This service manual provides instructions for servicing the braking system of dumpers. It contains information on health and safety when working on the brakes, technical specifications, component identification, troubleshooting, and bleeding the brakes. The braking system uses mineral oil and contains separate front and rear brake circuits for safety. Adjustment is generally not needed as the brakes are self-adjusting, but bleeding may be required if the brake lines leak fluid.
New holland tc5.30 combine harvesters service repair manualfujsefkksemm
The document is a service manual that provides instructions for removing and installing various engine components on a TC5.30 combine. It includes sections on the engine, clutch, transmission, front and rear axles, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage. The manual uses a coding system to uniquely identify each technical procedure and includes specifications, functional descriptions, diagnostics, and service instructions.
New holland cx780 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]fujsefkksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland b115 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety rules are also outlined to prevent personal injury and machine damage while working.
New holland cx5090 laterale combine harvesters service repair manualfujsefkksemm
This document is a service manual for CNH Industrial combine harvesters. It contains over 200 sections organized by major vehicle systems. The sections provide information on maintenance, repair and replacement of components for the engine, transmission, axles, hydraulics, electrical systems, cab climate control, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading systems. The manual applies to several CX5000 and CX6000 series combine harvester models.
New holland b100 c backhoe loader service repair manualfujsefkksemm
This document is a service manual that contains instructions and specifications for maintenance and repair of backhoe loaders. It includes sections on safety rules, maintenance, technical specifications, dimensions and performance data. The technical specifications section provides details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets and tires of the backhoe loaders. The document also has sections that provide instructions for removing and installing major components like the engine, transmission, radiator and hood.
New holland cx820 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland CX combine harvester model. The key components include a closed-center load sensing variable displacement pump that supplies oil to circuits in the main frame stack valve and straw elevator stack valve. These circuits control functions like header height, unloading tube, straw elevator, reel adjustment, and lateral flotation. Hydraulic motors and cylinders powered by the system perform tasks like steering, header lifting, and reel operation.
New holland tc5.30 combine harvesters service repair manualfujsefkksemm
The document is a service manual that provides instructions for removing and installing various engine components on a TC5.30 combine. It includes sections on the engine, clutch, transmission, front and rear axles, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage. The manual uses a coding system to uniquely identify each technical procedure and includes specifications, functional descriptions, diagnostics, and service instructions.
New holland cx780 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]fujsefkksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland b115 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety rules are also outlined to prevent personal injury and machine damage while working.
New holland cx5090 laterale combine harvesters service repair manualfujsefkksemm
This document is a service manual for CNH Industrial combine harvesters. It contains over 200 sections organized by major vehicle systems. The sections provide information on maintenance, repair and replacement of components for the engine, transmission, axles, hydraulics, electrical systems, cab climate control, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading systems. The manual applies to several CX5000 and CX6000 series combine harvester models.
New holland b100 c backhoe loader service repair manualfujsefkksemm
This document is a service manual that contains instructions and specifications for maintenance and repair of backhoe loaders. It includes sections on safety rules, maintenance, technical specifications, dimensions and performance data. The technical specifications section provides details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets and tires of the backhoe loaders. The document also has sections that provide instructions for removing and installing major components like the engine, transmission, radiator and hood.
New holland cx820 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland CX combine harvester model. The key components include a closed-center load sensing variable displacement pump that supplies oil to circuits in the main frame stack valve and straw elevator stack valve. These circuits control functions like header height, unloading tube, straw elevator, reel adjustment, and lateral flotation. Hydraulic motors and cylinders powered by the system perform tasks like steering, header lifting, and reel operation.
New holland cx6.90 laterale fpt cursor 9 tier 4 b stage ivstage iv combine ha...fujsefkksemm
This service manual provides maintenance and repair information for several CNH combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains over 200 sections covering topics such as the engine, transmission, hydraulic systems, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and unloading. Each section provides technical specifications, descriptions of operation, troubleshooting information, and repair instructions for the various components and systems.
New holland br6090 round balers service repair manualfujsefkksemm
This document is a service manual that contains information on maintenance and repair for BR6080 and BR6090 machines. It includes sections on hydraulic, pneumatic, electrical, and electronic systems, as well as chapters on power production, power train, travel, crop processing, and more. Safety protocols are provided, including warnings to only allow trained technicians to perform repairs and to always stop engines and relieve pressures before working on the machines.
New holland b110 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 clr stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains information on engine systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, and electrical systems. The manual provides part numbers and repair instructions for maintenance and troubleshooting of components.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...fujsefkksemm
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and procedures for reassembling components. It also describes recommended service tools and procedures for pressing parts, applying proper bolt torque, and using torque wrenches and extensions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...fujsefkksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a 432F BACKHOE LOADER model with a C4.4 engine. The procedure involves using special tools to compress the valve springs, rotate the crankshaft to position the piston, and remove/install the valve spring retainers and springs. Proper cleaning and inspection of parts is emphasized to prevent contaminants from causing premature wear.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...fujsefkksemm
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, seals, brakes and differentials. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims selected to achieve proper torque specifications. Springs and pins are installed and nuts are staked to complete the assembly.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...fujsefkksemm
This service repair manual provides instructions for assembling the transmission of a 432F backhoe loader. It lists the required tools and presents a step-by-step procedure with illustrations. Some key steps include installing bearings, seals, gears, shafts, springs, and pistons into the transmission case. Precautions are given for working with compressed springs. The transmission components are assembled in sections, including the input shaft, reverse shaft, direct drive shafts, and output shafts.
