The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...ufujjdjkskemme
- The document provides instructions for removing and installing a flywheel, flywheel housing, crankshaft pulley, and crankshaft rear seal on an excavator engine.
- To remove the flywheel, the bolts securing it must be removed, then a lifting device is used to pull it off. The flywheel housing is removed by lifting it off with bolts and contains an oil seal that may need replacing.
- The crankshaft rear seal is removed using a slide hammer and distorter tools, and installed using a installer tool and retaining compound. The crankshaft pulley is removed using a puller tool and a socket.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...ufujjdjkskemme
- The document provides instructions for removing and installing a flywheel, flywheel housing, crankshaft pulley, and crankshaft rear seal on an excavator engine.
- To remove the flywheel, the bolts securing it must be removed, then a lifting device is used to pull it off. The flywheel housing is removed by lifting it off with bolts and contains an oil seal that may need replacing.
- The crankshaft rear seal is removed using a slide hammer and distorter tools, and installed using a installer tool and retaining compound. The crankshaft pulley is removed using a puller tool and a socket.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar cat 320 c l 320cl excavator (prefix sbn) service repair manual (s...ujfjjkskkemmd
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator, including:
- Removing and installing the flywheel using various tools.
- Removing the crankshaft rear seal and wear sleeve.
- Installing a new crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
The document gives detailed step-by-step instructions and illustrations for performing maintenance on these components. Safety notices are included and required tools are listed.
Caterpillar cat 336 d l excavator (prefix mds) service repair manual (mds0000...fksjksmmde
The document provides instructions for disassembling and assembling a piston pump. Key steps include:
1. Removing various components like the head, O-rings, pistons, and bearings.
2. Using tools like retaining ring pliers and a driver group to remove springs and retaining rings.
3. Taking safety precautions as parts are under spring tension.
4. Cleaning all parts thoroughly before assembly.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 325 d excavator (prefix scr) service repair manual (scr00001 ...hfjsekekmmd
The document provides instructions for removing and installing a camshaft on a Caterpillar C7 engine. It describes:
1) Removing components like the vibration damper, pulley, rocker arms, pushrods and front cover before removing the camshaft.
2) Using timing pins and a puller to remove the camshaft.
3) Cleaning all parts to prevent contamination before installation.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor. The procedure involves removing components like the valve lifters and timing gear cover. Marks are made on gears to ensure proper timing is maintained. The camshaft is then removed and lubricated before being reinstalled along with checking timing marks to ensure correct installation.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 938 g ii wheel loader (prefix rtb) service repair manual (rtb...fjsjjekdkme
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes 18 steps to disassemble components such as the axle shaft, planetary carrier assembly, bearing cone, and ring gear. It also describes 11 steps for installing duo-cone seals and reassembling the axle housing, emphasizing cleanliness and proper alignment of components. Tools required are listed in a table.
Caterpillar cat 329 d2 and 329d2l excavator (prefix thw) service repair manua...udjfjjsekekkem
The document provides instructions for removing and installing a flywheel on a C7.1 engine used in 329D2 and 329D2L excavators. The flywheel removal procedure involves removing mounting bolts using guide studs for support, then inspecting the flywheel and ring gear. The flywheel installation procedure specifies cleaning and heating the ring gear, positioning the flywheel using guide studs and lifting devices, and tightening mounting bolts to the specified torque. A separate section provides instructions for removing the crankshaft rear seal, which involves using a Torx socket to remove mounting screws and discarding the sealed assembly.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a Caterpillar 3066 engine. The procedures include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Using lifting equipment to remove the flywheel housing, which weighs approximately 65 pounds.
3. Inspecting the oil seal and replacing if needed before installing a new one along with the crankshaft wear sleeve.
4. Cleaning surfaces and installing a new gasket before reattaching the flywheel housing with bolts and washers.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a 323D LN and 323D S excavator. The removal procedure involves using tools to remove bolts securing the flywheel adapter, inner ring, and flywheel to the crankshaft. The flywheel and ring gear can then be lifted out. To install, the ring gear is heated and pressed onto the flywheel if removed previously. Tools are then used to lower the flywheel into place and bolts are installed to secure it to the crankshaft.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and rings.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 312 b l excavator (prefix 2ns) service repair manual (2ns0000...fjsekksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the flywheel from the crankshaft, and using lifting tools to pull the flywheel out of the housing.
3) Reversing the process to install a new or repaired flywheel housing, making sure to tighten bolts to the specified torque and check flywheel runout.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1. Removing the flywheel, inner ring, and adapter to access the flywheel housing.
2. Using lifting straps and tools to remove the flywheel housing, which weighs 50 kg.
3. Cleaning and inspecting the housing, flywheel, and related components before reinstallation. Precautions are given to prevent contamination.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve using a special tool during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing.
3) Securing the housing with bolts and installing a new oil seal and crankshaft sleeve.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 325 d excavator (prefix scr) service repair manual (scr00001 ...hfjsekekmmd
The document provides instructions for removing and installing a camshaft on a Caterpillar C7 engine. It describes:
1) Removing components like the vibration damper, pulley, rocker arms, pushrods and front cover before removing the camshaft.
2) Using timing pins and a puller to remove the camshaft.
