This service manual provides instructions for servicing Fastrac agricultural tractors models 4160, 4190, and 4220. The section on the engine timing gear provides the following information:
- An overview of the timing gear components and operation, including identification of narrow, broad with light duty PTO, and broad with heavy duty PTO gear configurations.
- Technical specifications for the timing gears, including tooth backlash tolerances and timing mark positions.
- Procedures for removing and installing the crankshaft gear, camshaft gear, and front timing gear case. This includes using specialty tools like pullers and applying sealant.
- Emphasis is placed on correctly aligning timing marks
Jcb tm220 telescopic wheeled loader service repair manual sn from 2679851 to ...fujsjefjwerkskemm
This service manual provides instructions for servicing the rocker and fittings on the TM180 and TM220 loader engines. The document describes how to remove and install the rocker assembly, disassemble and assemble the rocker arms, and remove and install the rocker cover. Technical specifications are also provided for rocker shaft dimensions, tappet clearances, and tappet dimensions. The operation of the hydraulic tappets is explained, along with difficult operating conditions that could cause play.
Jcb 4160 fastrac service repair manual sn from 2184000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the timing gears of Fastrac agricultural tractors models 4160, 4190, and 4220. The summary includes:
- The timing gears are located inside a case at the flywheel end of the engine and ensure the camshaft operates the valves at the correct times relative to the crankshaft.
- There are three main types of timing gear assemblies: narrow without power take-off, broad with light duty power take-off, and broad with heavy duty power take-off.
- Timing gear removal and installation procedures are provided, including removing the front cover, idler gear, and timing gear case. Cleaning and applying sealant is
Jcb js200 excavator service repair manual sn 1783500 and upfisjejfskemmd
This document is a service manual that provides instructions for servicing excavator engines. It contains sections on general information, components, operation, adjustment, removal and installation of valves. The summary focuses on valves:
The manual contains information on servicing excavator engine valves, including identifying components, measuring clearances, adjusting clearances, and removing and installing valves. Proper valve clearance is important for correct timing in relation to piston movement. Clearances should be measured when the engine is cold and adjusted if outside specifications.
JCB JS160W WHEELED EXCAVATOR Service Repair Manual SN:2584081fujdfjjskekmwem
This service manual provides instructions for servicing wheeled excavators including models JS145W, JS160W, and JS20 MH. The manual contains sections covering the entire machine systems from the engine, brakes, and hydraulics to the operator station, electrical system, and attachments. Specific chapters provide procedures for maintenance, removal and installation of components, including the flywheel, oil pump, engine mounts, and oil cooler. Safety warnings are included throughout and technical illustrations supplement the text.
This document contains technical specifications and emissions data for various JCB excavator models. It includes sections on noise emissions, vibration emissions, and fluids/lubricants specifications. Tables of data provide the A-weighted sound pressure and power levels, whole-body vibration values, and fluid capacities for different models. Guidelines are given for minimizing operator exposure to noise and vibration.
Jcb 3 cx backhoe loader service repair manual sn from 2442701 to 2451000fusefjskekkmem
This service manual section provides information on servicing the crankshaft and related components on a backhoe loader. It includes identification of parts, technical specifications, operation descriptions, removal and installation instructions, and check/inspection procedures. Proper cleaning and installation of the crankshaft oil seal is critical to prevent oil leakage. Removal and installation of the crankshaft requires carefully following all steps while ensuring components remain clean and undamaged.
Jcb 3 cx t2 t3 backhoe loader service repair manual from 2615002 to 2616002fusefjjskekemm
This service manual provides instructions for servicing the valves on a backhoe loader engine. It describes how the valve train components operate and the process for measuring and adjusting valve clearances. The procedure involves using special tools to position the engine, lock the valve tappets, and measure clearance with a dial indicator. Clearances are adjusted by turning the tappet adjusters if needed. Instructions are also provided for removing and installing the valves, which requires compressing the springs and removing retaining collets.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
Jcb tm220 telescopic wheeled loader service repair manual sn from 2679851 to ...fujsjefjwerkskemm
This service manual provides instructions for servicing the rocker and fittings on the TM180 and TM220 loader engines. The document describes how to remove and install the rocker assembly, disassemble and assemble the rocker arms, and remove and install the rocker cover. Technical specifications are also provided for rocker shaft dimensions, tappet clearances, and tappet dimensions. The operation of the hydraulic tappets is explained, along with difficult operating conditions that could cause play.
