SlideShare a Scribd company logo
1 of 25
Download to read offline
TM2264 - 35D and 50D Excavator
Fuel Injection Pump Remove and Install
Fuel Injection Pump Remove and Install
Fuel Injection Pump Remove
1. IMPORTANT:
Never steam clean or pour cold water on injection pump while the pump is running or warm. Doing so
can damage the pump.
Clean injection lines and area around the injection pump with cleaning solvent or a steam cleaner.
2. Remove radiator, fan, and belt.
 See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)
 See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.)
3. Remove intake manifold. See Intake Manifold Remove and Install . (Group 0400.)
4. Lower air conditioning compressor.
5.
RG13396A-UN: Remove Fuel Lines And Coolant Lines.
1/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
RG13397A-UN: Injection Pump Gear Cover
RG13398A-UN: Injection Pump Gear Timing Marks
LEGEND:
A - Fuel Inlet Line
B - Fuel Return Line
C - Injector Return Line
D - Coolant Line
E - Coolant Line
F - Fuel Shutoff Solenoid Wire Connector
G - Foam Spacer
H - Cap Screw (4 used)
I - Pump Gear Timing Mark
J - Idler Gear Timing Mark
Disconnect fuel inlet line (A), fuel return line (B), and injector return line (C).
6. Disconnect coolant lines (D and E).
7. Disconnect fuel shutoff solenoid wire connector (F).
8. Remove foam spacer (G).
9. Remove cap screws (H) and remove injection pump gear access cover.
10. NOTE:
For all the timing marks to become aligned, engine may need to be rotated up to fifty-two times.
2/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
Alignment marks (I and J) are both identified with a stamped letter “B”.
Rotate engine in the direction of rotation until mark (I) on pump gear aligns with mark on idler gear (J) (both identified
by a stamped letter B). Use chalk or paint to mark injection pump gear to idler gear.
11.
RG13399A-UN: Injection Pump Timing Gear
RG13400A-UN: Injection Pump Timing Gear Puller
3/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TX1062018A-UN: Injection Pump Timing Marks
LEGEND:
A - Timing Gear Nut and Washer
B - Cap Screw (4 used)
C - Threaded Puller Holes
D - Puller Cap Screw (2 used)
E - Gear Puller
F - Injection Pump Timing Mark
G - Gear Cover Mounting Plate Timing Mark
Remove gear retaining nut and washer (A).
12. IMPORTANT:
Do not loosen or disturb cap screws (B) securing gear to the hub. Gear to hub adjustment is pre-set to
comply with strict EPA emissions requirements and is not adjustable. This procedure is done at the
pump manufacturer and cannot be duplicated in the field.
Install puller (E) into threaded holes (C) on gear using cap screws (D).
13. IMPORTANT:
Engine must not be rotated when timing gear is removed from injection pump shaft. Engine should only
be rotated when timing gear is securely fastened to pump or engine damage could result.
Remove gear and hub assembly from injection pump shaft. Gear will stay inside timing cover.
14. IMPORTANT:
Marks must be made on the injection pump and the gear cover mounting plate to correctly install the
pump. If marks are not made, there will be no way to properly time the injection pump.
Note position of timing marks on gear cover mounting plate (G) and injection pump (F). Pump must be installed at the
exact same timing mark as when removed. Scribe a line as accurately and straight as possible at the pump flange
mark (F) onto the gear cover mounting plate.
4/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
15.
RG13402A-UN: Injection Pump Mounting Points
LEGEND:
A - External Lube Line
B - Cap Screw
C - Nut (3 used)
Remove external lube line (A) from pump.
16. Remove cap screw (B).
17. IMPORTANT:
Marks must be made on the injection pump and the gear cover mounting plate to properly install pump.
You must also record the injection pump timing number marked on the pump to correctly install the
pump. If marks are not made and the timing number not recorded, there will be no way to properly time
the injection pump.
Remove pump flange mounting nuts (C) and remove pump.
18. NOTE:
The injection pump timing number is stamped on the engine side of the fuel injection pump
housing. Treat this number as though there is a decimal point between the two digits. (Example 68
= 6.8).
Find and record pump timing number stamped on pump. This number will be needed if pump is being replaced or
recalibrated.
IMPORTANT:
DO NOT attempt to service the injection pump or governor. If unit is in need of repair, it must be serviced
by a qualified EPA/CARB certified fuel injection repair shop. If replacement is necessary, replace entire
unit. Do not rotate engine while injection pump is removed. If engine is rotated, the timing gear cover
must be removed to ensure correct timing.
Pump Installation
5/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
1.
RG13399A-UN: Injection Pump Timing Gear
LEGEND:
A - Timing Gear Nut and Washer
B - Cap Screw (4 used)
C - Threaded Puller Holes
Install new O-ring on injection pump.
2. Put injection pump onto back of gear cover mounting plate. Install three mounting nuts. Do not tighten. Align key on
shaft with keyway in gear hub. Ensure gear is still aligned to idler gear.
3. Install nut and washer (A) on pump shaft. Tighten nut to specification.
4.
TX1062057A-UN: Injection Pump Timing Marks
Item Measurement Specification
Fuel Injection Pump Drive Gear
Hub-to-Shaft Retaining Nut
Torque 78—88 N˙m
58—65 lb-ft
6/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
RG13415A-UN: Injection Pump Mounting
LEGEND:
A - Injection Pump Timing Mark
B - Gear Cover Mounting Plate Timing Mark
C - Pump Mounting Nut (3 used)
D - Cap Screw
E - External Lube Line
Align timing mark on injection pump (A) with correct mark on gear cover mounting plate (B).
5. Tighten three pump mounting nuts (C) to specification.
6. Install cap screw (D). Tighten to specification.
7. Fill pump with engine oil through external lube line port until oil runs out. Install external lube line. Tighten lube line
fitting (E) to specification.
8. Install cover for injection pump timing gear.
Item Measurement Specification
Injection Pump Mounting Nuts Torque 26 N˙m
228 lb-in.
Item Measurement Specification
Injection Pump Mounting Cap
Screw
Torque 26 N˙m
228 lb-in.
Item Measurement Specification
Injection Pump External Lube Line
Fitting
Torque 15 N˙m
133 lb-in.
7/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
9.
RG13396A-UN: Install Fuel and Coolant Lines
LEGEND:
A - Fuel Inlet Line
B - Fuel Return Line
C - Injectors Return Line
D - Coolant Line
E - Coolant Line
F - Fuel Shutoff Solenoid Wire Connector
G - Foam Spacer
Install spacer (G) between pump and engine block.
10. Connect fuel shutoff solenoid wire connector (F).
11. Connect fuel lines (A, B, and C).
12. Connect coolant lines (D and E).
13. Install intake manifold. See Intake Manifold Remove and Install . (Group 0400.)
14. Install radiator, fan, and belt.
 See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)
 See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.)
New, Rebuilt, or Recalibrated Pump Timing
8/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
1.
RG13614-UN: Injection Pump Sticker
LEGEND:
A - Middle 0° Line
B - 1° Line
C - 2° Line
D - 0.5° Line
Install timing mark sticker supplied with pump so that the (A) line is exactly in-line with the mark that was made on the
gear cover mounting plate when the pump was removed.
2. IMPORTANT:
Injection pump timing can not be performed without injection pump timing numbers from original and
replacement pumps. There is no way to properly install the injection pump without these numbers.
Calculate the difference between the timing numbers, recorded earlier, from the original and replacement/recalibrated
pumps. This calculated number will be needed to correctly time the pump.
Example: If the timing number on the replacement/recalibrated pump was 6.0, and the timing number on the original
pump is 4.0 (fuel injection angle of replacement/recalibrated pump) - (fuel injection angle of original pump), the
replacement pump should be timed at the +2.0° (advanced) mark (C) on the new timing mark sticker.
3. NOTE:
Rotating the injection pump away from the cylinder block will advance the timing and rotating the
injection pump toward the cylinder block will delay the timing.
Set the pump to the correct timing mark using the calculated number difference between the original and replacement
pumps. Adjust timing accordingly using the new timing mark sticker.
4. Hold the pump at the correct timing mark and tighten three pump mounting nuts and cap screw to specification.
9/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
5. If removed, install timing cover. See Timing Gear Cover Remove and Install . (Group 0400.)
6.
RG13396A-UN: Install Fuel And Coolant Lines
LEGEND:
A - Fuel Inlet Line
B - Fuel Return Line
C - Injectors Return Line
D - Coolant Line
E - Coolant Line
F - Fuel Shutoff Solenoid Wire Connector
G - Foam Spacer
Install spacer (G) between pump and engine block.
7. Connect fuel shutoff solenoid wire connector (F).
8. Connect fuel lines (A, B, and C).
9. Connect coolant lines (D and E).
10. Install intake manifold. See Intake Manifold Remove and Install . (Group 0400.)
11. Install radiator, fan, and belt.
 See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)
 See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)
 See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.)
Item Measurement Specification
Injection Pump Mounting Nuts Torque 26 N˙m
228 lb-in.
Injection Pump Mounting Cap
Screw
Torque 26 N˙m
228 lb-in.
OUO1030,00000CA-19-20090721
10/10
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TM2264 - 35D and 50D Excavator
Fuel Injection Nozzles Remove and Install
Fuel Injection Nozzles Remove and Install
General Nozzle Service Precautions
Before removal, thoroughly remove all dirt from the cylinder head around fuel injection nozzles. Clean with compressed air to
prevent dirt from entering the cylinders. Plug the bore in the cylinder head after each nozzle has been removed. Cap fuel line
openings as soon as they are disconnected.
Immediately fit protective caps over the nozzle tips and the line connections to avoid handling damage and getting debris in
fuel system.
