This service manual section provides instructions for servicing the main bearings of an engine crankshaft. It describes removing and installing the main bearing caps and shells. The procedure involves draining oil, removing components like the oil sump and fuel injectors for access. Marks are placed on caps and shells are replaced since they must not be reused. Torque wrenches are the only special tool needed, and bolts are not reused. Care is taken due to fracture split surfaces on caps and rods.
Jcb hydradig 110 w wheeled excavator service repair manual (serial no. from 2...fiskefjskemem
This document provides instructions for removing and installing the oil sump on a JCB Hydradig 110W wheeled excavator. It begins with an introduction to the engine's lubrication system and the role of the oil sump. The component identification section outlines the main parts of the oil sump. The removal and installation section provides a step-by-step process for accessing the engine and safely removing the oil sump, replacing gaskets, and reinstalling the sump. Proper torque values for fasteners are also included.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualfujsefxdeksemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and side counterweights. The counterweight is removed using an eyebolt and lifting device. Fenders are removed using eyebolts through mount holes and lifted away. The hood assembly can be pivoted or completely removed using a lifting device attached to the spine. The hydraulic tank is removed by disconnecting hoses, removing mounting hardware, and lifting it away while supported.
Hyster c008 (h370 c) forklift service repair manualfujsefxdeksemm
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from outlet oil.
Hyster b187 (s50 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Hyster b187 (s40 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...fujsefxdeksemm
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...fujsefxdeksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
Jcb hydradig 110 w wheeled excavator service repair manual (serial no. from 2...fiskefjskemem
This document provides instructions for removing and installing the oil sump on a JCB Hydradig 110W wheeled excavator. It begins with an introduction to the engine's lubrication system and the role of the oil sump. The component identification section outlines the main parts of the oil sump. The removal and installation section provides a step-by-step process for accessing the engine and safely removing the oil sump, replacing gaskets, and reinstalling the sump. Proper torque values for fasteners are also included.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
Hyster e019 (h12.00 xm 12ec europe) forklift service repair manualfujsefxdeksemm
This document provides instructions for repairing components on a forklift, including the counterweight, fenders, hood, hydraulic tank, and side counterweights. The counterweight is removed using an eyebolt and lifting device. Fenders are removed using eyebolts through mount holes and lifted away. The hood assembly can be pivoted or completely removed using a lifting device attached to the spine. The hydraulic tank is removed by disconnecting hoses, removing mounting hardware, and lifting it away while supported.
Hyster c008 (h370 c) forklift service repair manualfujsefxdeksemm
1) Gear pumps come in single stage or tandem designs and work by using rotating gears to move oil from an inlet port to an outlet port. Seals are used to prevent leaks between sections.
2) As pressure increases, devices keep the clearance between gears at a minimum to prevent leakage while still allowing for lubrication and reducing wear.
3) When the drive gear turns, it engages with the driven gear, moving oil from the inlet chamber around the pumping chamber and out the outlet chamber. Lubrication is provided to gears and bearings from outlet oil.
Hyster b187 (s50 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Hyster b187 (s40 xl) forklift service repair manualfujsefxdeksemm
This document provides information about the service repair of lift trucks models S40XL, S50XL, and S60XL. It discusses the hydraulic system, lift system pressures and flows, mast speeds, and steering system components and operation. Specifically:
- It lists the weights and specifications of the three lift truck models.
- It provides hydraulic system pressures and flows for lifting, tilting, and attachments for the different engine options.
- It details the mast lifting and lowering speeds for each model with various mast configurations.
- The last section describes the components of the steering system, including the hydraulic pump, flow control valve, steering control unit, and steering cylinder. It explains how hydraulic flow is controlled
Caterpillar cat 322 c excavator (prefix bkm) service repair manual (bkm00001 ...fujsefxdeksemm
This document provides instructions for removing and installing fuel system components on a Caterpillar 322C excavator with a 3126 engine. It describes removing and installing the fuel priming pump, primary fuel filter, fuel transfer pump, and fuel shutoff solenoid. Detailed steps and illustrations are provided for each procedure, and tools required are listed. Technicians are advised to keep components clean and contain fluids to prevent contamination.
