This document provides an introduction and safety checklist for a service manual for a JCB ZT 20D machine. It begins with copyright information and discusses the purpose and contents of the service manual. It then provides information on identifying the specific machine, including identification plates for the machine, engine, hydraulic pumps, and wheel motors. Tool and torque specifications are listed, as well as recommended sealing and retaining compounds. The safety notices section provides definitions for different safety signal words and emphasizes the importance of understanding and following all safety precautions in the manual and on the machine.
The safety checklist section continues discussing safety responsibilities and provides reminders to always think of potential hazards and how to avoid them. It stresses the importance of proper training, personal
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fjsekdhjenmdn
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)dfjjsjkemmm
This document provides information about identifying JCB machines, including identification plates, vehicle identification numbers, product identification numbers, and engine identification. It discusses data plates, typical VIN and PIN formats, and labels for ROPS, TOPS, and FOGS structures. Safety warnings are provided about not modifying or improperly repairing ROPS, TOPS, and FOGS structures.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)dfjjsjkemmm
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fjskekfmsmeer
This document provides information about identifying JCB machines, including identification plates, vehicle identification numbers, product identification numbers, and engine identification. It discusses data plates, typical VIN and PIN formats, and labels for ROPS, TOPS, and FOGS structures. Safety warnings are provided about not modifying or improperly repairing ROPS, TOPS, and FOGS structures.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)fujsjefkskem
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be mixed with other fastener types.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)fjskekfmsmeer
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be mixed with other fastener types.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fusjefkskemme
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also defines zinc plated and Dacromet fasteners and notes they have different torque settings.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fujsjefkskem
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fjsekdhjenmdn
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)dfjjsjkemmm
This document provides information about identifying JCB machines, including identification plates, vehicle identification numbers, product identification numbers, and engine identification. It discusses data plates, typical VIN and PIN formats, and labels for ROPS, TOPS, and FOGS structures. Safety warnings are provided about not modifying or improperly repairing ROPS, TOPS, and FOGS structures.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)dfjjsjkemmm
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fjskekfmsmeer
This document provides information about identifying JCB machines, including identification plates, vehicle identification numbers, product identification numbers, and engine identification. It discusses data plates, typical VIN and PIN formats, and labels for ROPS, TOPS, and FOGS structures. Safety warnings are provided about not modifying or improperly repairing ROPS, TOPS, and FOGS structures.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)fujsjefkskem
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be mixed with other fastener types.
Jcb 8055 midi excavator service repair manual (serial number 1536000 onwards)fjskekfmsmeer
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be mixed with other fastener types.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fusjefkskemme
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also defines zinc plated and Dacromet fasteners and notes they have different torque settings.
Jcb 8065 midi excavator service repair manual (serial number 1537500 onwards)fujsjefkskem
This document provides information about identifying machines, standard torque settings, and fastener types for a JCB service manual. It describes identifying marks like data plates, vehicle identification numbers, and engine identification. It provides tables listing torque specifications for UNF and metric grade bolts and fasteners under lubricated and unlubricated conditions. It also identifies zinc-plated and Dacromet fasteners and notes that Dacromet fasteners have lower torque settings and should not be used with zinc-plated nuts or bolts.
This document is a table of contents for the engine, fuel, and exhaust systems of Massey Ferguson 1648, 1652, and 1655 compact tractors. It contains 91 pages listing component part numbers and references for the various engine systems of the different tractor models. The pages are organized by component and sub-component and include items like the cylinder block, heads, manifolds, pumps, nozzles and tanks.
This document provides parts information for the cylinder head, rocker shaft, crankshaft, pistons, and connecting rods of a Massey Ferguson 365 tractor engine. It includes the part numbers, quantities, descriptions, and other details for 33 relevant parts. Footnotes provide additional specification details or replacement part numbers for some items. The document is intended to aid in servicing and repairing these core engine components.
JCB WLS 432ZX Wheeled Loader Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides a summary of a service manual for a WLS 432ZX machine. It includes sections on general information, care and safety, maintenance, and specific components like the body and framework, hydraulics, transmission, and brakes. It specifies that only JCB approved replacement parts should be used. Various service tools are also described that are required for tasks like installing glass, cutting out broken glass, and setting up pivots. Torque settings are provided for common metric bolt sizes. Colour codes are also defined for diagrams depicting hydraulic system pressures and flows.
Massey Ferguson MF155 MF158 TRACTOR Parts Catalogue Manual Instant Download.pdfid9sodkdkmdm
This document provides a parts list and diagrams for the engine and various systems of a Massey Ferguson 155/158 tractor. It includes over 35 individual items related to the engine, electrical equipment, alternator, generator, starter, and other components. Each item lists the part number, quantity, description, and any relevant comments to identify variations or component numbers. The document aims to catalog all relevant parts for servicing and repair of this tractor model.
JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides a numerical list of service tools required for procedures in the manual. The list includes tools for sections on body and framework (B), electrics (C), and hydraulics (E). Specific tools are not listed, but are available as kits that can be found in the tool detail reference section. General workshop tools are also expected to be available.