Do not bend the fuel delivery lines, as this may affect their durability. When loosening the fuel pressure lines, hold male union
of nozzle line stationary with a backup wrench.
1. IMPORTANT:
Never steam clean or pour cold water on injection pump while the pump is running or warm. Doing so
can damage the pump.
Clean the injection pump lines and area around the nozzles using a parts cleaning solvent or steam cleaner.
NOTE:
Nozzles are matched to the cylinders. If removing more than one nozzle, tag each nozzle,
according to the cylinder from which it was removed.
1/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
2.
RG13407-UN: Fuel Injector Components
LEGEND:
A - Cap Screw and Washer
B - Retaining Plate
C - Hose Clamp
D - Leak-Off Hose
E - Injection Nozzle
F - Ring
G - Heat Protector
Loosen fuel injection line connectors-to-nozzles slightly to release pressure in the fuel system.
3. Loosen line clamp(s) and remove fuel injection lines.
4. Remove clamps (C) and leak-off hoses (D).
5. Remove cap screw and washer (A) and retaining plate (B).
6. Remove injection nozzle (E), ring (F), and TEFLON ® heat protector (G). If ring and protector stay in cylinder head,
thread a cap screw into protector and pull from cylinder head.
2/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
7.
M82126A-UN: If Nozzles Stick in Cylinder Head
LEGEND:
A - Large Flat Washer
B - Nut (2 used)
C - Cap Screw
D - Old Injection Line Nut
E - Injection Nozzle
If nozzles are stuck in cylinder head:
Grind the head of a cap screw (C) so it fits inside a nut from an old injection line (D).
Use two nuts (B) to attach a large flat washer (A) to the cap screw.
Install assembly onto nozzle and use a puller and slide hammer to pull nozzle from cylinder head.
8. Test injection nozzles. Perform Fuel Injection Nozzle Check . (Group 9010-25.)
9. Installation is done in the reverse order of removal.
10. Tighten retaining plate nuts.
Item Measurement Specification
Fuel Injection Retaining Plate Cap
Screw
Torque 24—28 N˙m
212—248 lb-in
TEFLON is a trademark of Du Pont Co. OUO1030,00000CB-19-20051128
3/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TM2264 - 35D and 50D Excavator
Fuel Injection Nozzles Disassemble and Assemble
Fuel Injection Nozzles Disassemble and Assemble
Fuel Injection Nozzles Disassemble
RG11097A-UN: Hole-Type Nozzle
LEGEND:
A - Injector Body
B - Shims
C - Spring
D - Spring Seat
E - Separator Plate
F - Nozzle Valve
G - Nozzle Body
H - Retaining Nut
I - Index Pin (2 used)
NOTE:
If servicing more than one nozzle, keep parts for each nozzle separate from one another.
1. Disassemble fuel injection nozzles.
1/5
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
2. IMPORTANT:
If injection nozzles are disassembled to be cleaned, the same number and thickness of shims must be
installed.
Clean and inspect nozzle components.
Fuel Injection Nozzles Clean and Inspect
2/5
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
M37684A-UN: Injection Nozzles
3/5
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
M82326B-UN: Nozzle Body, Separator Plate, Contact & Sealing Surfaces
LEGEND:
A - Injector Body
B - Fuel Return Pipe
C - Shims
D - Spring
E - Index Pin
F - Separator Plate
G - Nozzle Body
H - Nozzle Valve
I - Retaining Nut
J - Spring Seat
K - Nozzle Contact Surfaces
L - Sealing Surfaces
NOTE:
To clean nozzles properly, JDF13B Nozzle Cleaning Kit is recommended. The cleaning kit is available
through the John Deere SERVICEGARD ™ Catalog.
1. Remove anti-corrosive grease from new or reconditioned nozzles by washing them thoroughly in diesel fuel.
2. IMPORTANT:
Never use a steel brush to clean nozzles as this will distort the spray hole.
Remove carbon from used nozzles, and clean by washing in diesel fuel. If parts are coated with hardened carbon or
lacquer, it may be necessary to use a brass wire brush (supplied in nozzle cleaning kit).
3. After removing carbon or lacquer from the exterior of nozzle, inspect sealing surfaces between separator plate and
nozzle body for nicks or scratches.
4. Inspect condition of separator plate and nozzle body. Contact area of separator plate (both parts) must not be scored
or pitted. Use an inspection magnifier to aid in making the inspection.
5. Check nozzle contact surface on separator plate for wear. If contact surface is more than specification, replace nozzle
assembly.
6. Inspect the piston (large) part of nozzle valve to see that it is not scratched or scored and that lower (tip) end of valve
is not broken. If any of these conditions are present, replace the nozzle assembly.
Item Measurement Specification
Fuel Injection Nozzle Contact
Surface
Size 0.10 mm
0.0039 in.
4/5
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
7.
M35919-UN: Nozzle Valve & Body
LEGEND:
A - Nozzle Valve
B - Nozzle Body
Further inspect the nozzle assembly by performing a slide test. Use the following procedure:
a. Dip the nozzle valve in clean diesel fuel. Insert valve (A) in nozzle body (B).
b. Hold nozzle vertical, and pull valve out about 1/3 of its engaged length as shown.
c. Release valve. Valve should slide down to its seat by its own weight.
Replace nozzle assembly if the valve does not slide freely to its seat.
Fuel Injection Nozzles Assemble
1. Assembly is done in the reverse order of disassembly.
2. Tighten retaining nut (H) to specification.
3. After assembly is complete, test injection nozzle. Perform Fuel Injection Nozzle Check . (Group 9010-25.)
Item Measurement Specification
Fuel Injection Nozzle Retaining Nut Torque 43 N˙m
31 lb-ft
SERVICEGARD is a trademark of Deere & Company. OUO1030,00000CC-19-20051128
5/5
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TM2264 - 35D and 50D Excavator
Rocker Arm Cover Remove and Install
Rocker Arm Cover Remove and Install
RG13393-UN: Rocker Arm Cover
LEGEND:
A - Special Nut (3 used)
B - Diaphragm Cover
C - Spring
D - Diaphragm
E - Oil Filler Cap
F - Gasket
G - Baffle
H - Baffle Plate
I - Gasket
J - Rocker Arm Cover
K - Crankcase Breather Tube
L - O-Ring
1/2
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
M - Spring Plate
1. Remove the special nuts (A).
2. Disconnect crankcase breather tube (K).
3. Remove rocker arm cover (J) from cylinder head.
4. Remove diaphragm cover (B).
5. Remove and inspect spring (C) and diaphragm (D). Replace if damaged or deteriorated.
6. Remove baffle plate (H) and baffle (G).
7. Wash baffle in solvent and blow dry with compressed air. Replace baffle if it is damaged or deteriorated.
8. Install baffle and baffle plate.
9. Install diaphragm, spring plate (M), spring, and diaphragm cover.
10. Inspect gasket (I) and O-rings (L) before reinstalling rocker arm cover. Replace if damaged.
11. Clean cylinder head surface and install rocker arm cover on cylinder head. Install special nuts and tighten to
specification.
Item Measurement Specification
Rocker Arm Cover Special Nuts Torque 18 N˙m
156 lb-in.
OUO1030,000006C-19-20051128
2/2
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TM2264 - 35D and 50D Excavator
Rocker Arm Shaft Assembly Repair
Rocker Arm Shaft Assembly Repair
Rocker Arm Shaft Disassemble
1.
RG13416-UN: Rocker Arm Shaft Assembly
LEGEND:
A - Nut
B - Adjusting Screw
C - Mounting Cap Screw
D - Nut
E - Stud
F - Rocker Arm End Support
G - Rocker Arm Shaft
H - Push Rod
I - Valve Cap
J - Intake Valve Rocker Arm
K - Exhaust Valve Rocker Arm
L - Mounting Cap Screw
M - Rocker Arm Shaft Spring
N - Rocker Arm Center Support
Remove rocker arm cover. See Rocker Arm Cover Remove and Install . (Group 0400.)
2. Remove rocker arm end support mounting cap screws (C).
3. Remove rocker arm center support mounting cap screws (L).
4. Lift rocker arm assembly from cylinder head and set on bench.
5. NOTE:
When disassembling the rocker arm assembly, replace components in same location on rocker arm shaft they were removed from.
Slide rocker arm assembly components off rocker arm shaft while noting positions for reassembly.
6. Lift push rods (H) from cylinder head and note order of removal for reassembly in same positions in head.
Rocker Arm Shaft Inspect
1.
M35262A-UN: Measure Rocker Arm Shaft Outer Diameter
1/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
M82022A-UN: Measuring Rocker Arm ID
LEGEND:
A - Rocker Arm Shaft
B - Rocker Arm
Measure outer diameter of rocker arm shaft (A) at each rocker arm location.
Replace rocker arm shaft if less than wear limit.
2. Measure inner diameters of rocker arms (B) and supports.
Replace rocker arms or supports if ID is more than wear limit.
3.
M82023A-UN: Measure Length and Bending of Push Rod
LEGEND:
A - Push Rod Length
B - Push Rod Bend
Measure length (A) and bending (B) of push rod.
Replace push rod if not within specifications.
Item Measurement Specification
Rocker Arm Shaft OD 15.97—15.98 mm
0.6286—0.6293 in.
Wear Limit 15.95 mm
0.6280 in.
Item Measurement Specification
Rocker Arm Shaft Support ID 16.00—16.02 mm
0.630—0.631 in.
Wear Limit 16.09 mm
0.633 in.
Rocker Arm Shaft-to-Rocker Arm
and Shaft Support Clearance
Wear Limit 0.14 mm
0.006 in.
Item Measurement Specification
Push Rod Length 178.2—178.75 mm
7.018—7.037 in.
Push Rod Bend Wear Limit 0.03 mm
0.001 in.
2/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
Rocker Arm Shaft Assemble
1. NOTE:
Lubricate all parts with clean oil during assembly.
Install push rods in cylinder head with ball-shaped end down in head. Push rods should be in same locations they were removed from.
2. Assemble rocker arm assembly components in the reverse order of removal.
3. Place rocker arm assembly on cylinder head. Align rocker arms with valves and push rods. Align rocker arm end supports and center supports with corresponding holes in head.
4. Install rocker arm support mounting cap screws and torque to specification.
5. Adjust valve clearance. See Engine Valve Lash (Clearance) Check and Adjustment . (Group 9010-25.)
Item Measurement Specification
Rocker Arm Support Cap Screws Torque 26 N˙m
230 lb-in.
OUO1030,000006F-19-20060105
3/3
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
TM2264 - 35D and 50D Excavator
Cylinder Head Remove and Install
Cylinder Head Remove and Install
Cylinder Head Remove
T207557-UN: Cylinder Head Remove and Install
1/8
2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...

