This document is a service manual for an excavator model JCB305, JS305. It contains instructions for servicing and repairing components of the excavator including the engine, fuel system, cooling system, driveline, hydraulics, and electrical system. The foreword stresses the importance of understanding the operator's manual before operating the machine and warns not to operate it without first studying the manual.
Jcb 9 tft dumper service repair manual sn from hrm1382 to hrm4003fusefjskekkmem
This service manual provides instructions for servicing the braking system of dumpers. It contains information on health and safety when working on the brakes, technical specifications, component identification, troubleshooting, and bleeding the brakes. The braking system uses mineral oil and contains separate front and rear brake circuits for safety. Adjustment is generally not needed as the brakes are self-adjusting, but bleeding may be required if the brake lines leak fluid.
Jcb 3 cx backhoe loader service repair manual sn from 2509500 and upfdjjsekksemxs
This service manual provides instructions for servicing backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The document provides detailed procedures, diagrams, and specifications for maintenance, repair, and removal/installation of parts. Safety warnings are included throughout advising technicians to read and understand instructions before working on the machine.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
This service manual provides information for servicing Fastrac agricultural tractors models 8290 and 8330. It contains sections covering the machine, attachments, body, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, steering, driveline, suspension, hydraulics, and electrical systems. The engine section includes subsections on pistons, piston rings, rocker arms, and other components. It provides identification diagrams, specifications, operation descriptions, and maintenance/inspection procedures.
Jcb 210 x excavator service repair manual (sn from 2500051 and up)udjfjjskekkem
This service manual provides instructions for servicing an excavator model 210X and 220X. It contains sections on the machine components, attachments, body, operator station, HVAC, engine, fuel and exhaust systems, cooling system, driveline, hydraulic system, electrical system, fasteners, consumable products, and after sales support. The section on the engine crankcase provides details on removing and installing the crankcase, including technical specifications. Proper torque values and sequences must be followed to correctly remove and install the crankcase.
Liebherr r964 c 1278 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Jcb 9 tft dumper service repair manual sn from hrm1382 to hrm4003fusefjskekkmem
This service manual provides instructions for servicing the braking system of dumpers. It contains information on health and safety when working on the brakes, technical specifications, component identification, troubleshooting, and bleeding the brakes. The braking system uses mineral oil and contains separate front and rear brake circuits for safety. Adjustment is generally not needed as the brakes are self-adjusting, but bleeding may be required if the brake lines leak fluid.
Jcb 3 cx backhoe loader service repair manual sn from 2509500 and upfdjjsekksemxs
This service manual provides instructions for servicing backhoe loaders models 3CX, 4CX, and 5CX. It contains sections covering the entire machine including the engine, fuel system, cooling system, brakes, steering, hydraulics, electrical system, and other components. The document provides detailed procedures, diagrams, and specifications for maintenance, repair, and removal/installation of parts. Safety warnings are included throughout advising technicians to read and understand instructions before working on the machine.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
This service manual provides information for servicing Fastrac agricultural tractors models 8290 and 8330. It contains sections covering the machine, attachments, body, operator station, HVAC, engine, fuel/exhaust, cooling, brakes, steering, driveline, suspension, hydraulics, and electrical systems. The engine section includes subsections on pistons, piston rings, rocker arms, and other components. It provides identification diagrams, specifications, operation descriptions, and maintenance/inspection procedures.
Jcb 210 x excavator service repair manual (sn from 2500051 and up)udjfjjskekkem
This service manual provides instructions for servicing an excavator model 210X and 220X. It contains sections on the machine components, attachments, body, operator station, HVAC, engine, fuel and exhaust systems, cooling system, driveline, hydraulic system, electrical system, fasteners, consumable products, and after sales support. The section on the engine crankcase provides details on removing and installing the crankcase, including technical specifications. Proper torque values and sequences must be followed to correctly remove and install the crankcase.
Liebherr r964 c 1278 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 1145 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 1126 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r960 demolition 1466 hydraulic excavator service repair manualufjdjfjksekkmm
This document is a service manual that covers maintenance and repair for various systems of an industrial machine. It includes sections on technical data, maintenance procedures, drive systems, cooling systems, hydraulics, electrical systems, gearboxes, and other components. The manual provides instructions and specifications to service the machine.
Liebherr r944 c hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for maintenance and repairs.
2. Sections covering the engine, hydraulic and electrical systems, swing gear, track components and other parts.
3. Safety symbols and instructions for working on the machines.
The manual is intended to assist customer support but does not replace technical training. It includes schematics, diagrams and detailed views of machine units.
