This document provides instructions for removing a transmission from several tractor models. It outlines over 80 steps to disconnect lines, brackets, wiring and other components to separate the transmission from the engine and mid-frame. Precise installation of a splitting stand and lifting fixture are described to safely support the tractor during disassembly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Why Is Your BMW X3 Hood Not Responding To Release Commands
John deere 8235 r tractors service repair technical manual (tm110319)
1. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Specifications
Specifications
Item Measurement Specification
Transmission-to-Mid-Frame Cap
Screws
Torque 430 N·m
(317 lb.-ft.)
Transmission-to-Engine Cap Screws Torque 500 N·m
(369 lb.-ft.)
Auxiliary Drive Support-to-
Transmission Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Engine-to-Transmission Drive Shaft
Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Universal Joint Cap Screws-to-
Differential Yoke
Torque 150 N·m
(110 lb.-ft.)
Scavenge Pump-to-Manifold Cap
Screws
Torque 125 N·m
(92 lb.-ft.)
Scavenge Pump Seal Depth 0.5 mm
(0.020 in.)
Auxiliary Drive Shaft Cap Screws Torque 80 N·m
(59 lb.-ft.)
LN71218,0000554-19-20120712
1/1
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
2. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors Repair (S. N. —090000) (Russia S. N.
052201—055000)
Remove Transmission
Remove Transmission
RXA0119494-UN: Shield and Tool Box
LEGEND:
A - Shield
B - Step
C - Tool Box
D - Battery Cover
1. Position hood forward. (See Optional Forward Hood Position in Section 80, Group 05.)
2. Discharge air conditioning system. (See Discharge Air Conditioning System in Section 90, Group 10.)
3. Drain coolant from engine block and radiator.
4. Remove shield (A) and step (B).
5. Remove tool box (C) and battery cover (D).
6.
RXA0119496-UN: Battery Ground Cable
LEGEND:
A - Battery Ground Cable
B - Batteries (2 used)
C - Single Point Ground
Disconnect battery ground cable (A) from batteries (B) and from single point ground (C).
7.
RXA0119500-UN: Left-Hand Hood Spreader
1/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
3. RXA0119501-UN: Right-Hand Hood Spreader
LEGEND:
A - Hood Spreaders (2 used)
Remove hood spreaders (A).
8.
RXA0119553-UN: Positive Battery Cable
LEGEND:
A - Clamps (4 used)
B - Positive Battery Cable
Remove clamps (A) and positive battery cable (B).
9. Remove front weights, if equipped.
10. For tractors with Front Hitch: Remove front hitch. (See Remove and Install Front 3-Point Hitch in Section 70, Group 35.)
11. For tractors with Front PTO: Remove front PTO. (See Remove Front PTO in Section 56, Group 40.)
12.
RXA0109012-UN: Transmission Drain Plug
LEGEND:
A - Plug
B - Front Plate
Drain transmission by removing plug (A). (See Drain Hydraulic System in Section 70, Group 05.)
13. Remove access plate (B).
14. If equipped, remove radar sensor. (See Replace Radar Sensor in Section 40, Group 30.)
15. NOTE:
2/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
4. RXA0107812-UN: Left-Hand Side
RXA0107814-UN: Right-Hand Side
LEGEND:
A - Lines (5 used)
B - Clamp
Some lines use Snap-To-Connect fittings. (See Servicing and Connecting Snap-To-Connect STC™ Fittings in Section 10, Group 10.)
Line and hose configurations vary depending on tractor options.
Disconnect lines (A).
16. Cap and plug lines and ports to prevent contamination.
17. Remove clamp (B).
18.
RXA0107813-UN: Bottom of Transmission
RXA0107811-UN: Bottom of Transmission
LEGEND:
A - Transmission Lines (6 used)
Disconnect transmission lines (A).
19. Cap and plug lines and ports to prevent contamination.
3/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
5. 20.
RXA0125922-UN: Snap Ring and Line Clamp
LEGEND:
A - Snap Ring
B - Clamp
For tractors equipped with MFWD, perform the following:
a. Loosen MFWD drive shaft shield and remove steering line clamp (B).
b.
CAUTION:
Tractor ignition must be in the "OFF" position when checking position of MFWD drive shaft snap ring (A).
Position tractor with MFWD drive shaft snap ring (A) in downward position.
c. Disengage MFWD shaft snap ring and slide shaft forward to disengage from MFWD clutch.