Jcb 4160 fastrac service repair manual sn from 2184000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the timing gears of Fastrac agricultural tractors models 4160, 4190, and 4220. The summary includes:
- The timing gears are located inside a case at the flywheel end of the engine and ensure the camshaft operates the valves at the correct times relative to the crankshaft.
- There are three main types of timing gear assemblies: narrow without power take-off, broad with light duty power take-off, and broad with heavy duty power take-off.
- Timing gear removal and installation procedures are provided, including removing the front cover, idler gear, and timing gear case. Cleaning and applying sealant is
Jcb js200 excavator service repair manual sn 1783500 and upfisjejfskemmd
This document is a service manual that provides instructions for servicing excavator engines. It contains sections on general information, components, operation, adjustment, removal and installation of valves. The summary focuses on valves:
The manual contains information on servicing excavator engine valves, including identifying components, measuring clearances, adjusting clearances, and removing and installing valves. Proper valve clearance is important for correct timing in relation to piston movement. Clearances should be measured when the engine is cold and adjusted if outside specifications.
JCB JS160W WHEELED EXCAVATOR Service Repair Manual SN:2584081fujdfjjskekmwem
This service manual provides instructions for servicing wheeled excavators including models JS145W, JS160W, and JS20 MH. The manual contains sections covering the entire machine systems from the engine, brakes, and hydraulics to the operator station, electrical system, and attachments. Specific chapters provide procedures for maintenance, removal and installation of components, including the flywheel, oil pump, engine mounts, and oil cooler. Safety warnings are included throughout and technical illustrations supplement the text.
This document contains technical specifications and emissions data for various JCB excavator models. It includes sections on noise emissions, vibration emissions, and fluids/lubricants specifications. Tables of data provide the A-weighted sound pressure and power levels, whole-body vibration values, and fluid capacities for different models. Guidelines are given for minimizing operator exposure to noise and vibration.
Jcb 3 cx backhoe loader service repair manual sn from 2442701 to 2451000fusefjskekkmem
This service manual section provides information on servicing the crankshaft and related components on a backhoe loader. It includes identification of parts, technical specifications, operation descriptions, removal and installation instructions, and check/inspection procedures. Proper cleaning and installation of the crankshaft oil seal is critical to prevent oil leakage. Removal and installation of the crankshaft requires carefully following all steps while ensuring components remain clean and undamaged.
Jcb 3 cx t2 t3 backhoe loader service repair manual from 2615002 to 2616002fusefjjskekemm
This service manual provides instructions for servicing the valves on a backhoe loader engine. It describes how the valve train components operate and the process for measuring and adjusting valve clearances. The procedure involves using special tools to position the engine, lock the valve tappets, and measure clearance with a dial indicator. Clearances are adjusted by turning the tappet adjusters if needed. Instructions are also provided for removing and installing the valves, which requires compressing the springs and removing retaining collets.
Jcb 550 140 telescopic handler service repair manual sn from 2902000 onwardsfisjejfskemmd
This service manual provides instructions for servicing the loadall rough terrain variable reach truck. It contains sections on the machine systems including the engine, fuel system, cooling system, brake system, hydraulic system and electrical system. The section summarized focuses on servicing the engine valves and connecting rod big-end bearings. It provides removal and installation instructions, component identification diagrams, and technical specifications for the valves and instructions to check the big-end bearings for wear. Safety information is also provided to ensure the work is performed correctly.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb 509 42 telescopic handler service repair manual sn from 1402020 and upfdjjsekksemxs
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks with model numbers 506-36, 507-42, 509-42, 510-56, and 512-56. The manual contains sections covering the machine components, including the engine, brake system, hydraulic system, electrical system, and driveline. The section summarized provides instructions for removing and installing the front and rear cases of the semi-automatic gearbox. The process requires using various special tools and consumables, checking clutch shaft end floats, and applying sealants and threadlocker to fasteners.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
The document is a parts catalog for a wheel loader model 95Z7B powered by an Isuzu 6WG1 engine. It lists various equipment components and parts, including pumps, motors, valves, cylinders, and parts of the power train like the transmission and axles. The parts are organized by component type and listed with part numbers, names, quantities, and other identifying information.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb jcb305, js305 excavator service repair manual (from 2452101 to 2452200)fjjsjeusekkekm
This document is a service manual for an excavator model JCB305, JS305. It contains instructions for servicing and repairing components of the excavator, listed by system (e.g. engine, hydraulic system, electrical system). The manual provides technical specifications, diagrams, removal and installation instructions, and checking/inspection procedures for parts like the engine, pistons, connecting rods, and more. Safety warnings are included to treat the manual as part of the machine and follow all instructions to avoid injury during operation and maintenance.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Liebherr r974 c 1057 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r974 c 1417 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r974 c 1365 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r954 c 1698 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r954 c 1615 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r926 1345 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and updated by Liebherr's technical documentation department.