Liebherr r916 1301 classic hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual for Liebherr hydraulic excavators. It contains 18 sections that provide technical data, maintenance guidelines, and instructions for repairing and servicing various components of the excavators, including the engine, hydraulic system, electrical system, and other parts. The manual is intended to assist customer support services and includes safety symbols and instructions for working on the machines. It also provides information on the structure and page numbering system used in the manual.
Liebherr lh80 m hydraulic excavator service repair manualufjdjfjksekkmm
The document discusses safety warnings and signs related to operating machinery. It outlines various hazard symbols and their meanings, and emphasizes the importance of understanding and following all safety instructions. Additional rules and guidelines for designated uses are specified, such as only using attachments that are approved by the manufacturer and not operating in explosive environments. Various warning signs on the machinery are also described.
Liebherr lh80 c hydraulic excavator service repair manualufjdjfjksekkmm
The document discusses safety warnings and signs related to operating machinery. It outlines various hazard symbols and their meanings, and emphasizes the importance of understanding and following all safety instructions. Additional rules and guidelines for designated uses are also covered, such as only using attachments that are approved by the manufacturer and not operating in explosive or contaminated environments. Various warning signs displayed on the machines are illustrated and explained.
Liebherr lh60 m hydraulic excavator service repair manualufjdjfjksekkmm
This document provides safety warnings and instructions for operating a hydraulic excavator. It outlines hazards associated with the machine and stresses the importance of following safety precautions to prevent injury. Specific dangers are indicated by warning signs on the machine. The document also defines the designated use of the excavator as loosening, picking up, transporting, and dumping materials while following technical safety guidelines. Any other uses are considered not in accordance with safe operation of the machine.
Liebherr lh40 m 1215 (tier4f) hydraulic excavator service repair manualufjdjfjksekkmm
This document contains figures and tables describing components of mechanical devices like differentials, shock absorbers, and hydraulic cylinders. It identifies parts that are susceptible to corrosion and recommends corrosion inhibitors and paint coatings from Liebherr to protect these parts. The document encourages downloading a complete manual for more details.
Liebherr lh35 t 1220 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr lh30 1200 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr lh26 1199 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr er 912 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical data, maintenance guidelines, and information on systems for hydraulic excavators models ER 900-942. It covers general information, tools, the engine, coupling and splitterbox, hydraulic system, hydraulic components, electrical system, swing gear, swing ring, travel gear, track components, undercarriage and uppercarriage attachments, cab heater and air conditioning. The manual is intended to assist with maintenance and repairs for the excavator models.
Jcb tm320 telescopic wheel loader service repair manual sn from 2508700 to 25...ufjdjfjksekkmm
This service manual provides instructions for disassembling and assembling the master clutch on a loader. Key steps include using jacking bolts and lifting eyes to remove the clutch cover and drum assembly. Locking plates are installed to secure the clutch assembly while removing attaching bolts. Special retainers hold the clutch plates together as a carrier removes them from the housing. Detailed part identification and replacement of O-rings and seals is specified. Torque values are provided for reassembly.
Jcb jcb305, js305 excavator service repair manual (from 2452101 to 2452200)ufjdjfjksekkmm
This document is a service manual for an excavator model JCB305, JS305. It contains instructions for servicing and repairing components of the excavator including the engine, fuel system, cooling system, driveline, hydraulics, and electrical system. The foreword stresses the importance of understanding the operator's manual before operating the machine and warns not to operate it without first studying the manual.
Jcb 1253, 1202, 1553, 1554 liftall service repair manual from 1900650 to 1902499ufjdjfjksekkmm
The document is a service manual for JCB Liftall 1253/1202/1553/1554 machines. It contains sections covering general information such as machine identification, load charts, torque specifications, and service tools. It also includes sections specific to the body and framework, electrics, hydraulics, engine, and other systems of the machines. The manual provides information and specifications needed to service and repair the Liftall models.
Jcb 1253, 1202, 1553, 1554 liftall service repair manual from 1900500 to 1900648ufjdjfjksekkmm
The document is a service manual that provides information for servicing Liftall 1253/1202/1553/1554 machines. It contains sections covering general information, machine identification, load charts, torque specifications, service tools, and maintenance/repair sections for the body and framework, electrics, hydraulics, engine, and other systems. Technical illustrations and specifications are provided to support repair and maintenance.
Jcb 535 v125 telescopic handler service repair manual sn from 2460601 onwardsufjdjfjksekkmm
This service manual provides instructions for servicing the Loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear.
Caterpillar cat th414 c telehandler operator and maintenance manualufjdjfjksekkmm
This document provides an operation and maintenance manual for several models of JLG telehandlers. It contains important safety information and instructions for pre-operation inspection, operation of controls and indicators, and general safety practices. The manual should be kept with the machine at all times. Operators must be trained and qualified, and follow all safety procedures and instructions contained within the manual. Modifications to the machine must be approved by the manufacturer.