More Related Content

What's hot

Personal Survival and Social Responsibilities(PSSR)
Personal Survival and Social Responsibilities(PSSR)Personal Survival and Social Responsibilities(PSSR)
Personal Survival and Social Responsibilities(PSSR)nmahi96
 
complete guide to process valves
complete guide to process valves complete guide to process valves
complete guide to process valves Elsayed Amer
 
Personal Survival Techniques(PST)
Personal Survival Techniques(PST)Personal Survival Techniques(PST)
Personal Survival Techniques(PST)nmahi96
 
Manual de mecânica de motos sar
Manual de mecânica de motos   sarManual de mecânica de motos   sar
Manual de mecânica de motos sarwilliammagalhaes
 
Reciprocating Piston Engine Lubrication System
Reciprocating Piston Engine Lubrication SystemReciprocating Piston Engine Lubrication System
Reciprocating Piston Engine Lubrication Systemlccmechanics
 
Rudders and propellers
Rudders and propellersRudders and propellers
Rudders and propellersRishi Vrmn
 
Sewage treatment plant on a ship
Sewage treatment plant on a ship Sewage treatment plant on a ship
Sewage treatment plant on a ship Nejat Öztezcan
 
Chapter 2 surface equipment (1)
Chapter 2 surface equipment (1)Chapter 2 surface equipment (1)
Chapter 2 surface equipment (1)Dr. Arzu Javadova
 
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-componentsJohansson Engineering Ltd
 
ISPS: Security Awareness Training / Designated Security Duty
ISPS: Security Awareness Training / Designated Security DutyISPS: Security Awareness Training / Designated Security Duty
ISPS: Security Awareness Training / Designated Security DutyCapt Moin Uddin
 