Liebherr r926 1023 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r926 1022 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r916 1306 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r914 c 1063 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for repairs and maintenance.
2. Safety instructions and warnings for working on the equipment are marked with symbols for danger and caution.
3. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training courses. Site-specific operating instructions and spare parts documentation are separate.
Liebherr r914 c 1062 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for repairs and maintenance.
2. Safety instructions and warnings for working on the equipment are marked with symbols for danger and caution.
3. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training courses. Site-specific operating instructions and spare parts documents are separate.
Liebherr r906 1366 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the various systems of the excavator such as the engine, hydraulics, electrical systems, and more. The manual is broken down into sections for each subsystem and also covers options and cab components.
Liebherr r906 1144 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the machine's major systems and components including the engine, hydraulics, electrical systems, and more. Symbols are used to indicate dangers and important notes. The manual is intended to help maintain the excavators and ensure their long life.
Liebherr r906 1143 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the machine's major systems and components including the engine, hydraulics, electrical systems, and more. Symbols are used to indicate hazards and required actions. The manual is intended to help users properly service and maintain the excavators.
Liebherr r906 1142 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the various systems of the excavator and provides maintenance guidelines for components like the engine, hydraulics, electrical systems, and more. Symbols are used throughout to identify safety hazards and notes. The manual is intended to help users properly service and maintain Liebherr excavators.
Jcb 135 hd skid steer loader service repair manual (sn 2431601 and up)fiskefjskemem
This service manual provides instructions for servicing a JCB 135 HD and 155 HD skid steer loader. It contains sections covering the machine systems, including the engine, fuel system, hydraulic system, electrical system, and other components. The document provides detailed descriptions of components, operating principles, maintenance and repair procedures, specifications, and safety information. Technicians are instructed to carefully follow the procedures in the manual to properly service the machine.
Jcb 509 42 telescopic handler service repair manual sn from 1402020 and upfdjjsekksemxs
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks with model numbers 506-36, 507-42, 509-42, 510-56, and 512-56. The manual contains sections covering the machine components, including the engine, brake system, hydraulic system, electrical system, and driveline. The section summarized provides instructions for removing and installing the front and rear cases of the semi-automatic gearbox. The process requires using various special tools and consumables, checking clutch shaft end floats, and applying sealants and threadlocker to fasteners.
Jcb js220 tracked excavator service repair manual sn from 2460501 onwardsfusjefjkskem
This service manual provides information on servicing excavator models JS200, JS210, JS220, and JS235. It contains instructions from the manufacturer and copyrighted content. The manual covers safety procedures and contains sections on various machine systems including the engine, fuel system, cooling system, driveline, hydraulics, electrical system and other components.
The document is a parts catalog for a wheel loader model 95Z7B powered by an Isuzu 6WG1 engine. It lists various equipment components and parts, including pumps, motors, valves, cylinders, and parts of the power train like the transmission and axles. The parts are organized by component type and listed with part numbers, names, quantities, and other identifying information.
Jcb 325 t skid steer loader service repair manual sn from 2476302 to 2477300fujsjefjskekmem
This service manual provides instructions for servicing JCB skid steer loaders and their components. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics and electrical system. The section summarized here provides instructions for removing and installing the crankshaft from the engine. It describes cleaning and inspecting the crankshaft, lists the required tools and consumables, and outlines the step-by-step removal and installation procedures. Precautions are given such as allowing the engine to cool before working on it and using lifting devices due to the heavy weight of components.
Jcb jcb305, js305 excavator service repair manual (from 2452101 to 2452200)fjjsjeusekkekm
This document is a service manual for an excavator model JCB305, JS305. It contains instructions for servicing and repairing components of the excavator, listed by system (e.g. engine, hydraulic system, electrical system). The manual provides technical specifications, diagrams, removal and installation instructions, and checking/inspection procedures for parts like the engine, pistons, connecting rods, and more. Safety warnings are included to treat the manual as part of the machine and follow all instructions to avoid injury during operation and maintenance.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Liebherr r974 c 1057 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r974 c 1417 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r974 c 1365 hydraulic excavator service repair manualkfmsiekdodk
The document is a service manual that provides technical information for maintenance and repair of Liebherr hydraulic excavators. It contains sections on the engine, hydraulic and electrical systems, undercarriage, and other components. Symbols are used to indicate dangers, warnings, and important notes. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training.