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and related systems, including the cylinder block, crankshaft, cylinder head, rocker arm assembly, and other components. Each part is given an item number, part number, quantity, description, and in some cases additional comments or part number variants. Diagrams illustrate the layout and components of the engine systems.
The document contains technical specifications and diagrams for a Massey Ferguson MF 2620 tractor. It lists over 100 individual parts that make up the engine, cylinder block, rocker arm, cylinder head, crankshaft, and cylinder head cover. The parts are organized numerically and include the part number, quantity, description, and any relevant comments for each component.
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2620 tractor, including the engine, cylinder block, flywheel housing, crankshaft, pistons, connecting rods, and cylinder head. Each component lists the relevant part numbers, quantities, descriptions, and any additional comments. Serial numbers and engine numbers are referenced for certain part applicability.
This document provides a parts list and descriptions for servicing the engine of a Massey Ferguson 275 tractor. It lists 31 individual parts needed for the engine, including the cylinder block, crankshaft, pistons, connecting rods, gears, and other components. Each part is identified by a part number, quantity needed, description, and any relevant comments. The list separates parts for different engine types and model years.
This document contains lists of components for engine repair or replacement. It includes items like cylinders, crankshafts, connecting rods, pistons, gaskets, screws, sensors and other parts. Quantities and references are provided for each component. Applications are for F/XL Tier 2 tractors from 2003-2008.
Massey Ferguson MF 396 C CRAWLER (IT) Parts Catalogue Manual Instant Download...id9sodkdkmdm
This document contains parts lists and assembly details for the engine of a Massey Ferguson MF 396 C Crawler excavator. It includes lists of parts for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and rocker shaft assembly. Quantities, part numbers, and other identifying information are provided for each part.
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2680 tractor engine. It includes 44 items that make up the cylinder block, 12 items for the flywheel housing, and numerous other parts grouped into sections for the crankshaft, cylinder head, rocker shaft, and other engine systems. Each item lists the part number, quantity, description, and any replacement or additional part information.
JCB VIBROMAX 255 265 TANDEM ROLLER Service Repair Manual Instant Download.pdfid9sodkdkmdm
This service manual provides information on the 255/265 tandem roller including:
1) The machine uses a Kubota diesel engine and hydrostatic drive system to power drums or pneumatic tires for compaction.
2) Safety features and procedures are outlined covering general operation, maintenance, and personal protective equipment.
3) Systems covered include propulsion, vibration, steering, brakes, hydraulics, electrical, and attachments.
JCB Transmissions Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides an overview and instructions for using a service manual for JCB transmissions. It includes a scope section describing the modular structure of the manual and applicable axle and gearbox assemblies. Tables list the relevant procedure sections for dismantling, inspecting and assembling components for different JCB machine models. Information is also provided on torque settings, service tools, and sealing compounds to aid in repair work. The document aims to guide users to the appropriate sections for servicing specific transmission components across JCB's product lines.
This document provides part numbers and descriptions for replacement parts for a Massey Ferguson MF 675 tractor from 1984. It includes lists of parts for the engine accessories, guards, fan, cylinder block, crankshaft and connecting rods, cylinder head, flywheel, and front end drive input and output. Each item lists the part number, quantity, description, and any comments about the part.
This document provides information about identifying a JCB TM310 machine, including its components. It discusses the machine identification plate containing serial numbers for the machine and major units. It also describes typical product identification numbers (PIN), vehicle identification numbers (VIN), and identification plates for the engine, transmission, drop box, and axle. Component plates contain serial numbers and information about the type, model, and year of manufacture. The identification and serial numbers can be used to properly identify the specific machine and order correct replacement parts.
This document is the service manual for JCB machines TM180/220. It provides instructions for servicing and repairing these machines. The manual is organized into multiple sections covering general information, safety, maintenance procedures, and technical information on specific components and systems. Technicians are instructed to follow all safety procedures and only perform work on the specific machine models listed in the applications tables at the front of each section. The format and organization of the manual is described to help technicians find the correct information for the maintenance or repair tasks.
McCormick MTX Series (2002-2007) - MTX3 - MTX110, MTX125, MTX140 Parts Catalo...id9sodkdkmdm
This document contains parts listings and diagrams for engine components of McCormick MTX Series tractors from 2002-2007, including the MTX3, MTX110, MTX125 and MTX140 models. It lists over 50 individual part numbers, descriptions and quantities for items such as an engine assembly, radiator, hoses, bolts, seals, brackets and other engine parts. The document provides replacement part information for work on engine systems.
This document contains parts lists and repair instructions for engine components. It lists 54 individual parts for a kit labeled ZZ50312, including blocks, caps, plugs, dowels, and screws. It also provides information on replacement parts, repair times, and part numbers.
