This document provides instructions for assembling the input shaft and forward clutch of a backhoe loader reverser. The steps include installing bearings, packings, snap rings, pressure plates, disks, springs, and sealing rings. Clearances and thicknesses are specified. Proper alignment of keys and splines is important. Lubrication with petroleum jelly is noted to prevent damage to sealing rings during assembly.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
John Deere 310D Backhoe Loaders Service Repair Technical Manual (TM1497).pdf
1. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Service Equipment And Tools
Service Equipment And Tools
NOTE:
Order tools from the SERVICEGARD ™ Catalog or from the European Microfiche Tool Catalog (MTC).
Some tools may be available from a local supplier.
Bushing, Bearing and Seal Driver Set
To remove and install seals and bearings.
Puller Set
To remove bearing cups and cones.
Differential Lifting Tool.......JT38000
To remove and install differential drive shaft.
Hydraulic Ram.......D01103AA
To install differential drive shaft.
Spacer....... [DFT1103Dealer Fabricated Tool, see Group
0399 for instructions to make tool.]
To install cluster gear on drive shaft.
Rivet Forming Tool....... [DFT1121Dealer Fabricated
Tool, see Group 0399 for instructions to make tool.]
To install differential ring gear rivets.
SERVICEGARD is a trademark of Deere & Company. TX, 03,DY56-19-1996/07/19
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129733.html
2. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Other Material
Other Material
Number Name Use
AT124243 (U.S.) SILASTIC 732 ® RTV Adhesive
Sealant
To assemble lube pump.
TY6305 (U.S.)
TY9485 (Canadian)
764 LOCTITE ® (LOCTITE®)
Clean and Cure Primer Products To clean transaxle cover, top of
transaxle case, ring gear and
differential housing.
TY6304 (U.S.)
TY9484 (Canadian)
515 LOCTITE ® (LOCTITE®)
Flexible General Purpose Sealant
Products
To seal lube pump joint and reverser
output shaft splines.
TY9375 (U.S.)
TY9480 (Canadian)
592 TEFLON ® (LOCTITE®)
Pipe Sealant with Products To seal MFWD transfer case quill
cap screws.
TY9370 (U.S.)
TY9477 (Canadian)
242 LOCTITE ® (LOCTITE®)
Thread Lock and Sealer (Medium
Strength) Products
To assemble lube pump and install
first and second shifter shaft plug
and set screws.
T43515 (U.S.)
TY9479 (Canadian)
635 LOCTITE ® (LOCTITE®)
Retaining Compound (Maximum
Strength) Products
To assemble ring gear to differential
housing.
SILASTIC is a registered trademark of the Dow-Corning Corp.
LOCTITE is a registered trademark of Loctite Corp.
TEFLON is a registered trademark of the DuPont Co. TX0350BD298-19-1993/04/06
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129735.html
3. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Specifications
Specifications
Item Measurement Specification
Reverser Input Shaft End Play 0.25-2.18 mm (0.010-0.86 in.)
Reverser Forward Clutch Pack Clearance 0.5-0.9 mm (.021-.036 in.)
Reverser Bearing Retainer Cap
Screws
Torque 57-68 N·m (42-50 lb-ft)
Reverse Output Yoke Nut Torque 102-115 N·m (75-85 lb-ft)
Reverser Front Cover Cap Screw Torque 37-50 N·m (27-37 lb-ft)
Reverser Charge Pump Cap Screw Torque 23-30 N·m (17-22 lb-ft)
Axle Weight 79 kg (175 lb)
Differential Assembly Weight 25 kg (55 lb)
Differential Assembly Cover Cap
Screws
Torque 47 N·m (35 lb-ft)
Differential Housing Preload 0.05-0.13 mm (0.002-0.005 in.)
Differential Drive Shaft: New
Bearings
Rolling Drag Torque 1-3 N·m (9-27 lb-in.)
Differential Drive Shaft: Used
Bearing (Nominal spec)
Rolling Drag Torque 0.5-2 N·m (4-18 lb-in.)