Liebherr r954 c 1698 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r954 c 1615 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that provides technical specifications and maintenance instructions. It contains sections on general information, tools, technical data, the engine, hydraulic and electrical systems, undercarriage components, and other optional equipment. The manual is intended to assist customer support and maintenance personnel but does not replace proper training. Safety symbols are defined and safety instructions provided throughout to warn technicians of dangers.
Liebherr r926 1345 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and updated by Liebherr's technical documentation department.
Liebherr r926 1023 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r926 1022 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r916 1306 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r914 c 1063 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for repairs and maintenance.
2. Safety instructions and warnings for working on the equipment are marked with symbols for danger and caution.
3. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training courses. Site-specific operating instructions and spare parts documentation are separate.
Liebherr r914 c 1062 hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr excavators that contains:
1. Technical data, design descriptions, and service/setup instructions for repairs and maintenance.
2. Safety instructions and warnings for working on the equipment are marked with symbols for danger and caution.
3. The manual is intended to assist customer support and training, but does not replace proper technical qualifications or training courses. Site-specific operating instructions and spare parts documents are separate.
Liebherr r906 1366 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the various systems of the excavator such as the engine, hydraulics, electrical systems, and more. The manual is broken down into sections for each subsystem and also covers options and cab components.
Liebherr r906 1144 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the machine's major systems and components including the engine, hydraulics, electrical systems, and more. Symbols are used to indicate dangers and important notes. The manual is intended to help maintain the excavators and ensure their long life.
Liebherr r906 1143 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the machine's major systems and components including the engine, hydraulics, electrical systems, and more. Symbols are used to indicate hazards and required actions. The manual is intended to help users properly service and maintain the excavators.
Liebherr r906 1142 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the various systems of the excavator and provides maintenance guidelines for components like the engine, hydraulics, electrical systems, and more. Symbols are used throughout to identify safety hazards and notes. The manual is intended to help users properly service and maintain Liebherr excavators.
Liebherr d9508 a7 diesel engine service repair manualkfmsiekdodk
The document appears to be a service manual or technical document for diesel engines. It notes that the service manual is not subject to updates and recommends referring to any supplementary documents for the most up to date information. It also provides contact information for technical support and suggestions. The majority of the document contains technical diagrams and specifications related to diesel engine parts and maintenance procedures.
Liebherr lh120 c hydraulic excavator service repair manualkfmsiekdodk
This document contains adjustment protocols for the working pumps and pressure cut-off settings of an excavator model LH 120 M. It provides detailed instructions for technicians to check and adjust the beginning of regulation and pressure cut-off for each of the machine's four working pumps using variables in the Sculi program and by monitoring pressure readings. The protocols describe setting test currents, activating specific functions, and noting pressure values to ensure correct pump operation and pressure relief settings.
Liebherr r906 1285 advanced hydraulic excavator service repair manualkfmsiekdodk
This document is the service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is intended to assist support services and includes safety warnings. It describes the machine's major systems and components including the engine, hydraulics, electrical systems, and more. Symbols are used to indicate hazards and required actions. The manual is intended to help ensure safe and proper maintenance of Liebherr excavators.
Liebherr r916 1344 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Liebherr r926 1087 classic hydraulic excavator service repair manualkfmsiekdodk
This document is a service manual for Liebherr hydraulic excavators. It contains technical specifications and instructions for maintenance and repair. The manual is divided into sections covering the engine, hydraulic and electrical systems, swing mechanisms, tracks and other components. Safety symbols are introduced and procedures are marked for requirements, actions, and expected results. The manual is intended to assist technicians while not replacing proper training. It is produced and copyrighted by Liebherr.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. 15 - Engine
51 - Timing Gear
00 - General
15 - 143 9813/3600-3 15 - 143
00 - General
Introduction .................................................. 15-143
Technical Data ............................................. 15-145
Component Identification ............................. 15-145
Operation ..................................................... 15-146
Remove and Install ..................................... 15-147
Introduction
The timing gears are located inside a case at the
flywheel end of the engine.
The engine must be timed so that the camshaft
operates the valves at the correct times relative to
the crankshaft position.
The timing gear drives the camshaft, high pressure
pump and the oil pump. The timing gear train consists
of hardened, helically cut gear wheels. The gears are
housed by the timing gear case, which is installed to
the front of the engine.
The idler gear is supported with a ball bearing on the
shaft on the front face of the crankcase.