This document contains parts lists and repair instructions for engine components. It lists part numbers, descriptions, and repair times for replacing components like pistons, connecting rods, cylinder heads, valves, rocker arms, and more. The parts are for McCormick tractors from model years 2003-2008. Replacement times are provided in hours, and parts are identified as wear items that require replacement during an overhaul.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
This document is a table of contents for the engine, fuel, and exhaust systems of Massey Ferguson 1648, 1652, and 1655 compact tractors. It contains 91 pages listing component part numbers and references for the various engine systems of the different tractor models. The pages are organized by component and sub-component and include items like the cylinder block, heads, manifolds, pumps, nozzles and tanks.
This document provides parts information for the cylinder head, rocker shaft, crankshaft, pistons, and connecting rods of a Massey Ferguson 365 tractor engine. It includes the part numbers, quantities, descriptions, and other details for 33 relevant parts. Footnotes provide additional specification details or replacement part numbers for some items. The document is intended to aid in servicing and repairing these core engine components.
JCB WLS 432ZX Wheeled Loader Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides a summary of a service manual for a WLS 432ZX machine. It includes sections on general information, care and safety, maintenance, and specific components like the body and framework, hydraulics, transmission, and brakes. It specifies that only JCB approved replacement parts should be used. Various service tools are also described that are required for tasks like installing glass, cutting out broken glass, and setting up pivots. Torque settings are provided for common metric bolt sizes. Colour codes are also defined for diagrams depicting hydraulic system pressures and flows.
Massey Ferguson MF155 MF158 TRACTOR Parts Catalogue Manual Instant Download.pdfid9sodkdkmdm
This document provides a parts list and diagrams for the engine and various systems of a Massey Ferguson 155/158 tractor. It includes over 35 individual items related to the engine, electrical equipment, alternator, generator, starter, and other components. Each item lists the part number, quantity, description, and any relevant comments to identify variations or component numbers. The document aims to catalog all relevant parts for servicing and repair of this tractor model.
JCB VM115 TIER Ⅲ VIBROMAX Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides a numerical list of service tools required for procedures in the manual. The list includes tools for sections on body and framework (B), electrics (C), and hydraulics (E). Specific tools are not listed, but are available as kits that can be found in the tool detail reference section. General workshop tools are also expected to be available.
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and related systems, including the cylinder block, crankshaft, cylinder head, rocker arm assembly, and other components. Each part is given an item number, part number, quantity, description, and in some cases additional comments or part number variants. Diagrams illustrate the layout and components of the engine systems.
The document contains technical specifications and diagrams for a Massey Ferguson MF 2620 tractor. It lists over 100 individual parts that make up the engine, cylinder block, rocker arm, cylinder head, crankshaft, and cylinder head cover. The parts are organized numerically and include the part number, quantity, description, and any relevant comments for each component.
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2620 tractor, including the engine, cylinder block, flywheel housing, crankshaft, pistons, connecting rods, and cylinder head. Each component lists the relevant part numbers, quantities, descriptions, and any additional comments. Serial numbers and engine numbers are referenced for certain part applicability.
This document provides a parts list and descriptions for servicing the engine of a Massey Ferguson 275 tractor. It lists 31 individual parts needed for the engine, including the cylinder block, crankshaft, pistons, connecting rods, gears, and other components. Each part is identified by a part number, quantity needed, description, and any relevant comments. The list separates parts for different engine types and model years.
This document contains lists of components for engine repair or replacement. It includes items like cylinders, crankshafts, connecting rods, pistons, gaskets, screws, sensors and other parts. Quantities and references are provided for each component. Applications are for F/XL Tier 2 tractors from 2003-2008.
Massey Ferguson MF 396 C CRAWLER (IT) Parts Catalogue Manual Instant Download...id9sodkdkmdm
This document contains parts lists and assembly details for the engine of a Massey Ferguson MF 396 C Crawler excavator. It includes lists of parts for the engine assembly, cylinder block, crankshaft and connecting rods, cylinder head, and rocker shaft assembly. Quantities, part numbers, and other identifying information are provided for each part.
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 2680 tractor engine. It includes 44 items that make up the cylinder block, 12 items for the flywheel housing, and numerous other parts grouped into sections for the crankshaft, cylinder head, rocker shaft, and other engine systems. Each item lists the part number, quantity, description, and any replacement or additional part information.
JCB VIBROMAX 255 265 TANDEM ROLLER Service Repair Manual Instant Download.pdfid9sodkdkmdm
This service manual provides information on the 255/265 tandem roller including:
1) The machine uses a Kubota diesel engine and hydrostatic drive system to power drums or pneumatic tires for compaction.
2) Safety features and procedures are outlined covering general operation, maintenance, and personal protective equipment.
3) Systems covered include propulsion, vibration, steering, brakes, hydraulics, electrical, and attachments.
JCB Transmissions Service Repair Manual Instant Download.pdfid9sodkdkmdm
This document provides an overview and instructions for using a service manual for JCB transmissions. It includes a scope section describing the modular structure of the manual and applicable axle and gearbox assemblies. Tables list the relevant procedure sections for dismantling, inspecting and assembling components for different JCB machine models. Information is also provided on torque settings, service tools, and sealing compounds to aid in repair work. The document aims to guide users to the appropriate sections for servicing specific transmission components across JCB's product lines.