Caterpillar cat 320 l track excavator (prefix 8lk) service repair manual (8lk...fujsefxdeksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. The procedure involves using several specialized tools to compress the valve springs so that the valve keepers can be removed and installed without removing the cylinder head. Air pressure is applied to the cylinder to hold the valves in position while the springs are worked on individually. Proper compression of the springs is important to avoid damaging the valve stems.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...fujsefxdeksemm
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It outlines the required tools and safety precautions, and gives step-by-step instructions to release pressure, remove hoses and bolts, and disassemble internal components like springs and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...fujsefxdeksemm
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...fujsefxdeksemm
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...fujsefxdeksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. It describes:
1) Removing the fuel injection lines, oil supply/drain lines, heat shield, and other components to access the pump housing.
2) Using various tools like bolts, washers, and pullers to remove the pump housing mounting bolts, nuts, and center bolt to detach the housing.
3) Lifting the housing off the engine using a sling and removing O-rings from the housing and governor.
4) Reversing the removal process to reinstall the housing, ensuring proper alignment and torque of mounting hardware.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)fujsefxdeksemm
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and gives step-by-step instructions to remove components like the rear housing, pinion drive, shift lever, brushes, and field winding coil. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualfujsefxdeksemm
This document provides instructions for disassembling and assembling starting motors for Caterpillar excavators. It describes the process for three starting motor models: 37-MT, 41-MT and 42-MT. The disassembly process involves removing components like the solenoid, rear housing, pinion drive housing, shift lever housing and field winding coil. The assembly process describes installing these components in reverse order while applying lubricants to bushings and torquing screws correctly.
The document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly that remove parts like the fuel ratio control, housing, springs, pins, seals, and more. It then lists 33 steps for assembly that install these parts in reverse order, noting to clean parts and apply oil before assembling. Tools like retaining ring pliers and drivers are required for some steps. Precise alignment and positioning of parts is emphasized during assembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for disassembling the piston motor of a 216B3 Skid Steer Loader. It outlines 25 steps to remove components such as nuts, valves, springs, pistons, seals, bearings, gears and more. Precautions are included to release spring forces safely. Required tools include retaining ring pliers, drivers, pullers and presses. Detailed illustrations accompany each step for clarity.
Case ih stx 380 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine systems, air induction systems, electrical systems, steering systems, and removal/installation of engines. It also lists recommended engine service manuals for different engine models used in the tractors.
Case ih steiger 535 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih steiger 430 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih puma 220 tier 4 b (final) tractor service repair manualfujsefxdeksemm
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 921 g wheel loader xr eh, new cab, tier 4b, multipurpose wheel loader se...fujsefxdeksemm
This document is a service manual that provides specifications and repair instructions for wheel loaders. It includes sections on the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, and electrical systems. The introduction provides safety information for working on the machine. The manual contains detailed part numbers, diagrams, and troubleshooting steps for maintenance and repairs.
Case 921 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document is a service manual for a 921E wheel loader. It contains sections covering general information, engines, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment. Each section provides removal and installation instructions for components, specifications, troubleshooting information, and other repair details. The manual also includes torque specifications, fluid and lubricant information, and electrical and hydraulic schematic diagrams in the rear.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
Case 721 g xt eh, new cab tier2 wheel loader service repair manual [fnh0721...fujsefxdeksemm
This document provides specifications for the engines in CNH Industrial 621G and 721G wheel loaders, including:
- Engine idle speeds and maximum no load RPM ranges
- Torque converter and hydraulic stall speed ranges
- Recommended temperature ranges for torque converter oil and hydraulic oil
It also notes the engine configuration (4 or 5 speed transmission) and indicates applicable regions.
Case 721 f xt wheel loader service repair manualfujsefxdeksemm
The document provides service information for a wheel loader, including:
- An overview of engine specifications for different transmission configurations.
- Part numbers for the engine service manual in multiple languages.
- Instructions to remove the engine, which involve draining fluids, disconnecting hoses, and using straps to lift the hood and engine out.
Case 721 f tier 4 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a 721F wheel loader. The main steps include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting bolts. Safety precautions are described such as releasing pressure from hydraulic and brake systems. Key components removed are the radiator, hood, air intake components, exhaust, and belt cover. Proper lifting and support equipment is required.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Caterpillar cat 320 c ln excavator (prefix bea) service repair manual (bea000...fujsefxdeksemm
The document provides instructions for removing and disassembling the stick drift reduction valve on a 320C excavator. It outlines the required tools and safety precautions, and gives step-by-step instructions to release pressure, remove hoses and bolts, and disassemble internal components like springs and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems.