There are three main types of timing gear
assemblies:
• Narrow without PTO (Power Take-Off)
Figure 178. Narrow without PTO
A
C
B
D
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
• Broad with light duty PTO
3. 15 - Engine
51 - Timing Gear
00 - General
15 - 144 9813/3600-3 15 - 144
Figure 179. Broad with Light Duty PTO
A
E
C
B
D
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
E PTO gear
• Broad with heavy duty PTO
Figure 180. Broad with Heavy Duty PTO
A
E
C
B
D
F
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
E PTO gear
F Smaller idler gear
If the engine is equipped with light duty PTO,
hydraulic pump is driven through a gear or a separate
drive unit.
In engines with heavy duty PTO, hydraulic pump or
compressor is driven through a small idler gear.
4. 15 - Engine
51 - Timing Gear
00 - General
15 - 145 9813/3600-3 15 - 145
Technical Data
Table 53. Timing Gear Data
Description Data
Tooth backlash 0.05 –0.25 mm
Maximum permissible
side wobble of gears
0.05 mm
Idle gear Slide bearing and 50.7
mm shaft length
Table 54. Timing Marks
Description
(1)
Data
On crankshaft gear 2 dots on tooth
On high pressure pump
gear
1 dot on notch
On camshaft gear 1 dot on notch
On idler gear
Against crankshaft gear
mark
1 dot on tooth
Against camshaft gear
mark
1 dot on tooth
Against high pressure
pump mark
2 dots on notch
(1) Timing marks on the gears are in alignment
when the 1st cylinder piston is at its TDC (Top Dead
Centre) between compression and power strokes.
Component Identification
Figure 181. Narrow without PTO
A
C
B
D
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
Figure 182. Broad with Light Duty PTO
A
E
C
B
D
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
E PTO (Power Take-Off) gear
5. 15 - Engine
51 - Timing Gear
00 - General
15 - 146 9813/3600-3 15 - 146
Figure 183. Broad with Heavy Duty PTO
A
E
C
B
D
F
A Camshaft gear
B Idler gear
C High pressure pump gear
D Crankshaft gear
E PTO gear
F Smaller idler gear
Operation
All the gears are driven via the crankshaft gear as
follows:
• Camshaft gear-The camshaft is driven at half
crankshaft speed.
• High pressure fuel pump gear-The high
pressure fuel pump is driven via the camshaft
gear installed to the camshaft.
• Oil pump gear-The lubrication oil pump is driven
directly by the crankshaft gear.
• Power Take-Off (PTO)-driven by the crankshaft
gear via idler gear.
• Low Duty Power Take-Off (PTO) Gear (if
installed)-driven by the camshaft gear.
Timing
The engine must be `timed' so that the camshaft
operates the valves at the correct times relative to
the crankshaft position.
Valve timing is achieved by ensuring that the
camshaft drive gear is meshed to the crankshaft
gear at their correct angular positions.Refer to: PIL
15-00-00.
6. 15 - Engine
51 - Timing Gear
00 - General
15 - 147 9813/3600-3 15 - 147
Remove and Install
For removal and installation procedure of the timing
gear. Refer to: PIL 15-51-21.
7. 15 - Engine
51 - Timing Gear
03 - Crankshaft Gear
15 - 148 9813/3600-3 15 - 148
03 - Crankshaft Gear
Remove and Install
Remove
1. Get access to the crankshaft gear.
2. Apply the special puller (AGCO Part number
9052 48800) to the crankshaft gears.
Figure 184.
B
A
A Crankshaft gear
B Puller (AGCO Part number 9052 48800)
3. Pull off the crankshaft gears (x2).
4. Do not damage the crankshaft.
5. Clean the seat on the crankshaft with a wire
brush.
Install
1. Heat the new gears to specified temperature.
Temperature: 220 –250 °C ( 427.7 –481.6 °F)
2. Assemble the crankshaft gears onto the
crankshaft.
3. Make a note of the position of the key. Refer to
Figure 185.
4. Make sure that the aligning marks on the front
gear are visible.
5. Set the crankshaft key into the angular key slot.
Figure 185.
6. Allow the gears to cool.
8. 15 - Engine
51 - Timing Gear
06 - Camshaft Gear
15 - 149 9813/3600-3 15 - 149
06 - Camshaft Gear
Remove and Install
Refer to Camshaft- Remove and Install.Refer to: PIL
15-15-00.
9. 15 - Engine
51 - Timing Gear
21 - Front Case
15 - 150 9813/3600-3 15 - 150
21 - Front Case
Remove and Install
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Drain the engine oil.
Refer to: PIL 15-21-00.
3. Remove the oil sump.
Refer to: PIL 15-45-00.
4. Remove the radiator.
Refer to: PIL 21-03-00.