This document provides part numbers and descriptions for replacement parts for a Massey Ferguson MF 675 tractor from 1984. It includes lists of parts for the engine accessories, guards, fan, cylinder block, crankshaft and connecting rods, cylinder head, flywheel, and front end drive input and output. Each item lists the part number, quantity, description, and any comments about the part.
This document provides information about identifying a JCB TM310 machine, including its components. It discusses the machine identification plate containing serial numbers for the machine and major units. It also describes typical product identification numbers (PIN), vehicle identification numbers (VIN), and identification plates for the engine, transmission, drop box, and axle. Component plates contain serial numbers and information about the type, model, and year of manufacture. The identification and serial numbers can be used to properly identify the specific machine and order correct replacement parts.
This document is the service manual for JCB machines TM180/220. It provides instructions for servicing and repairing these machines. The manual is organized into multiple sections covering general information, safety, maintenance procedures, and technical information on specific components and systems. Technicians are instructed to follow all safety procedures and only perform work on the specific machine models listed in the applications tables at the front of each section. The format and organization of the manual is described to help technicians find the correct information for the maintenance or repair tasks.
McCormick MTX Series (2002-2007) - MTX3 - MTX110, MTX125, MTX140 Parts Catalo...id9sodkdkmdm
This document contains parts listings and diagrams for engine components of McCormick MTX Series tractors from 2002-2007, including the MTX3, MTX110, MTX125 and MTX140 models. It lists over 50 individual part numbers, descriptions and quantities for items such as an engine assembly, radiator, hoses, bolts, seals, brackets and other engine parts. The document provides replacement part information for work on engine systems.
This document contains parts lists and repair instructions for engine components. It lists 54 individual parts for a kit labeled ZZ50312, including blocks, caps, plugs, dowels, and screws. It also provides information on replacement parts, repair times, and part numbers.
This document contains parts lists and repair instructions for engine components. It lists part numbers, descriptions, and repair times for replacing components like pistons, connecting rods, cylinder heads, valves, rocker arms, and more. The parts are for McCormick tractors from model years 2003-2008. Replacement times are provided in hours, and parts are identified as wear items that require replacement during an overhaul.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
5. Section 1 - General Information
1 - 1 1 - 1
9803/9430-01
Introduction
About this Publication
This publication is designed for the benefit of JCB
Distributor Service Engineers who are receiving, or have
received, training by JCB Worldwide Training.
These personnel should have a sound knowledge of
workshop practice, safety procedures, and general
techniques associated with the maintenance and repair of
hydraulic earthmoving equipment.
Renewal of oil seals, gaskets, etc., and any component
showing obvious signs of wear or damage is expected as
a matter of course. It is also expected that components will
be cleaned and lubricated where appropriate, and that any
opened hose or pipe connections will be blanked to
prevent excessive loss of hydraulic fluid and ingress of dirt.
Finally, please remember above all else SAFETY MUST
COME FIRST!
The manual is compiled in sections, the first three are
numbered and contain information as follows:
1 General Information - includes torque settings and
service tools.
2 Care and Safety - includes warnings and cautions
pertinent to aspects of workshop procedures etc.
3 Routine Maintenance - includes service schedules
and recommended lubricants for all the machine.
The remaining sections are alphabetically coded and deal
with Dismantling, Overhaul etc. of specific components, for
example:
Section contents, technical data, circuit descriptions,
operation descriptions etc. are inserted at the beginning of
each alphabetically coded section.
All sections are listed on the front cover; tabbed divider
cards align directly with individual sections on the front
cover for rapid reference.
'Left Hand' and 'Right Hand' are as viewed from the rear of
the machine facing forwards.
This Service Manual covers the following machines:
JCB ZT 20D from SN 1225000 to SN 1225999
A Attachments
B Body and Framework...etc.
6. Section 1 - General Information
Introduction
About this Publication
1 - 2 1 - 2
9803/9430-01
Page left intentionally blank
7. Section 1 - General Information
1 - 3 1 - 3
9803/9430-01
Machine Identification
Identifying Your Machine
Machine Identification Plate
Your machine has an identification plate mounted as
shown. K Fig 1. ( T 1-3) Information contained on this
plate is the Product Identification Number, Type, the
Weight in kg, Year of Manufacture, Engine Power in kw
and the Engine RPM.
Fig 1.
Typical Product Identification Number
(PIN)
A typical Product Identification Number is given below.
1 Machine Model
2 Year of Manufacture
3 Country of Origin
4 Machine Serial Number
V001950
JCB COMPACT PRODUCTS LIMITED
HAREWOOD ESTATE,LEEK ROAD,CHEADLE
STOKE-ON-TRENT,UNITED KINGDOM,ST102JU
Product Identification Number PIN Type
A WEIGHT (kg) YEAR OF MANUFACTURE ENGINE POWER kw ENGINE RPM
JCBZT20D 6 U 1225008
1 2 3 4
8. Section 1 - General Information
Machine Identification
Identifying Your Machine
1 - 4 1 - 4
9803/9430-01
Engine Identification Plate Location
The engine identification plate A is attached to the right
side of the engine block, next to the electric starter. The
information contained on this plate includes the engine
model and serial numbers. K Fig 2. ( T 1-4)
Fig 2.
