand Side
RXA0107814-UN: Right-Hand Side
LEGEND:
A - Lines (5 used)
B - Clamp
Some lines use Snap-To-Connect fittings. (See Servicing and Connecting Snap-To-Connect STC™ Fittings in Section 10, Group 10.)
Line and hose configurations vary depending on tractor options.
Disconnect lines (A).
16. Cap and plug lines and ports to prevent contamination.
17. Remove clamp (B).
18.
RXA0107813-UN: Bottom of Transmission
RXA0107811-UN: Bottom of Transmission
LEGEND:
A - Transmission Lines (6 used)
Disconnect transmission lines (A).
19. Cap and plug lines and ports to prevent contamination.
3/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
5. 20.
RXA0125922-UN: Snap Ring and Line Clamp
LEGEND:
A - Snap Ring
B - Clamp
For tractors equipped with MFWD, perform the following:
a. Loosen MFWD drive shaft shield and remove steering line clamp (B).
b.
CAUTION:
Tractor ignition must be in the "OFF" position when checking position of MFWD drive shaft snap ring (A).
Position tractor with MFWD drive shaft snap ring (A) in downward position.
c. Disengage MFWD shaft snap ring and slide shaft forward to disengage from MFWD clutch.
21.
RXA0056006-UN: Drive Shaft
LEGEND:
A - Drive Shaft Universal Joint
For tractors with ILS™: Disconnect one drive shaft universal joint (A) from differential yoke and support drive shaft on lower control arm.
22.
RXA0111687-UN: Shield and Exhaust
LEGEND:
A - Shield
B - Exhaust Pipe
Remove shield (A).
23. Remove exhaust pipe (B). (See Service Exhaust System in Section 30, Group 25.)
4/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
6. 24.
RXA0111469-UN: Cab Riser Panel
RXA0111467-UN: Air Conditioner Lines
LEGEND:
A - Cab Riser Panel
B - Cap Screws (2 used)
C - Line Clamp
D - Air Conditioning Line (High Pressure)
E - Air Conditioning Line (Low Pressure)
Remove cab riser panel (A) by removing cap screws (B) under floor mat.
25. Remove line clamp (C).
26. Disconnect and plug air conditioner lines (D and E).
27.
RXA0119554-UN: Alternator
LEGEND:
A - Auxiliary Drive Belt
B - Alternator Wires (3 used)
C - Mounting Cap Screws (2 used)
D - Alternator
Remove auxiliary drive belt (A).
28. Identify, label, and disconnect alternator wires (B).
29. Remove mounting cap screws (C) and alternator (D).
5/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
7. 30.
RXA0119555-UN: Fan Drive Control Valve
LEGEND:
A - Fan Drive Control Valve
B - Line
C - Lines (2 used)
D - Cap Screws (2 used)
Identify, label, and disconnect harness from fan drive control valve (A).
31. Remove line (B).
32. Disconnect lines (C).
33. Cap and plug lines and ports to prevent contamination.
34. Remove cap screws (D) and fan drive control valve.
35.
RXA0119556-UN: Steering Lines and Vent Hose
LEGEND:
A - Steering Lines (2 used)
B - Vent Hose
Disconnect steering lines (A).
36. Disconnect vent hose (B).
37.
RXA0119557-UN: Heater Hoses
LEGEND:
A - Heater Hoses (2 used)
Remove heater hoses (A).
6/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
8. 38.
RXA0119558-UN: Fuel Return and Fan Drive Supply
LEGEND:
A - Fuel Return Line
B - Fan Drive Supply Line
Disconnect fuel return hose (A).
39. Disconnect fan drive supply line (B).
40. Cap and plug lines to prevent contamination.
41.
RXA0119560-UN: Fuel Supply Line
LEGEND:
A - Cap Screws (2 used)
B - Fuel Supply Line
Remove cap screws (A).
42. Remove fuel supply line (B).
43.
RXA0119561-UN: Oil Cooler Lines
LEGEND:
A - Oil Cooler Lines (2 used)
B - Air Line
Disconnect oil cooler lines (A).
44. For tractors equipped with Air Trailer Brakes: Remove air line (B).
45.
7/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
9. RXA0119562-UN: Harness
LEGEND:
A - Connectors (3 used)
B - Cap Screw, Clamp, and Ground Wires
C - Cap Screw
Disconnect harness connectors (A).
46. Remove cap screw, clamp, and ground wires (B).
47. Remove filter housing bracket cap screw (C).
48.
RXA0119559-UN: Auxiliary Drive Bracket
LEGEND:
A - Cap Screw
B - Cap Screws (4 used)
Remove filter housing bracket cap screw (A).