+Paritta sutta 11palimyanmarbooknew-8.
+Paritta sutta 11palimyanmarbooknew-8.+Paritta sutta 11palimyanmarbooknew-8.
+Paritta sutta 11palimyanmarbooknew-8.Thukha Thu
 
sea trial.docx
sea trial.docxsea trial.docx
sea trial.docxmaneesh10
 
Fresh water generator onboard
Fresh water generator onboardFresh water generator onboard
Fresh water generator onboardJIBRIN HABIBU
 

What's hot (20)

Personal Survival and Social Responsibilities(PSSR)
Personal Survival and Social Responsibilities(PSSR)Personal Survival and Social Responsibilities(PSSR)
Personal Survival and Social Responsibilities(PSSR)
 
Ship common systems
Ship common systemsShip common systems
Ship common systems
 
complete guide to process valves
complete guide to process valves complete guide to process valves
complete guide to process valves
 
Nmlc ef1 module 1
Nmlc ef1 module 1Nmlc ef1 module 1
Nmlc ef1 module 1
 
Personal Survival Techniques(PST)
Personal Survival Techniques(PST)Personal Survival Techniques(PST)
Personal Survival Techniques(PST)
 
well control (1)
 well control (1) well control (1)
well control (1)
 
Manual de mecânica de motos sar
Manual de mecânica de motos   sarManual de mecânica de motos   sar
Manual de mecânica de motos sar
 
Ssd spm
Ssd   spmSsd   spm
Ssd spm
 
Reciprocating Piston Engine Lubrication System
Reciprocating Piston Engine Lubrication SystemReciprocating Piston Engine Lubrication System
Reciprocating Piston Engine Lubrication System
 
2.1 rig types
2.1 rig types2.1 rig types
2.1 rig types
 
Rudders and propellers
Rudders and propellersRudders and propellers
Rudders and propellers
 
Sewage treatment plant on a ship
Sewage treatment plant on a ship Sewage treatment plant on a ship
Sewage treatment plant on a ship
 
CARGO OIL PUMPING SYSTEM.pdf
CARGO OIL PUMPING SYSTEM.pdfCARGO OIL PUMPING SYSTEM.pdf
CARGO OIL PUMPING SYSTEM.pdf
 
Chapter 2 surface equipment (1)
Chapter 2 surface equipment (1)Chapter 2 surface equipment (1)
Chapter 2 surface equipment (1)
 
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components
16176745 drilling-rig-operations-a-to-z-rotary-drilling-rig-components
 
ISPS: Security Awareness Training / Designated Security Duty
ISPS: Security Awareness Training / Designated Security DutyISPS: Security Awareness Training / Designated Security Duty
ISPS: Security Awareness Training / Designated Security Duty
 
Wellheads Training .pdf
Wellheads Training .pdfWellheads Training .pdf
Wellheads Training .pdf
 
+Paritta sutta 11palimyanmarbooknew-8.
+Paritta sutta 11palimyanmarbooknew-8.+Paritta sutta 11palimyanmarbooknew-8.
+Paritta sutta 11palimyanmarbooknew-8.
 
sea trial.docx
sea trial.docxsea trial.docx
sea trial.docx
 
Fresh water generator onboard
Fresh water generator onboardFresh water generator onboard
Fresh water generator onboard
 

Similar to John deere 50 d compact excavator service repair technical manual (tm2264)

John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdflanji4905796341
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdflanji4905796341
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfdongba082928
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfdongba082928
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfci1289tong
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfci1289tong
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfafbn276187
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfafbn276187
 
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...zhui3de
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...fuekdksmemm
 
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...ufjskekfmsme
 
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...fjeisldkmemm
 
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...fksuekdjsekmmd
 
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...fuujsjejkekmd
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...fujskekfksmem
 
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...fujskeksmemqa
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...fujjdfjkksekmem
 

Similar to John deere 50 d compact excavator service repair technical manual (tm2264) (17)

John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 50D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdfJohn Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
John Deere 35D Compact Excavator Service Repair Technical Manual (TM2264).pdf
 
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...
John Deere 17D Compact Excavator Service Repair Manual Instant Download (TM10...
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z425 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z465 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z435 e ztrak residential mower (sn.100001 and up) service repair t...
 
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
John deere z445 e ztrak residential mower (sn.100001 and up) service repair t...
 

More from ufjjsjefkksemm

Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...ufjjsjefkksemm
 
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...ufjjsjefkksemm
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 100 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 100 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 100 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 100 tractor service repair manualufjjsjefkksemm
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 90 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 90 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 90 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 90 tractor service repair manualufjjsjefkksemm
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 80 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 80 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 80 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 80 tractor service repair manualufjjsjefkksemm
 
Mc cormick bmax (2007 ) - rt62 - 100 tractor service repair manual
Mc cormick bmax (2007  ) - rt62 - 100 tractor service repair manualMc cormick bmax (2007  ) - rt62 - 100 tractor service repair manual
Mc cormick bmax (2007 ) - rt62 - 100 tractor service repair manualufjjsjefkksemm
 
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manual
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manualMc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manual
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manualufjjsjefkksemm
 
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...ufjjsjefkksemm
 
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...ufjjsjefkksemm
 
Mc cormick (2011 ) - rs43 - 6450 ism-vrm tractor service repair manual
Mc cormick (2011  ) - rs43 - 6450 ism-vrm tractor service repair manualMc cormick (2011  ) - rs43 - 6450 ism-vrm tractor service repair manual
Mc cormick (2011 ) - rs43 - 6450 ism-vrm tractor service repair manualufjjsjefkksemm
 
Komatsu wa250 6 wheel loader service repair manual sn75001 and up
Komatsu wa250 6 wheel loader service repair manual sn75001 and upKomatsu wa250 6 wheel loader service repair manual sn75001 and up
Komatsu wa250 6 wheel loader service repair manual sn75001 and upufjjsjefkksemm
 
Komatsu d31 pl 20 dozer bulldozer service repair manual
Komatsu d31 pl 20 dozer bulldozer service repair manualKomatsu d31 pl 20 dozer bulldozer service repair manual
Komatsu d31 pl 20 dozer bulldozer service repair manualufjjsjefkksemm
 
Komatsu d31 p 20a dozer bulldozer service repair manual
Komatsu d31 p 20a dozer bulldozer service repair manualKomatsu d31 p 20a dozer bulldozer service repair manual
Komatsu d31 p 20a dozer bulldozer service repair manualufjjsjefkksemm
 
Komatsu d31 p 20 dozer bulldozer service repair manual
Komatsu d31 p 20 dozer bulldozer service repair manualKomatsu d31 p 20 dozer bulldozer service repair manual
Komatsu d31 p 20 dozer bulldozer service repair manualufjjsjefkksemm
 
Komatsu d31 e 20 dozer bulldozer service repair manual
Komatsu d31 e 20 dozer bulldozer service repair manualKomatsu d31 e 20 dozer bulldozer service repair manual
Komatsu d31 e 20 dozer bulldozer service repair manualufjjsjefkksemm
 
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)ufjjsjefkksemm
 
Komatsu 12 v170 1 diesel engine service repair manual
Komatsu 12 v170 1 diesel engine service repair manualKomatsu 12 v170 1 diesel engine service repair manual
Komatsu 12 v170 1 diesel engine service repair manualufjjsjefkksemm
 
John deere 500 trail buck utility atv service repair manual (tm2160)
John deere 500 trail buck utility atv service repair manual (tm2160)John deere 500 trail buck utility atv service repair manual (tm2160)
John deere 500 trail buck utility atv service repair manual (tm2160)ufjjsjefkksemm
 
John deere 500 buck utility atv service repair manual (tm2153)
John deere 500 buck utility atv service repair manual (tm2153)John deere 500 buck utility atv service repair manual (tm2153)
John deere 500 buck utility atv service repair manual (tm2153)ufjjsjefkksemm
 
John deere 315 d side shift loader service repair technical manual (tm1497)
John deere 315 d side shift loader service repair technical manual (tm1497)John deere 315 d side shift loader service repair technical manual (tm1497)
John deere 315 d side shift loader service repair technical manual (tm1497)ufjjsjefkksemm
 

More from ufjjsjefkksemm (20)

Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 75 tractor service repair m...
 