Komatsu pc138 us 8 crawler excavator parts catalogue manual - sn 20001-24509fujsefkksemm
This document provides parts information for a PC138US-8 excavator with serial numbers 20001-24509. It includes lists of engine, cooling system, and other parts with part numbers, names, quantities, and applicable serial number ranges. The cooling system section includes radiator, oil cooler, after cooler, fuel cooler, piping, sub tank, and radiator mount parts.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h018...fujsefkksemm
This document provides instructions for servicing a 951B track loader model. It discusses general instructions for disassembly and assembly including safety procedures, cleaning parts, removal and installation techniques, and operating a rebuilt engine. It also describes various service tools such as pullers, push-pullers, and procedures like pressing parts, bolt torque, and using a torque wrench with an extension.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...fujsefkksemm
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, involving reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fujsefkksemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The 33 steps for assembly describe installing new components in the reverse order of disassembly and provide details on lubrication, torque specifications, and alignment marks to ensure proper reassembly. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...fujsefkksemm
This document provides disassembly instructions for a 432E backhoe loader transmission. It outlines 19 steps to fully disassemble the transmission, including removing gears, shafts, bearings, seals, and other components. Special tools are required for tasks like removing bearings. Safety precautions are noted, such as wearing protective equipment when compressing springs. The transmission is weighty and must be properly supported throughout disassembly.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
The document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts to detach the front housing from the cylinder block and oil pan.
2) Installing a new gasket and bolts to reattach the front housing, ensuring proper alignment.
3) Tightening bolts to the specified torque and installing related components like the camshaft gear and front gear group.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3054 engine. It outlines the required tools, safety notices, and step-by-step procedures. To remove the pump, the technician must first remove other components like the water pump and fuel lines. They then use timing pins to align holes on the pump, gear, and body before removing bolts. Installation involves checking the O-ring seal, lubricating it, and mounting the pump while aligning timing marks. The document ensures the work is done with care to contain fluids and maintain correct timing.
Caterpillar cat 432 e backhoe loader (prefix bxe) service repair manual (bxe0...fujsefkksemm
This document provides instructions for removing and installing various engine components on a Caterpillar 432E backhoe loader, including:
- Removing and installing V-belts
- Removing and installing the fan, fan drive, and alternator
- Procedures include removing set screws, disconnecting wiring harnesses, adjusting belt tension, and reconnecting components.
The summary provides an overview of the types of components covered in the repair manual and the basic removal and installation steps involved without including excessive technical details.
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...fujsefkksemm
This document provides instructions for removing and installing an engine oil cooler and engine oil relief valve on a Caterpillar 3054C engine. The summary is:
1. Drain coolant and oil from the engine oil cooler before removing housing bolts and seals.
2. Clean mating surfaces and install new seals and gasket before bolting the housing back onto the engine with new bolts.
3. Remove the plug and spring to access the engine oil relief valve plunger. Inspect parts and lubricate before reinstalling.
4. Drain the oil pan before removing bolts to access the engine oil pump. Remove bolts and suction pipe to remove the pump assembly.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine. It includes the following steps:
1. To remove the engine oil pump, remove the oil pan, front housing, strainer, suction pipe, and oil relief valve. Then remove three bolts to take off the pump.
2. To disassemble the water pump, drain the coolant, remove eight bolts and two nuts to take off the pump. Then remove six bolts on the cover, an O-ring seal, gear using a special tool, and seal using a lever.
3. The document provides detailed illustrations and torque specifications for reinstalling
Caterpillar cat 434 e backhoe loader (prefix sxb) service repair manual (sxb0...fujsefkksemm
The document provides instructions for installing a transmission on a 434E backhoe loader. It describes 25 steps for the installation, including attaching the transmission assembly with a hydraulic jack, installing mounting hardware, connecting hydraulic and electrical lines, and filling the transmission with oil once installed. Tools required include a jack, jack stands, pins, and tubes for supporting the transmission assembly.
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...fujsefkksemm
This document provides instructions for removing and assembling components of a Caterpillar 3054C engine, including the cylinder head. The removal procedure for the cylinder head involves first draining fluids, removing related components like the exhaust manifold and fuel injectors, and then loosening and removing mounting screws to lift the cylinder head off the engine block. Proper care is emphasized to prevent damage to parts and contain fluids during disassembly.
New holland cx6.90 laterale fpt cursor 9 tier 4 b stage ivstage iv combine ha...fujsefkksemm
This service manual provides maintenance and repair information for several CNH combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains over 200 sections covering topics such as the engine, transmission, hydraulic systems, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and unloading. Each section provides technical specifications, descriptions of operation, troubleshooting information, and repair instructions for the various components and systems.