Differential Drive Shaft: Differential
Housing
Backlash 0.15-0.20 mm (0.006-0.008 in.)
Differential Drive Shaft: Differential
Bearing Quill Cap Screws
Torque 48 ± 5 N·m (35 ± 4 lb-ft)
Differential Drive Shaft:
Transmission Drive Shaft Front
Bearing Cone-to-Snap Ring
Maximum Gap 0.152 mm (0.006 in.)
Differential Drive Shaft:
Transmission Drive Shaft Quill Cap
Screws
Torque 47 N·m (35 lb-ft)
Differential Drive Shaft:
Transmission Drive Shaft
End Play 0.10-0.15 mm (0.004-0.006 in.)
Differential Drive Shaft: Shifter Shaft
Detent Ball Springs
Free length Test length 25.5 mm (0.96 in.) 16 mm at 133.5 ±
16 N (0.64 in. at 30 ± 3.5 lb)
Differential Drive Shaft: Driven Gear End Play 0.05-0.10 mm (0.002-0.004 in.)
Differential Drive Shaft: Output Shaft End Play 0.05-0.10 mm (0.002-0.004 in.)
Differential Drive Shaft: Idler Shaft
Retaining Strap Cap Screw
Torque 75 N·m (55 lb-ft)
Differential Drive Shaft: Drive Shaft
Quill Cap Screws
Torque 75 N·m (55 lb-ft)
页码,1/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129736.html
4. Differential Drive Shaft: Drive Shaft End Play 0.05-0.10 mm (0.002-0.004 in.)
Differential Drive Shaft: Drive Gear
Quill Cap Screw
Torque 72 N·m (53 lb-ft)
Differential Drive Shaft: Output Shaft
Quill Cap Screw
Torque 75 N·m (55 lb-ft)
Differential Drive Shaft: Transfer
Case to Transaxle Cap Screws and
Nuts
Torque 115 N·m (85 lb-ft)
Item Measurement Specification
Lube Pump
(SN -796033) Pump-to-
Transmission
Distance 96 mm (3.78 in.)
(SN 796034- ) Drive Shaft End Play 0.8-1.0 mm (0.03-0.04 in.)
Item Measurement Specification
Drive Shaft Lock Nut Torque 68 N·m (50 lb-ft)
Second Speed Gear-310D, 315D Minimum End Play 0.07 mm (0.003 in.)
TX0350BD326-19-1994/03/11
页码,2/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129736.html
5. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Reverser Repair Information
Reverser Repair Information
T7366BE-UN: Early Reverser Unit Shown
LEGEND:
A - Reverse Brake
B - Forward Clutch
C - Directional Control Valve
D - Planetary Assembly
E - Oil Pump
The main mechanical components of the reverser, reverse brake (A), forward clutch (B) and planetary assembly (D), are covered in this group.
For repair of the hydraulic components, directional control valve (C) and oil pump (E), refer to Group 0360.
For later reversers, the solenoid coils are mounted directly on the reverser case.
TX0350BD188-19-1993/04/06
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032018.html
6. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Remove And Disassemble Front Cover And Reverse Brake
Remove And Disassemble Front Cover And Reverse Brake
T6200AG-UN: Front Cover And Reverse Brake
LEGEND:
A - Screw (4 used)
B - Bushing
C - Cover
D - Gasket
E - Piston
F - Packing
页码,1/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032040.html
7. G - Pressure Plate
H - Dowel Pin (3 used)
I - Plate (3 used)
J - Disk (3 used)
K - Spring (11 used)
L - Packing
Inspect parts for wear or damage; replace as necessary.
Use a press to install new bushing (B) in front cover (C). Check inside diameter of bushing. Bushing should measure 34.93-34.95 mm (1.375-1.376 in.). If necessary, use a hone to obtain correct
diameter.