Caterpillar cat th407 c telehandler service repair manualufjdjfjksekkmm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Liebherr r964 c 1145 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r964 c 1126 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r960 demolition 1466 hydraulic excavator service repair manualufjdjfjksekkmm
This document is a service manual that covers maintenance and repair for various systems of an industrial machine. It includes sections on technical data, maintenance procedures, drive systems, cooling systems, hydraulics, electrical systems, gearboxes, and other components. The manual provides instructions and specifications to service the machine.
Liebherr r944 c hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for maintenance and repairs.
2. Sections covering the engine, hydraulic and electrical systems, swing gear, track components and other parts.
3. Safety symbols and instructions for working on the machines.
The manual is intended to assist customer support but does not replace technical training. It includes schematics, diagrams and detailed views of machine units.
Liebherr r916 1301 classic hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual for Liebherr hydraulic excavators. It contains 18 sections that provide technical data, maintenance guidelines, and instructions for repairing and servicing various components of the excavators, including the engine, hydraulic system, electrical system, and other parts. The manual is intended to assist customer support services and includes safety symbols and instructions for working on the machines. It also provides information on the structure and page numbering system used in the manual.
Liebherr lh80 m hydraulic excavator service repair manualufjdjfjksekkmm
The document discusses safety warnings and signs related to operating machinery. It outlines various hazard symbols and their meanings, and emphasizes the importance of understanding and following all safety instructions. Additional rules and guidelines for designated uses are specified, such as only using attachments that are approved by the manufacturer and not operating in explosive environments. Various warning signs on the machinery are also described.
Liebherr lh80 c hydraulic excavator service repair manualufjdjfjksekkmm
The document discusses safety warnings and signs related to operating machinery. It outlines various hazard symbols and their meanings, and emphasizes the importance of understanding and following all safety instructions. Additional rules and guidelines for designated uses are also covered, such as only using attachments that are approved by the manufacturer and not operating in explosive or contaminated environments. Various warning signs displayed on the machines are illustrated and explained.
Liebherr lh60 m hydraulic excavator service repair manualufjdjfjksekkmm
This document provides safety warnings and instructions for operating a hydraulic excavator. It outlines hazards associated with the machine and stresses the importance of following safety precautions to prevent injury. Specific dangers are indicated by warning signs on the machine. The document also defines the designated use of the excavator as loosening, picking up, transporting, and dumping materials while following technical safety guidelines. Any other uses are considered not in accordance with safe operation of the machine.
Liebherr lh40 m 1215 (tier4f) hydraulic excavator service repair manualufjdjfjksekkmm
This document contains figures and tables describing components of mechanical devices like differentials, shock absorbers, and hydraulic cylinders. It identifies parts that are susceptible to corrosion and recommends corrosion inhibitors and paint coatings from Liebherr to protect these parts. The document encourages downloading a complete manual for more details.
Liebherr lh35 t 1220 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr lh30 1200 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr lh26 1199 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a technical manual that was printed on December 25, 2019 at 21:58. It contains instructions and diagrams for mounting different clamping nuts, adjusting swing brakes, and identifying components of hydraulic cylinders and shock absorbers that are at risk for corrosion. It also includes tables listing recommended corrosion inhibitors and paints from Liebherr for protecting hydraulic cylinder components from corrosion.
Liebherr er 912 hydraulic excavator service repair manualufjdjfjksekkmm
The document is a service manual that provides technical data, maintenance guidelines, and information on systems for hydraulic excavators models ER 900-942. It covers general information, tools, the engine, coupling and splitterbox, hydraulic system, hydraulic components, electrical system, swing gear, swing ring, travel gear, track components, undercarriage and uppercarriage attachments, cab heater and air conditioning. The manual is intended to assist with maintenance and repairs for the excavator models.
Jcb tm320 telescopic wheel loader service repair manual sn from 2508700 to 25...ufjdjfjksekkmm
This service manual provides instructions for disassembling and assembling the master clutch on a loader. Key steps include using jacking bolts and lifting eyes to remove the clutch cover and drum assembly. Locking plates are installed to secure the clutch assembly while removing attaching bolts. Special retainers hold the clutch plates together as a carrier removes them from the housing. Detailed part identification and replacement of O-rings and seals is specified. Torque values are provided for reassembly.
Jcb jcb305, js305 excavator service repair manual (from 2452101 to 2452200)ufjdjfjksekkmm
This document is a service manual for an excavator model JCB305, JS305. It contains instructions for servicing and repairing components of the excavator including the engine, fuel system, cooling system, driveline, hydraulics, and electrical system. The foreword stresses the importance of understanding the operator's manual before operating the machine and warns not to operate it without first studying the manual.