New holland br6090 round balers service repair manualfujsefkksemm
This document is a service manual that contains information on maintenance and repair for BR6080 and BR6090 machines. It includes sections on hydraulic, pneumatic, electrical, and electronic systems, as well as chapters on power production, power train, travel, crop processing, and more. Safety protocols are provided, including warnings to only allow trained technicians to perform repairs and to always stop engines and relieve pressures before working on the machines.
New holland b110 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 clr stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains information on engine systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, and electrical systems. The manual provides part numbers and repair instructions for maintenance and troubleshooting of components.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...fujsefkksemm
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and procedures for reassembling components. It also describes recommended service tools and procedures for pressing parts, applying proper bolt torque, and using torque wrenches and extensions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...fujsefkksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a 432F BACKHOE LOADER model with a C4.4 engine. The procedure involves using special tools to compress the valve springs, rotate the crankshaft to position the piston, and remove/install the valve spring retainers and springs. Proper cleaning and inspection of parts is emphasized to prevent contaminants from causing premature wear.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...fujsefkksemm
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, seals, brakes and differentials. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims selected to achieve proper torque specifications. Springs and pins are installed and nuts are staked to complete the assembly.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...fujsefkksemm
This service repair manual provides instructions for assembling the transmission of a 432F backhoe loader. It lists the required tools and presents a step-by-step procedure with illustrations. Some key steps include installing bearings, seals, gears, shafts, springs, and pistons into the transmission case. Precautions are given for working with compressed springs. The transmission components are assembled in sections, including the input shaft, reverse shaft, direct drive shafts, and output shafts.
Komatsu pc138 us 8 crawler excavator parts catalogue manual - sn 20001-24509fujsefkksemm
This document provides parts information for a PC138US-8 excavator with serial numbers 20001-24509. It includes lists of engine, cooling system, and other parts with part numbers, names, quantities, and applicable serial number ranges. The cooling system section includes radiator, oil cooler, after cooler, fuel cooler, piping, sub tank, and radiator mount parts.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h018...fujsefkksemm
This document provides instructions for servicing a 951B track loader model. It discusses general instructions for disassembly and assembly including safety procedures, cleaning parts, removal and installation techniques, and operating a rebuilt engine. It also describes various service tools such as pullers, push-pullers, and procedures like pressing parts, bolt torque, and using a torque wrench with an extension.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...fujsefkksemm
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, involving reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fujsefkksemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The 33 steps for assembly describe installing new components in the reverse order of disassembly and provide details on lubrication, torque specifications, and alignment marks to ensure proper reassembly. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 432 e backhoe loader (prefix jba) service repair manual (jba0...fujsefkksemm
This document provides disassembly instructions for a 432E backhoe loader transmission. It outlines 19 steps to fully disassemble the transmission, including removing gears, shafts, bearings, seals, and other components. Special tools are required for tasks like removing bearings. Safety precautions are noted, such as wearing protective equipment when compressing springs. The transmission is weighty and must be properly supported throughout disassembly.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
The document provides instructions for removing and installing the front housing on a Caterpillar 3054 engine. It describes:
1) Removing bolts to detach the front housing from the cylinder block and oil pan.
2) Installing a new gasket and bolts to reattach the front housing, ensuring proper alignment.
3) Tightening bolts to the specified torque and installing related components like the camshaft gear and front gear group.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3054 engine. It outlines the required tools, safety notices, and step-by-step procedures. To remove the pump, the technician must first remove other components like the water pump and fuel lines. They then use timing pins to align holes on the pump, gear, and body before removing bolts. Installation involves checking the O-ring seal, lubricating it, and mounting the pump while aligning timing marks. The document ensures the work is done with care to contain fluids and maintain correct timing.
Caterpillar cat 432 e backhoe loader (prefix bxe) service repair manual (bxe0...fujsefkksemm
This document provides instructions for removing and installing various engine components on a Caterpillar 432E backhoe loader, including:
- Removing and installing V-belts
- Removing and installing the fan, fan drive, and alternator
- Procedures include removing set screws, disconnecting wiring harnesses, adjusting belt tension, and reconnecting components.
The summary provides an overview of the types of components covered in the repair manual and the basic removal and installation steps involved without including excessive technical details.
Caterpillar cat 432 d backhoe loader (prefix wep) service repair manual (wep0...fujsefkksemm
This document provides instructions for removing and installing an engine oil cooler and engine oil relief valve on a Caterpillar 3054C engine. The summary is:
1. Drain coolant and oil from the engine oil cooler before removing housing bolts and seals.
2. Clean mating surfaces and install new seals and gasket before bolting the housing back onto the engine with new bolts.
3. Remove the plug and spring to access the engine oil relief valve plunger. Inspect parts and lubricate before reinstalling.
4. Drain the oil pan before removing bolts to access the engine oil pump. Remove bolts and suction pipe to remove the pump assembly.