21.
RXA0056006-UN: Drive Shaft
LEGEND:
A - Drive Shaft Universal Joint
For tractors with ILS™: Disconnect one drive shaft universal joint (A) from differential yoke and support drive shaft on lower control arm.
22.
RXA0111687-UN: Shield and Exhaust
LEGEND:
A - Shield
B - Exhaust Pipe
Remove shield (A).
23. Remove exhaust pipe (B). (See Service Exhaust System in Section 30, Group 25.)
4/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
6. 24.
RXA0111469-UN: Cab Riser Panel
RXA0111467-UN: Air Conditioner Lines
LEGEND:
A - Cab Riser Panel
B - Cap Screws (2 used)
C - Line Clamp
D - Air Conditioning Line (High Pressure)
E - Air Conditioning Line (Low Pressure)
Remove cab riser panel (A) by removing cap screws (B) under floor mat.
25. Remove line clamp (C).
26. Disconnect and plug air conditioner lines (D and E).
27.
RXA0119554-UN: Alternator
LEGEND:
A - Auxiliary Drive Belt
B - Alternator Wires (3 used)
C - Mounting Cap Screws (2 used)
D - Alternator
Remove auxiliary drive belt (A).
28. Identify, label, and disconnect alternator wires (B).
29. Remove mounting cap screws (C) and alternator (D).
5/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
7. 30.
RXA0119555-UN: Fan Drive Control Valve
LEGEND:
A - Fan Drive Control Valve
B - Line
C - Lines (2 used)
D - Cap Screws (2 used)
Identify, label, and disconnect harness from fan drive control valve (A).
31. Remove line (B).
32. Disconnect lines (C).
33. Cap and plug lines and ports to prevent contamination.
34. Remove cap screws (D) and fan drive control valve.
35.
RXA0119556-UN: Steering Lines and Vent Hose
LEGEND:
A - Steering Lines (2 used)
B - Vent Hose
Disconnect steering lines (A).
36. Disconnect vent hose (B).
37.
RXA0119557-UN: Heater Hoses
LEGEND:
A - Heater Hoses (2 used)
Remove heater hoses (A).
6/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
8. 38.
RXA0119558-UN: Fuel Return and Fan Drive Supply
LEGEND:
A - Fuel Return Line
B - Fan Drive Supply Line
Disconnect fuel return hose (A).
39. Disconnect fan drive supply line (B).
40. Cap and plug lines to prevent contamination.
41.
RXA0119560-UN: Fuel Supply Line
LEGEND:
A - Cap Screws (2 used)
B - Fuel Supply Line
Remove cap screws (A).
42. Remove fuel supply line (B).
43.
RXA0119561-UN: Oil Cooler Lines
LEGEND:
A - Oil Cooler Lines (2 used)
B - Air Line
Disconnect oil cooler lines (A).
44. For tractors equipped with Air Trailer Brakes: Remove air line (B).
45.
7/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
9. RXA0119562-UN: Harness
LEGEND:
A - Connectors (3 used)
B - Cap Screw, Clamp, and Ground Wires
C - Cap Screw
Disconnect harness connectors (A).
46. Remove cap screw, clamp, and ground wires (B).
47. Remove filter housing bracket cap screw (C).
48.
RXA0119559-UN: Auxiliary Drive Bracket
LEGEND:
A - Cap Screw
B - Cap Screws (4 used)
Remove filter housing bracket cap screw (A).
49. Remove auxiliary drive bracket cap screws (B).
50.
RXA0077936-UN: Wiring Connector
LEGEND:
A - Shield
B - Wiring Connector (4 used)
C - Harness Clamps (2 used)
D - Harness
Remove shield (A).
51. Disconnect wiring connectors (B) and remove harness (D) from harness clamps (C).
52. IMPORTANT:
RXA0080844-UN: Left-Hand Transmission Connectors
8/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
10. RXA0080846-UN: Right-Hand Transmission Connectors
RXA0080849-UN: Lower Half Transmission Connectors
LEGEND:
A - Solenoids (13 used)
B - Sensors (5 used)
C - Harness
D - Clamps (6 used)
Note harness routing and retention. Identify and label connectors for reassembly.
Identify, label, and disconnect solenoid (A) and sensor (B) connectors from transmission.