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...
Mc cormick c l europa tier 2 (2007-2008) - rs50 - 70 tractor service repair m...
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 100 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 100 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 100 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 100 tractor service repair manual
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 90 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 90 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 90 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 90 tractor service repair manual
 
Mc cormick bmax tier 3 (2011 ) - rt64 - 80 tractor service repair manual
Mc cormick bmax tier 3 (2011  ) - rt64 - 80 tractor service repair manualMc cormick bmax tier 3 (2011  ) - rt64 - 80 tractor service repair manual
Mc cormick bmax tier 3 (2011 ) - rt64 - 80 tractor service repair manual
 
Mc cormick bmax (2007 ) - rt62 - 100 tractor service repair manual
Mc cormick bmax (2007  ) - rt62 - 100 tractor service repair manualMc cormick bmax (2007  ) - rt62 - 100 tractor service repair manual
Mc cormick bmax (2007 ) - rt62 - 100 tractor service repair manual
 
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manual
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manualMc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manual
Mc cormick 6600 arm (2011 2013) - rs42 - 6660 arm tractor service repair manual
 
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...
Mc cormick 9 7 series (2014- ) - rs37 - 9095 - 90105 ism tractor service repa...
 
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...
Mc cormick 9 7 series (2014- ) - rs37 - 7070 - 7080 arm tractor service repai...
 
Mc cormick (2011 ) - rs43 - 6450 ism-vrm tractor service repair manual
Mc cormick (2011  ) - rs43 - 6450 ism-vrm tractor service repair manualMc cormick (2011  ) - rs43 - 6450 ism-vrm tractor service repair manual
Mc cormick (2011 ) - rs43 - 6450 ism-vrm tractor service repair manual
 
Komatsu wa250 6 wheel loader service repair manual sn75001 and up
Komatsu wa250 6 wheel loader service repair manual sn75001 and upKomatsu wa250 6 wheel loader service repair manual sn75001 and up
Komatsu wa250 6 wheel loader service repair manual sn75001 and up
 
Komatsu d31 pl 20 dozer bulldozer service repair manual
Komatsu d31 pl 20 dozer bulldozer service repair manualKomatsu d31 pl 20 dozer bulldozer service repair manual
Komatsu d31 pl 20 dozer bulldozer service repair manual
 
Komatsu d31 p 20a dozer bulldozer service repair manual
Komatsu d31 p 20a dozer bulldozer service repair manualKomatsu d31 p 20a dozer bulldozer service repair manual
Komatsu d31 p 20a dozer bulldozer service repair manual
 
Komatsu d31 p 20 dozer bulldozer service repair manual
Komatsu d31 p 20 dozer bulldozer service repair manualKomatsu d31 p 20 dozer bulldozer service repair manual
Komatsu d31 p 20 dozer bulldozer service repair manual
 
Komatsu d31 e 20 dozer bulldozer service repair manual
Komatsu d31 e 20 dozer bulldozer service repair manualKomatsu d31 e 20 dozer bulldozer service repair manual
Komatsu d31 e 20 dozer bulldozer service repair manual
 
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)
Komatsu d21 a,p 8 dozer bulldozer service repair manual (sn 83001 and up)
 
Komatsu 12 v170 1 diesel engine service repair manual
Komatsu 12 v170 1 diesel engine service repair manualKomatsu 12 v170 1 diesel engine service repair manual
Komatsu 12 v170 1 diesel engine service repair manual
 
John deere 500 trail buck utility atv service repair manual (tm2160)
John deere 500 trail buck utility atv service repair manual (tm2160)John deere 500 trail buck utility atv service repair manual (tm2160)
John deere 500 trail buck utility atv service repair manual (tm2160)
 
John deere 500 buck utility atv service repair manual (tm2153)
John deere 500 buck utility atv service repair manual (tm2153)John deere 500 buck utility atv service repair manual (tm2153)
John deere 500 buck utility atv service repair manual (tm2153)
 
John deere 315 d side shift loader service repair technical manual (tm1497)
John deere 315 d side shift loader service repair technical manual (tm1497)John deere 315 d side shift loader service repair technical manual (tm1497)
John deere 315 d side shift loader service repair technical manual (tm1497)
 

Recently uploaded

Basic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CBasic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CKapil Thakar
 
Automotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatAutomotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatKapil Thakar
 
Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Hyundai Motor Group
 
Car Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideCar Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideAskXX.com
 
CAMIONES TOYOTA N04C- Engine y HINO 300.
CAMIONES TOYOTA N04C- Engine y HINO 300.CAMIONES TOYOTA N04C- Engine y HINO 300.
CAMIONES TOYOTA N04C- Engine y HINO 300.JavierAlejandroCordo1
 
Why Won't Your Audi A3 Shift Into Reverse Gear Let's Investigate
Why Won't Your Audi A3 Shift Into Reverse Gear Let's InvestigateWhy Won't Your Audi A3 Shift Into Reverse Gear Let's Investigate
Why Won't Your Audi A3 Shift Into Reverse Gear Let's InvestigateAutowerks
 
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...Bijay Sharma
 
What Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsWhat Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsSchearer's Sales & Service Inc
 
Introduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceIntroduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceKapil Thakar
 
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerKapil Thakar
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceKapil Thakar
 
-VDA-Special-Characteristics Special characteristics.pdf
-VDA-Special-Characteristics Special characteristics.pdf-VDA-Special-Characteristics Special characteristics.pdf
-VDA-Special-Characteristics Special characteristics.pdfBorja ARRIZABALAGA URIARTE
 
Vina Score and Vin Min for almost all the models 2024
Vina Score and Vin Min for almost all the models 2024Vina Score and Vin Min for almost all the models 2024
Vina Score and Vin Min for almost all the models 2024jipohal318
 
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION .ppt
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION  .ppt5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION  .ppt
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION .ppthiren65650
 

Recently uploaded (14)

Basic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in CBasic of Firmware & Embedded Software Programming in C
Basic of Firmware & Embedded Software Programming in C
 
Automotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame FormatAutomotive Bootloader Complete Guide with UDS Frame Format
Automotive Bootloader Complete Guide with UDS Frame Format
 
Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'Quicker and better: South Korea’s new high-speed train 'EMU-320'
Quicker and better: South Korea’s new high-speed train 'EMU-320'
 
Car Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection GuideCar Seat Covers and Seat Protection Guide
Car Seat Covers and Seat Protection Guide
 
CAMIONES TOYOTA N04C- Engine y HINO 300.
CAMIONES TOYOTA N04C- Engine y HINO 300.CAMIONES TOYOTA N04C- Engine y HINO 300.
CAMIONES TOYOTA N04C- Engine y HINO 300.
 