Caterpillar cat 438 c backhoe loader (prefix 1jr) service repair manual (1jr0...fujsefkksemm
This document provides instructions for removing and disassembling the engine oil pump and water pump on a Caterpillar 3054 engine. It includes the following steps:
1. To remove the engine oil pump, remove the oil pan, front housing, strainer, suction pipe, and oil relief valve. Then remove three bolts to take off the pump.
2. To disassemble the water pump, drain the coolant, remove eight bolts and two nuts to take off the pump. Then remove six bolts on the cover, an O-ring seal, gear using a special tool, and seal using a lever.
3. The document provides detailed illustrations and torque specifications for reinstalling
Caterpillar cat 434 e backhoe loader (prefix sxb) service repair manual (sxb0...fujsefkksemm
The document provides instructions for installing a transmission on a 434E backhoe loader. It describes 25 steps for the installation, including attaching the transmission assembly with a hydraulic jack, installing mounting hardware, connecting hydraulic and electrical lines, and filling the transmission with oil once installed. Tools required include a jack, jack stands, pins, and tubes for supporting the transmission assembly.
Caterpillar cat 432 d backhoe loader (prefix tdr) service repair manual (tdr0...fujsefkksemm
This document provides instructions for removing and assembling components of a Caterpillar 3054C engine, including the cylinder head. The removal procedure for the cylinder head involves first draining fluids, removing related components like the exhaust manifold and fuel injectors, and then loosening and removing mounting screws to lift the cylinder head off the engine block. Proper care is emphasized to prevent damage to parts and contain fluids during disassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. 18 - Fuel and Exhaust System
96 - Fuel Pipe
03 - High Pressure Pipe
18 - 79 9813/5350-2 18 - 79
03 - High Pressure Pipe
Remove and Install
Special Tools
Description Part No. Qty.
Socket 17MM Offset -
(HP Fuel pipes)
331/27987 1
Torque Wrench
(10-100Nm)
993/70111 1
Important. Before disconnecting or removing fuel
pipes proceed as follows.
1. Make sure that you have the correct new parts.
1.1. The high pressure fuel pipes MUST BE
REPLACED with new ones.
1.2. The new fuel pipes must remain sealed
inside their bags before use. If a bag is open
DO NOT USE the fuel pipe, get a new one.
2. Obey all fuel system health and safety
information. Refer to (PIL 18-00).
3. Make sure that the engine is safe to work on.
3.1. The engine must cool and pressure in the
fuel system must decay before you start
work.
3.2. If the engine has been running, wait at least
one hour before you start work.
4. Clean the engine. Refer to Engine, Clean (PIL
15-00-00).
5. Remove the protective cover as follows.
Figure 300.
C
B
A
A Screw
B Plastic segment
C Protective cover
5.1. Push out the plastic segments.
5.2. Remove the screws and lift off the cover.
5.3. Remove any dirt or debris that is exposed.
Refer to Engine, Clean (PIL 15-00-00).
6. Always use a spanner at the top of the fuel pipe
nut (this will prevent damage to the nut).
Figure 301.
Injector Fuel Pipes
Remove
The procedure describes how to remove one fuel
pipe.
Figure 302.
E
A
B
D
C
A Fuel pipe
B Nut 1
C Fuel injector
D Fuel rail
E Nut 2
1. Remove the fuel pipes one at a time as follows.
1.1. Loosen the nut 2 at the fuel rail. Do not
remove the nut at this step.
1.2. Use the 17mm deep socket special tool at
the top of nut. This will prevent damage to
the nut.
3. 18 - Fuel and Exhaust System
96 - Fuel Pipe
03 - High Pressure Pipe
18 - 80 9813/5350-2 18 - 80
Special Tool: Socket 17MM Offset - (HP
Fuel pipes) (Qty.: 1)
Special Tool: Torque Wrench (10-100Nm)
(Qty.: 1)
1.3. Push the fuel pipe against the injector cone
and at the same time remove the nut 1.
1.4. Push the fuel pipe against the fuel rail cone
and at the same time remove the nut 2.
1.5. Make sure that there is no dirt or debris on
the fuel pipe or the connectors.
1.6. Remove the fuel pipe.
1.7. Seal all the open ports, use the correct parts
from the service kit.
2. Repeat step 1 to remove the other fuel pipes.
3. Discard the old fuel pipes.
Install
Important: The high pressure fuel pipes must be
replaced with new ones. The new fuel pipes must
remain sealed inside their bags before use. If a bag
is open do not use the fuel pipe, get a new one. Do
not open the bag until you are ready to assemble the
fuel pipe.
1. Make sure that the bleed-off adaptors are
assembled on the injectors before you install the
high pressure pipes.
2. Assemble the fuel pipes one at a time. The
procedure describes how to assemble one fuel
pipe.
2.1. Put the correct end of the fuel pipe against
the correct injector cone.
2.2. Tighten the nut 1 with your hand.
2.3. Put the other end of the fuel pipe against the
correct fuel rail cone.
2.4. Tighten the nut 2 with your hand.
2.5. Nuts must be tightened in the correct
sequence. Tighten nut 1 and then nut 2.