TX0350BD189-19-1993/04/06
页码,2/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032040.html
8. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Remove And Disassemble Input Shaft And Forward Clutch
Remove And Disassemble Input Shaft And Forward Clutch
T7518AA-UN: Legend For Input Shaft And Forward Clutch
页码,1/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032028.html
9. LEGEND:
A - Thrust Washer
B - Sealing Ring (2 used)
C - Shaft Key
D - Sealing Ring (2 used)
E - Snap Ring
F - Clutch Housing
G - Clutch Hub
H - Snap Ring
I - Pressure Plate
J - Disk (7 used)
K - Plate (6 used)
L - Pressure Plate
M - Snap Ring
N - Clutch Spring
O - Snap Ring
P - Bearing Ring
Q - Packing
R - Piston
S - Packing
T - Housing
U - Thrust Washer
V - Bearing
W - Snap Ring
X - Snap Ring
TXD300DS3094-19-1991/06/26
页码,2/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032028.html
10. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Remove Planetary Assembly And Bearing Retainer
Remove Planetary Assembly And Bearing Retainer
T7518AB-UN: Planetary Assembly And Bearing Retainer
LEGEND:
A - Nut
B - Washer
C - Yoke
D - Seal
E - Retainer
F - Gasket
G - Bearing
H - Sleeve
I - Housing
J - Bearing
K - Sealing Ring (2 used)
L - Planetary Assembly
M - Bearing
N - Baffle
TXD300DS3096-19-1991/06/26
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032024.html
11. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Assemble Input Shaft And Forward Clutch
Assemble Input Shaft And Forward Clutch
1.
T5983AN-UN: Bearing And Bearing Retainer Ring
Install bearing (A) and bearing retainer ring (B).
2.
T5983AO-UN: Packings And Bearing Bearing Ring
Put petroleum jelly on packings. Install packings (A and B).
3. Install piston. Be sure packings are not rolled or damaged when installing piston.
4. Install bearing bearing ring (C).
5.
T7509AV-UN: Pressure Plate/Area W/o Teeth/Lube Passages
Install pressure plate (A) with smooth side facing up.
6. IMPORTANT:
页码,1/5(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032029.html
12. DO NOT block three lube passages (B) when installing disks and plates.
Install seven disks and six plates. The area without teeth (C) on the disks must be installed over the lube passages (B).
7. Install top pressure plate with smooth side down.
8. IMPORTANT:
For correct operation, snap ring MUST be within tolerance.
T5983AR-UN: Measure Snap Ring Thickness
Measure snap ring thickness. Snap ring must be 2.3-2.4 mm (0.090-0.094 in.) thick.
9. NOTE:
Snap ring does not fit into a groove.
Install correct snap ring.
10.
T7509BB-UN: Clutch Spring And Piston Assembly
Install clutch spring (A) concave side down.
页码,2/5(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032029.html
13. 11. Install piston assembly (B) using a press.
12. IMPORTANT:
For correct operation, snap ring MUST be within tolerance.
T5983AS-UN: Measure Snap Ring Thickness
Measure snap ring thickness. Snap ring must be 1.9-2.0 mm (0.074-0.078 in.) thick.
13. Use a press to move housing enough to install snap ring into groove. Turn housing over and seat housing against snap ring using a
brass drift.
14. IMPORTANT:
For correct clutch operation, end play between rear pressure plate and lip in the housing must be correct.
T5985AP-UN: Use A Feeler Gauge To Measure The Distance
Push rear pressure plate down evenly with approximately 44.5 N (10 lb) force to remove all space between disks. Use a feeler gauge
to measure the distance between rear pressure plate and lip.
15. Install correct snap ring or combination of snap rings to reduce clutch pack clearance to 0.5-0.9 mm (0.021-0.036 in.).
Two thin snap rings may be used to obtain proper clutch pack clearance.
16. NOTE:
Selective snap rings have a free diameter of approximately 145.5 mm (5.68 in.). Snap rings are colored-coded to
help identify the thickness of each snap ring. Use table below as a guide.
Item Measurement Specification
Clutch Pack Clearance 0.5-0.9 mm (0.021-0.036 in.)