49. Remove auxiliary drive bracket cap screws (B).
50.
RXA0077936-UN: Wiring Connector
LEGEND:
A - Shield
B - Wiring Connector (4 used)
C - Harness Clamps (2 used)
D - Harness
Remove shield (A).
51. Disconnect wiring connectors (B) and remove harness (D) from harness clamps (C).
52. IMPORTANT:
RXA0080844-UN: Left-Hand Transmission Connectors
8/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
10. RXA0080846-UN: Right-Hand Transmission Connectors
RXA0080849-UN: Lower Half Transmission Connectors
LEGEND:
A - Solenoids (13 used)
B - Sensors (5 used)
C - Harness
D - Clamps (6 used)
Note harness routing and retention. Identify and label connectors for reassembly.
Identify, label, and disconnect solenoid (A) and sensor (B) connectors from transmission.
53. Note harness routing and remove harness (C) from clamps (D).
54. Move harness from mid frame to avoid damage to harness.
55.
RXA0078566-UN: Drive Shaft
LEGEND:
A - JDG861 Torque Wrench Adapter
Disconnect drive shaft using JDG820 Flywheel Rotation Tool and JDG861 Torque Wrench Adapter (A).
56.
CAUTION:
Stand may collapse and cause injury or death if pins are not installed correctly on stand. Each tube on the stand must be pinned together with another tube. One
pin may pass through all three tubes, or each pin may pass through two tubes depending on the tire size.
IMPORTANT:
9/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
11. Use only stands specified for stability when splitting the tractor.
RXA0079554-UN: Splitting Stand
RXA0079555-UN: Splitting Stand for ILS™
LEGEND:
A - JT07122-6 Rear Adapter Plates
B - JT07122-1 Splitting Stand
C - JDG2061 Front Adapter
D - JT07321 Rear Support Wheels
E - JT07122-7-1 Cross Member
F - JT07122-7-2 Upright Supports
For ALL tractors, perform the following steps: Install JT07122-6 Rear Adapter Plates (A) on JT07122 Splitting Stand (B). DO NOT tighten cap screws.
57. Install JDG2061 Front Adapter (C) on JT07122 Splitting Stand. Tighten cap screws.
58. IMPORTANT:
Front adapter (C) must be installed tight against plate on top of splitting stand to fit correctly on tractor.
NOTE:
JT07122-7-1 Cross Member and JT07122-7-2 Upright Supports are part of JT07122-7 Upright Supports .
Install JT07122-7-1 Cross Member (E). DO NOT tighten cap screws.
59. Install JT07321 Rear Support Wheels (D). DO NOT tighten cap screws.
60. DO NOT install JT07122-7-2 Upright Supports (F) at this time.
61.
RXA0079556-UN: Rear Splitting Stand
10/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
12. RXA0077253-UN: Front Support
LEGEND:
A - Cap Screws
B - Front Support
C - Front Frame Member
D - Locating Block
Install rear splitting stand on front of mid-frame using cap screws (A). Tighten all cap screws.
62. Adjust splitting stand wheels to properly support tractor.
63. NOTE:
Depending on tractor configuration, front tires will need removed, JDG2061 Front Adapter installed, and front tires installed. (For further information on removing and
installing front tires, see Operator’s Manual.)
Install JDG2061 Front Adapter so front support (B) is tight under front frame member (C) and locating blocks (D) are between front frame member.
64. For tractors with ILS™: Bleed off suspension system. (See Relieve System Pressure—ILS™ in Section 58, Group 05.)
65. NOTE:
RXA0119743-UN: Right-Hand Side
11/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
13. RXA0119744-UN: Left-Hand Side
LEGEND:
A - JT07122-7-2 Upright Supports (2 used)
B - Cap Screws (4 used)
JT07122-7-2 Upright Supports are part of JT07122-7 Upright Supports .
Install JT07122-7-2 Upright Supports (A) on front splitting stand.
66. Attach upright supports to engine block with cap screws (B).
67. Tighten cross-member cap screws.
68.
RXA0119757-UN: JDG1935 Auxiliary Drive Support
LEGEND:
A - JDG1935 Auxiliary Drive Support
B - Upright Support
C - Cap Screws (2 used)
D - Bracket
E - Lifting Screw
F - Cap Screws (10 used MFWD and 2WD) (16 used ILS)
Install JDG1935 Auxiliary Drive Support (A) to left-hand upright support (B).