53. Note harness routing and remove harness (C) from clamps (D).
54. Move harness from mid frame to avoid damage to harness.
55.
RXA0078566-UN: Drive Shaft
LEGEND:
A - JDG861 Torque Wrench Adapter
Disconnect drive shaft using JDG820 Flywheel Rotation Tool and JDG861 Torque Wrench Adapter (A).
56.
CAUTION:
Stand may collapse and cause injury or death if pins are not installed correctly on stand. Each tube on the stand must be pinned together with another tube. One
pin may pass through all three tubes, or each pin may pass through two tubes depending on the tire size.
IMPORTANT:
9/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
11. Use only stands specified for stability when splitting the tractor.
RXA0079554-UN: Splitting Stand
RXA0079555-UN: Splitting Stand for ILS™
LEGEND:
A - JT07122-6 Rear Adapter Plates
B - JT07122-1 Splitting Stand
C - JDG2061 Front Adapter
D - JT07321 Rear Support Wheels
E - JT07122-7-1 Cross Member
F - JT07122-7-2 Upright Supports
For ALL tractors, perform the following steps: Install JT07122-6 Rear Adapter Plates (A) on JT07122 Splitting Stand (B). DO NOT tighten cap screws.
57. Install JDG2061 Front Adapter (C) on JT07122 Splitting Stand. Tighten cap screws.
58. IMPORTANT:
Front adapter (C) must be installed tight against plate on top of splitting stand to fit correctly on tractor.
NOTE:
JT07122-7-1 Cross Member and JT07122-7-2 Upright Supports are part of JT07122-7 Upright Supports .
Install JT07122-7-1 Cross Member (E). DO NOT tighten cap screws.
59. Install JT07321 Rear Support Wheels (D). DO NOT tighten cap screws.
60. DO NOT install JT07122-7-2 Upright Supports (F) at this time.
61.
RXA0079556-UN: Rear Splitting Stand
10/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
12. RXA0077253-UN: Front Support
LEGEND:
A - Cap Screws
B - Front Support
C - Front Frame Member
D - Locating Block
Install rear splitting stand on front of mid-frame using cap screws (A). Tighten all cap screws.
62. Adjust splitting stand wheels to properly support tractor.
63. NOTE:
Depending on tractor configuration, front tires will need removed, JDG2061 Front Adapter installed, and front tires installed. (For further information on removing and
installing front tires, see Operator’s Manual.)
Install JDG2061 Front Adapter so front support (B) is tight under front frame member (C) and locating blocks (D) are between front frame member.
64. For tractors with ILS™: Bleed off suspension system. (See Relieve System Pressure—ILS™ in Section 58, Group 05.)
65. NOTE:
RXA0119743-UN: Right-Hand Side
11/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
13. RXA0119744-UN: Left-Hand Side
LEGEND:
A - JT07122-7-2 Upright Supports (2 used)
B - Cap Screws (4 used)
JT07122-7-2 Upright Supports are part of JT07122-7 Upright Supports .
Install JT07122-7-2 Upright Supports (A) on front splitting stand.
66. Attach upright supports to engine block with cap screws (B).
67. Tighten cross-member cap screws.
68.
RXA0119757-UN: JDG1935 Auxiliary Drive Support
LEGEND:
A - JDG1935 Auxiliary Drive Support
B - Upright Support
C - Cap Screws (2 used)
D - Bracket
E - Lifting Screw
F - Cap Screws (10 used MFWD and 2WD) (16 used ILS)
Install JDG1935 Auxiliary Drive Support (A) to left-hand upright support (B).
69. Attach support (A) to auxiliary drive with cap screws (C).
70. Position bracket (D) under air cleaner and attach to support (A).
71. NOTE:
Use a prybar to assist lifting of auxiliary drive housing off dowel pins
Turn lifting screw (E) to lift auxiliary drive and air cleaner off transmission dowel pins.
72. Lower rear wheel of splitting stand so rear of engine is correctly supported.
73. Remove front frame-to-transmission cap screws (F) from both sides.
74.
CAUTION:
Avoid possible personal injury. DO NOT remove transmission-to-mid-frame cap screws. Doing so will collapse the splitting stand. Remove ONLY the front frame-
to-transmission cap screws.
Carefully roll front of tractor forward approximately 250—300 mm (10—12 in.).
12/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
14. 75.