Roll Over Protection Structure (ROPS)
!MWARNING
Modified and wrongly repaired ROPS, TOPS & FOGS
Structures are dangerous. Do not modify the TOPS
Structure. Do not attempt to repair the ROPS, TOPS &
FOGS Structure. If the ROPS, TOPS & FOGS Structure
has been in an accident, do not use the machine until
the structure has been inspected and repaired. This
must be done by a qualified person. For assistance,
contact your JCB dealer. Failure to take precautions
could result in death or injury to the operator.
5-3-1-7_2
Your machine is built to the ROPS standard and has an
identification label fitted on the ROPS bar. A typical
identification label is shown below. K Fig 3. ( T 1-4)
Fig 3.
Component Identification
Engine Identification
The JCB Zero-Turn Mower is powered by a Yanmar™ 17
HP 2V750 liquid cooled V-Twin Engine.
The data information is located on the right side of the
Yanmar engine, behind the RH hydraulic pump, along side
the right ROPS post, K Fig 2. ( T 1-4).
This data plate decal contains the engine model, the type,
and the engine serial number.
Always refer to this information when ordering parts,
requesting warranty, etc.
Engine information can be obtained through the Yanmar
Europe web-site.
When working on or repairing the Engine, use genuine
engine service parts only. Engine warranty may be
invalidated if “after market” parts are used.
V002060
9. Section 1 - General Information
Machine Identification
Identifying Your Machine
1 - 5 1 - 5
9803/9430-01
Important: All matters concerning service and warranty
for the Yanmar engine is handled by Yanmar. JCB
assumes NO service or warranty responsibility for engine
concerns.
Hydraulic Pump Identification
Hydraulic pump identification is located on a bar code
decal fastened to the side of the pump.
Fig 4.
The model number and the date coded serial numbers are
found on this decal.
Duplicate pump decals are also mounted above the serial
number decal on the mainframe.
Always refer to this information when ordering parts,
requesting warranty, etc.
Wheel Motor Identification
Wheel motor identification is found on a round tag mounted
on the end plate of the motor. The motor type code, model
and serial numbers are engraved into this tag.
Fig 5.
Always refer to this information when ordering parts,
requesting warranty, etc. Hydro-Gear PG (10cc) Series
Hydraulic Pump
10. Section 1 - General Information
1 - 6 1 - 6
9803/9430-01
Service Tools
Numerical List
The tools listed in the table are special tools required for
carrying out the procedures described in this manual.
These tools are available from JCB Service.
Some tools are available as kits or sets, the part numbers
for parts within such kits or sets are not listed here. For full
details of all tools, including the content of kits and sets,
see the relevant section in this manual.
Note: Tools other than those listed will be required. It is
expected that such general tools will be available in any
well equipped workshop or be available locally from any
good tool supplier.
Part
Number
Description Tool Detail Reference
- see Section:
- AVO Test Kit - see tool detail reference for content C
- Electrical Repair Kit - see tool detail reference for content C
993/85700 Battery Tester C
11. Section 1 - General Information
1 - 7 1 - 7
9803/9430-01
Fastener Torque Chart
Numerical List
All SAE fasteners locally purchased for use on the JCB
Mower must be Grade 5 or equivalent, unless otherwise
specified in the parts manual. Use the torque chart for all
Grade 5 fasteners. Special fastener torques are shown
below the chart.
Important: All torque specifications apply to clean and
lightly oiled fasteners, hoses or fittings. Torque
specifications SHOULD NOT be followed when fastening
plastic parts.
Chart - SAE Grade 5 Fasteners
Size Nm lbf ft
Lube Dry Lube Dry
1/4-20 9 12 7 9
5/16-18 20 27 15 20
3/8-16 41 47 30 35
7/16-14 61 75 45 55
1/2-13 81 108 60 80
9/16-12 136 163 100 120
5/8-11 176 231 130 170
3/4-10 298 407 220 300
12. Section 1 - General Information
Fastener Torque Chart
Numerical List
1 - 8 1 - 8
9803/9430-01
Special Torques
Important: DO NOT use the pulley nut to hold the spindle
while tightening the blade as the pulley nut could be over
torqued. This could cause spindle spacer and bearing
damage.