2.6. Use the special tool at the top of nut 1 and
tighten it to the correct torque value.
Torque: 27N·m
Special Tool: Socket 17MM Offset - (HP
Fuel pipes) (Qty.: 1)
2.7. Put the spanner at the top of nut 2 and
tighten it to the correct torque value.
Torque: 27N·m
Injection Pump to Rail Fuel Pipe
Remove
Figure 303.
D
C
E
A
B
A Nut 1
B Fuel rail
C Injection pump
D Nut 2
E Fuel pipe
1. Remove the fuel pipe as follows.
1.1. Loosen the nut 2. Do not remove the nut at
this step.
1.2. Use the 17mm deep socket special tool at
the top of nut. This will prevent damage to
the nut.
Special Tool: Socket 17MM Offset - (HP
Fuel pipes) (Qty.: 1)
Special Tool: Torque Wrench (10-100Nm)
(Qty.: 1)
1.3. Push the fuel pipe against the injector cone
and at the same time remove the nut 1.
1.4. Push the fuel pipe against the rail cone and
at the same time remove the nut 2.
1.5. Make sure that there is no dirt or debris on
the fuel pipe or the connectors.
1.6. Remove the fuel pipe.
1.7. Seal all the open ports, use the correct parts
from the service kit.
2. Discard the old fuel pipe.
4. 18 - Fuel and Exhaust System
96 - Fuel Pipe
03 - High Pressure Pipe
18 - 81 9813/5350-2 18 - 81
Install
Important: The high pressure fuel pipes must be
replaced with new ones. The new fuel pipes must
remain sealed inside their bags before use. If a bag
is open do not use the fuel pipe, get a new one. Do
not open the bag until you are ready to assemble the
fuel pipe.
1. To assemble the fuel pipe.
1.1. Put the correct end of the fuel pipe against
the correct pump cone at the injection
pump.
1.2. Tighten the nut 2 with your hand.
1.3. Put the other end of the fuel pipe against the
correct fuel rail cone.
1.4. Tighten the nut 1 with your hand.
1.5. Nuts must be tightened in the correct
sequence. Tighten nut 2 and then nut 1.
1.6. Use the special tool at the top of nut 2 and
tighten it to the correct torque value.
Torque: 27N·m
Special Tool: Socket 17MM Offset - (HP
Fuel pipes) (Qty.: 1)
1.7. Put the spanner at the top of nut 1 and
tighten it to the correct torque value.
Torque: 27N·m
After Installation
1. Ensure that all pipes are correctly installed
and located in retaining clips as applicable. If
retaining clips are missing or damaged they must
be replaced or renewed
2. Start the engine and check for fuel leaks.
5. 18 - Fuel and Exhaust System
96 - Fuel Pipe
06 - Low Pressure Pipe
18 - 82 9813/5350-2 18 - 82
06 - Low Pressure Pipe
Remove and Install
Before Removal
Obey all fuel system health and safety information.
Refer to Fuel System, Health and Safety (PIL 18-00).
Low Pressure Fuel Pipes
Remove
The low pressure fuel pipes have a nylon fitting
attached to the pipe that replaces the nut and olive.
The fittings are part of the pipe and not a separate
item.
1. To release the fuel pipe, first press and hold the
release buttons (one each side of the coupler).
Push the coupler towards the connector spigot
and then withdraw.
2. Cap all open ports to prevent ingress of dirt and
debris.
Assemble
1. To install the fuel pipe, press and hold the release
buttons. Push the coupler over the connector
spigot and release the button. The connector will
be heard to click when it is fully home and locked
in place.
2. To check that the connection has been fully
made, attempt to pull the connector from the
connector spigot without releasing the lock
mechanism. (A gentle pull is all that is required,
if the connection is not correct the connector will
release very easily.)
Figure 304.
B
A
C
A
A Release Buttons
B Coupler
C Spigot
After Assembly
1. Make sure that all the fuel pipes are correctly
installed and located in the retaining clips as
applicable. If retaining clips are missing or
damaged, they must be replaced or renewed.
2. Start the engine and check for fuel leaks.
Injector Bleed-off Pipes
Before Removal
Obey all fuel system health and safety information.
Refer to (PIL 18-00).
1. Make sure that the engine is safe to work on. The
engine must cool and pressure in the fuel system
must decay before you start work. If the engine
has been running, wait at least one hour before
you start work.
2. Clean the engine. Refer to Engine, Clean (PIL
15-00).
3. Remove the protective cover as follows.
6. 18 - Fuel and Exhaust System
96 - Fuel Pipe
06 - Low Pressure Pipe
18 - 83 9813/5350-2 18 - 83
3.1. Push out the plastic segments.
3.2. Remove the screws and lift off the cover.
Figure 305.
C
B
A
A Screw
B Plastic segment
C Protective cover
3.3. Remove any dirt or debris that is exposed.
Refer to Engine, Clean (PIL 15-00).
4. To remove the bleed pipe clips, remove the high
pressure fuel pipes first. Refer to (PIL 18-96-03).