页码,3/5(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032029.html
14. T5985AO-UN: Correct Snap Ring
Install correct snap ring (A).
17. IMPORTANT:
Shaft key (A) and key way must be aligned.
T5983AG-UN: Shaft Key
Install shaft key (A).
18. Use a press and a 2.0 ID x 2.375 OD x 8.00 in. long piece of round tubing to install gear.
19. IMPORTANT:
To prevent damage to sealing rings (A) during assembly, use petroleum jelly to hold rings in grooves.
Item Measurement Specification
Snap Rings-Green Thickness 1.3-1.4 mm (0.059-0.054 in.)
Snap Rings-Purple Thickness 1.5-1.6 mm (0.062-0.066 in.)
Snap Rings-Orange Thickness 1.7-1.9 mm (0.074-0.078 in.)
Snap Rings-Blue Thickness 2.1-2.2 mm (0.084-0.088 in.)
Snap Rings-White Thickness 2.4-2.5 mm (0.096-0.100 in.)
Snap Rings-Green and Orange Thickness 3.0-3.3 mm (0.124-0.132 in.)
页码,4/5(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032029.html
15. T5984AA-UN: Sealing Rings And Snap Rings
Put petroleum jelly on sealing rings. Install snap ring (B) and sealing rings (A and C). Be sure sealing rings turn freely and do not bind
in shaft grooves.
20.
T5984AB-UN: Input Shaft
Install input shaft. Turn shaft to align splines of clutch hub with splines of disks.
21. Install bearing with a press and a 1.625 ID x 2.00 OD x 8.00 in. long piece of round tubing.
22.
T5988AA-UN: Snap Rings
Install snap rings (A and B).
TXD300DS3097-19-1991/06/26
页码,5/5(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032029.html
16. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Assemble Bearing Retainer
Assemble Bearing Retainer
1.
T5988AB-UN: Oil Seal
Install new oil seal using a press and 53 mm and 77 mm disks. Install seal tight against retainer shoulder.
2.
T7971AS-UN: Ball Bearing In Bearing Retainer
Install ball bearing in bearing retainer.
TXD300DS3108-19-1991/06/26
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129759.html
17. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Install Bearing Retainer
Install Bearing Retainer
1.
T5988AD-UN: Sleeve
Install sleeve using a press and 69 mm and 90 mm disks. Install sleeve tight against housing shoulder.
2.
T5988AE-UN: Gasket
Install new gasket (A).
3. Install retainer and cap screws. Tighten cap screws to 57-68 N·m (42-50 lb-ft).
Item Measurement Specification
Reverser Bearing Retainer Cap
Screws
Torque 57-68 N·m (42-50 lb-ft)
TXD300DS3110-19-1991/06/26
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXTX0354319990129762.html
18. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Install Planetary Assembly
Install Planetary Assembly
1. Install new needle bearing (A) to same depth as old needle bearing.
2. Install baffle (B).
3.
T5988AG-UN: Planetary Assembly
Install planetary assembly.
4.
T7971AT-UN: Output Shaft Yoke, Washer And Nut
Install output shaft yoke (A), washer (B) and nut (C) on opposite end of planetary assembly. Tighten nut.
5. Remove nut and washer. Fill cavity between washer and end of output shaft with Gasket Maker to seal grooves of spline.
6. Install washer and nut. Tighten nut to 102-115 N·m (75-85 lb-ft).
Item Measurement Specification
Reverser Output Yoke Nut Torque 102-115 N·m (75-85 lb-ft)
TXD300DS3112-19-1991/06/26
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032025.html
19. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Install Input Shaft And Forward Clutch
Install Input Shaft And Forward Clutch
T7509AY-UN: Clutch Assembly
1. Install thrust washer.
2. Turn clutch assembly (A) when installing to align gear teeth. Use care to prevent damage to sealing rings.
TXD300DS3114-19-1991/06/26
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032030.html
20. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Assemble And Install Reverse Brake And Front Cover
Assemble And Install Reverse Brake And Front Cover
1.