Description Torque
Mowing Blade Bolt - 9/16-12 x 1 3/4 Grade 8 170 Nm (125 lbf ft)
Spindle Pulley Nut - 3/4-16 UNF 109 Nm (80 lbf ft)
Engine Fasteners, M10 39 Nm (29 lbf ft)
Engine Fasteners , M8 20 Nm (15 lbf ft)
ROPS Fasteners - 1/2-13 Bolts & Nuts 109 Nm (80 lbf ft)
Spindle Housing Nuts - 7/16-20 UNF 54 Nm (40 lbf ft)
PTO Clutch Bolt - 7/16-20 x 2 1/4 61 Nm (45 lbf ft)
Steering Dampener Nuts - M8-1.25 33 Nm (24 lbf ft)
Fuel Tank Bolts 3/8-16 8.5 Nm (6 lbf ft)
Wheel Motor End Cover Bolts - 3/8-24 Gr. 8 68 Nm (50 lbf ft)
Hydraulic Pump ByPass Valve 12 Nm (9 lbf ft)
Hydraulic Pump End Cap Bolts 22 Nm (16 lbf ft)
Hydraulic Pump Charge Pump Screws 12 Nm (9 lbf ft)
High Pressure Pump/Motor Hoses/Fittings (MUST be lightly oiled) 82 Nm (60 lbf ft)
13. Section 1 - General Information
Consumables
Sealing and Retaining Compounds
1 - 9 1 - 9
9803/9430-01
Consumables
Sealing and Retaining Compounds
T11-001_3
Table 1.
Type Description Part No. Quantity
JCB Multi-Gasket A medium strength sealant suitable for all sizes of
gasket flanges, and for hydraulic fittings of 25-65 mm
diameter.
4102/1212 50 ml
JCB High Strength Threadlocker A high strength locking fluid for use with threaded
components. Gasketing for all sizes of flange where
the strength of the joint is important.
4102/0551 50 ml
JCB Retainer (High Strength) For all retaining parts which are unlikely to be
dismantled.
4101/0651 50 ml
JCB Threadlocker and Sealer A medium strength locking fluid for sealing and
retaining nuts, bolts, and screws up to 50 mm
diameter, and for hydraulic fittings up to 25 mm
diameter.
4101/0250 10 ml
4101/0251 50 ml
JCB Threadlocker and Sealer
(High Strength)
A high strength locking fluid for sealing and retaining
nuts, bolts, and screws up to 50 mm diameter, and
for hydraulic fittings up to 25 mm diameter.
4101/0550 10 ml
4101/0552 200 ml
JCB Threadseal A medium strength thread sealing compound. 4102/1951 50 ml
JCB Activator A cleaning primer which speeds the curing rate of
anaerobic products.
4104/0251 200 ml (Aerosol)
4104/0253 1 ltr (Bottle)
JCB Cleaner/Degreaser For degreasing components prior to use of
anaerobic adhesives and sealants.
4104/1557 400 ml (Aerosol)
Direct Glazing Kit For one pane of glass; comprises of:
– 1 x Ultra Fast Adhesive (310 ml)
– 1 x Active Wipe 205 (30 ml)
– 1 x Black Primer 206J (30 ml)
– plus applicator nozzle etc.
993/55700
Ultra Fast Adhesive For direct glazing. 4103/2109 310 ml
Active Wipe 205 For direct glazing. 4104/1203 250 ml
Black Primer 206J For direct glazing. 4201/4906 30 ml
Clear Silicone Sealant To seal butt jointed glass. 4102/0901
Plastic to Metal Bonder To seal plastic to metal joints. 4103/0956 50 g
Black Polyurethane Sealant To finish exposed edges of laminated glass. 4102/2309 310 ml
14. Section 1 - General Information
Consumables
Sealing and Retaining Compounds
1 - 10 1 - 10
9803/9430-01
Page left intentionally blank
15. Section 2 - Care and Safety
2 - 0 2 - 0
9803/9430-1
Page left intentionally blank
16. Page No.
Contents
Section 2 - Care and Safety
2 - i 2 - i
Safety Notices
Introduction .............................................................................................. 2 - 1
Safety Checklist ....................................................................................... 2 - 2
Safety Decals ........................................................................................ 2 - 10
18. Section 2 - Care and Safety
2 - 1 2 - 1
9803/9430-01
Safety Notices
Introduction
T1-006
!MWARNING
Study the Operator Manual before starting the
machine. You must understand and follow the
instructions in the Operator Manual. You must
observe all relevant laws and regulations. If you are
unsure about anything, ask your JCB dealer or
employer. Do not guess, you or others could be killed
or seriously injured.
INT-1-1-1_2
In this publication and on the machine, there are safety
notices. Each notice starts with a signal word. The signal
word meanings are given below.
!MDANGER
Denotes an extreme hazard exists. If proper
precautions are not taken, it is highly probable that the
operator (or others) could be killed or seriously
injured.
INT-1-2-1
!MWARNING
Denotes a hazard exists. If proper precautions are not
taken, the operator (or others) could be killed or
seriously injured.
INT-1-2-2
!MCAUTION
Denotes a reminder of safety practices. Failure to
follow these safety practices could result in injury to
the operator (or others) and possible damage to the
machine.