Jcb 1253, 1202, 1553, 1554 liftall service repair manual from 1900650 to 1902499ufjdjfjksekkmm
The document is a service manual for JCB Liftall 1253/1202/1553/1554 machines. It contains sections covering general information such as machine identification, load charts, torque specifications, and service tools. It also includes sections specific to the body and framework, electrics, hydraulics, engine, and other systems of the machines. The manual provides information and specifications needed to service and repair the Liftall models.
Jcb 1253, 1202, 1553, 1554 liftall service repair manual from 1900500 to 1900648ufjdjfjksekkmm
The document is a service manual that provides information for servicing Liftall 1253/1202/1553/1554 machines. It contains sections covering general information, machine identification, load charts, torque specifications, service tools, and maintenance/repair sections for the body and framework, electrics, hydraulics, engine, and other systems. Technical illustrations and specifications are provided to support repair and maintenance.
Jcb 535 v125 telescopic handler service repair manual sn from 2460601 onwardsufjdjfjksekkmm
This service manual provides instructions for servicing the Loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear.
Caterpillar cat th414 c telehandler operator and maintenance manualufjdjfjksekkmm
This document provides an operation and maintenance manual for several models of JLG telehandlers. It contains important safety information and instructions for pre-operation inspection, operation of controls and indicators, and general safety practices. The manual should be kept with the machine at all times. Operators must be trained and qualified, and follow all safety procedures and instructions contained within the manual. Modifications to the machine must be approved by the manufacturer.
Caterpillar cat th407 c telehandler service repair manualufjdjfjksekkmm
This document is a service manual that provides information for maintaining and repairing various models of telehandlers. It contains sections covering safety practices, general machine information and specifications, maintenance of the boom assembly, cab and covers, axles/drive shafts/wheels, engine/powertrain systems, hydraulic systems, and electrical systems. The manual provides component terminology, specifications, maintenance schedules, repair and replacement procedures, and troubleshooting information.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. 15 - Engine
33 - Connecting Rod
06 - Big-End Bearing
15 - 128 9813/6700-1 15 - 128
Check (Condition)
1. Check the bearing shell surfaces for signs of
damage and excessive wear.
2. Measure the crank pin diameters to confirm they
are within service limits, refer to Technical Data
(PIL 15-33).
3. Renew any parts that are worn or not within the
specified tolerances.
Remove and Install
Special Tools
Tool
Category
Description Part No. Qty.
Special
Tool
Torque
Wrench
(10-100Nm)
993/70111 1
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Disconnect and remove the fuel pipes from the
injectors, refer to (PIL 18-96).
5. Remove the rocker cover, refer to (PIL 15-42).
6. Remove the fuel injectors, refer to (PIL 18-18).
7. Drain the oil from the engine, refer to (PIL 15-21).
8. Remove the oil sump, refer to (PIL 15-45).
9. Position the engine upside down in a suitable jig
or fixture, supported at the front of the crankcase.
The connecting rod and the big-end bearing cap
have been fracture split and must be kept together
as a set. Care must be taken to avoid contamination
and or damage to the fracture split surfaces.
Remove
1. It is recommended that the big-end bearing caps
are removed in pairs, cylinders 1 and 4 and
cylinders 2 and 3. Rotate the crankshaft so that
the big-end bearing caps on cylinders 2 and 3 are
positioned as shown.
2. Remove the bolts and lift off the big-end bearing
caps from the connecting rods. The bolts must
not be re-used, discard the bolts.
3. 15 - Engine
33 - Connecting Rod
06 - Big-End Bearing
15 - 129 9813/6700-1 15 - 129
Figure 148.
X
1 2
1 Big-end bearing caps
2 Big-end bearing cap bolts
X Cast notch
3. Lift out the bearing shells from the bearing caps.
Carefully rotate the crank to disengage from the
connecting rods and get access to the upper
bearing shells. Lift out the upper bearing shells.
It is recommended that the bearing shells are
renewed. If they are to be reused, label the
bearing shells to make sure that they are installed
in their original positions on assembly.
Figure 149.
4
3
7
Z
1
2
6
5
1 Big-end bearing cap
2 Bolts
3 Connecting rod
4 Piston
5 Piston rings
6 Lower bearing shell
7 Upper bearing shell
Z Fracture split surfaces
4. Carefully rotate the crankshaft to position the big-
end bearing caps of cylinders 1 and 4. Make
sure that the crank does not foul the connecting
rods of cylinders 2 and 3. Remove the bearing
caps and bearing shells as described in previous
steps.