Caterpillar cat 320 c l excavator (prefix bbl) service repair manual (bbl0000...fujsefxdeksemm
This document provides installation instructions for auxiliary control valves on a 320C excavator. It describes:
1) Installing the F1 and F4 auxiliary control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Connecting pilot lines, electrical connectors, and tubes to complete the installation of the control valves.
3) Installing panels, filters, and covers to finish the assembly.
Caterpillar cat 320 c excavator (prefix bbl) service repair manual (bbl00001 ...fujsefxdeksemm
This document provides instructions for assembling the F4 auxiliary control valve on 320C excavator models. It lists the required tools and notes on cleanliness. The steps include installing O-rings, springs, and other components in the proper order and orientation. Finally, it states to install the F4 auxiliary control valve by referring to another document providing full installation instructions.
This document provides instructions for disassembling a piston pump. It lists 71 steps and the required tools. The pump is first removed from the vehicle. Then various components like fittings, springs, seals and plates are removed. Measurements are taken to aid reassembly. Pins, shafts, bearings and other internal parts are then removed from the housing. Detailed illustrations accompany each step. The process is repeated for both sides of the pump.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...fujsefxdeksemm
This document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B engine. It describes:
1) Removing the fuel injection lines, oil supply/drain lines, heat shield, and other components to access the pump housing.
2) Using various tools like bolts, washers, and pullers to remove the pump housing mounting bolts, nuts, and center bolt to detach the housing.
3) Lifting the housing off the engine using a sling and removing O-rings from the housing and governor.
4) Reversing the removal process to reinstall the housing, ensuring proper alignment and torque of mounting hardware.
Caterpillar cat 225 d excavator service repair manual (2sj00001 and up)fujsefxdeksemm
The document provides instructions for disassembling three types of starting motors - 37-MT, 41-MT, and 42-MT. It details the required tools and gives step-by-step instructions to remove components like the rear housing, pinion drive, shift lever, brushes, and field winding coil. Photos illustrate each step. Technicians are instructed to clean parts with mineral spirits and inspect for wear and damage before reassembly.
Caterpillar cat 225 b excavator (prefix 2zd) service repair manualfujsefxdeksemm
This document provides instructions for disassembling and assembling starting motors for Caterpillar excavators. It describes the process for three starting motor models: 37-MT, 41-MT and 42-MT. The disassembly process involves removing components like the solenoid, rear housing, pinion drive housing, shift lever housing and field winding coil. The assembly process describes installing these components in reverse order while applying lubricants to bushings and torquing screws correctly.
The document provides instructions for disassembling and assembling the governor of a 225 EXCAVATOR model. It lists 34 steps for disassembly that remove parts like the fuel ratio control, housing, springs, pins, seals, and more. It then lists 33 steps for assembly that install these parts in reverse order, noting to clean parts and apply oil before assembling. Tools like retaining ring pliers and drivers are required for some steps. Precise alignment and positioning of parts is emphasized during assembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for disassembling the piston motor of a 216B3 Skid Steer Loader. It outlines 25 steps to remove components such as nuts, valves, springs, pistons, seals, bearings, gears and more. Precautions are included to release spring forces safely. Required tools include retaining ring pliers, drivers, pullers and presses. Detailed illustrations accompany each step for clarity.
Case ih stx 380 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair, removal and installation procedures for various components. Key sections include engine systems, air induction systems, electrical systems, steering systems, and removal/installation of engines. It also lists recommended engine service manuals for different engine models used in the tractors.
Case ih steiger 535 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih steiger 430 tractor service repair manualfujsefxdeksemm
This document provides a master table of contents for a service manual covering STX and Steiger series tractors. It lists sections that will provide information on specifications, maintenance, repair procedures, systems descriptions, and troubleshooting for engines, transmissions, steering, brakes, hydraulics, electrical systems, and other components. The sections listed cover a wide range of tractor models and provide references to additional manuals for specific engine repair information.
Case ih puma 220 tier 4 b (final) tractor service repair manualfujsefxdeksemm
This service manual provides information for servicing the Case IH PUMA® 185 CVT, PUMA® 185, PUMA® 200 CVT, PUMA® 200, PUMA® 220 CVT, PUMA® 220, and PUMA® 240 CVT tractors. The manual covers systems of the tractor such as the engine, transmission, axles, hydraulics, pneumatics, electrical systems, and more. Each system section includes detailed component information, diagrams, and specifications to aid technicians in maintenance and repair of the tractors.