5. DO NOT try to repair fuel pipes or connectors.
Defective fuel pipe assemblies must be replaced.
Remove
The following details the removal and replacement
of one bleed-off connector. The procedure for the
remaining connectors is identical.
1. Gently spring the location tabs apart and pull out
the bleed pipe connector. DO NOT use excessive
force on the tabs.
2. Remove and discard the O-ring.
3. If it is necessary to remove the bleed off pipe
assembly, remove the nylon fitting at the high
pressure pump.
4. Cap all open ports to prevent ingress of dirt and
debris.
Install
1. Install a new O-ring.
2. Push in the bleed pipe connector until the
location tabs snap over the connector.
3. If applicable, replace the high pressure fuel pipes
with new ones. DO NOT use a high pressure fuel
pipe that was removed. Refer to (PIL 18-96-03)
Figure 306.
C
A
D
B
A Location tabs
B Bleed pipe connector
C Bleed pipe clip
D High pressure fuel pipe
After Assembly
1. Make sure that all pipes are correctly installed
and located in retaining clips as applicable. If the
retaining clips are missing or damaged they must
be replaced or renewed.
2. Start the engine and check for fuel leaks.
3. Install the protective cover. Refer to Figure 305.
7. 24 - Brake System
00 - Brake System
00 - General
24 - 3 9813/5350-2 24 - 3
00 - General
Introduction ...................................................... 24-3
Health and Safety ........................................... 24-4
Technical Data ................................................. 24-5
Component Identification ................................. 24-6
Fault-Finding .................................................... 24-7
Bleed ............................................................... 24-8
Introduction
(For: 10TFT, 9TFT)
Under no circumstances allow conventional brake
fluid to be added to the system, never purge the
system and refill with brake fluid. Otherwise damage
will occur to all the rubber sealing components within
the brake system. Use only mineral based hydraulic
oil.
The machine uses axles with oil immersed totally
enclosed multi plate brakes. The machines have
front and rear brakes, operating on independent
circuits that gives dual circuit safety.
The brake system uses a tandem master cylinder
and is filled with mineral oil through a remotely
mounted fluid reservoir located behind the access
panel on the front of the seat support.
Normally adjustment of the brakes is not necessary
as they adjust automatically by design. Bleeding of
the system may be necessary if the system pipework
is damaged causing system leakage.
The dumper has a park brake system which is
integral with the disc and caliper installed to the
gearbox output shaft and is operated by a park brake
located to the right of the operator seat.
8. 24 - Brake System
00 - Brake System
00 - General
24 - 4 9813/5350-2 24 - 4
Health and Safety
Brake Fluid
Use of incorrect brake fluid will cause serious
damage to the seals of the braking system. This will
result in brake failure.
Service Brake Bleeding
Before bleeding the service brake system, park on
level ground and set the park brake to on. Put blocks
on both sides of the wheels on one axle to prevent
the machine rolling. Stop the engine and disconnect
the battery so that the engine cannot be started. If
you do not take these precautions the machine could
run over you.
Park Brake Maintenance
Before working on the park brake, park on level
ground and put blocks on both sides of all wheels
to prevent the machine rolling. Stop the engine and
disconnect the battery so that the engine cannot be
started. If you do not take these precautions the
machine could run over you.
Working Under the Machine
Make the machine safe before getting beneath it.
Make sure that any attachments on the machine are
correctly attached. Engage the park brake, remove
the ignition key, disconnect the battery. If the machine
has wheels use blocks to prevent unintentional
movement.
Brake Dust
Brake pads generate dust, which if inhaled may
endanger health. Wash off the caliper assemblies
before commencing work. Clean hands thoroughly
after completing the work.
Brake Dust
Brake shoes generate dust, which if inhaled
may endanger health. Make sure that dust is
removed correctly, particularly before installing
new components. Clean hands thoroughly after
completing the work.
Springs
Always wear personal protective equipment when
dismantling assemblies containing components
under pressure from springs. This will protect against
eye injury from components accidentally flying out.
Notice: Using incorrect fluid could damage the
system. See Fluids, Capacities and Lubricants for
the correct fluid. The fluid can harm your skin. Wear
rubber gloves. Cover cuts or grazes.
WARNING! Before working on the brake system,
make sure that the machine is on solid level ground.
Put blocks on all wheels to prevent the machine
rolling.
WARNING! Do not use the machine with any part of
its brake system disconnected or inoperative. When
the test has been completed, make sure all brake
system components are installed and the system is
operating correctly.
WARNING! Before testing the park brake make sure
the area around the machine is clear of people.
WARNING! If the machine starts to move during the
park brake test, immediately apply the foot brake and
reduce the engine speed.
WARNING! If the machine starts to move during the
service brake test, immediately reduce the engine
speed and apply the park brake.
WARNING! Do not use a machine with a faulty park
brake.
WARNING! Non approved modifications to drive
ratios, machine weight or wheel and tyre sizes may
adversely affect the performance of the park brake.
WARNING! Oil on the brake disc will reduce brake
effectiveness. Keep oil away from the brake disc.