5. Inspect the big-end bearings for signs of damage
and excessive wear, refer to Check Condition
(PIL 15-12).
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
4. 15 - Engine
33 - Connecting Rod
06 - Big-End Bearing
15 - 130 9813/6700-1 15 - 130
3. Install the upper bearing shell to the connecting
rod. Lubricate the bearing shell with clean engine
oil.
4. Install the lower bearing shell to the big-end
bearing cap. Lubricate the bearing shell with
clean engine oil. Install the big-end bearing cap
to the connecting rod. Make sure that the cast
notch on the bearing cap faces to the front of the
engine. Use compressed air to clean the fracture
surfaces before assembly.
5. Install new fixing bolts. Tighten the new bolts in
three stages to the correct torque value.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
Figure 150.
T3
T3 Angle gauge (obtain locally)
6. The bolts are tightened using a torque and angle
method, refer to Fasteners and Fixings, General,
Introduction (PIL 72-00).
Figure 151.
0° +90°
Y
After Installation
1. Carry out the procedures listed, Before Removal
in reverse order.
Table 65.
Item Torque Value
2 - 1st Stage 35N·m
2 - 2nd Stage 65N·m
2 - Final Stage 90°
5. 15 - Engine
36 - Piston
00 - General
15 - 134 9813/6700-1 15 - 134
Technical Data
Table 66.
Engine 444 - SE Engine 444 - excluding SE en-
gine
448, 672
Gudgeon pin bore diame-
ter
- min. 4.0008mm 40.01mm 42.008mm
- max. 40.013mm 40.015mm 42.013mm
Piston ring clearance
- Top ring Half keystone ring Full keystone ring Full keystone ring
- Middle ring 0.11–0.07mm 0.125–0.08mm 0.125–0.08mm
- Bottom (oil) ring 0.09–0.05mm 0.09–0.05mm 0.09–0.05mm
Piston ring gap
- Top ring 0.3–0.5mm 0.3–0.4mm 0.3–0.4mm
- Middle ring 0.55–0.8mm 0.55–0.8mm 0.55–0.8mm
- Bottom (oil) ring 0.25–0.5mm 0.25–0.5mm 0.25–0.5mm
Piston height above
crankcase (cold)
0.0375–0.3385mm 0.00025–0.36825mm
(1)
0.00025–0.36825mm
(1)
Piston groove width
- Top ring 3.108–3.133mm 3.114–3.134mm 3.114–3.134mm
- Middle ring 2.56–2.58mm 2.575–2.595mm 2.575–2.595mm
- Bottom (oil) ring 4.04–4.06mm 4.04–4.06mm 4.04–4.06mm
Piston skirt - 102.853–102.871mm 105.851–105.869mm
Piston pin - 39.994–40mm 41.994–42mm
(1) Nominal measurement is 0.03325mm
6. 15 - Engine
36 - Piston
00 - General
15 - 135 9813/6700-1 15 - 135
Component Identification
Figure 152.
1
2
0
°
1
2
0
°
120°
Y
X
C
TOP
2
A
3
B
4
4a
TOP
TOP
1
7
6
7
5
1 Piston 2 Piston ring - compression No.1
3 Piston ring - compression No.2 4 Piston ring - oil control ring
4a Spiral wire - oil control ring 5 Connecting rod
6 Piston pin 7 Retaining circlip (x2)
X Connecting rod - longest side Y Cast boss - piston
7. 15 - Engine
36 - Piston
00 - General
15 - 136 9813/6700-1 15 - 136
Operation
The groove around the diameter of the upper main
bearing shells allows oil transfer to an oil jet located
in the crankcase bearing saddle. Jets are installed at
the main bearing positions.
The jets spray oil directly to the under side of the
pistons effectively transferring heat away from the
top of the pistons. Oil spray also enters the small end
bearing bushes via a feed hole on the top of each
connecting rod.
Note: On turbocharged engines additional J-jets are
installed. Oilways connect the J-shaped jets fixed to
the crankcase at the underside of each cylinder bore.
Figure 153.
2
6
1 1
2
4
5
3
1 Groove 2 Oil jet
3 Pistons 4 Bearing bushes
5 Crankshaft 6 J shaped jets
8. 15 - Engine
36 - Piston
00 - General
15 - 137 9813/6700-1 15 - 137
Check (Condition)
1. Check the piston for signs of damage and
excessive wear. Measure the piston skirt
diameter, piston pin bore and the clearance in
the piston ring grooves to confirm they are within
service limits. Refer to Piston, Technical Data
(PIL 15-36).
2. Check the piston pin for signs of damage and
excessive wear. Measure the pin diameter to
confirm it is within service limits. Refer to Piston,
Technical Data (PIL 15-36).