Case 921 g wheel loader xr eh, new cab, tier 4b, multipurpose wheel loader se...fujsefxdeksemm
This document is a service manual that provides specifications and repair instructions for wheel loaders. It includes sections on the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, and electrical systems. The introduction provides safety information for working on the machine. The manual contains detailed part numbers, diagrams, and troubleshooting steps for maintenance and repairs.
Case 921 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document is a service manual for a 921E wheel loader. It contains sections covering general information, engines, fuel system, electrical systems, steering, power train, brakes, hydraulics, and mounted equipment. Each section provides removal and installation instructions for components, specifications, troubleshooting information, and other repair details. The manual also includes torque specifications, fluid and lubricant information, and electrical and hydraulic schematic diagrams in the rear.
Case 821 e tier 3 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a wheel loader. It is a service manual that outlines 36 steps for disconnecting all wiring, hoses, lines, and mounts to separate the engine from the rest of the machine. Key steps include draining fluids, removing the hood and attached components, disconnecting intake/exhaust components, drive belts, wiring harnesses, and finally fuel lines to fully separate the engine.
Case 721 g xt eh, new cab tier2 wheel loader service repair manual [fnh0721...fujsefxdeksemm
This document provides specifications for the engines in CNH Industrial 621G and 721G wheel loaders, including:
- Engine idle speeds and maximum no load RPM ranges
- Torque converter and hydraulic stall speed ranges
- Recommended temperature ranges for torque converter oil and hydraulic oil
It also notes the engine configuration (4 or 5 speed transmission) and indicates applicable regions.
Case 721 f xt wheel loader service repair manualfujsefxdeksemm
The document provides service information for a wheel loader, including:
- An overview of engine specifications for different transmission configurations.
- Part numbers for the engine service manual in multiple languages.
- Instructions to remove the engine, which involve draining fluids, disconnecting hoses, and using straps to lift the hood and engine out.
Case 721 f tier 4 wheel loader service repair manualfujsefxdeksemm
This document provides instructions for removing the engine from a 721F wheel loader. The main steps include draining fluids, disconnecting wiring harnesses and hoses, and removing mounting bolts. Safety precautions are described such as releasing pressure from hydraulic and brake systems. Key components removed are the radiator, hood, air intake components, exhaust, and belt cover. Proper lifting and support equipment is required.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. 15 - Engine
09 - Bedplate
00 - General
15 - 35 9823/0300-1 15 - 35
00 - General
Introduction .................................................... 15-35
Remove and Install ....................................... 15-36
Introduction
The bedplate acts as the main strength component
of the engine. it maintains the correct alignment and
supports the weight of the internal components.
Figure 154.
1
2
1 Bedplate
2 Crankcase
3. 15 - Engine
09 - Bedplate
00 - General
15 - 36 9823/0300-1 15 - 36
Remove and Install
Consumables
Description Part No. Size
Cleaner/Degreaser
- General purpose
solvent based parts
cleaner
4104/1557 0.4L
CAUTION This component is heavy. It must only
be removed or handled using a suitable lifting
method and device.
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Remove the drive belt.
Refer to: PIL 15-18-03.
5. Remove the oil sump.
Refer to: PIL 15-45-00.
6. Remove the turbocharger(if installed).
7. Remove the exhaust manifold.
Refer to: PIL 18-24-04.
8. Remove the starter motor.
Refer to: PIL 15-75-00.
9. Remove the flywheel housing.
Refer to: PIL 15-54-03.
10. Remove the crankshaft rear oil seal flange.
Refer to: PIL 15-12-09.
11. Remove the EGR (Exhaust Gas Recirculation) (if
installed).
12. Remove the inlet manifold.
Refer to: PIL 18-24-03.
13. Disconnect and remove the high and low
pressure fuel pipes.
Refer to: PIL 18-96-00.
14. Remove the timing gear front case.
Refer to: PIL 15-51-21.
15. Remove the fuel injection pump.
Refer to: PIL 18-18-15.
16. Remove the fuel injection drive gear.
Refer to: PIL 15-51-00.
17. Remove the intermediate drive gear.
Refer to: PIL 15-51-00.
18. Remove the high duty PTO (Power Take-Off)
device (if installed).