5. Remove the cooling fan.
6. Remove the alternator.
Refer to: PIL 15-72-00.
7. Remove the belt tensioner and the belt.
8. If installed, remove the HVAC (Heating
Ventilation Air Conditioning) unit.
Refer to: PIL 12-03-00.
9. Remove the coolant pump.
Refer to: PIL 21-09-00.
10. Remove the crankshaft belt pulley and the
vibration damper.
11. Loosen the crankshaft nut by two turns with
the specified spanner (AGCO Part number 9024
55800).
Figure 186.
A
A Spanner (AGCO Part number 9024 55800)
12. Remove the hub from the crankshaft with
the specified puller (AGCO Part number 9201
82390).
12.1. Do not remove the nut completely at this
stage. The hub can be thrown dangerously
when the nut is loosened.
Figure 187.
B
B Puller (AGCO Part number 9201 82390)
13. Remove the camshaft speed sensor, hydraulic
pump drive unit lubrication pipe and the drive
unit.
14. Remove the front cover.
15. Make a note that the screws on the idler gear
shaft and the screws on the broad timing gear
are similar. Do not interchange them.
10. 15 - Engine
51 - Timing Gear
21 - Front Case
15 - 151 9813/3600-3 15 - 151
Figure 188.
D
C
C Idler gear shaft
D Broad timing gear
16. If necessary, remove the oil deflector ring from
the front end of the crankshaft.
17. If necessary, remove the HP (High Pressure)
pump.
Refer to: PIL 18-18-15.
17.1. If you do not remove the HP pump,
disconnect all electrical harnesses and the
pipes from the HP pump.
18. Remove the idler gear screw.
19. Remove the idler gear.
20. Remove the small idler gear.
21. Remove the camshaft.
22. If the cylinder head and the rocker assembly
is not removed, prevent the tappets from falling
down.
Refer to: PIL 15-15-00.
23. Remove the screws from the timing gear case.
24. Remove the timing gear case.
Refer to: PIL 15-51-21.
25. Remove the crankshaft front sealing ring from the
front case.
26. Make a note that the oil deflector ring is behind
the sealing ring.
Install
1. Clean all the parts thoroughly.
2. Apply specified sealant (AGCO Part number
8366 62735) on the timing gear case sealing
surfaces.
3. Install the timing gear case against the
crankcase.
4. Install the tension pins with the specified drift
(AGCO Part number 9025 98700).
Figure 189.
E
E Tension pin
5. Tighten the nuts and the bolts.
6. Lubricate the camshaft bearings and insert the
camshaft into the crankcase.
7. Release the push rods and the tappets.
8. Install the idler gear stud.
9. Make sure that the timing marks are in the correct
position.
11. 15 - Engine
51 - Timing Gear
21 - Front Case
15 - 152 9813/3600-3 15 - 152
Figure 190.
F
G
F Timing marks
G Front cover screw holes
10. Rotate the idler gear shaft so that the front cover
screw holes are vertically aligned.
11. Install the bolts and the washers.
12. Tighten the bolts to the correct torque value.
Torque: 180 N·m
13. Install the small idler gear.
14. Apply the locking compound on the screws.
15. Tighten the screw to the correct torque value.
Torque: 45 N·m
16. Install the HP pump and the gear wheel.
17. Make sure that the timing marks are in the correct
position.
18. Tighten the camshaft and the HP pump gear nut.
19. Check the tooth backlash.
19.1. Make sure that the backlash is as
specified.
Dimension: 0.05 –0.25 mm
Figure 191.
H
H Feeler gauge
20. If removed, install the oil deflector ring on the
front of the crankshaft.
21. Install the front cover.
22. Install the drive unit cover and the shaft to the
front cover.
23. Apply the specified sealant (AGCO Part number
8366 62735) on the timing gear case.
24. Install the timing gear case front cover.
25. Install the tension pin in its place.
26. Make a note that the sealing ring is under the idler
gear screws.
27. Install the drive unit rear bearing and the adaptor
plate.
28. Install the nuts and the bolts.
29. Install the protective plate into the seal location.
30. Install the crankshaft front seal with a suitable
drift (AGCO Part number 9103 94600).
12. 15 - Engine
51 - Timing Gear
21 - Front Case
15 - 153 9813/3600-3 15 - 153
Figure 192.
J
J Drift (AGCO Part number 9103 94600)
31. Check the condition of the conical surfaces on
the crankshaft and the hub.
32. Lubricate the seals and the sealing surface.
33. Lubricate the hub nut thread, rear surface and
the outer surface with Vaseline.
33.1. Do not use oil, it may run into the conical
surfaces.