The connecting rod small end bearing bush is not
renewable. If the small end bearing bush is damaged
or worn the connecting rod must be renewed as a
complete assembly.
Calibrate
Piston Height Measurement Above
Cylinder Block- DTI Method
Refer to engine, piston, technical data, (PIL
15-36-00).
In the event of sufficient liquid entering the engine, a
hydraulic lock can occur. This may result in bending
of one or more of the connecting rods. Bending of the
connecting rod(s) can occur even when the engine is
cranked by the starter motor.
Bending of the connecting rod may be very slight and
can be checked by carrying out this procedure prior
to a full strip down:
1. With the cylinder head removed, make sure the
surface of the engine block and piston are clean.
2. Zero a DTI (Dial Test Indicator) on the top face
of the cylinder block adjacent to the area on the
piston to be measured. The aim of the procedure
is to use the DTI to take a measurement across 2
locations on the piston that are on the axis of the
gudgeon pin. This will be towards the front and
rear of the engine.
3. Rotate the engine and bring the piston up until
it is 3mm below the engine block face. Carefully
reposition the zeroed DTI above the area of the
piston to be measured.
4. Rotate the engine to bring the piston up to
exactly TDC (Top Dead Centre) and record the
measurement at position 1.
5. Repeat steps 2 to 4 for position 2.
6. Calculate the average of the 2 readings to give
a figure of the piston height above the cylinder
block.
7. Compare the reading obtained to the technical
data.
7.1. If the reading obtained is lower than zero,
the connecting rod may be bent.
7.2. If the reading obtained is equal to the range
stated in technical data, the connecting rod
is not bent.
8. Repeat steps 2 to 7 to check all connecting rods/
pistons.
9. If any connecting rods are bent, strip the engine
and check for further damage.
10. If the engine is serviceable, any connecting rod
that is bent must be replaced.
9. 15 - Engine
36 - Piston
00 - General
15 - 138 9813/6700-1 15 - 138
Figure 154. DTI Measurement
D
C
A
B
A Gudgeon pin axis
B Line of measurement above gudgeon pin axis
C Piston measurement point 1
D Piston measurement point 2
Piston Height Measurement Above
Cylinder Block- Straight Edge Method
Refer to engine, piston, technical data, (PIL
15-36-00).
If a DTI is not available, a calibrated straight
edge may be used to take a measurement. The
measurement will be less accurate.
1. With the cylinder head removed, make sure the
surface of the engine block and piston are clean.
2. Rotate the engine until the piston to be measured
is at TDC.
3. Position the straight edge on top of the piston
along the axis of the gudgeon pin.
4. Use feeler gauges to measure the gap between
the cylinder block face and underside of the
straight edge on both sides, position 1 and
position 2.
5. Calculate the average of the 2 readings to give
a figure of the piston height above the cylinder
block.
5.1. If the reading obtained is lower than zero,
the connecting rod may be bent.
5.2. If the reading obtained is equal to the range
stated in technical data, the connecting rod
is not bent.
6. Repeat steps 1 to 5.2 to check all connecting
rods/pistons.
Figure 155. Straight Edge Measurement
E
F
G
H
J
K
L
E Straight edge
F Measurement position 1
G Measurement position 2
H Cylinder block- top face
J Gudgeon pin axis
K Piston
L Connecting rod
10. 15 - Engine
36 - Piston
00 - General
15 - 139 9813/6700-1 15 - 139
Remove and Install
Before Removal
The following procedure is for one piston and
connecting rod assembly. Note that each assembly
must be replaced in the same cylinder bore. Label
each piston and connecting rod assembly to make
sure it is installed in the correct position on assembly.
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Disconnect and remove the fuel pipes from the
injectors, refer to (PIL 18-96).
5. Remove the rocker cover, refer to (PIL 15-42).
6. Remove the fuel injectors, refer to (PIL 18-18).
7. Remove the cylinder head assembly, refer to (PIL
15-06).
8. Remove the oil sump, refer to (PIL 15-45).
9. Remove the big end bearing caps, refer to (PIL
15-12).
11. 15 - Engine
36 - Piston
00 - General
15 - 140 9813/6700-1 15 - 140
Figure 156.
X
2
1
3
1 Piston 2 Piston ring
3 Connecting rod X Longest side of connecting rod
12. 15 - Engine
36 - Piston
00 - General
15 - 141 9813/6700-1 15 - 141
Remove
The piston and connecting rod assemblies are
removed through the top of the crankcase.
1. Use a suitable scraper and wire wool to clean off
the carbon deposits from around the top of the
cylinder bore. Take care not to scratch or damage
the cylinder bore.