3) Cleaning all parts to prevent contamination before installation.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat d6 h track type tractor (prefix 8kb) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing the camshaft on a Caterpillar D6H track-type tractor. The procedure involves removing components like the valve lifters and timing gear cover. Marks are made on gears to ensure proper timing is maintained. The camshaft is then removed and lubricated before being reinstalled along with checking timing marks to ensure correct installation.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 938 g ii wheel loader (prefix rtb) service repair manual (rtb...fjsjjekdkme
This document provides instructions for disassembling and assembling the axle housing of a Caterpillar 938G II wheel loader. It describes 18 steps to disassemble components such as the axle shaft, planetary carrier assembly, bearing cone, and ring gear. It also describes 11 steps for installing duo-cone seals and reassembling the axle housing, emphasizing cleanliness and proper alignment of components. Tools required are listed in a table.
Caterpillar cat 329 d2 and 329d2l excavator (prefix thw) service repair manua...udjfjjsekekkem
The document provides instructions for removing and installing a flywheel on a C7.1 engine used in 329D2 and 329D2L excavators. The flywheel removal procedure involves removing mounting bolts using guide studs for support, then inspecting the flywheel and ring gear. The flywheel installation procedure specifies cleaning and heating the ring gear, positioning the flywheel using guide studs and lifting devices, and tightening mounting bolts to the specified torque. A separate section provides instructions for removing the crankshaft rear seal, which involves using a Torx socket to remove mounting screws and discarding the sealed assembly.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a Caterpillar 3066 engine. The procedures include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Using lifting equipment to remove the flywheel housing, which weighs approximately 65 pounds.
3. Inspecting the oil seal and replacing if needed before installing a new one along with the crankshaft wear sleeve.
4. Cleaning surfaces and installing a new gasket before reattaching the flywheel housing with bolts and washers.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a 323D LN and 323D S excavator. The removal procedure involves using tools to remove bolts securing the flywheel adapter, inner ring, and flywheel to the crankshaft. The flywheel and ring gear can then be lifted out. To install, the ring gear is heated and pressed onto the flywheel if removed previously. Tools are then used to lower the flywheel into place and bolts are installed to secure it to the crankshaft.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and rings.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 312 b l excavator (prefix 2ns) service repair manual (2ns0000...fjsekksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the flywheel from the crankshaft, and using lifting tools to pull the flywheel out of the housing.
3) Reversing the process to install a new or repaired flywheel housing, making sure to tighten bolts to the specified torque and check flywheel runout.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1. Removing the flywheel, inner ring, and adapter to access the flywheel housing.
2. Using lifting straps and tools to remove the flywheel housing, which weighs 50 kg.
3. Cleaning and inspecting the housing, flywheel, and related components before reinstallation. Precautions are given to prevent contamination.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve using a special tool during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing.
3) Securing the housing with bolts and installing a new oil seal and crankshaft sleeve.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...fusjekkdmdmd2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing twelve bolts and the adapter to separate the housing from the flywheel.
2) Installing a new housing by positioning the adapter and securing it with twelve bolts.
3) Checking the flywheel runout after installation to ensure proper alignment.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...f8usejkddmmd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the adapter from the flywheel housing and remove the adapter.
2) Removing bolts to separate the inner ring from the flywheel and removing the inner ring.
3) Using lifting tools to remove the flywheel from the housing, which weighs 50kg.
4) Reversing the removal steps to install the flywheel housing, including securing the flywheel to the crankshaft with bolts and checking flywheel runout.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...kmdddmm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing the flywheel, adapter, inner ring, and bolts securing the flywheel to the crankshaft.
2) Installing the flywheel using lifting tools, bolts, and checking runout with a gauge.
3) Removing the crankshaft rear seal and wear sleeve using drilling, hammer, and distorter tools.
4) Installing a new rear seal and wear sleeve using a installer, locator, bolts, washer and compound.
Similar to Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw00001 and up) (13)
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567208
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing screws M16 X 2 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00605492
1. Remove twelve bolts (1) and washers from the adapter (2) .
2. Remove the adapter (2) from the flywheel housing.
Illustration 2 g00605497
3. Remove four socket head bolts (3) from the inner ring (4) .
4. Remove the inner ring (4) from the flywheel.
2/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605501
5. Remove six bolts (5) that secure flywheel (6) to the crankshaft. Check all bolts for stripped
threads. Replace the bolts, if necessary.
Illustration 4 g00605504
6. Install Tool (A), a strap, and a suitable lifting device onto the flywheel (6).
7. Use Tool (B) in order to remove the flywheel and ring gear out of the housing. The weight
of the flywheel is 50 kg (110 lb).
8. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 5 g00613038
a. Place the flywheel and ring gear assembly on a suitable support.
Note: Check the flywheel ring gear for the following conditions:cracks, damaged
dowel holes, worn ring gear and damaged ring gear.
Note: Identify the orientation of the old ring gear on the flywheel for proper
positioning, when the new ring gear is installed.
3/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Always wear protective gloves when handling parts that have been
heated.
b. Heat ring gear (7) uniformly.
c. Remove the ring gear (7) by tapping the ring gear all the way around the flywheel
(6) .
d. Reposition the flywheel in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:56:07 UTC+0800 2020
4/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:57:06 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:59:05 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:00:04 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:01:03 UTC+0800 2020
4/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:02:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:03:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...