34. Install the crankshaft hub.
35. Install the hub nut onto the crankshaft thread.
36. Tighten the hub nut the correct torque value.
Torque: 1,000 ± 100 N·m
37. Install the crankshaft belt pulley and the vibration
damper.
38. Install the coolant pump.
Refer to: PIL 21-09-00.
39. If removed, install the HVAC unit.
Refer to: PIL 12-03-00.
40. Install the belt tensioner and the belt.
41. Install the alternator.
Refer to: PIL 15-72-00.
42. Install the cooling fan.
43. Install the radiator.
Refer to: PIL 21-03-00.
44. Install the oil sump.
Refer to: PIL 15-45-00.
45. Fill the engine oil to the correct level.
Refer to: PIL 15-21-00.
13. 15 - Engine
54 - Flywheel
00 - General
15 - 156 9813/3600-3 15 - 156
Technical Data
Table 55. Flywheel Data
Description Data
Interference fit between
ring gear and flywheel
0.425 –0.6 mm
Before installation of the
ring gear, heat up to a
temperature of
150 –200 °C ( 301.8 –
391.7 °F)
Flywheel unbalance Maximum 1.0 Ncm
Maximum permissible
axial wobble of flywheel
clutch face, measured at
inner edge of the clutch
face on diameter 200
mm
0.06 mm
Component Identification
Figure 193.
2
1
1 Flywheel
2 Flywheel gear ring
14. 15 - Engine
54 - Flywheel
00 - General
15 - 157 9813/3600-3 15 - 157
Remove and Install
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Make sure that the engine is safe to work on. If
the engine has been running, let it cool before
you start the service work.
3. Get access to the flywheel.
4. Remove the bolts and withdraw the flywheel from
the crankshaft hub.
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
step.
2. Clean the contact surfaces on the crankshaft rear
flange and on the flywheel.
3. Use suitable studs as a guide when you install
the flywheel on the crankshaft rear flange.
4. Tighten the bolts to the correct torque value.
Torque: 150 N·m
15. 15 - Engine
54 - Flywheel
03 - Housing
15 - 158 9813/3600-3 15 - 158
03 - Housing
Introduction .................................................. 15-158
Remove and Install ..................................... 15-159
Introduction
The flywheel housing is installed at the rear end of
the crankcase. The seal for the crankshaft rear end
is placed in a bore in the housing. The starter motor
fixing point is installed in the flywheel housing.
The lower face of the flywheel housing functions
as a sealing surface for the oil sump gasket. This
means that the lower face of the crankcase must
be level with the flywheel housing. When you install
the flywheel housing, its position is determined by
tension pins.
16. 15 - Engine
54 - Flywheel
03 - Housing
15 - 159 9813/3600-3 15 - 159
Remove and Install
Remove
1. This procedure requires service parts. Make sure
that you have obtained the correct service parts
before you start.
2. Remove the flywheel.
Refer to: PIL 15-54-00.
3. Remove the bolts from the flywheel housing.
4. Separate the flywheel housing from the gear
case.
Install
1. Clean the sealing surfaces between the
crankcase and the flywheel housing.
2. Apply silicone sealant to the flywheel housing.
Refer to Figure 194.
Figure 194.
A
A Silicon sealant
3. Keep the flywheel housing in place.
4. Install the bolts.
5. Centre the housing with ARCO centering tool
number 9052 46400.
5.1. This is important for engines with a turbine
clutch.
6. Install the tension pins with a suitable drift.
7. Apply thread sealant to the bolts that are in
contact with oil or water.
8. Tighten the bolts to the specified torque value.
8.1. For inner ring socket head bolts
Torque: 80 N·m
8.2. For outer ring hexagonal bolts
Torque: 150 N·m
17. 15 - Engine
54 - Flywheel
09 - Gear Ring
15 - 160 9813/3600-3 15 - 160
09 - Gear Ring
Introduction .................................................. 15-160
Remove and Install ..................................... 15-161
Introduction
The ring gear cannot be turned around because its
teeth are chamfered and hardened on the starter
motor side.
If the ring gear is worn, it must be replaced.
Figure 195.
18. 15 - Engine
54 - Flywheel
09 - Gear Ring
15 - 161 9813/3600-3 15 - 161
Remove and Install
Remove
1. Get access to the gear ring.
2. Tap the gear ring at various points with a drift.
3. Remove the gear ring from the flywheel.
Install
1. Clean the flywheel contact face with a steel wire
brush.