T5988AH-UN: Thrust Washer, Dowel Pins And Springs
Install thrust washer (C).
2. Install three dowel pins (B) in slots in housing.
3. Install eleven springs (A).
4. IMPORTANT:
When viewing the reverser from the input shaft side, install off set tabs (C) over dowel pin (D) at the 7:00
o-clock position.
Install the widest ear of the tab to the right side of the dowel pin.
页码,1/3(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032041.html
21. T5983AI1-UN: Disks, Plates & Off Set Tabs Over Dowel Pin
Put clean oil on disks. Install three disks (A) and three plates (B) as shown. Assemble odd-shaped lug over dowel as
shown.
5.
T5988AI-UN: Press Plate W/’V’ Slot Aligned W/large Oil Hole
Install pressure plate with "V" slot (B) of pressure plate aligned with large oil hole (A) at top of case.
页码,2/3(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032041.html
22. 6.
T5983AM-UN: Packings
Install new packings (A and B). Put petroleum jelly on packings.
7. Install piston.
8.
T5988AS-UN: Gasket
Install new gasket.
9. Install cover and cap screws. Tighten cap screws to 37-50 N·m (27-37 lb-ft).
Item Measurement Specification
Reverser Front Cover Cap Screws Torque 37-50 N·m (27-37 lb-ft)
TXD300DS3115-19-1991/06/26
页码,3/3(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUTX5511998032041.html
23. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Transaxle-300D
Transaxle-300D
T8303AE-UN: Transaxle Diagram
LEGEND:
A - Pump Outlet to Cooler
B - Pump Outlet Line
C - Lube Pump
D - Drive Shaft Sleeve
E - Clamp
F - Pump Drive Shaft
G - Spring Pin
H - Lube Trough
I - Third and Fourth Gear Synchronizer
J - Transmission Drive Shaft
K - Differential Drive Shaft
L - Case Inlet from Cooler
M - Shift Collar
N - Inlet Line to Brake Cavity
页码,1/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUO104719980601121.html
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. O - Ring Gear
P - Parking Brake Band
Q - Suction Line
R - Pump Support Bracket
S - Pin
T - Lube Pump with Spline
U - Adjustment Sleeve
V - Lock Nut
W - Sleeve
TX0315BA1478-19-1994/09/12
页码,2/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUO104719980601121.html
26. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Transaxle-310D, 315D (SN -796033)
Transaxle-310D, 315D (SN -796033)
T7511AA-UN: Transaxle Diagram
LEGEND:
A - Pump Outlet to Cooler
B - Pump Outlet Line
C - Lube Pump
D - Clamp
E - Drive Shaft Sleeve
F - Pump Drive Shaft
G - Spring Pin
H - Lube Trough
I - Third and Fourth Gear Synchronizer
J - Transmission Drive Shaft
K - Differential Drive Shaft
L - Case Inlet from Cooler
M - First and Second Gear Synchronizer
N - Inlet Line to Brake Cavity
O - Ring Gear
P - Parking Brake Band
Q - Suction Line
R - Pump Support Bracket
S - Pin
TX0350DS3529-19-1994/07/12
页码,1/1(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUO104719980601122.html
27. tm1497 - 300D, 310D, 315D Backhoe Loaders Repair
Transaxle-310D, 315D (SN 796034- )
Transaxle-310D, 315D (SN 796034- )
T8303AF-UN: Transaxle Diagram
LEGEND:
A - Pump Outlet to Cooler
B - Pump Outlet Line
C - Lube Pump
D - Clamp
E - Drive Shaft Sleeve
F - Pump Drive Shaft
G - Spring Pin
H - Lube Line
I - Third and Fourth Gear Synchronizer
J - Transmission Drive Shaft
K - Differential Drive Shaft
L - Case Inlet from Cooler
M - First and Second Gear Synchronizer
N - Inlet Line to Brake Cavity
页码,1/2(W)
w
4/24/2020
file://C:ProgramDataService ADVISORTemptm1497_TXOUO1047199806025.html