RXA0104303-UN: JT07201A Transmission Lifting Fixture and Adapter
LEGEND:
A - JT07201A Transmission Lifting Fixture
B - Cap Screw
C - JDG1883 Adapter
Drill hole in JT07201A Transmission Lifting Fixture (A). (See DFRW210—Hole Drilled in JT07201 in Section 99, Group 05.)
76. Insert JDG1883 Transmission Lifting Fixture Adapter (C) and attach with cap screw (B).
77.
RXA0104302-UN: Transmission Lifting Fixture
LEGEND:
A - Cap Screw
B - MFWD and ILS Line
C - 2WD Line
Loosen cap screw (A) on JT07201A Transmission Lifting Fixture .
78. Align center of cap screw with line (B) for MFWD and ILS™, or line (C) for tractors with 2WD.
79. Tighten cap screw (A).
80.
RXA0119758-UN: Three Cap Screws
RXA0119759-UN: JT07201 Transmission Lifting Fixture
LEGEND:
A - Cap Screws (3 used)
B - JT07201A Transmission Lifting Fixture
C - Cap Screws (4 used)
D - JDG1760 Bushing (2 used)
Remove three transmission-to-mid-frame cap screws (A).
13/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
15. 81. Attach hoist to JT07201A Transmission Lifting Fixture (B).
82. Install fixture on transmission using cap screws (C) and two spacers from JDG1760 Spacer Kit (D) on front cap screws.
83.
CAUTION:
RXA0119760-UN: Transmission-to-Mid Frame Cap Screws
LEGEND:
A - Cap Screws (9 used)
Ensure that transmission is supported and does not drop off dowel pins or solenoid on left-hand side of transmission will be damaged.
Remove remaining transmission-to-mid-frame cap screws (A).
84. Move transmission forward and slide off drive shafts and mid-frame.
85. Lower transmission, rotate 90°, and remove from left-hand side.
AC20456,0000A59-19-20150414
14/14
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa816...
16. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Install Transmission
Install Transmission
1.
RXA0079536-UN: Mid-Frame Pilot Pins
LEGEND:
A - DFRW231 Guide Pins (2 used)
B - O-rings
Install two DFRW231—Guide Pins (A) in mid-frame.
2. Replace O-rings (B) in drive shafts.
3. Install transmission and tighten transmission-to-mid-frame cap screws to specification [Zinc-Plate Coated] .
4.
Item Measurement Specification
Transmission-to-Mid-Frame Cap
Screws
Torque 430 N·m
(317 lb.-ft.)
1/4
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
17. RXA0108031-UN: Alignment Pins
LEGEND:
A - JDG768 Pilot Pins (2 used)
Install two JDG768 Pilot Pins (A) in transmission.
5. IMPORTANT:
Ensure that gasket between differential case and transmission is oriented correctly.
RXA0107117-UN: ILS O-rings
RXA0107118-UN: ILS Gasket and O-rings
LEGEND:
A - O-rings (2 used)
B - O-rings (2 used)
C - Gasket
For ILS™ Tractors: Install new O-rings (A and B) and new gasket (C).
6. Roll front of tractor to transmission.
7. Install transmission-to-engine cap screws [Zinc-Flake Coated] and tighten to specification.
Item Measurement Specification
Transmission-to-Engine Cap Screws Torque 500 N·m
(369 lb.-ft.)
2/4
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
18. 8. Remove JDG1935 Auxiliary Drive Support .
9. Tighten auxiliary drive support-to-transmission cap screws to specification.
10.
RXA0078566-UN: JDG861 Torque Wrench Adapter
Push engine-to-transmission drive shaft V-ring seal rearward against transmission oil seal.
11. NOTE:
Torque wrench setting will be 103 N·m (76 lb.-ft.) when used with JDG861 Torque Wrench
Adapter and kept straight with torque wrench.
Torque value must be calculated for all other torque wrench adapters. (See Use Torque Wrench
Adapter in Section 10, Group 10).
Use JDG861 Torque Wrench Adapter (A) to tighten engine-to-transmission drive shaft cap screws.
12. IMPORTANT:
If a failure occurred causing contamination of transmission and hydraulic system, cleanup procedures
must be performed. Clean and flush differential housing and clean oil reservoir.
Fill hydraulic system. (See Fill Hydraulic System in Section 70, Group 05.)