2. Warm the gear ring to the specified temperature.
Temperature: 150 –200 °C ( 301.8 –391.7 °F)
3. Install the gear ring with the inner diameter
chamfer turned against the flywheel and the teeth
chamfer against the starter motor.
4. Allow the gear ring to cool freely.
4.1. Do not use coolant.
19. 15 - Engine
60 - Oil Pump
00 - General
15 - 165 9813/3600-3 15 - 165
Remove and Install
Remove
1. Drain the engine oil.
Refer to: PIL 15-21-00.
2. Remove the oil sump.
Refer to: PIL 15-45-00.
3. Disconnect the oil pump suction pipe and the
pressure pipe.
4. Remove the oil pump.
5. Collect any shims between the pump and the
crankcase.
Install
1. Install the oil pump.
2. Check the tooth backlash against the crankshaft
gear.
2.1. Make sure that the clearance is within the
specified limits.
Dimension: 0.05 –0.25 mm
2.2. If necessary, adjust the shims between the
pump body and the crankcase.
Figure 196. Backlash Check
2.3. Use a shim of the specified thickness only
(AGCO Part number 8360 07871).
2.4. Make a note that one shim increases or
decreases the backlash by the specified
value.
Dimension: 0.07 mm
2.5. Make sure that when you measure the tooth
backlash, the engine is the correct way up
as the crankshaft bearing clearance affects
the tooth backlash.
3. Connect the oil pump suction pipe and the
pressure pipe.
4. Install the oil sump.
Refer to: PIL 15-45-00.
5. Fill the engine oil to the correct level.
Refer to: PIL 15-21-00.
Table 57. Torque Values
Item Description Nm
A Nut 60
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. 15 - Engine
60 - Oil Pump
00 - General
15 - 166 9813/3600-3 15 - 166
Disassemble and Assemble
Remove
1. Remove the oil pump.
Refer to: PIL 15-60-00.
2. Remove the pump cover.
3. Discard the gasket.
4. Remove the gear on the axle.
5. Hold the pump gear across the teeth in a soft jaw
vice.
6. Loosen the drive gear nut.
7. Hit the end of the shaft with a soft hammer and
remove the gear wheel.
8. Pull out the drive shaft gear wheel.
9. Clean all the parts thoroughly.
10. Check the condition of the pump components for
wear and other damage.
11. Replace the damaged parts.
12. Replace all the seals.
13. The bearing points are provided with separate
bearing bushes. If you replace the bushes,
machine them to the specified size after
installation.
Dimension: 18 –18.018 mm
Install
1. Install the gear wheels to the pump body.
2. Install the cover with a new gasket.
3. Tighten the screws partially.
4. Rotate the pump shaft and tap the side of the
cover gently until it reaches the position in which
the shaft rotates most freely.
5. Tighten the screws and make sure that the shaft
still rotates freely.
6. Install the drive gear onto the shaft.
7. Apply threadsealer (AGCO Part number 8366
62736) onto the nut threads.
8. Install the washer and the nut.
9. Tighten the nut to the correct torque value.
Figure 197.
A
A Nut
10. Hold the oil pump in a vice.
11. Check the end float between the gear and the
pump body.
11.1. Make sure that the clearance is within the
specified limits.
Dimension: 0.03 –0.11 mm
11.2. If necessary, adjust the number of gaskets
between the cover and the pump body.
Figure 198. End Float Check
12. Install the oil pump.
Refer to: PIL 15-60-00.
22. 15 - Engine
63 - Mount
00 - General
15 - 172 9813/3600-3 15 - 172
Check (Condition)
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Tilt the operator station.
3. Open the engine compartment cover.
Refer to: PIL 06-06-06.
4. Check the security of the bolts on the left and
right gearbox mounts.
5. Check the security of the bolts on the left and
right engine mounts.
Figure 201.
A
A
B
B
A Gearbox mount
B Engine mount
23. 15 - Engine
63 - Mount
00 - General
15 - 173 9813/3600-3 15 - 173
Remove and Install
You must remove and install the engine and the
gearbox together as a complete unit.
Remove
1. Make the machine safe.
Refer to: PIL 01-03-27.
2. Remove the operator station.
Refer to: PIL 09-00-00.
3. Remove the engine.
4. Remove the bolts 3 from the gearbox and the
engine chassis mounts.
Figure 202.
BB
BA
BB
BA
BB
BB BA
BA Bolts 3 BB Mounts
Install
1. The installation procedure is the opposite of the
removal procedure. Additionally do the following
step.
2. Clean the engine, gearbox and machine chassis
thoroughly.
3. Check the condition of the engine and gearbox
mounts. If necessary, replace any damaged
mounts.