2. Use a hammer and a short length of wood to
tap the piston from the connecting rod side. Take
care not to scratch or damage the cylinder bore
or the connecting rod bearing surface.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. If the upper big end bearing shell has been
removed replace it, refer to (PIL 15-12).
4. Lubricate the cylinder bore with clean engine oil.
5. Use a suitable compressor tool to compress the
piston rings.
6. Insert the piston and connecting rod assembly
into the cylinder bore, make sure that the longest
side of the connecting rod is on the exhaust side
of the crankcase. Take care not to damage the
cooling jets when you guide the connecting rod
down the cylinder bore and over the crank pin
diameter.
After Installation
1. Install the big end bearing caps, refer to (PIL
15-12).
2. Carry out the procedures listed under Before
removal in reverse order.
13. 15 - Engine
36 - Piston
00 - General
15 - 142 9813/6700-1 15 - 142
Disassemble and Assemble
Dismantle
1. Clamp the connecting rod in a vice. Take care not
to damage the connecting rod.
2. It is recommended that the piston rings are
renewed. If they are to be reused, label the
rings to ensure they are installed in the correct
positions and the correct way up on assembly.
Carefully remove the piston rings from the piston.
To avoid damage or distortion to the rings, use a
suitable piston ring expander tool. Note that the
oil control ring is installed with a spiral wire. Pull
the wire apart and remove it.
3. Remove the circlips and push out the piston pin.
4. Use a suitable cleaning agent, clean the carbon
deposits from the piston.
14. 15 - Engine
36 - Piston
00 - General
15 - 143 9813/6700-1 15 - 143
Figure 157.
1
2
0
°
1
2
0
°
120°
Y
X
C
TOP
2
A
3
B
4
4a
TOP
TOP
1
7
6
7
5
1 Piston 2 Piston ring - compression No.1
3 Piston ring - compression No.2 4 Piston ring - oil control ring
4a Spiral wire - oil control ring 5 Connecting rod
6 Piston pin 7 Retaining circlip (x2)
X Connecting rod - longest side Y Cast boss - piston
Inspect
1. Inspect the pistons for signs of wear or damage.
Refer to Check (Condition) (PIL 15-36-00).
15. 15 - Engine
36 - Piston
00 - General
15 - 144 9813/6700-1 15 - 144
Assemble
1. The assembly procedure is the opposite of
the disassemble procedure. Additionally do the
following steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Lubricate the piston pin with clean engine oil.
Assemble the connecting rod to the piston and
insert the piston pin. Make sure that the long side
of the connecting rod is on the same side as the
internal cast boss in the piston.
4. Install new circlips. Make sure that they are
installed correctly in the groove in the piston.
5. Lubricate the piston with clean engine oil. Install
the piston rings to the piston in sequence as
follows:
5.1. Install the spiral wire for the oil control ring
in the bottom groove and locate the locking
wire inside both ends of the spiral as shown.
Using a piston ring expander tool to install
the oil control ring in the bottom groove and
locate the locking wire inside both ends of
the spiral as shown. Ensure that the ring
gap is positioned 180° to the locking wire.
Note: The correct ring orientation can also
be determined from the profile shape of the
ring as shown at C.
5.2. Install the No.2 compression ring into
the middle groove. Note that new rings
have a reference number etched on one
face. Make sure that this face is installed
uppermost in the piston groove. Note:
The correct ring orientation can also be
determined from the profile shape of the
ring as shown at B.
5.3. Install the No.1 compression ring into the
top groove. Note that new rings have a
reference number etched on one face.
Make sure that this face is installed
uppermost in the piston groove. Note:
The correct ring orientation can also be
determined from the profile shape of the
ring as shown at A.
6. Rotate the piston rings so that the ring gaps are
120° apart as shown.
16. 15 - Engine
36 - Piston
03 - Piston Ring
15 - 145 9813/6700-1 15 - 145
03 - Piston Ring
Introduction
Gas sealing inside the piston is achieved by the use
of piston rings. The rings are loosely installed into
grooves in the piston. The rings are split at a point in
the rim, to allow them to press against the cylinder
with a light spring pressure.
Two types of ring are used:
- Upper rings have solid faces and provide gas
sealing
- Lower rings have narrow edges and have a U-
shaped profile, to act as oil scrapers.