Why Won't Your Audi A3 Shift Into Reverse Gear Let's Investigate
Why Won't Your Audi A3 Shift Into Reverse Gear Let's InvestigateWhy Won't Your Audi A3 Shift Into Reverse Gear Let's Investigate
Why Won't Your Audi A3 Shift Into Reverse Gear Let's Investigate
 
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...technical report on EV. EVs can offer benefitssuch as lower operating costs a...
technical report on EV. EVs can offer benefitssuch as lower operating costs a...
 
What Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission ProblemsWhat Should BMW Owners Know About Steptronic Transmission Problems
What Should BMW Owners Know About Steptronic Transmission Problems
 
Introduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS ServiceIntroduction to UDS over CAN | UDS Service
Introduction to UDS over CAN | UDS Service
 
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start TimerTimer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
Timer Handling in UDS | S3 Server Timer | P2 and P2 Start Timer
 
Introduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming SequenceIntroduction to Automotive Bootloader | Programming Sequence
Introduction to Automotive Bootloader | Programming Sequence
 
-VDA-Special-Characteristics Special characteristics.pdf
-VDA-Special-Characteristics Special characteristics.pdf-VDA-Special-Characteristics Special characteristics.pdf
-VDA-Special-Characteristics Special characteristics.pdf
 
Vina Score and Vin Min for almost all the models 2024
Vina Score and Vin Min for almost all the models 2024Vina Score and Vin Min for almost all the models 2024
Vina Score and Vin Min for almost all the models 2024
 
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION .ppt
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION  .ppt5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION  .ppt
5s-5S 5S 5S 5S 5S 5S 5S PRESENTATION .ppt
 

John deere 50 d compact excavator service repair technical manual (tm2264)