19. Remove the fuel injectors.
Refer to: PIL 18-18-03.
20. Remove the rocker cover.
Refer to: PIL 15-42-06.
21. Remove the rocker assembly including the push
rods
Refer to: PIL 15-42-00.
22. It is not necessary to remove the cylinder head
assembly to remove the bedplate. If however,
the cylinder head needs to be removed for other
reasons (for piston and connecting rod removal
for example) remove it now.
Refer to: PIL 15-06-00.
23. Position the engine upside down in a suitable jig
or fixture, supported at the front of the crankcase.
Remove
1. Remove the main bearing bolts in the sequence
shown.
Figure 155.
B
A
A Bedplate
B Main bearing bolts (x10)
2. Remove the bedplate peripheral bolts in the
sequence shown.
4. 15 - Engine
09 - Bedplate
00 - General
15 - 37 9823/0300-1 15 - 37
Figure 156.
C
C Peripheral bolts (x17)
3. Carefully separate the bedplate from the
crankcase. Use suitable lifting equipment (if the
bedplate is lifted manually, two people will be
required). Do not use a lever to separate the
bedplate.
4. Carefully remove the lower bearing shells from
the bedplate.
Figure 157.
A
D
A Bedplate
D Lower bearing shells (x5)
Before Installation
1. Clean off all traces of the old sealant compound
from the crankcase and bedplate mating faces.
2. Use a suitable degreasing agent to carefully
clean the main bearing saddles in the bedplate
and crankcase. Take care not to block the oil
ways or the piston cooling jets.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
Important: Anaerobic sealant will not start to cure
whilst it is open to the atmosphere, however when
air is excluded (for instance when the two parts are
put together) it will immediately start to harden. Make
sure that all the necessary tools, bolts etc. are readily
available prior to assembling the components. The
parts must be installed and tightened to the correct
torque value within 5min minutes (with a maximum
permissible time of 15min).
Important: Before installing the bedplate: Do not
rotate the crankshaft. Make sure that the upper main
bearing shells are flush with the bottom face of the
crankcase.
Install
Important: The crankshaft half bearings are made of
special material. Therefore, they must be replaced
every time they are removed to prevent seizures.
The lower and upper crankshaft half bearings cannot
be replaced singularly, and both halves must be
replaced together.
1. Make sure that all items are clean and free from
damage and corrosion.
2. Use a suitable degreasing agent to clean both
sides of the lower bearing shells.
Consumable: Cleaner/Degreaser - General
purpose solvent based parts cleaner
3. Install the lower bearing shells into the bedplate.
Make sure that the reference notches are at the
correct location.
Figure 158.
E
D
A
A Bedplate
D Lower bearing shells (x5)
E Reference notch
4. Lubricate the lower bearing shells with clean
engine oil.
5. Install the two shoulder half-rings onto the lower
crankcase. Apply two dots of ITP GX100 grease
to hold the rings in position.
5. 15 - Engine
09 - Bedplate
00 - General
15 - 38 9823/0300-1 15 - 38
Figure 159.
G
D
F
D Lower bearing shells (x5)
F Shoulder half-rings (x2)
G Guide pins
6. Apply a 1.0mm (0.04in) thick bead of Loctite 5188
around the crankcase/bedplate mating face as
shown.
Figure 160.
L
K
J
H
H Crankcase
J Loctite 5188
K Oil feed holes
L Return oil grooves
7. Make sure that you do not block the oil feed holes
and the return oil grooves.
8. Assemble the bedplate to the crankcase. Make
sure that the guide pins on the crankcase are
engaged properly in the slots on the bedplate.
9. Note: The bedplate is heavy. Two people will be
required to lift and rotate the bedplate safely on
to the crankcase.
10. Install the main bearing bolts (x10).
11. Tighten the bolts to the correct torque value in
three stages. Strictly follow the torque sequence
shown.
Figure 161.
B
A
12. Install the bedplate peripheral bolts (x17).
13. Tighten the bolts to the correct torque value in
two stages. Strictly follow the torque sequence
shown.
Figure 162.
C
Important: If the parts have not been tightened to the
correct torque value within the maximum 15min time
period, then the parts must be separated, thoroughly
cleaned and fresh sealant should be applied.
After Installation
1. Check that the crankshaft can be freely rotated
by hand.
2. Measure the crankshaft end float. Make sure that
the end float is between 0.18mm (0.007in) and
0.38mm (0.015in).