17. 15 - Engine
42 - Rocker and Fittings
00 - General
15 - 150 9813/6700-1 15 - 150
Technical Data
Table 67. Rocker Levers, Rocker Shafts and Tappets Data
Valve clearances measured at the valve bridge piece
tip of the rockers (measured cold):
- Inlet 0.19–0.27mm
- Exhaust 0.56–0.64mm
Rocker clearances measured at the adjusting screw
tip of the rockers (measured cold):
- Inlet 0.15–0.2mm
- Exhaust 0.43–0.5mm
Rocker lever bore diameter
- min 26.058mm
- max 26.092mm
Rocker shaft diameter
- min 26.003mm
- max 26.021mm
Tappets stem diameter
- min 19.975mm
- max 19.985mm
Tappet bore diameter
- min 20mm
- max 20.021mm
Tappet height (maximum) 55.25mm
19. 15 - Engine
42 - Rocker and Fittings
00 - General
15 - 152 9813/6700-1 15 - 152
Operation
When the camshaft lobe raises the outside of the
rocker arm, the inside presses down on the valve
stem to open the valve. When the outside of the
rocker arm is permitted to return due to the camshafts
rotation, the inside rises to allow the valve spring to
close the valve.
Figure 159.
1 Oil feed from main gallery 2 Small transfer gallery
3 Shaft pedestal 4 Rocker shaft fixing bolt hole
5 Centre rocker shaft drilling 6 Cross drillings
7 Rocker pivot bushes 8 Cross drilling
9 Groove
Lubrication
Oil is fed from the main gallery via a drilling which
passes up through the crankcase and the cylinder
head to a small transfer gallery under the rocker
shaft pedestal. The oversize rocker shaft fixing bolt
hole allows oil to pass into a drilling in the centre of
the rocker shaft. Further cross drillings transfer oil
to each of the rocker pivot bushes. A cross drilling
in each rocker transfers oil to the top of the rocker
where it flows by gravity along a groove to the rocker
tip.
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. 15 - Engine
42 - Rocker and Fittings
00 - General
15 - 153 9813/6700-1 15 - 153
Check (Condition)
1. Check the rocker shaft and rocker bushings for
signs of damage and excessive wear. Measure
the rocker shaft diameter and rocker bearing
bushes to confirm they are within service limits,
refer to Technical Data (PIL 15-42). Note: The
rocker bearing bushes are not renewable. If
a rocker bearing bush is damaged or worn
the rocker must be renewed as a complete
assembly.
2. Make sure that all oil-ways and cross drillings in
the rocker shaft and pedestals are clear and free
from debris. Use an air line to blow through cross
drillings.
22. 15 - Engine
42 - Rocker and Fittings
00 - General
15 - 154 9813/6700-1 15 - 154
Remove and Install
Before Removal
1. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
2. Get access to the engine.
3. Disconnect and remove the fuel pipes from the
fuel injectors, refer to Fuel pipes (PIL 18-96).
4. Remove the rocker cover, refer to (PIL 15-42).
Figure 160.
3
1
2
2
2
2
2
2
2
2
2
2
8
7
4
5
6
9
10
1 Rocker assembly 2 Rocker shaft fixing bolts (x11)
3 Rocker shaft - oil feed pedestal fixing bolt (x1) 4 Pedestals (x11)
5 Oil feed pedestal (x1) 6 Rockers - exhaust (x6)
7 Rockers - inlet (x6) 8 Wave washers (x6)
9 Bridge pieces (x12) 10 Push rods (x12)
23. 15 - Engine
42 - Rocker and Fittings
00 - General
15 - 155 9813/6700-1 15 - 155
Remove
1. Remove the rocker shaft fixing bolts. DO NOT
withdraw the bolts. Lift the rocker shaft assembly
from the cylinder head complete with pedestals
still attached. Important: Keep all pedestals and
fixing bolts in their original positions.
2. Lift off the bridge pieces from the pairs of inlet
and exhaust valves.
3. Withdraw the push rods from the cylinder block.
Before Installation
1. Make sure that all items are clean and free from
damage and corrosion. If components within the
rocker assembly are damaged or worn. Refer to
Check (Condition) (PIL 15-42).
2. Make sure that all oil-ways and cross drillings in
the cylinder head, rocker shaft and pedestals are
clear and free from debris. Use an air line to blow
through the cross drillings.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Use a suitable degreasing agent to clean the top
of the cylinder head.
3. Install the bridge pieces on to the pairs of inlet
and exhaust valves in the cylinder head.
4. Insert the push rods into the cylinder block. Make
sure that they engage with the camshaft tappets.
5. Install the rocker shaft assembly into the cylinder
head. Make sure that the pedestals are located in
their original positions. Note the position of the oil
feed pedestal and the longer bolt. Make sure that
the push rods engage with the tappet adjusters
and that the rockers are located over the bridge
pieces.
6. Tighten the bolts to the correct torque value.
After Installation
1. Measure and adjust the valve clearances, refer
to (PIL 15-30).
Table 68. Torque Values
Item Nm
2 24
3 24