69. Attach support (A) to auxiliary drive with cap screws (C).
70. Position bracket (D) under air cleaner and attach to support (A).
71. NOTE:
Use a prybar to assist lifting of auxiliary drive housing off dowel pins
Turn lifting screw (E) to lift auxiliary drive and air cleaner off transmission dowel pins.
72. Lower rear wheel of splitting stand so rear of engine is correctly supported.
73. Remove front frame-to-transmission cap screws (F) from both sides.
74.
CAUTION:
Avoid possible personal injury. DO NOT remove transmission-to-mid-frame cap screws. Doing so will collapse the splitting stand. Remove ONLY the front frame-
to-transmission cap screws.
Carefully roll front of tractor forward approximately 250—300 mm (10—12 in.).
12/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
14. 75.
RXA0104303-UN: JT07201A Transmission Lifting Fixture and Adapter
LEGEND:
A - JT07201A Transmission Lifting Fixture
B - Cap Screw
C - JDG1883 Adapter
Drill hole in JT07201A Transmission Lifting Fixture (A). (See DFRW210—Hole Drilled in JT07201 in Section 99, Group 05.)
76. Insert JDG1883 Transmission Lifting Fixture Adapter (C) and attach with cap screw (B).
77.
RXA0104302-UN: Transmission Lifting Fixture
LEGEND:
A - Cap Screw
B - MFWD and ILS Line
C - 2WD Line
Loosen cap screw (A) on JT07201A Transmission Lifting Fixture .
78. Align center of cap screw with line (B) for MFWD and ILS™, or line (C) for tractors with 2WD.
79. Tighten cap screw (A).
80.
RXA0119758-UN: Three Cap Screws
RXA0119759-UN: JT07201 Transmission Lifting Fixture
LEGEND:
A - Cap Screws (3 used)
B - JT07201A Transmission Lifting Fixture
C - Cap Screws (4 used)
D - JDG1760 Bushing (2 used)
Remove three transmission-to-mid-frame cap screws (A).
13/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
15. 81. Attach hoist to JT07201A Transmission Lifting Fixture (B).
82. Install fixture on transmission using cap screws (C) and two spacers from JDG1760 Spacer Kit (D) on front cap screws.
83.
CAUTION:
RXA0119760-UN: Transmission-to-Mid Frame Cap Screws
LEGEND:
A - Cap Screws (9 used)
Ensure that transmission is supported and does not drop off dowel pins or solenoid on left-hand side of transmission will be damaged.
Remove remaining transmission-to-mid-frame cap screws (A).
84. Move transmission forward and slide off drive shafts and mid-frame.
85. Lower transmission, rotate 90°, and remove from left-hand side.
AC20456,0000A59-19-20150414
14/14
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
16. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Install Transmission
Install Transmission
1.
RXA0079536-UN: Mid-Frame Pilot Pins
LEGEND:
A - DFRW231 Guide Pins (2 used)
B - O-rings
Install two DFRW231—Guide Pins (A) in mid-frame.
2. Replace O-rings (B) in drive shafts.
3. Install transmission and tighten transmission-to-mid-frame cap screws to specification [Zinc-Plate Coated] .
4.
Item Measurement Specification
Transmission-to-Mid-Frame Cap
Screws
Torque 430 N·m
(317 lb.-ft.)
1/4
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
17. RXA0108031-UN: Alignment Pins
LEGEND:
A - JDG768 Pilot Pins (2 used)
Install two JDG768 Pilot Pins (A) in transmission.
5. IMPORTANT:
Ensure that gasket between differential case and transmission is oriented correctly.
RXA0107117-UN: ILS O-rings
RXA0107118-UN: ILS Gasket and O-rings
LEGEND:
A - O-rings (2 used)
B - O-rings (2 used)
C - Gasket
For ILS™ Tractors: Install new O-rings (A and B) and new gasket (C).
6. Roll front of tractor to transmission.
7. Install transmission-to-engine cap screws [Zinc-Flake Coated] and tighten to specification.
Item Measurement Specification
Transmission-to-Engine Cap Screws Torque 500 N·m
(369 lb.-ft.)
2/4
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
18. 8. Remove JDG1935 Auxiliary Drive Support .
9. Tighten auxiliary drive support-to-transmission cap screws to specification.
10.
RXA0078566-UN: JDG861 Torque Wrench Adapter
Push engine-to-transmission drive shaft V-ring seal rearward against transmission oil seal.
11. NOTE:
Torque wrench setting will be 103 N·m (76 lb.-ft.) when used with JDG861 Torque Wrench
Adapter and kept straight with torque wrench.