  • 1. TM2264 - 35D and 50D Excavator Fuel Injection Pump Remove and Install Fuel Injection Pump Remove and Install Fuel Injection Pump Remove 1. IMPORTANT: Never steam clean or pour cold water on injection pump while the pump is running or warm. Doing so can damage the pump. Clean injection lines and area around the injection pump with cleaning solvent or a steam cleaner. 2. Remove radiator, fan, and belt.  See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)  See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.) 3. Remove intake manifold. See Intake Manifold Remove and Install . (Group 0400.) 4. Lower air conditioning compressor. 5. RG13396A-UN: Remove Fuel Lines And Coolant Lines. 1/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 2. RG13397A-UN: Injection Pump Gear Cover RG13398A-UN: Injection Pump Gear Timing Marks LEGEND: A - Fuel Inlet Line B - Fuel Return Line C - Injector Return Line D - Coolant Line E - Coolant Line F - Fuel Shutoff Solenoid Wire Connector G - Foam Spacer H - Cap Screw (4 used) I - Pump Gear Timing Mark J - Idler Gear Timing Mark Disconnect fuel inlet line (A), fuel return line (B), and injector return line (C). 6. Disconnect coolant lines (D and E). 7. Disconnect fuel shutoff solenoid wire connector (F). 8. Remove foam spacer (G). 9. Remove cap screws (H) and remove injection pump gear access cover. 10. NOTE: For all the timing marks to become aligned, engine may need to be rotated up to fifty-two times. 2/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 3. Alignment marks (I and J) are both identified with a stamped letter “B”. Rotate engine in the direction of rotation until mark (I) on pump gear aligns with mark on idler gear (J) (both identified by a stamped letter B). Use chalk or paint to mark injection pump gear to idler gear. 11. RG13399A-UN: Injection Pump Timing Gear RG13400A-UN: Injection Pump Timing Gear Puller 3/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 4. TX1062018A-UN: Injection Pump Timing Marks LEGEND: A - Timing Gear Nut and Washer B - Cap Screw (4 used) C - Threaded Puller Holes D - Puller Cap Screw (2 used) E - Gear Puller F - Injection Pump Timing Mark G - Gear Cover Mounting Plate Timing Mark Remove gear retaining nut and washer (A). 12. IMPORTANT: Do not loosen or disturb cap screws (B) securing gear to the hub. Gear to hub adjustment is pre-set to comply with strict EPA emissions requirements and is not adjustable. This procedure is done at the pump manufacturer and cannot be duplicated in the field. Install puller (E) into threaded holes (C) on gear using cap screws (D). 13. IMPORTANT: Engine must not be rotated when timing gear is removed from injection pump shaft. Engine should only be rotated when timing gear is securely fastened to pump or engine damage could result. Remove gear and hub assembly from injection pump shaft. Gear will stay inside timing cover. 14. IMPORTANT: Marks must be made on the injection pump and the gear cover mounting plate to correctly install the pump. If marks are not made, there will be no way to properly time the injection pump. Note position of timing marks on gear cover mounting plate (G) and injection pump (F). Pump must be installed at the exact same timing mark as when removed. Scribe a line as accurately and straight as possible at the pump flange mark (F) onto the gear cover mounting plate. 4/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 5. 15. RG13402A-UN: Injection Pump Mounting Points LEGEND: A - External Lube Line B - Cap Screw C - Nut (3 used) Remove external lube line (A) from pump. 16. Remove cap screw (B). 17. IMPORTANT: Marks must be made on the injection pump and the gear cover mounting plate to properly install pump. You must also record the injection pump timing number marked on the pump to correctly install the pump. If marks are not made and the timing number not recorded, there will be no way to properly time the injection pump. Remove pump flange mounting nuts (C) and remove pump. 18. NOTE: The injection pump timing number is stamped on the engine side of the fuel injection pump housing. Treat this number as though there is a decimal point between the two digits. (Example 68 = 6.8). Find and record pump timing number stamped on pump. This number will be needed if pump is being replaced or recalibrated. IMPORTANT: DO NOT attempt to service the injection pump or governor. If unit is in need of repair, it must be serviced by a qualified EPA/CARB certified fuel injection repair shop. If replacement is necessary, replace entire unit. Do not rotate engine while injection pump is removed. If engine is rotated, the timing gear cover must be removed to ensure correct timing. Pump Installation 5/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 6. 1. RG13399A-UN: Injection Pump Timing Gear LEGEND: A - Timing Gear Nut and Washer B - Cap Screw (4 used) C - Threaded Puller Holes Install new O-ring on injection pump. 2. Put injection pump onto back of gear cover mounting plate. Install three mounting nuts. Do not tighten. Align key on shaft with keyway in gear hub. Ensure gear is still aligned to idler gear. 3. Install nut and washer (A) on pump shaft. Tighten nut to specification. 4. TX1062057A-UN: Injection Pump Timing Marks Item Measurement Specification Fuel Injection Pump Drive Gear Hub-to-Shaft Retaining Nut Torque 78—88 N˙m 58—65 lb-ft 6/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 7. RG13415A-UN: Injection Pump Mounting LEGEND: A - Injection Pump Timing Mark B - Gear Cover Mounting Plate Timing Mark C - Pump Mounting Nut (3 used) D - Cap Screw E - External Lube Line Align timing mark on injection pump (A) with correct mark on gear cover mounting plate (B). 5. Tighten three pump mounting nuts (C) to specification. 6. Install cap screw (D). Tighten to specification. 7. Fill pump with engine oil through external lube line port until oil runs out. Install external lube line. Tighten lube line fitting (E) to specification. 8. Install cover for injection pump timing gear. Item Measurement Specification Injection Pump Mounting Nuts Torque 26 N˙m 228 lb-in. Item Measurement Specification Injection Pump Mounting Cap Screw Torque 26 N˙m 228 lb-in. Item Measurement Specification Injection Pump External Lube Line Fitting Torque 15 N˙m 133 lb-in. 7/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 8. 9. RG13396A-UN: Install Fuel and Coolant Lines LEGEND: A - Fuel Inlet Line B - Fuel Return Line C - Injectors Return Line D - Coolant Line E - Coolant Line F - Fuel Shutoff Solenoid Wire Connector G - Foam Spacer Install spacer (G) between pump and engine block. 10. Connect fuel shutoff solenoid wire connector (F). 11. Connect fuel lines (A, B, and C). 12. Connect coolant lines (D and E). 13. Install intake manifold. See Intake Manifold Remove and Install . (Group 0400.) 14. Install radiator, fan, and belt.  See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)  See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.) New, Rebuilt, or Recalibrated Pump Timing 8/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 9. 1. RG13614-UN: Injection Pump Sticker LEGEND: A - Middle 0° Line B - 1° Line C - 2° Line D - 0.5° Line Install timing mark sticker supplied with pump so that the (A) line is exactly in-line with the mark that was made on the gear cover mounting plate when the pump was removed. 2. IMPORTANT: Injection pump timing can not be performed without injection pump timing numbers from original and replacement pumps. There is no way to properly install the injection pump without these numbers. Calculate the difference between the timing numbers, recorded earlier, from the original and replacement/recalibrated pumps. This calculated number will be needed to correctly time the pump. Example: If the timing number on the replacement/recalibrated pump was 6.0, and the timing number on the original pump is 4.0 (fuel injection angle of replacement/recalibrated pump) - (fuel injection angle of original pump), the replacement pump should be timed at the +2.0° (advanced) mark (C) on the new timing mark sticker. 3. NOTE: Rotating the injection pump away from the cylinder block will advance the timing and rotating the injection pump toward the cylinder block will delay the timing. Set the pump to the correct timing mark using the calculated number difference between the original and replacement pumps. Adjust timing accordingly using the new timing mark sticker. 4. Hold the pump at the correct timing mark and tighten three pump mounting nuts and cap screw to specification. 9/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 10. 5. If removed, install timing cover. See Timing Gear Cover Remove and Install . (Group 0400.) 6. RG13396A-UN: Install Fuel And Coolant Lines LEGEND: A - Fuel Inlet Line B - Fuel Return Line C - Injectors Return Line D - Coolant Line E - Coolant Line F - Fuel Shutoff Solenoid Wire Connector G - Foam Spacer Install spacer (G) between pump and engine block. 7. Connect fuel shutoff solenoid wire connector (F). 8. Connect fuel lines (A, B, and C). 9. Connect coolant lines (D and E). 10. Install intake manifold. See Intake Manifold Remove and Install . (Group 0400.) 11. Install radiator, fan, and belt.  See Radiator Remove and Install—35D (S.N. —254999) . (Group 0510.)  See Radiator Remove and Install—35D (S.N. 255000— ) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. —274999) . (Group 0510.)  See Radiator Remove and Install—50D (S.N. 275000— ) . (Group 0510.) Item Measurement Specification Injection Pump Mounting Nuts Torque 26 N˙m 228 lb-in. Injection Pump Mounting Cap Screw Torque 26 N˙m 228 lb-in. OUO1030,00000CA-19-20090721 10/10 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 11. TM2264 - 35D and 50D Excavator Fuel Injection Nozzles Remove and Install Fuel Injection Nozzles Remove and Install General Nozzle Service Precautions Before removal, thoroughly remove all dirt from the cylinder head around fuel injection nozzles. Clean with compressed air to prevent dirt from entering the cylinders. Plug the bore in the cylinder head after each nozzle has been removed. Cap fuel line openings as soon as they are disconnected. Immediately fit protective caps over the nozzle tips and the line connections to avoid handling damage and getting debris in fuel system. Do not bend the fuel delivery lines, as this may affect their durability. When loosening the fuel pressure lines, hold male union of nozzle line stationary with a backup wrench. 