3. Carry out the procedures listed in the 'Before
Removal' section in reverse order.
6. 15 - Engine
09 - Bedplate
00 - General
15 - 39 9823/0300-1 15 - 39
Table 63. Torque Values
Item Description Nm
B Main bearing bolts (x10) (1st
Stage)
40
B Main bearing bolts (x10) (2nd
Stage)
70
B Main bearing bolts (x10) (3rd
Stage)
120
C Peripheral bolts (x17) (4th
Stage)
20
C Peripheral bolts (x17) (5th
Stage)
35
7. 15 - Engine
12 - Crankshaft
00 - General
15 - 42 9823/0300-1 15 - 42
Technical Data
Table 64.
Main bearing journal di-
ameter (x4)
- min 63.981mm (2.5189in)
- max 64.00mm (2.5196in)
Connecting rod bearing
journal diameter
- min 54.035mm (2.1274in)
- max 54.066mm (2.1286in)
Maximum wear and
ovality on journals
(1)
Crankshaft end float
- min 0.18mm ( 0.0070in)
- max 0.38mm ( 0.0149in)
(1) No visible damage/wear or marks
Component Identification
Figure 164.
B
A
A Crankcase
B Crankshaft
8. 15 - Engine
12 - Crankshaft
00 - General
15 - 43 9823/0300-1 15 - 43
Operation
Lubrication
Oil is fed from the main gallery via five drillings, one
to each of the main bearings. A groove around the
diameter of the upper main bearing shell allows oil
transfer to cross drillings in the crankshaft to feed
each of the big end bearings. Crankshaft gear is
'splash' lubricated. Front and rear crankshaft oil seals
prevent oil leakage from, and dirt ingress to, the
engine.
Figure 165.
1 Main gallery 2 Drillings (x5)
3 Main bearings 4 Big end bearings
5 Cross drillings 6 Crankshaft gear
7 Crankshaft oil seal 8 Crankshaft oil seal
9. 15 - Engine
12 - Crankshaft
00 - General
15 - 44 9823/0300-1 15 - 44
Check (Condition)
1. Check the main bearing surfaces for damage and
excessive wear.
2. Measure the crankshaft diameters to confirm
they are within service limits.
Refer to: PIL 15-12-00.
3. Check that the oilway cross drillings in the
crankshaft are clear and free from debris.
Blocked or restricted oilways will cause oil
starvation at the big end bearings.
4. Check that the piston cooling oil sprayers are
clear (if installed). If the sprayers cannot be
cleared remove the fixing screws. Remove the
sprayers and discard them.
Figure 166.
D
C
A
B
E
A Crankshaft B Shoulder half-rings
C Oil spray jets (if installed) D Fixing screws
E Main bearing shells
10. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 45 9823/0300-1 15 - 45
03 - Main Bearing
Introduction .................................................... 15-45
Check (Condition) .......................................... 15-46
Remove and Install ....................................... 15-46
Introduction
In a piston engine, the main bearings are the
bearings on which the crankshaft rotates.
The bearings hold the crankshaft in place and
prevent the forces created by the piston and
transmitted to the crankshaft by the connecting rods
from dislodging the crankshaft, instead forcing the
crank to convert the reciprocating movement into
rotation.
Figure 167.
A
B
A Main bearing
B Crankshaft
11. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 46 9823/0300-1 15 - 46
Check (Condition)
1. Check the bearing shell surfaces for signs of
damage and excessive wear.
2. Measure the crank pin diameters to confirm they
are within service limits.
Refer to: PIL 15-33-00.
3. Measure the bearing journal diameters to confirm
they are within service limits.
Refer to: PIL 15-12-00.
4. Replace any parts that are worn or not within the
specified tolerances.
Remove and Install
Special Tools
Description Part No. Qty.
Torque Wrench
(10-100Nm)
993/70111 1
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Remove the fuel injectors.
Refer to: PIL 18-18-03.
5. Remove the rocker cover.
Refer to: PIL 15-42-06.
6. Drain the oil from the engine.
Refer to: PIL 15-00-00.
7. Remove the oil sump.
Refer to: PIL 15-45-00.
8. Position the engine upside down in a suitable jig
or fixture, supported at the front of the crankcase.
Important: The connecting rod and the main bearing
cap have been fracture split and must be kept
together as a set. Utmost care must be taken to avoid
contamination and or damage to the fracture split
surfaces.
12. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 47 9823/0300-1 15 - 47
Remove
Figure 168.
4
3
Z
1
2
6
5
1 Piston rings
2 Piston
3 Connecting rod
4 Main bearing cap
5 Bolts
6 Big end bearing shells
Z Fracture split surfaces
1. It is recommended that the main bearing caps are
removed in pairs according to the firing cycle.
1.1. Cylinder 2
1.2. Cylinders 1 and 3
2. Put marks on the main bearing caps to make sure
that they are installed in their original positions
on assembly.
3. Rotate the crankshaft so that the main bearing
caps on cylinder 2 are positioned at the top.
4. Remove the bolts and lift off the main bearing
caps from the connecting rods.
5. Make sure that the bolts are not used again.
Discard the bolts.
Figure 169.
X
1 2
1 Main bearing caps
2 Main bearing cap bolts
6. Remove the bearing shells.
6.1. Lift out the bearing shells from the main
bearing caps.
6.2. Carefully rotate the crank to disengage from
the connecting rods and gain access to the
upper bearing shells.
6.3. Lift out the upper bearing shells.
6.4. The bearing shells must be replaced every
time they are removed.
7. Carefully rotate the crankshaft to position the
main bearing caps of cylinders 1 and 3.
8. Make sure that the crankshaft does not hit the
connecting rod of cylinder 2.
9. Do the steps 4 to 6 to remove the bearing caps
and bearing shells for cylinders 1 and 3.
10. Inspect the main bearings for signs of damage
and excessive wear.
Refer to: PIL 15-12-03.
Install
1. Replacement is the reversal of the removal
procedure.
2. Make sure that all items are clean and free from
damage and corrosion.
13. 15 - Engine
12 - Crankshaft
03 - Main Bearing
15 - 48 9823/0300-1 15 - 48
3. Install the upper bearing shell to the connecting
rod. Lubricate the bearing shell with clean engine
oil.
4. Install the lower bearing shell to the main bearing
cap. Lubricate the bearing shell with clean engine
oil.
5. Use compressed air to clean the fracture
surfaces of the main bearing caps before
assembly.
6. Install the main bearing cap to the connecting
rod.
7. Replace the fixing bolts.
8. Tighten the new bolts in two stages to the correct
torque value.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
9. Make sure that the crankshaft rotates smoothly
and the connecting rods have axial play.
10. After you perform the check, rotate the
crankshaft to position the first cylinder at TDC
(Top Dead Centre).
After Installation
1. Install the oil sump.
Refer to: PIL 15-45-00.
2. Install the rocker cover.
Refer to: PIL 15-42-06.
3. Install the fuel injectors.
Refer to: PIL 18-18-03.
4. Fill the engine with engine oil.
Refer to: PIL 15-00-00.
Table 65. Torque Values
Item Description Nm
2 1st Stage 40
2 2nd Stage 85
14. 15 - Engine
12 - Crankshaft
06 - Front Oil Seal
15 - 49 9823/0300-1 15 - 49
06 - Front Oil Seal
Remove and Install
Special Tools
Description Part No. Qty.
Crankshaft Front Oil
Seal Installation Tool
892/01157 1
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Remove the drive belt, refer to (PIL 15-18).
5. Remove the crankshaft pulley, refer to (PIL
15-12-12).
Remove
1. Use a suitable lever behind the lip of the
seal, carefully prise out the oil seal from the
counterbore in the crankcase. Take care not
to scratch or damage the counterbore or the
crankshaft hub. Damaged or dirty sealing faces
will cause the oil seal to fail.
Figure 170.
C
A
B
A Crankshaft oil seal
B Crankcase
C Crankshaft hub
Install
1. Make sure that the counterbore and the
crankshaft hub are clean and free from damage
and corrosion. Use a suitable degreasing agent
to clean all traces of oil and grease from the
counterbore. Important: The oil seal has a special
coating and MUST be installed dry without
lubricant.
2. Dismantle the seal installation tool. Bolt the
centre body to the crankshaft hub, using the
bolts. Refer to Figure 171.
Special Tool: Crankshaft Front Oil Seal
Installation Tool (Qty.: 1)
3. Install the oil seal on to the centre body. Make
sure that the seal is installed the correct way
around. Assemble the outer sleeve on to the
centre body and install the screw. Refer to Figure
171.