Torque value must be calculated for all other torque wrench adapters. (See Use Torque Wrench
Adapter in Section 10, Group 10).
Use JDG861 Torque Wrench Adapter (A) to tighten engine-to-transmission drive shaft cap screws.
12. IMPORTANT:
If a failure occurred causing contamination of transmission and hydraulic system, cleanup procedures
must be performed. Clean and flush differential housing and clean oil reservoir.
Fill hydraulic system. (See Fill Hydraulic System in Section 70, Group 05.)
13. For tractors with Front PTO: Install front PTO. (See Install Front PTO in Section 56, Group 40.)
14. For tractors with Front Hitch: Install front hitch. (See Remove and Install Front 3-Point Hitch in Section 70, Group
35.)
15. Purge, evacuate, and charge air conditioning system. (See Purge Air Conditioning System , Evacuate Air Conditioning
System , and Charge Air Conditioning System in Section 90, Group 10.)
Item Measurement Specification
Auxiliary Drive Support-to-
Transmission Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Item Measurement Specification
Engine-to-Transmission Drive Shaft
Cap Screws
Torque 126 N·m
(92 lb.-ft.)
3/4
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
19. 16.
RXA0056006-UN: Drive Shaft
LEGEND:
A - Drive Shaft
For tractors with ILS™: Connect drive shaft (A) and tighten universal joint-to-differential yoke cap screws to
specification.
17. NOTE:
Tractor may require jacking to remove splitting stands.
Raise tractor and remove splitting stands.
18. NOTE:
Do not overtighten manual drain valve.
Close ILS™ manual drain valve and tighten nut.
Item Measurement Specification
Universal Joint Cap Screws-to-
Differential Yoke
Torque 150 N·m
(110 lb.-ft.)
LN71218,000054E-19-20120712
4/4
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
20. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Remove Scavenge Pump
Remove Scavenge Pump
RXA0125769-UN: Transmission Drain Plug
RXA0125770-UN: Mid-Frame Bottom Plate
LEGEND:
A - Plug
B - Front Shield
C - Radar Sensor Connector
D - Plate
1. Drain transmission by removing plug (A). (See Drain Hydraulic System in Section 70, Group 05.)
2. Remove front shield (B).
3. Disconnect radar sensor connector (C), if equipped.
4. Remove bottom plate (D) from mid-frame.
1/5
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
21. 5.
RXA0125771-UN: Lower Drive Shaft
RXA0125772-UN: Oil Line, and Fittings
LEGEND:
A - Lower Drive Shaft
B - Front Yoke
C - Rear Fitting
D - Front Fitting
E - Line
Remove shaft (A).
6. Mark position of lower drive shaft front yoke (B) in relationship to transmission case.
7. NOTE:
Some line or hose connections may be Snap-To-Connect fittings. (See Servicing and
Connecting Snap-To-Connect STC™ Fittings in Section 10, Group 10.)
Disconnect rear fitting (C).
8. Disconnect front fitting (D) and remove line (E).
2/5
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 9.
RXA0125660-UN: Scavenge Pump Oil Seal
LEGEND:
A - V-ring Seal
B - Oil Seal
Remove V-ring seal (A) and oil seal (B).
10.
RXA0125773-UN: Scavenge Pump Cover
RXA0125774-UN: Scavenge Pump
LEGEND:
3/5
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
24. A - Snap Ring
B - Cap Screws (5 Used)
C - Scavenge Pump Cover
Remove snap ring (A).
11. Remove cap screws (B) and scavenge pump cover (C).
12.
RXA0125775-UN: Shaft Seal Rings and Gears
LEGEND:
A - Seal Rings (2 Used)
B - Gears
Remove seal rings (A) from shaft.
13. NOTE:
Some pitting of gears and housing is normal.
Remove and inspect gears (B).
14. NOTE:
Driver disks are part of D01044AA Bushing, Bearing and Seal Driver Set .
RW35222-UN: Idler Gear
LEGEND:
A - Bearings (2 Used)
4/5
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
25. Inspect needle roller bearings (A) and remove, if necessary, using a 16 mm (5/8 in.) driver and 13 mm (1/2 in.)
pilot disks.
15. Install new bearings using a 22 mm (7/8 in.) driver and 13 mm (1/2 in.) pilot disks.
16. Install bearings flush with outer surface of pump gear.
17.
RXA0125776-UN: Shaft Bearing
LEGEND:
A - Snap Ring
B - Bearing
Remove snap ring (A) and bearing (B)
18. Inspect bearing (B), replace as necessary and install in reverse order.
OURX985,00001CE-19-20120410
5/5
2020/6/27file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...