INT-1-2-3
19. Section 2 - Care and Safety
Safety Notices
Safety Checklist
2 - 2 2 - 2
9803/9430-01
Safety Checklist
Safety - Yours and Others
INT-1-3-1_3
All machinary can be hazardous. When a machine is
correctly operated and properly maintained, it is a safe
machine to work with. But when it is carelessly operated or
poorly maintained it can become a danger to you (the
operator) and others.
In this manual and on the machine you will find warning
messages. Read and understand them. They tell you of
potential hazards and how to avoid them. If you do not fully
understand the warning messages, ask your employer or
JCB distributor to explain them.
But safety is not just a matter of responding to the
warnings. All the time you are working on or with the
machine you must be thinking what hazards there might be
and how to avoid them.
Do not work with the machine until you are sure that you
can control it.
Do not start any job until you are sure that you and those
around you will be safe.
If you are unsure of anything, about the machine or the job,
ask someone who knows. Do not assume anything.
Remember
BE CAREFUL
BE ALERT
BE SAFE
General Safety
T1-007
!MWARNING
Operator Manual
You and others can be injured if you operate or
maintain the machine without first studying the
Operator Manual. Read the safety instructions before
operating the machine. If you do not understand
anything, ask your employer or JCB dealer to explain
it. Keep the Operator Manual clean and in good
condition. Do not operate the machine without an
Operator Manual in the cab, or if there is anything on
the machine you do not understand.
INT-1-3-2_2
!MWARNING
Care and Alertness
All the time you are working with or on the machine,
take care and stay alert. Always be careful. Always be
alert for hazards.
INT-1-3-5
!MWARNING
Clothing
You can be injured if you do not wear the proper
clothing. Loose clothing can get caught in the
machinery. Wear protective clothing to suit the job.
Examples of protective clothing are: a hard hat, safety
shoes, safety glasses, a well fitting overall, ear-
protectors and industrial gloves. Keep cuffs fastened.
Do not wear a necktie or scarf. Keep long hair
restrained.
INT-1-3-6
!MWARNING
Alcohol and Drugs
It is extremely dangerous to operate machinery when
under the influence of alcohol or drugs. Do not
consume alcoholic drinks or take drugs before or
while operating the machine or attachments. Be aware
of medicines which can cause drowsiness.
INT-1-3-9_2
!MWARNING
Feeling Unwell
Do not attempt to operate the machine if you are
feeling unwell. By doing so you could be a danger to
yourself and those you work with.
8-1-2-4
!MWARNING
Mobile Phones
Switch off your mobile phone before entering an area
with a potentially explosive atmosphere. Sparks in
such an area could cause an explosion or fire
resulting in death or serious injury.
Switch off and do not use your mobile phone when
refuelling the machine.
INT-3-3-9
20. Section 2 - Care and Safety
Safety Notices
Safety Checklist
2 - 3 2 - 3
9803/9430-01
!MWARNING
Lifting Equipment
You can be injured if you use faulty lifting equipment.
Make sure that lifting equipment is in good condition.
Make sure that lifting tackle complies with all local
regulations and is suitable for the job. Make sure that
lifting equipment is strong enough for the job.
INT-1-3-7
!MWARNING
Raised Equipment
Raised equipment can fall and injure you. Do not walk
or work under raised equipment unless safely
supported.
13-1-1-6
!MWARNING
Raised Machine
NEVER position yourself or any part of your body
under a raised machine which is not properly
supported. If the machine moves unexpectedly you
could become trapped and suffer serious injury or be
killed.
INT-3-3-7_1
!MDANGER
Lightning
Lightning can kill you. Do not use the machine if there
is lightning in your area.
5-1-1-2
!MWARNING
Machine Modifications
This machine is manufactured in compliance with
legislative and other requirements. It should not be
altered in any way which could affect or invalidate any
of these requirements. For advice consult your JCB
Distributor.
INT-1-3-10_2
Operating Safety
!MWARNING
Machine Condition
A defective machine can injure you or others. Do not
operate a machine which is defective or has missing
parts. Make sure the maintenance procedures in this
manual are completed before using the machine.
INT-2-1-2_2
!MWARNING
Machine Limits
Operating the machine beyond its design limits can
damage the machine, it can also be dangerous. Do not
operate the machine outside its limits. Do not try to
upgrade the machine performance with unapproved
modifications.
INT-2-1-4
!MWARNING
Engine/Steering Failure
If the engine or steering fails, stop the machine as
quickly as possible. Do not operate the machine until
the fault has been corrected.
INT-2-1-5
!MWARNING
The engine has exposed rotating parts. Switch OFF the
engine before working in the engine compartment. Do
not use the machine with the engine cover open.
5-2-6-5
!MWARNING
Exhaust Gases
Breathing the machine exhaust gases can harm and
possibly kill you. Do not operate the machine in closed
spaces without making sure there is good ventilation.
If possible, fit an exhaust extension. If you begin to
feel drowsy, stop the machine at once and get into
fresh air.