13. For tractors with Front PTO: Install front PTO. (See Install Front PTO in Section 56, Group 40.)
14. For tractors with Front Hitch: Install front hitch. (See Remove and Install Front 3-Point Hitch in Section 70, Group
35.)
15. Purge, evacuate, and charge air conditioning system. (See Purge Air Conditioning System , Evacuate Air Conditioning
System , and Charge Air Conditioning System in Section 90, Group 10.)
Item Measurement Specification
Auxiliary Drive Support-to-
Transmission Cap Screws
Torque 126 N·m
(92 lb.-ft.)
Item Measurement Specification
Engine-to-Transmission Drive Shaft
Cap Screws
Torque 126 N·m
(92 lb.-ft.)
3/4
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
19. 16.
RXA0056006-UN: Drive Shaft
LEGEND:
A - Drive Shaft
For tractors with ILS™: Connect drive shaft (A) and tighten universal joint-to-differential yoke cap screws to
specification.
17. NOTE:
Tractor may require jacking to remove splitting stands.
Raise tractor and remove splitting stands.
18. NOTE:
Do not overtighten manual drain valve.
Close ILS™ manual drain valve and tighten nut.
Item Measurement Specification
Universal Joint Cap Screws-to-
Differential Yoke
Torque 150 N·m
(110 lb.-ft.)
LN71218,000054E-19-20120712
4/4
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa81c...
20. TM110319 - 8235R, 8260R, 8285R, 8310R, 8335R, and 8360R Tractors
Repair (S. N. —090000) (Russia S. N. 052201—055000)
Remove Scavenge Pump
Remove Scavenge Pump
RXA0125769-UN: Transmission Drain Plug
RXA0125770-UN: Mid-Frame Bottom Plate
LEGEND:
A - Plug
B - Front Shield
C - Radar Sensor Connector
D - Plate
1. Drain transmission by removing plug (A). (See Drain Hydraulic System in Section 70, Group 05.)
2. Remove front shield (B).
3. Disconnect radar sensor connector (C), if equipped.
4. Remove bottom plate (D) from mid-frame.
1/5
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
21. 5.
RXA0125771-UN: Lower Drive Shaft
RXA0125772-UN: Oil Line, and Fittings
LEGEND:
A - Lower Drive Shaft
B - Front Yoke
C - Rear Fitting
D - Front Fitting
E - Line
Remove shaft (A).
6. Mark position of lower drive shaft front yoke (B) in relationship to transmission case.
7. NOTE:
Some line or hose connections may be Snap-To-Connect fittings. (See Servicing and
Connecting Snap-To-Connect STC™ Fittings in Section 10, Group 10.)
Disconnect rear fitting (C).
8. Disconnect front fitting (D) and remove line (E).
2/5
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 9.
RXA0125660-UN: Scavenge Pump Oil Seal
LEGEND:
A - V-ring Seal
B - Oil Seal
Remove V-ring seal (A) and oil seal (B).
10.
RXA0125773-UN: Scavenge Pump Cover
RXA0125774-UN: Scavenge Pump
LEGEND:
3/5
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
24. A - Snap Ring
B - Cap Screws (5 Used)
C - Scavenge Pump Cover
Remove snap ring (A).
11. Remove cap screws (B) and scavenge pump cover (C).
12.
RXA0125775-UN: Shaft Seal Rings and Gears
LEGEND:
A - Seal Rings (2 Used)
B - Gears
Remove seal rings (A) from shaft.
13. NOTE:
Some pitting of gears and housing is normal.
Remove and inspect gears (B).
14. NOTE:
Driver disks are part of D01044AA Bushing, Bearing and Seal Driver Set .
RW35222-UN: Idler Gear
LEGEND:
A - Bearings (2 Used)
4/5
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...
25. Inspect needle roller bearings (A) and remove, if necessary, using a 16 mm (5/8 in.) driver and 13 mm (1/2 in.)
pilot disks.
15. Install new bearings using a 22 mm (7/8 in.) driver and 13 mm (1/2 in.) pilot disks.
16. Install bearings flush with outer surface of pump gear.
17.
RXA0125776-UN: Shaft Bearing
LEGEND:
A - Snap Ring
B - Bearing
Remove snap ring (A) and bearing (B)
18. Inspect bearing (B), replace as necessary and install in reverse order.
OURX985,00001CE-19-20120410
5/5
2020/6/27
file:///C:/ProgramData/Service%20ADVISOR/Temp/TM110319_09001faa811...