1. IMPORTANT: Never steam clean or pour cold water on injection pump while the pump is running or warm. Doing so can damage the pump. Clean the injection pump lines and area around the nozzles using a parts cleaning solvent or steam cleaner. NOTE: Nozzles are matched to the cylinders. If removing more than one nozzle, tag each nozzle, according to the cylinder from which it was removed. 1/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 12. 2. RG13407-UN: Fuel Injector Components LEGEND: A - Cap Screw and Washer B - Retaining Plate C - Hose Clamp D - Leak-Off Hose E - Injection Nozzle F - Ring G - Heat Protector Loosen fuel injection line connectors-to-nozzles slightly to release pressure in the fuel system. 3. Loosen line clamp(s) and remove fuel injection lines. 4. Remove clamps (C) and leak-off hoses (D). 5. Remove cap screw and washer (A) and retaining plate (B). 6. Remove injection nozzle (E), ring (F), and TEFLON ® heat protector (G). If ring and protector stay in cylinder head, thread a cap screw into protector and pull from cylinder head. 2/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 13. 7. M82126A-UN: If Nozzles Stick in Cylinder Head LEGEND: A - Large Flat Washer B - Nut (2 used) C - Cap Screw D - Old Injection Line Nut E - Injection Nozzle If nozzles are stuck in cylinder head: Grind the head of a cap screw (C) so it fits inside a nut from an old injection line (D). Use two nuts (B) to attach a large flat washer (A) to the cap screw. Install assembly onto nozzle and use a puller and slide hammer to pull nozzle from cylinder head. 8. Test injection nozzles. Perform Fuel Injection Nozzle Check . (Group 9010-25.) 9. Installation is done in the reverse order of removal. 10. Tighten retaining plate nuts. Item Measurement Specification Fuel Injection Retaining Plate Cap Screw Torque 24—28 N˙m 212—248 lb-in TEFLON is a trademark of Du Pont Co. OUO1030,00000CB-19-20051128 3/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 14. TM2264 - 35D and 50D Excavator Fuel Injection Nozzles Disassemble and Assemble Fuel Injection Nozzles Disassemble and Assemble Fuel Injection Nozzles Disassemble RG11097A-UN: Hole-Type Nozzle LEGEND: A - Injector Body B - Shims C - Spring D - Spring Seat E - Separator Plate F - Nozzle Valve G - Nozzle Body H - Retaining Nut I - Index Pin (2 used) NOTE: If servicing more than one nozzle, keep parts for each nozzle separate from one another. 1. Disassemble fuel injection nozzles. 1/5 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 15. 2. IMPORTANT: If injection nozzles are disassembled to be cleaned, the same number and thickness of shims must be installed. Clean and inspect nozzle components. Fuel Injection Nozzles Clean and Inspect 2/5 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 17. M82326B-UN: Nozzle Body, Separator Plate, Contact & Sealing Surfaces LEGEND: A - Injector Body B - Fuel Return Pipe C - Shims D - Spring E - Index Pin F - Separator Plate G - Nozzle Body H - Nozzle Valve I - Retaining Nut J - Spring Seat K - Nozzle Contact Surfaces L - Sealing Surfaces NOTE: To clean nozzles properly, JDF13B Nozzle Cleaning Kit is recommended. The cleaning kit is available through the John Deere SERVICEGARD ™ Catalog. 1. Remove anti-corrosive grease from new or reconditioned nozzles by washing them thoroughly in diesel fuel. 2. IMPORTANT: Never use a steel brush to clean nozzles as this will distort the spray hole. Remove carbon from used nozzles, and clean by washing in diesel fuel. If parts are coated with hardened carbon or lacquer, it may be necessary to use a brass wire brush (supplied in nozzle cleaning kit). 3. After removing carbon or lacquer from the exterior of nozzle, inspect sealing surfaces between separator plate and nozzle body for nicks or scratches. 4. Inspect condition of separator plate and nozzle body. Contact area of separator plate (both parts) must not be scored or pitted. Use an inspection magnifier to aid in making the inspection. 5. Check nozzle contact surface on separator plate for wear. If contact surface is more than specification, replace nozzle assembly. 6. Inspect the piston (large) part of nozzle valve to see that it is not scratched or scored and that lower (tip) end of valve is not broken. If any of these conditions are present, replace the nozzle assembly. Item Measurement Specification Fuel Injection Nozzle Contact Surface Size 0.10 mm 0.0039 in. 4/5 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 18. 7. M35919-UN: Nozzle Valve & Body LEGEND: A - Nozzle Valve B - Nozzle Body Further inspect the nozzle assembly by performing a slide test. Use the following procedure: a. Dip the nozzle valve in clean diesel fuel. Insert valve (A) in nozzle body (B). b. Hold nozzle vertical, and pull valve out about 1/3 of its engaged length as shown. c. Release valve. Valve should slide down to its seat by its own weight. Replace nozzle assembly if the valve does not slide freely to its seat. Fuel Injection Nozzles Assemble 1. Assembly is done in the reverse order of disassembly. 2. Tighten retaining nut (H) to specification. 3. After assembly is complete, test injection nozzle. Perform Fuel Injection Nozzle Check . (Group 9010-25.) Item Measurement Specification Fuel Injection Nozzle Retaining Nut Torque 43 N˙m 31 lb-ft SERVICEGARD is a trademark of Deere & Company. OUO1030,00000CC-19-20051128 5/5 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 19. TM2264 - 35D and 50D Excavator Rocker Arm Cover Remove and Install Rocker Arm Cover Remove and Install RG13393-UN: Rocker Arm Cover LEGEND: A - Special Nut (3 used) B - Diaphragm Cover C - Spring D - Diaphragm E - Oil Filler Cap F - Gasket G - Baffle H - Baffle Plate I - Gasket J - Rocker Arm Cover K - Crankcase Breather Tube L - O-Ring 1/2 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 20. M - Spring Plate 1. Remove the special nuts (A). 2. Disconnect crankcase breather tube (K). 3. Remove rocker arm cover (J) from cylinder head. 4. Remove diaphragm cover (B). 5. Remove and inspect spring (C) and diaphragm (D). Replace if damaged or deteriorated. 6. Remove baffle plate (H) and baffle (G). 7. Wash baffle in solvent and blow dry with compressed air. Replace baffle if it is damaged or deteriorated. 8. Install baffle and baffle plate. 9. Install diaphragm, spring plate (M), spring, and diaphragm cover. 10. Inspect gasket (I) and O-rings (L) before reinstalling rocker arm cover. Replace if damaged. 11. Clean cylinder head surface and install rocker arm cover on cylinder head. Install special nuts and tighten to specification. Item Measurement Specification Rocker Arm Cover Special Nuts Torque 18 N˙m 156 lb-in. OUO1030,000006C-19-20051128 2/2 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 21. TM2264 - 35D and 50D Excavator Rocker Arm Shaft Assembly Repair Rocker Arm Shaft Assembly Repair Rocker Arm Shaft Disassemble 1. RG13416-UN: Rocker Arm Shaft Assembly LEGEND: A - Nut B - Adjusting Screw C - Mounting Cap Screw D - Nut E - Stud F - Rocker Arm End Support G - Rocker Arm Shaft H - Push Rod I - Valve Cap J - Intake Valve Rocker Arm K - Exhaust Valve Rocker Arm L - Mounting Cap Screw M - Rocker Arm Shaft Spring N - Rocker Arm Center Support Remove rocker arm cover. See Rocker Arm Cover Remove and Install . (Group 0400.) 2. Remove rocker arm end support mounting cap screws (C). 3. Remove rocker arm center support mounting cap screws (L). 4. Lift rocker arm assembly from cylinder head and set on bench. 5. NOTE: When disassembling the rocker arm assembly, replace components in same location on rocker arm shaft they were removed from. Slide rocker arm assembly components off rocker arm shaft while noting positions for reassembly. 6. Lift push rods (H) from cylinder head and note order of removal for reassembly in same positions in head. Rocker Arm Shaft Inspect 1. M35262A-UN: Measure Rocker Arm Shaft Outer Diameter 1/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 22. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.
  • 23. M82022A-UN: Measuring Rocker Arm ID LEGEND: A - Rocker Arm Shaft B - Rocker Arm Measure outer diameter of rocker arm shaft (A) at each rocker arm location. Replace rocker arm shaft if less than wear limit. 2. Measure inner diameters of rocker arms (B) and supports. Replace rocker arms or supports if ID is more than wear limit. 3. M82023A-UN: Measure Length and Bending of Push Rod LEGEND: A - Push Rod Length B - Push Rod Bend Measure length (A) and bending (B) of push rod. Replace push rod if not within specifications. Item Measurement Specification Rocker Arm Shaft OD 15.97—15.98 mm 0.6286—0.6293 in. Wear Limit 15.95 mm 0.6280 in. Item Measurement Specification Rocker Arm Shaft Support ID 16.00—16.02 mm 0.630—0.631 in. Wear Limit 16.09 mm 0.633 in. Rocker Arm Shaft-to-Rocker Arm and Shaft Support Clearance Wear Limit 0.14 mm 0.006 in. Item Measurement Specification Push Rod Length 178.2—178.75 mm 7.018—7.037 in. Push Rod Bend Wear Limit 0.03 mm 0.001 in. 2/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 24. Rocker Arm Shaft Assemble 1. NOTE: Lubricate all parts with clean oil during assembly. Install push rods in cylinder head with ball-shaped end down in head. Push rods should be in same locations they were removed from. 2. Assemble rocker arm assembly components in the reverse order of removal. 3. Place rocker arm assembly on cylinder head. Align rocker arms with valves and push rods. Align rocker arm end supports and center supports with corresponding holes in head. 4. Install rocker arm support mounting cap screws and torque to specification. 5. Adjust valve clearance. See Engine Valve Lash (Clearance) Check and Adjustment . (Group 9010-25.) Item Measurement Specification Rocker Arm Support Cap Screws Torque 26 N˙m 230 lb-in. OUO1030,000006F-19-20060105 3/3 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...
  • 25. TM2264 - 35D and 50D Excavator Cylinder Head Remove and Install Cylinder Head Remove and Install Cylinder Head Remove T207557-UN: Cylinder Head Remove and Install 1/8 2019/11/19file:///C:/ProgramData/Service%20ADVISOR/Temp/TM2264_09001faa802a...