15. 15 - Engine
12 - Crankshaft
06 - Front Oil Seal
15 - 50 9823/0300-1 15 - 50
Figure 171.
F D
G
H
B
G
F
C
A
E
A Crankshaft oil seal B Crankcase
C Crankshaft hub D Seal installation tool
E Fixing bolts (x3) F Centre body
G Outer sleeve H Screw
4. Turn the screw to push the seal squarely into
the counterbore until the outer sleeve comes
up against the front edge of the counterbore.
When correctly installed, the front face of the seal
should be flush with the edge of the counterbore
within the specified tolerance. Refer to Figure
172.
Dimension: -0.5 -0/+0.5mm
Figure 172.
B
G
F
C
A
A Crankshaft oil seal
B Crankcase
C Crankshaft hub
F Centre body
G Outer sleeve
5. Remove the seal installation tool.
16. 15 - Engine
12 - Crankshaft
06 - Front Oil Seal
15 - 51 9823/0300-1 15 - 51
After Installation
1. Install the crankshaft pulley, refer to (PIL
15-12-12).
2. Install the drive belt, refer to (PIL 15-18).
17. 15 - Engine
12 - Crankshaft
12 - Pulley
15 - 52 9823/0300-1 15 - 52
12 - Pulley
Remove and Install
Special Tools
Description Part No. Qty.
Torque Wrench
(10-100Nm)
993/70111 1
Before Removal
1. This procedure requires service parts. Make
sure you have obtained the correct service parts
before you start, refer to Parts Catalogue.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the engine.
4. Remove the drive belt. Refer to (PIL 15-18).
Remove
1. Remove the fixing bolts and withdraw the pulley
from the crankshaft.
Figure 173.
A
B
A
A Crankshaft pulley
B Fixing bolts (x3)
2. The bolts must not be reused. Discard the bolts.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
steps.
2. Make sure that all items are clean and free from
damage and corrosion.
3. Renew the fixing bolts. Tighten the new bolts in
three stages to the correct torque value.
Special Tool: Torque Wrench (10-100Nm) (Qty.:
1)
4. The bolts are tightened using a torque and
angle method. Refer to Fasteners and Fixings,
General, Introduction (PIL 72-00).
Figure 174.
C
C Angle gauge (obtain locally)
After Replacement
1. Install the drive belt. Refer to (PIL 15-18).
Table 66.
Item Torque Value
(Nm)
Torque Angle
(Degrees)
2 (1st stage) 30N·m
2 (2nd stage) 75N·m
2 (Final stage) 180°
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 15 - Engine
12 - Crankshaft
15 - Phonic Wheel
15 - 53 9823/0300-1 15 - 53
15 - Phonic Wheel
Introduction
The crankshaft position sensor is installed on the
timing gear case. The sensor reads the signal from
the phonic wheel that is installed on the engine
pulley. The sensor sends an analogue signal to the
ECM (Engine Control Module). The sensor produces
a 5V square wave signal with Hall effect when the
motor is rotating. This data, together with the signal
from the sensor, allows the ECM to control the fuel
injection with respect to the TDC (Top Dead Centre)
of the piston.
For gap adjustment. Refer to: PIL 15-84-00.
20. 15 - Engine
18 - Engine Belt
21 - Tensioner
15 - 63 9823/0300-1 15 - 63
21 - Tensioner
Remove and Install
This procedure is applicable for machines installed
with Poly-V drive belt.
Important: The drive belt must always be replaced
every time it is removed, even if it has not reached
the scheduled hours for replacement.
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Remove the drive belt.
Refer to: PIL 15-18-03.
3. Remove the tensioning screw.
4. Remove the screw that secures the tightening
pulley.
5. Remove the tightening pulley.
Figure 178.
A
B
C
A Tensioning screw
B Screw
C Tightening pulley
Install
1. Insert the screw in the tightening pulley.
2. Manually tighten the screw on to the pulley pin up
to the stop; Loosen the screw again by one turn.
3. The screw must be out by the specified distance
from the surface of the tightening pulley.
Distance: 32mm
4. Install the drive belt.
Refer to: PIL 15-18-03.
5. Install the tightening screw on to the plate, up to
the stop on the pulley pin.
6. Tension the drive belt.
Figure 179.
A
B
E
D
C
A Tensioning screw
B Screw
C Tightening pulley
D Pulley pin
E 32mm