INT-2-1-10_2
21. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
22. Section 2 - Care and Safety
Safety Notices
Safety Checklist
2 - 4 2 - 4
9803/9430-01
!MWARNING
If the machine is fitted with a Roll Over Protection
Structure (ROPS) and/or a Falling Objects Protection
Structure (FOPS), you could be killed or seriously
injured if you operate the machine with a damaged or
missing ROPS/FOPS. If the ROPS/FOPS has been in
an accident, do not use the machine until the structure
has been renewed. Modifications and repairs that are
not approved by the manufacturer may be dangerous
and will invalidate the ROPS/FOPS certification.
INT-2-1-9_5
!MWARNING
Work Sites
Work sites can be hazardous. Inspect the site before
working on it. Look for potholes, weak ground, hidden
rocks etc. Check for utilities such as electric cables
(overhead and underground), gas and water pipes etc.
Mark the positions of the underground cables and
pipes. Make sure that you have enough clearance
beneath overhead cables and structures.
INT-2-2-1
!MWARNING
Communications
Bad communications can cause accidents. Keep
people around you informed of what you will be doing.
If you will be working with other people, make sure any
hand signals that may be used are understood by
everybody. Work sites can be noisy, do not rely on
spoken commands.
INT-2-2-3
!MWARNING
Parking
An incorrectly parked machine can move without an
operator. Follow the instructions in the Operator
Manual to park the machine correctly.
INT-2-2-4_2
!MWARNING
Banks and Trenches
Banked material and trenches can collapse. Do not
work or drive too close to banks and trenches where
there is danger of collapse.
INT-2-2-5
!MWARNING
Ramps and Trailers
Water, mud, ice, grease and oil on ramps or trailers can
cause serious accidents. Make sure ramps and trailers
are clean before driving onto them. Use extreme
caution when driving onto ramps and trailers.
INT-2-2-6
!MWARNING
Safety Barriers
Unguarded machines in public places can be
dangerous. In public places, or where your visibility is
reduced, place barriers around the work area to keep
people away.
INT-2-2-8
!MDANGER
Sparks
Explosions and fire can be caused by sparks from the
exhaust or the electrical system. Do not use the
machine in closed areas where there is flammable
material, vapour or dust.
INT-2-2-10
!MWARNING
Hazardous Atmospheres
This machine is designed for use in normal out door
atmospheric conditions. It should not be used in an
enclosed area without adequate ventilation. Do not
use the machine in a potentially explosive
atmosphere, i.e. combustible vapours, gas or dust,
without first consulting your JCB Distributor.
INT-2-1-14
!MCAUTION
Regulations
Obey all laws, work site and local regulations which
affect you and your machine.
INT-1-3-3
23. Section 2 - Care and Safety
Safety Notices
Safety Checklist
2 - 5 2 - 5
9803/9430-01
!MWARNING
Practice
You or others can be killed or seriously injured if you
do unfamiliar operations without first practising them.
Practise away from the work site on a clear area. Keep
other people away. Do not perform new operations
until you are sure you can do them safely.
INT-2-1-1
!MWARNING
Reversing
Reversing at high speeds can cause accidents. Do not
reverse in a high gear with full throttle. Always drive at
a safe speed to suit working conditions.
INT-2-2-9_1
!MWARNING
Airborne particles of light combustible material such
as straw, grass, wood shavings, etc. must not be
allowed to accumulate within the engine compartment
or in the driveshaft guards (when fitted). Inspect these
areas frequently and clean at the beginning of each
work shift or more often if required. Before opening
the engine cover, ensure that the top is clear of debris.
5-3-1-12_3
!MWARNING
Keep the machine controls clean and dry. Your hands
and feet could slide off slippery controls. If that
happens you could lose control of the machine.
2-2-3-6
!MWARNING
Visibility
Accidents can be caused by working in poor visibility.
Use your lights to improve visibility. Keep the road
lights, windows and mirrors clean.
Do not operate the machine if you cannot see clearly.
5-1-4-7
!MWARNING
Electrical Power Cables
You could be electrocuted or badly burned if you get
the machine or its attachments too close to electrical
power cables.
You are strongly advised to make sure that the safety
arrangements on site comply with the local laws and
regulations concerning work near electric power lines.
Before you start using the machine, check with your
electricity supplier if there are any buried power
cables on the site.
There is a minimum clearance required for working
beneath overhead power cables. You must obtain
details from your local electricity supplier.
2-2-5-4
!MCAUTION
If you have an attachment which is not covered in the
Operator Manual do not install it, use it or remove it
until you have obtained, read and understood the
pertinent information. Install attachments only on the
machines for which they were designed.
5-5-1-1_2
!MWARNING
Use only the JCB approved attachments that are
specified for your machine. Operating with non-
specified attachments can overload the machine,
causing possible damage and machine instability
which could result in injury to yourself or others.
The use of non-approved attachments could invalidate
your warranty.
2-4-5-2_1
!MWARNING
Controls
You or others can be killed or seriously injured if you
operate the control levers from outside the cab.
Operate the control levers only when you are correctly
seated inside the cab.
INT-2-1-3