Remove any oil from the disc with a suitable solvent.
Read and understand the solvent manufacturer's
safety instructions. If the pads are oily, install with the
new pads.
WARNING! Faulty brakes can kill. If you have to
top up the brake reservoir frequently, get the brake
system checked by your JCB Dealer. Do not use the
machine until the fault has been put right.
WARNING! The park brake must not be used to
slow the machine from travelling speed, except in an
emergency, otherwise the efficiency of the brake will
be reduced. Whenever the park brake has been used
in an emergency the brake friction components must
be renewed and the other components inspected.
Notice: Over adjustment or failure to disengage the
park brake properly will cause excessive wear of the
park brake mechanism.
9. 24 - Brake System
00 - Brake System
00 - General
24 - 5 9813/5350-2 24 - 5
Technical Data
(For: 10TFT, 9TFT)
Table 124.
Description Data
Brakes
Type Oil immersed disc type
in the axles
Master cylinder diameter 31.75mm
Master cylinder seals Specific for mineral oil
Brake discs
Type Manually adjusted
'Hayes' type caliper,
mounted on transmis-
sion output shaft
Friction disc diameter 279.4mm
Friction disc minimum
thickness
8.89mm
Friction disc maximum
thickness
9.65mm
Friction material thick-
ness on new pads
(1)
3.18mm
Torque values
Master cylinder retaining
bolts
60N·m
Park brake caliper bolt 230N·m
Park brake caliper
bracket bolt
45N·m
(1) Replace at 2mm
10. 24 - Brake System
00 - Brake System
00 - General
24 - 6 9813/5350-2 24 - 6
Component Identification
(For: 10TFT, 9TFT)
Figure 310.
C
B
A
D
E
F
A Front axle B Front axle brake bleed nipple
C Remote brake fluid tank D Master cylinder
E Rear axle brake bleed nipple F Rear axle
11. 24 - Brake System
00 - Brake System
00 - General
24 - 7 9813/5350-2 24 - 7
Fault-Finding
Fault
Insufficient braking Table 125. Page 24-7
Brake pedal is soft Table 126. Page 24-7
Overheating of the brake system Table 127. Page 24-7
Table 125. Insufficient braking
Cause Remedy
Incorrect adjustment Check the brake disc thickness. Adjust the brakes.
Worn out brake disc Check the brake disc thickness. Replace the brake
discs.
Incorrect brake fluid Drain the incorrect brake fluid. Replace all the seals
and hoses from the brake system. Fill the correct oil.
Loss of brake fluid Check the outside circuit and the master cylinder
for leaks. Repair as necessary. If the leak is to the
outside, replace the O-rings between the center and
the intermediate housings. If the leak is to the inside,
replace the all the O-rings.
Overheated axle causing brake fluid to vaporize Refer to overheating fault remedy.
See Also: Table 127. Overheating of the brake
system
Table 126. Brake pedal is soft
Cause Remedy
Air in the brake system Bleed the brake system.
Table 127. Overheating of the brake system
Cause Remedy
Wrong oil level Drain, flush and fill the brake oil to the correct level.
Too small brake gap Adjust the brakes.
Incorrect brake fluid in the system Drain the incorrect brake fluid. Replace all the seals
and hoses from the brake system. Fill the correct oil.
No free play of brake pedal at master cylinder Adjust the brake pedal free play.
Restrictions in the brake lines Check the condition of the brake lines. Replace as
necessary.
12. 24 - Brake System
00 - Brake System
00 - General
24 - 8 9813/5350-2 24 - 8
Bleed
(For: 10TFT, 9TFT)
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Isolate the battery.
Refer to: PIL 33-03-00.
3. Open the engine compartment cover.
Refer to: PIL 06-06-06.
4. Open the bleed nipple.
Figure 311. Front axle
A
A
A Bleed nipples
5. Press and hold the brake pedal down.
6. Tighten the bleed nipple.
7. Release the brake pedal.
8. Do the steps 4 to step 7 until all of the trapped air
is removed from the brake system.
9. Do the steps 4 to step 8 for the RH (Right Hand)
side brake.
10. Do the steps 4 to step 9 to bleed the rear brake
system.
Figure 312. Rear axle
A
A
A Bleed nipples
13. 24 - Brake System
03 - Service Brake
01 - Master Cylinder
24 - 12 9813/5350-2 24 - 12
Remove and Install
(For: 10TFT, 9TFT)
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Isolate the battery.
Refer to: PIL 33-03-00.
3. Remove the floorplate.
Refer to: PIL 09-78-00.
4. Disconnect the front brake pipe, rear brake pipe
and the brake fluid tank from the master cylinder.
Figure 313.
C
D
ACB
A Front brake pipe
B Rear brake pipe
C Brake fluid tank
D Master cylinder
5. Remove the bolts.
6. Remove the master cylinder from the machine.
Figure 314.
E
D
D Master cylinder
E Bolts
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
step.
2. Tighten the bolts to the correct torque value.
Table 128. Torque Values
Item Description Nm
E Bolts 60
14. 24 - Brake System
18 - Park Brake
06 - Cable
24 - 15 9813/5350-2 24 - 15
06 - Cable
Adjust ............................................................ 24-15
Remove and Install ....................................... 24-16
Adjust
(For: 10TFT, 9TFT)
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Remove the floorplate.
Refer to: PIL 09-78-00.
3. Isolate the battery.
Refer to: PIL 33-03-00.
4. Remove the plastic hand grip from the park brake
lever.
Figure 315.
A
A Plastic hand grip
5. Loosen the locking grub screw.
6. Rotate the adjusting nut in an anticlockwise
direction to give free play in the cable.
Figure 316.
B
C
B Grub screw
C Adjusting nut
7. Adjust the cable so that the specified length of
thread protrudes through the locknut.
Dimension: 5mm
8. Tighten the nut against the back of the bracket.
15. 24 - Brake System
18 - Park Brake
06 - Cable
24 - 16 9813/5350-2 24 - 16
Figure 317.
D
F
E
D Park brake cable
E Locknut
F Nut
9. Rotate the adjusting nut on the park brake lever
in a clockwise direction until the free play in the
cable has been taken up. Correct adjustment is
achieved when there is no free play in the cable
and no pressure on the brake lever.
10. Tighten the locking grub screw.
11. Install the plastic hand grip to the park brake
lever.
Remove and Install
(For: 10TFT, 9TFT)
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Isolate the battery.
Refer to: PIL 33-03-00.
3. Remove the floorplate.
Refer to: PIL 09-78-00.
4. Release the park brake.
5. Disconnect the park brake cable from the caliper.
Figure 318.
A
A Park brake cable
6. Disconnect the park brake cable from the
reaction bracket.
Figure 319.
B
A
A Park brake cable
B Reaction bracket
7. Remove the split pin.
8. Disconnect the park brake cable from the park
brake handle.
16. 24 - Brake System
18 - Park Brake
06 - Cable
24 - 17 9813/5350-2 24 - 17
Figure 320.
H
J
H Split pin
J Park brake handle
9. Loosen the locknut.
10. Disconnect the park brake cable from the
bracket.
Figure 321.
K
L
K Locknut
L Bracket
11. Make a note of the route and the position of the
cable to help installation.
12. Remove the park brake cable from the chassis.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
step.
2. Adjust the park brake cable.
Refer to: PIL 24-18-06.
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. 24 - Brake System
18 - Park Brake
18 - Caliper
24 - 18 9813/5350-2 24 - 18
18 - Caliper
Remove and Install
(For: 10TFT, 9TFT)
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Isolate the battery.
Refer to: PIL 33-03-00.
3. Remove the floorplate.
Refer to: PIL 09-78-00.
4. Release the park brake.
5. Disconnect the park brake cable from the caliper.
Figure 322.
A
A Park brake cable
6. Disconnect the park brake cable from the
reaction bracket.
Figure 323.
B
A
A Park brake cable
B Reaction bracket
7. Remove the bolts.
8. Remove the park brake caliper from the machine.
Figure 324.
D
C
C Park brake caliper
D Bolts
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
1.1. Tighten the bolts to the correct torque value.
1.2. Adjust the park brake cable. Refer to (PIL
24-18).
Table 129. Torque Values
Item Description Nm
D Bolts 230
19. 25 - Steering System
06 - Steer Unit/Valve
00 - General
25 - 8 9813/5350-2 25 - 8
Check (Condition)
Consumables
Description Part No. Size
Surface Cleaning Fluid 4103/1204 1L
1. Examine all contact surfaces and replace any
parts that have scratches, wear or other damage
that could cause leakage.
2. Do not use abrasive or try to file or grind the
surfaces.
3. Clean all metal parts with a solvent and blow dry
with an air line.
Consumable: Surface Cleaning Fluid
Remove and Install
(For: 10TFT, 9TFT)
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Isolate the battery.
Refer to: PIL 33-03.
3. Remove the floor plate.
Refer to: PIL 09-78-00.
4. Remove the bolts 1.
5. Remove the steering column cover.
Refer to: PIL 25-12-06.
6. Remove the cable ties.
Figure 325.
A
A Cable ties
7. Disconnect the hoses from the steer unit.
8. Put a label on the hoses to help installation.
9. Plug all the open ports and hoses to prevent
contamination.
20. 25 - Steering System
06 - Steer Unit/Valve
00 - General
25 - 9 9813/5350-2 25 - 9
Figure 326.
B
B Hoses
10. Remove the grease nipple.
11. Remove the bolts 2.
12. Disconnect the steer valve from the steering
column.
Figure 327.
J
K
L
J Grease nipple
K Steer valve
L Bolts 2
13. Rotate the steer valve anti-clockwise and remove
the steer valve from the machine.
Figure 328.
K
K Steer valve
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Align the steering column splines to the steer
unit.
3. Tighten the bolts to the correct torque value.
4. Check the hydraulic oil level and top up as
required.
Refer to: PIL 30-00-00.
Table 131. Torque Values
Item Description Nm
L Bolts 2 60